BT file transfer in standby - Tilt, TyTN II, MDA Vario III General

Hi, is there a way to make the kaiser accept a file transfer via BT while in standby? I don't understand whether it's a by design behaviour or a technical issue. BT connection with car's handsfree works ok, so I thought that BT is always active.

No, to save battery, bluetooth will also goto standby mode! However I think there should be some registry hack for this. Anyone?
Regards,
Carty..

Related

Multiple bluetooth connections?

I wonder if anybody knows if it is possible to have two (or more) divices connected at onceon a Blue Angel?
eg. Tom Tom 6 plus a hands free connection.
I have tried every configuration I can think of, different ports ect, but to now avail.
With the gps connection up and running, as soon as you turn on the hands free , the gps connection link is lost, turn off hands free and it will resume connection.
I am using BA WM5 AKU3.5 R4 - xplode's excellent rom
In GPS settings
Program is using COM 5
Hardware is using COM 0
Manage GPS settings set to Auto
In Device settings,
BTGPS unit is on COM 0 (Serial box ticked)
Hands free is unassigned
Any help will be much appreciated.
any idea's anyone?
On Last Baniaczek's ROM I made an experiment just a moment ago: BlueAngel, Navigation system (Polish one, Automapa), plus GPS on Bluetooth and A2DP headset - first connected headphones, then added GPS (using automatic GPS connection - it's M$ Stack) - Everything seems to be working fine. I thought it was a bit unstable at first, but AD2P stops sending data, when there is no sound from the device.
GPS Settings are default: COM6 for applications and GPS has COM7 assigned on Hardware tab and in Bluetooth outgoing port. Quite seamless.
then I made the 2nd one: same headset connected in Handsfree mode: indeed turning on navigation made it connect and disconnect every few seconds.
For me it seems to be fault of M$ BT stack: it cannot hold 2 similar streams on BT (COM and Handsfree/Headset are both typical serial connections of highest priority in BT stream). At the same time it can cope easily with two different streams (A2DP is lower priority, high-bandwidth BT connection).
I'm not sure, but I think when I used old Helmi 1.3.2 with Widcomm stack it could cope with GPS and Handsfree at the same time, but it needs more testing.
jakubd is right it is limitation in MS BT Stack
Don't give up and it should start to work. I have similar problem with BT GPS and BT headset. GPS goes on and off while headset is on. And than I try to switch headset off and on, BT off and on, GPS off and on and after some time it start to work together with no problem. It takes first 10-15 minutes of my voyage but then it works for the remaining few hours.
Sorry, but I still didn't find out what combination make it work. If I do, I will post it here as workaround.
And I'm almost sure that I had no such problem with Helmi 1.4 ROM.
Thanks guys,
have tried every configuration I can think of, but its always the GPS connection that is dropped, not the hands free, this would not be a problem if it was just when you are answering a call.The GPS reconnects only when you disconnect the hands free connection. ?
Has anyone Successfully used the Widcomm stack with this type of setup?
I am sure alot of members would find this usefull if it can be made to work!
This is my experience:
ROM : Helmi_BA_WM2k5_AKU3.5_v1.4.CF2.R2 (baniaczek)
Tom Tom 6
GPS : Bluetooth
Headset : Nokia BH-300
When the headset is on and connected, the GPS doesn't work (TT say no GPS found). When I turn off the headset, the GPS is working.
With ActiveSync I have the same problem: when the headset is turned on, I can't establish a connection with the PC via bluetooth.
BUT!
If I use a different headset, a Logitech HS03, all is working fine. I can leave the headset on and the GPS is working. I can receive incoming calls with no problem (using the headset) while I'm driving without loosing GPS signal.
With ActiveSync is the same: I can connect my PC with the headset on.
I have no idea why there is this difference with these two headsets, but one is working and the other no. I don't know if the problem is the MS BT stack, but my test demonstrates that under some circumstances this stack could manage more than one connection at time.
bigmike said:
I don't know if the problem is the MS BT stack, but my test demonstrates that under some circumstances this stack could manage more than one connection at time.
Click to expand...
Click to collapse
Bigmike, my point exactly. As I wrote in my post I keep turning on and off until finally it works. So there are some circumstances under coexistence is possible.
It seems that devices try to use same port which means that first device does not reserve port for itself. I am not an expert but it seems if we could somehow force devices to use different ports problem would be gone.
bigmike said:
If I use a different headset, a Logitech HS03, all is working fine. I can leave the headset on and the GPS is working. I can receive incoming calls with no problem (using the headset) while I'm driving without loosing GPS signal.
Click to expand...
Click to collapse
If this works with one set and doesn't work with another, it might be connected to list of profiles supported by the headset:
1. Headset - HSP - more common, typical profile for use with cell phones (supports AT commands)
2. Handsfree - HFP - audio-centric, used mostly in cars, less common
http://en.wikipedia.org/wiki/Bluetooth_profile
My SonyEricsson HBH-600 has both profiles (checked with services list on SonyEricsson phone), but I don't know how to select which profile is used by headset.
Just a thought...
sassa said:
Bigmike, my point exactly. As I wrote in my post I keep turning on and off until finally it works. So there are some circumstances under coexistence is possible.
Click to expand...
Click to collapse
I hope you haven't misunderstand my previous post. I haven't in mind to minimize the value of your post (very useful is someone will try to investigate about this problem).
I was thinking that somebody, reading your contribute, could wrongly think: “you're are a lucky guy and turning on-off the headset repeatedly you crash some library and the two devices are working together”.
My intention was to remark the fact that under some circumstances the headset and the gps can connect together every time and always at first try: it's not lucky, crash or random events.
jakubd said:
If this works with one set and doesn't work with another, it might be connected to list of profiles supported by the headset
Click to expand...
Click to collapse
I have a similar thought.
It seems to me that some times ago I have read that it should be possible to change some profile's parameters “playing” with the registry.... but I could be wrong...
bigmike said:
I hope you haven't misunderstand my previous post. I haven't in mind to minimize the value of your post (very useful is someone will try to investigate about this problem).
Click to expand...
Click to collapse
No I have not, bigmike, just the opposite. I was delighted that somebody confirmed my point.
bigmike said:
My intention was to remark the fact that under some circumstances the headset and the gps can connect together every time and always at first try: it's not lucky, crash or random events.
Click to expand...
Click to collapse
Couldn't agree more. And I think it's worth trying to resolve it.
Multiple BT connections - solution?
I think I find a solution for this, or maybe we can call it workaround. At least it works for me.
As I wrote in my previous posts, I could make it work every time just didn't know how. Now I established repetable procedure which worked every time for reasonable number of experiments.
Secret was to turn on BT headset (in my case Plantronics) and BT GPS device (Haicom 406-BT) and GPS program (iGo) first, and then go to Comm Manager and turn bluetooth on.
So my procedure is:
1. make sure that BT is off in Comm Manager
2. turn on BT headset
3. turn on GPS device
4. open iGo program
5. minimize iGo
6. turn on BT in Comm manager
7. open iGo and make sure it's connected
8. go to phone and call myself just to make sure it works
9. back to iGO and make sure it works
If 8 or 9 fails for the first time, just turn BT off and on again in Comm manager and check it again. I never need to do this more than twice.
Try this, guys, and good luck.
P.S. I don't know if it matters, but make sure that in Settings/Connections/GPS "GPS program port" and "GPS hardware port" is set to (None) and "Manage GPS automatically" unticked.
Very good! Many thanks Sassa!
I have tried for two times your procedure and both tries worked very well (with TomTom6 and Nokia BH-300)
I use a slightly different procedure:
1. BT off in Comm Manager
2. turn on BT headset
3. turn on GPS device
4. turn on BT in Comm manager
5. open TomTom 6 (wait some seconds and make sure it's connected)
6. go to phone and call myself (on the first call the headset is disconnected)
7. back to TomTom and make sure it works
I have noticed a different behavior of the BT headset having the BT always on (in Comm Manager) and using this procedure... but I need to make some tests before writing more.

how to "speed up" a2dp / bluetooth. HELP!!!!!

I need some serious help please.
Situation: My car has bluetooth for phone but not music. So i bought an A2DP FM transmitter. I am trying to use both in the car. one for phone, other for music. problem is, when both bluetooth devices are connected, the music SKIPS horribly.
I've tried a bunch of different roms and radios and tried the a2dpfix and everything I could find.
Basically, when i disable the car bluetooth, the skipping stops.... so it's the radioload or the workload on the tilt that makes the music skip.
So......
1) what can i do to increase bluetooth performance or general system performance?
2) what is the best rom or radio for bluetooth performance?
3) what is the best setting for bluetooth performance in registry? bitpool? framerate? jointstereo?
4) what is the music player using the least amount of resources?
THANK YOU. Please help with knowledge, not speculation.
also, any thoughts on prioritizing bluetooth devices or signals to give higher priority to a2dp?
overclocking?
j_bowl said:
radioload
Click to expand...
Click to collapse
Most likely. Several people have reported that issue. A2DP needs lots of bandwidth and realtime availability, if a second connection needs to be maintained at the same time it's very likely to cause interruptions.
j_bowl said:
I need some serious help please.
...snip...So......
1) what can i do to increase bluetooth performance or general system performance?
2) what is the best rom or radio for bluetooth performance?
3) what is the best setting for bluetooth performance in registry? bitpool? framerate? jointstereo?
4) what is the music player using the least amount of resources?
THANK YOU. Please help with knowledge, not speculation.
Click to expand...
Click to collapse
What I did to fix this problem was to purchase the new Motorola FM transmitter - it does BOTH on one device - it transmits music to the radioo and gives you hands free for phone - really works well - much better than the Parrott that was in the car to begin with.
Bill
I saw the Motorola FM Transmitter but decided to go with my Satechi model because 1) it starts up automatically with ignition and 2) I can hide it away in the glovebox instead of having it attached to my visor.
so the best set up was to use both at the sametime but i'm not sure if i can anymore.
anyone know how to dedicate more resources to radioload or set priority in task manager?
THANKS
No.
A possibility, which depends on your Satecho thing, is if possible not to connect it to the Kaiser (leave it on, paired, but don't expressly connect to it when getting in the car).
That way there's no active BT connection between teh 2 so you shouldn't get skips. When you receive/place a phone call, the Kaiser will search for a present known handsfree and connect to it automatically anyway.
how do i pair it and not connect? when i get in the car, the car handsfree connects automatically.
j_bowl said:
I need some serious help please.
3) what is the best setting for bluetooth performance in registry? bitpool? framerate? jointstereo?
THANK YOU. Please help with knowledge, not speculation.
Click to expand...
Click to collapse
Did you happen to do any registry tweaks to maximize the performance of the A2DP BT Stereo performance in the past by increasing the Bitpool and MaxSupportedBitPool DWORD. I found on my Vogue that I lost simultaneous BT connection when I altered those settings from default. I now leave the registry A2DP settings at default and have not had problems with simultaneous BT connections (hands free, BT stereo and BT GPS puck).

Diamond Bluetooth HeadSet Bug

Ok, not sure if anyone got the same problem as mine, but here is my problem:
I have a Diamond using AZTOR v7 Rom, radio vBS14 if that matters and Sony Ericsson DS205 as my headset. I start my bluetooth on my diamond and can pair up with the DS205 without any problem. I can also listen to music without lag and sound is also crystal and solid.
When there is a call kicks in, I can answer the call by pressing a button on my DS205..... However, the problem comes when I end my call, the headset will be disconnected afterward and I have to manually press a button on the DS205 to make it reconnect. Each time when I make a call or when I receive a call the headset will be disconnected.
Luckily (or not), I found a workaround: Whenever I pair up my headset, I need to go to Setting -> Bluetooth -> and "Refresh" the services that I want to enable on the DS205 headset. That involves un-checking the services enabled (including "Wireless Stereo" and "Hands Free") and re-checking the services again. After I have done this "resetting", the disconnection problem I described above will be gone.....
Each time I restart the phone or have the bluetooh disabled on the phone, I need to go through that manual procedure again to make my headset work perfectly.
As you can imagine, that is quite annoying.......does anyone have the same problem as me?
I don't have this problem, but i have another problem, when i use the orignal rom, i can use my headset(jabra bt3030) in my diamond and it will automatically connect to use hands free and wireless stereo mode when i turn on bluetooth, so when i change to use swift 7.5 full rom, i have to resetting the bluetooth in diamond everytime when i close bluetooth
I can only get wireless stereo for my Plantronics Bluetooth Stereo headset. Any ideas why I can't get hands-free. Radio issue?
It was possible with some earlier ROM, but I can't remember which... (yes, I'm a flashing addict).
I'm having the same exact problem & it's annoying as hell. At this point, I can't get the bluetooth function on the phone to activate at all. I use the same bluetooth on another phone with no problems whatsoever, so I know it's the phone. I'm running the original rom.....not a flasher.
Have you tried Jetware?
Sorry, just installing this doesn't change anything. Still no hands-free.
Is there a specific option you want us to set?
shinji_lee said:
Have you tried Jetware?
Click to expand...
Click to collapse
lit2fly said:
... Each time when I make a call or when I receive a call the headset will be disconnected.
Luckily (or not), I found a workaround: Whenever I pair up my headset, I need to go to Setting -> Bluetooth -> and "Refresh" the services that I want to enable on the DS205 headset. That involves un-checking the services enabled (including "Wireless Stereo" and "Hands Free") and re-checking the services again. After I have done this "resetting", the disconnection problem I described above will be gone.....
Each time I restart the phone or have the bluetooh disabled on the phone, I need to go through that manual procedure again to make my headset work perfectly.
As you can imagine, that is quite annoying.......does anyone have the same problem as me?
Click to expand...
Click to collapse
Yes - I have a very similar problem with my jabra SP700. The Diamond 'forgets' the wireless bluetooth mode every time I disconnect the two devices (although the Stereo Bluetooth icon is still showing in the status bar).
For a short while I was having to re-pair the devices every time I got in the car - until I found the same workaround as you.
There must be a proper solution???
Hello, I had that problem in my HTC Diamond with Pioneer DEH-700bt and my jabra 3030 and she solves when changing in the registry the key to it that identifies the device in pocketpc HKLM/Software/Microsoft/Bluetooth/Sys the key "COD" and I introduced the value decimal 5898764 that identifies the device in smartphone
luck
juanfervs said:
Hello, I had that problem in my HTC Diamond with Pioneer DEH-700bt and my jabra 3030 and she solves when changing in the registry the key to it that identifies the device in pocketpc HKLM/Software/Microsoft/Bluetooth/Sys the key "COD" and I introduced the value decimal 5898764 that identifies the device in smartphone
luck
Click to expand...
Click to collapse
I have this value in COD key but I have the problem anyway.
Any solution to this annoying problem?
i use my diamond with my bluetooth handsfree kit in the car, it is classed on the phone as a headset though. the sound is ok, a bit echoey but ok. but the microphone doesnt seem to pick up my voice, i have to really shout for people to hear me, on my old Xda Orbit it worked fine. any ideas?

Autoconnect A2DP when in range?

Hey Guys!
Is there a way to tell WM6 to automatically route Audio through A2DP as soon as a paired device supporting the profile is connected?
Clarification:
When using a Hands-Free-Headsetfor telephony you can pair it once, then turn it off, after that it is automatically connected to the phone as soon as you turn it on again.
In contrast to that a Bluetooth Stereo headset is not automatically connected, you have to manually activate it in Bluetooth Settings first before you can listen to music through it.
Especially with my car stereo used as "A2DP Headset" (which loses power every time the ignition is turned off) this can get highly annoying.
Is there a way to tell Windows to automatically "use" A2DP-Peripherals when available?
Try A2DP Toggle: http://www.teksoftco.com/index.php?section=freeware
The Today-plugin migt reconnect automatically, but it has a memory-leak...
To easily manually reconnect, you can create a shortcut to the exe:
\Program Files\Teksoft\A2DPToggle\A2DP.exe
Then you can put that program on your today screen easily.
And if you want a nice icon with that shortcut, you can change the shortcut file to:
53#"\Program Files\Teksoft\A2DPToggle\A2DP.exe" "-a2dp:1"?\Program Files\Teksoft\A2DPToggle\settings.exe,-0
downloadtest82 said:
Hey Guys!
Is there a way to tell WM6 to automatically route Audio through A2DP as soon as a paired device supporting the profile is connected?
Clarification:
When using a Hands-Free-Headsetfor telephony you can pair it once, then turn it off, after that it is automatically connected to the phone as soon as you turn it on again.
In contrast to that a Bluetooth Stereo headset is not automatically connected, you have to manually activate it in Bluetooth Settings first before you can listen to music through it.
Especially with my car stereo used as "A2DP Headset" (which loses power every time the ignition is turned off) this can get highly annoying.
Is there a way to tell Windows to automatically "use" A2DP-Peripherals when available?
Click to expand...
Click to collapse
Yep. The WM bluetooth stack sucks. It works better with some stereos though. I tried it out in the store with I believe a Pioneer (with bluetooth 2.0) and it was perfect. Turned it on and a2dp connects. Switch to another input and a2dp disconnects. Switch back to bluetooth audio and it connects. It was flawless. I ended up ordering the kenwood built in bluetooth unit (bluetooth v1.2) and it is terrible. I must manually toggle the bluetooth connection (I use a program that I wrote to do so, kinda similar to the above the above poster posted). Also, sometimes after a call comes in it wont reconnect. Sometimes i must power off then on the headunit a few times. Wasnt this thing supposed to make things easier?! A real shame because I love everyting else about the kenwood head unit. It works better with some ROMs on my phone (this is with a tilt; xperia on the way ).
Yeah, A2DP Toggle works for me as well, It's just dumb that this phone cant just do that itself. My old W880i could! I'm using a Sony DR-BT21G headset
JKingDev said:
A real shame because I love everyting else about the kenwood head unit. It works better with some ROMs on my phone (this is with a tilt; xperia on the way ).
Click to expand...
Click to collapse
A story to learn before you you buy the head-unit I spent almost an hour at Fry's to try many units w/ my Tilt as well (Sony, Pioneer, Kenwood, JVC ...etc) and ordered online w/ the JVC unit. Excellent sound (compare to other model) but disconnect after phone call issue exist. I believe it's HTC fault since my Eten M600 (MS BT stack) and Asus P525 (Widcomm) doesn't have this issue (but others....). But I got to admitted HTC one do have the best sound quality.
BTW, my JVC BT-1 will auto connect my X1/Tilt when I start my car and I think it serve my purpose.
Solution
wensing said:
Try A2DP Toggle: http://www.teksoftco.com/index.php?section=freeware
The Today-plugin migt reconnect automatically, but it has a memory-leak...
To easily manually reconnect, you can create a shortcut to the exe:
\Program Files\Teksoft\A2DPToggle\A2DP.exe
Then you can put that program on your today screen easily.
And if you want a nice icon with that shortcut, you can change the shortcut file to:
53#"\Program Files\Teksoft\A2DPToggle\A2DP.exe" "-a2dp:1"?\Program Files\Teksoft\A2DPToggle\settings.exe,-0
Click to expand...
Click to collapse
I have created an application wich runs the commandline setting automaticly, so you never have to do anything again it connects automaticly. You can find it here: http://forum.xda-developers.com/showthread.php?t=502549

Pairing the Bluetooth with Jabrasp700?

Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Edris said:
Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Click to expand...
Click to collapse
I have the same problem with my SP700 and my Tritton BT stereo headset.Phone calls work almost all the time through the SP700 speaker, but playing music or through the FM radio seems to be a problem. I can get them to pair up sometimes by only checking the Wireless Stereo box. It works for a few times, but then I have to delete and re-pair again.
I've searched for all over for answers, but nothing seems to be a permanent fix. It's very frustrating to use my devices for anything else but phone calls.
Just to add a bit of info, I do not have any problems with my old Motorola HS820. Of course, I'm not using SP700.
Hope that helps your troubleshooting.
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Possible solution
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Edris said:
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Click to expand...
Click to collapse
Thanks! Nice App! Tried it with my Tritton BT stereo headset and it works! Had to install to my device instead of Storage card, then had to delete and re-pair, but it so far I can toggle between on and off Stereo Headphones without any problem. Will try on my SP700 shortly.
I attached the Cab if anyone else wants it.
Thank you!
Works with SP 700!!!!!
Mal Bridgeman said:
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Click to expand...
Click to collapse
When the software loads, follow the instructions, do not install with any of the microsoft wizards that pop up, it will install itself. I couldn't find anything that lists what changes that were made.
SP700 Firmware
FYI,
I too had the same issues and downloaded the sp700 firmware update. I thought the same thing about the drivers, but called Jabra and they told me the firmware update has the drivers embedded in it. When you start the install you cannot plug it in till it tells you to. After you plug it in it installs the drivers. But BEWARE I have not been able to complete the upgrade, it stopped halfway and bricked. I called support and they said there is nothing to do, but luckily I bought it from Costco and they returned it. So being not so bright I tried it again but on a different computer (thinking that there might be a conflict) and it didn't even load and bricked it again. So I returned it yet again. So then I gave up on Jabra support and found A2DP toggle. It works good enough, so I am leaving it at that....
Take Care
David
Tilt WM6.1
andrew-in-woking said:
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Click to expand...
Click to collapse
I have the exact problem that you are having with the new, Hyperdragon IV, ROM.
Is this A2DP Toggle really the only way - I mean what's the difference between pressing a button on my Kaiser to reconnect and pressing the button on the SP700 ??
I have tried using Mortscript as shown http://forum.xda-developers.com/showthread.php?t=382172&highlight=a2dp&page=2 Although I edited the end out because it kills the player after ending a call. This hasn't helped either
I am off to see if the same problems occur with my lady's N96. If not and no good solution can be found for this I may have got her a new present.
Aren't I nice ?!
Found another possible solution, it,s called zoA2DP. So far it works flawlessly between my SP700 & stereo headset without having to toggle anything or change any settings. When you install it, delete your original pairings and add them again, make sure that hands free & wireless stereo are checked in advanced options on you BT settings. I believe this is a registry mod, there are no icons or any noticeable applications running in the backround.
The thread is here
http://forum.xda-developers.com/showthread.php?t=279127
Cab file attached

Categories

Resources