Database Develop

Help needed - Trin won't update with any rom (3.5.2 LVSW Edition)

Hello,
I have this rom : RUU_Trinity_LVSW_WWE_1.25.0.8_GPS (AKU 3.5.2)
from http://forum.xda-developers.com/showthread.php?t=302198
I wanted to test the new WM6 roms, unfortunately, my trin doesn't update with any rom I tried (Orange, HTC, LVSW Wm6, Mun_Rus Wm6, ...)
It tells me : "ERROR 262 : UPDATE ERROR
... communication error during the process"
I'm stuck on LVSW Wm5 rom :'(
Not sure if Des SPPL is causing this problem... anyway, I tried to update it from Bootloader or synched, on XP and Vista, 5 differents roms... no luck.
I would really appreciate some help, thanks

can you list the steps of what happened, in order?
also, just to make sure i understand, have you already tried to manually enter the bootloader and THEN run the RUU? *edit* one last question, have you tried this.. after the error, leave your device connected and in bootloader, then restart the RUU.. can you give me your device details too?

Well, when I run the update with normal step (connect AS, then launch update...) when the update is ready to be started (progress bar appears), phone have to switch to bootloader, which it does. However, it seems that the RUU is waiting for that since it return me this error:
ERROR 246 : Device not responding
And I have to exit. I don't understand ?
Progress bar didn't even appear on the phone.
At this time boot loader shows
IPL-SSPL by Des
SPL-1.07.ds
So since I'm already in Bootloader mode, i try to launch RUU again. Here is the error I get when the progress bar appears on both phone and PC :
ERROR 262 : Update Error
And it offer me to recover the device, which I don't need as the current rom has been left untouched and is still functionning after the error.
Then I reset the device to enter bootloader this time:
IPL-0.50
SPL-1.06.0000
same error : ERROR 262 : Update Error
I'm kinda out of option, thanks a lot for your help !

well, it's been a pretty common thing for the RUU to give an error when the device goes in to bootloader (can't detect it for some reason). Most times, simply running the RUU again while the device is still in bootloader works fine.
Why don't you put hard-spl on just in case, manually enter bootloader (which will then be hard-spl) and run the RUU again. You shouldn't enter the bootloader manually unless you've loaded hard-spl or sspl on to your device. From what i understand you won't be successful from what you did after the hard reset. When your phone went in to bootloader the first time, it was with SSPL pushed to your device by the updater program to enable you to update safely. After resetting, you're back to your normal bootloader which won't help anything.
I know one time it did this to me, and wouldn't connect to my device. I started the RUU about 3 times in a row with my device on bootloader, and for some reason after the 3rd time it suddenly worked.. weird, i know.
anyway, hard-spl will make the whole process safer.. let me know if it connects or not, i'll see if i can help you troubleshoot

I wanted to install hard-spl, but it runs as a normal RUU and give me exactly the same errors as a normal run update (error stated above).
So I don't see how I could install it
Another thing weird, when I run a official HTC rom update, when the udpdate should start (device enter in boot loader, progress bar appear in bot PC an device), the Trin reset itself and boot as normal... of course the RUU gives an error due to this reboot ...
Same weird behavior with an official Orange rom...
Now I'll try with SSPL...
Oh and thanks a lot for your help

simply try to run twice ROMUpdateUtility.exe after error

Please read carefully what I have posted (and the steps I ran into)...
Already launched again RUU, it gives me an Update Error and the device is stuck on the screen that show the progress bar.
Need to soft reset... I can't launch again the RUU after that since the device is no longer recognised as connected on PC.

I confirm I can't manage to install the Hard SPL, even after laoding Des sspl from the device...
Defintly blocked

At last I have succeeded in upgrading the device. Seems like my bootloader was somehow corrupted or something... after doing another Hard Reset it have installed hard spl succesfully...
I had already done a hard reset before, so I don't understand what happened.
Nevermind, at last i can try wm6
thanks a lot for your help racerx_ anyway

hey no problem.. not sure that i actually helped haha.. but i'm glad you sorted it out. happy flashing!

Might it have been the USB driver on the desktopside ?
Did you see XP recognize and install HTC USB device again, after device disconnecting from AS and going into bootloadermode for first time ?...
Just a thought...

Not sure what it is, but it's happening again, can't update anything as the bootloader seems somehow corrupted.
When i enter bootloader it briefly display the 3 color, then grey screen with "loading" and then the hard spl screen from Olimpo... the only problem I see is that it does no longer display TRIN100, but only little dots (like if it was corrupted)...
Very annoying situation, and I have already done some hard reset, but nothing

So more exactly, where I start DES SSPL or when I enter Olipro Hard SPL (that I installed before WM6), it shows the good infos like :
TRIN100
xxxx
TRIN100
SPL-
But after 1/4 of second, it start loading for a very short moment
and display again the RGB screen with the infos except the "TRIN100" parts are like this ':':':':':':
Anyone has seen this before ???

@cedrick: You have a SD card inserted on this device, right? if so, remove the SD card and try again.
If the SD card is not the problem, then you might have overwriten the memory region where the ModelID is stored. I can help you to recover it if that is the case.

pof said:
@cedrick: You have a SD card inserted on this device, right? if so, remove the SD card and try again.
If the SD card is not the problem, then you might have overwriten the memory region where the ModelID is stored. I can help you to recover it if that is the case.
Click to expand...
Click to collapse
...... well well, that was simple hahaha (and I feel stupid lol).
yes I had my SD inserted (and I remember only now that the last time it worked I had indeed removed the mini-SD).
So, thanks to you I have understood this issue at last !
Muchisimas gracias por tu gran ayuda pof

Now the question is, wtf do u have on this SD card? LOL

Errr that's a good question... maybe it is time to clean those 4go of things (which most of those come from the SD I had on my Prophet, in the top of that)
Anyway, it's a rare specimen indeed... want a copy to play with heh ?

[HELP] installing new rom stuck on 99%

After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???

kevinalmere said:
After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
Click to expand...
Click to collapse
Always post the data of your your phone,to get help.
secondly you had a bad flash,perhaps your phone is CID locked. Which rom were you trying to flash ?
Now to recover,download the official carrier's rom and flash it while in bootloaders.The phone will start working again in default status,then,Read and understand the unlocking method and the flashing guide,read the stickies carefully and perform the method correctly.
cheers !

i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....

Help!!!
I have same Problem with TNE-V1.0n_4mb.exe
IPL 3.08
SPL 3.08

kevinalmere said:
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Click to expand...
Click to collapse
If you can go to boot loader, most likely you will be ok. When you plug in the usb port, does the words in the screen change from serial to USB? Once it changes, then flash your official, and then CID unlock your device (this is different from SIM unlock). Then flash to the ROM you want!!
PS: Go read wiki about how to unlock and flash and understand more about your device. http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard

The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?

kevinalmere said:
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
Click to expand...
Click to collapse
Vista dont like upgrading and stuff...but there is a work around, search the forum and see if you find it. Or try using XP.

okee problem solved working again
thanks for your help!!!

kevinalmere...
How did you resolve the issue I'm having very simular problems and believe it's my Vista OS causing the problem..
Orange SPV M600 G4
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20

OS 4.0.0.0
Sorry should explain my issue incase anyone can help.
I attempted an upgrade to WM6 using an Upgrade .Bat from this site. I was slightly impatiant due to not being able to complete the downgrade first anyway the upgrade frose, after a while I canceled the update and carried out a hard re-set... Since then I'm not able to boot nor connect to my desktop via Active sync (WMDC (Vista))
I've followed every instruction I can find but only to be meet with RUU Errors saying can't connect or file open. I can however acces my Bootloader screen and when connection is made the USB symbol shows on the screen of my phone...
Any help would be greatly recieved......

HELP ME! My Tilt Is Bricked.

Ok, so today I tried to flash my Rom with the official att 6.1 rom from HTC. I got it to finally start flashing after about ten tries but when it reached about 13% it gave me an error 276 I think. I tried the recovery method suggested by removing the battery for 3 seconds and reseting the device but now my device isn't recognized in windows and I can't run the upgrade file anymore.
It just goes to the bootloader screen with "KAIS1*0" on the top, then "SPL-3.02.000" below that, and "CPLD-8" below that. At the very bottom it shows USB but my computer doesn't recognize the device. I've tried hard reseting it and it just goes back to the bootloader screen.
Is there any way I can get my Kaiser back or am I screwed?? All this waiting for 6.1 and now my phone is dead. What a load of crap.

Just re start the ruu and let it sit for a minute when that happens, it will start again by itself. Almost shat myself when it happened to me.

First of all, relax. Your phone is not bricked. Do a little looking around the forums and you will resolve this.
I am too lazy to search for him but is the 3.02 SPL compatible with the 6.1 ROM?

I can't restart the Ruu because I can't get a usb connection to my phone. The bootloader goes into usb mode but my computer does not see the phone. The Ruu says it cannot detect the phone either.

Isn't there a way this guy can re-flash using a MicroSD card?

MineralGray02K said:
Isn't there a way this guy can re-flash using a MicroSD card?
Click to expand...
Click to collapse
I'm not sure if the OEM SPL has the ability to flash from card like the Hard SPLs.
To test put the Carrier ROM (Download from the Wiki) on to the root of the MicroSD Card and call it KAISIMG.NBH. Turn on the Phone with the Camera Button Held Down. It should try and flash the ROM then. If that doesn't work, I have a thread and wiki page all about getting stuck on the bootloader, check my Sig for more info.
Hope this helps.
Dave

rodavery said:
Ok, so today I tried to flash my Rom with the official att 6.1 rom from HTC. I got it to finally start flashing after about ten tries but when it reached about 13% it gave me an error 276 I think. I tried the recovery method suggested by removing the battery for 3 seconds and reseting the device but now my device isn't recognized in windows and I can't run the upgrade file anymore.
It just goes to the bootloader screen with "KAIS1*0" on the top, then "SPL-3.02.000" below that, and "CPLD-8" below that. At the very bottom it shows USB but my computer doesn't recognize the device. I've tried hard reseting it and it just goes back to the bootloader screen.
Is there any way I can get my Kaiser back or am I screwed?? All this waiting for 6.1 and now my phone is dead. What a load of crap.
Click to expand...
Click to collapse
run this while phone is hooked up to computer stuck in bootloader.

Sweet Jesus
Ok, I tried the tri-color fix from nufsaid. It didn't work b/c it couldn't open a usb port or didn't see the phone or something. Then I tried putting the rom on my microSD card.
And *SHAZAM* there it was. DaveShaw you are a god to me now. It said the update was successful but I'm still stuck in the bootloader. It used to work if I would plug it into the wasll charger and reset it but that isn't working now. My computer still doesn't recognize it so Mtty or anything still doesn't work.

Ok, I left my tilt on the tri-color screen all night long to run down the battery. When I woke up I tried to power it on and I got the familiar ATT flash screen but when I plugged it into the AC power it went straight into the bootloader.

I don't know what's worse, bootloader or red light of death, I just experienced the red light, called att and got a new phone sent out in 12 hours! What SPL does your phone show? they might exchange if it's not 'voided'

ok, I finally got it to load the windows. If the battery has a high charge or is charging resetting won't get out of the bootloader. If I let the battery run down to almost nothing, wait a little while with it out, then try it again it will turn on. my spl is now 3.56.0000.

Finally
I finally got it out of the bootloader. I'm never going to reset my phone again. It's gonna suck if it freezes. Thanks for all the help.

rodavery said:
I finally got it out of the bootloader. I'm never going to reset my phone again. It's gonna suck if it freezes. Thanks for all the help.
Click to expand...
Click to collapse
Glad your back up and running. There are two new hard SPL's be cmonex (they are mentioned in the link in my sig) that make it less likley for you to get stuck at the bootloader. You could try those?
Ta
Dave

Stuck on Splash, can't flash another ROM

A while ago I tried to Flash a version of WM6 from mfrazzz on my wizard. The installation seemed to go ok, but when I boot it up i coudn't get past the second splash screen. I thought the phone was a gonner until last night, when I gave it another shot putting on Button ROM. I followed these instructions and it worked. The instructions also had me unlock the phone, and that worked fine too. after that I tried updating my IPL and SPL, Right now my IPL is 1.05 and SPL is 3.08
After this I tried unsuccessfully to get WM6, I think I started off trying Faria.
(So here is the actual problem)
After I tried installing Faria unsuccessfully, I couldn't get Button ROM back up. I'm stuck on the second splash screen (picture of a mug of beer in front of the Colosseum). I've tried flashing my phone w/ everything i've got, including button ROM and Love, and nothing works. most of the WM6 Update Utilities won't even connect. Button Rom connects, stalls at 98%, finished and says it was a success, but I'm still hung up on the Splash.
(I'm running WinXP w/ SP2)
I really just want something running on this phone, don't care what it is.
Thank you for your time

Download official stock rom to recover back and download WST_4.2.2 to verify the CID lock/unlock status,most probably its still CID locked.or you can even reflash 'Button's Rom' again.

No, I've tried to reflash button rom many times. It says it works but it gets hung up on the splash. Since I can't get anything to run on it WST won't work (I think)

Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.

hEY ZABARDAST
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
I did this when my Wizard stucks on the splash...
Get mtty 1.04 i thin i dont remember exactly but the higher i ever saw.
kill process wcesscom in PC
conect the ppc on Bootloader
click on conection it shows USB if not... start up again the process
then a white screen appears
I type: task 28
then it works a little on some memory directions
I type: task 28 55aa [or something] (its better get the info on wiki cause it works on chip directly)
without unplug the PDA starts the RUU again...
It works for me...
This is a process for HTC Universal but it works on Blue angel and Wizard for sure!
wait a little i will confirm the steps and the exactly words to type in.

you might need clean the ROM or your flash ROM is overcooked.
I can repair your phone !

+ Que PPC said:
I did this when my Wizard stucks on the splash...
...
wait a little i will confirm the steps and the exactly words to type in.
Click to expand...
Click to collapse
Hey + Que PPC!
Have you confiirmed those values? And is your Wizard CID unlocked?
This would be great to confirm working so that all those with CID locked devices could get their phones back - without paying IMEI-check.co.suckourmoney.uk
@ twig2256
If your phone is CID unlocked try Drugstore's method of recovering Splash Screen frozen phones
cheers

YES
The values are the same for every DOC CHIP
When the MTTY conects to USB type exactly this...
task 28
(then it will work formating and cleaning the DOC
then it says succesfully clean
and now type...
task 28 55aa
it again works on the same process you can close the mtty without unplug your device... update your device with a Stock rom.
Actualy I have issues with mtty i dont know why i can acces to USB it say CMD GOD Damn can anybody helps...
This is the link that mestrini said for drug gsm store metod to unfreeze
http://forum.xda-developers.com/showthread.php?t=276963
Hey mestrini see this...
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
even if it is universal it work for Wizard i did it once it works for me. but now it wont why????

zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
can't solve my t-mobile mda

Need to CID Unlock, not in win6.

Hi,
I'm having a problem with CID-Unlocked. I've a branded MDA Vario III and some person tried, without unlocking, to upload a new firmware.
I can't come into wm6 cause it stalls after the startup logo is displayed. If trying the original rom the famous 270 corrupted error will be displayed (after 1%)
Also it looks like the kaisdiag/kaisimg on SD won't work, it stalls on the "Loading..." screen, or am i doing something wrong? The only place I could go is the tri-colour screen.
Any suggestions?

BommelDingNL said:
Hi,
I'm having a problem with CID-Unlocked. I've a branded MDA Vario III and some person tried, without unlocking, to upload a new firmware.
I can't come into wm6 cause it stalls after the startup logo is displayed. If trying the original rom the famous 270 corrupted error will be displayed (after 1%)
Also it looks like the kaisdiag/kaisimg on SD won't work, it stalls on the "Loading..." screen, or am i doing something wrong? The only place I could go is the tri-colour screen.
Any suggestions?
Click to expand...
Click to collapse
What does it say on the tri-color screen when you plug in to the PC.

First on the TRI-Colour i see is:
Serial and after plug the usb it says USB

BommelDingNL said:
First on the TRI-Colour i see is:
Serial and after plug the usb it says USB
Click to expand...
Click to collapse
Flash Hardspl then and after that flash to any rom you want. Click under my signature and read carefully of how to flash and if you want to keep your tilt warranty

Let me say that the warranty has allready been void.
However, all the time busy with jumpspl, currently with error 00068002. Tried with the original file from the provider. Didn't get stuck with this one but restarts himself.
I was allready trying lots of stuff, but still fails.
Which hardSPL would you suggest? Cause I allready tried:
HardSPL-3.07
HardSPL-3.56-force-USB
HardSPLv1
Still with no luck.

BommelDingNL said:
Let me say that the warranty has allready been void.
However, all the time busy with jumpspl, currently with error 00068002. Tried with the original file from the provider. Didn't get stuck with this one but restarts himself.
I was allready trying lots of stuff, but still fails.
Which hardSPL would you suggest? Cause I allready tried:
HardSPL-3.07
HardSPL-3.56-force-USB
HardSPLv1
Still with no luck.
Click to expand...
Click to collapse
3.34 Daveshaws and 3.29 try those.

I Tried 3.34, renamed to kaisimg.nbh, but the loader gets stuck on Loading... and that's it.. all the teme.
Even with 3.29.

BommelDingNL said:
I Tried 3.34, renamed to kaisimg.nbh, but the loader gets stuck on Loading... and that's it.. all the teme.
Even with 3.29.
Click to expand...
Click to collapse
Did you tried this http://forum.xda-developers.com/showthread.php?t=375583

won't work, but even tried it:
"YOUR DEVICE MUST BE IN CE AND SYNCED BEFORE RUNNING EACH STEP."
First time on my pc..

BommelDingNL said:
won't work, but even tried it:
"YOUR DEVICE MUST BE IN CE AND SYNCED BEFORE RUNNING EACH STEP."
First time on my pc..
Click to expand...
Click to collapse
I'm assuming that you already tried to hardreset your device right

Additional:
When using Kaiserunlocker I get stuck at 0% with the following error: Error 262..
Just took to long, i guess.
gmaniac2008 said:
I'm assuming that you already tried to hardreset your device right
Click to expand...
Click to collapse
I did.. several times

BommelDingNL said:
Additional:
When using Kaiserunlocker I get stuck at 0% with the following error: Error 262..
Just took to long, i guess.
I did.. several times
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=423486

Running all progs as admin?

Allways.. in win7 UAC is turned off and win xp pro, no limitations.