Wireless LAN Setup - Tilt, TyTN II, MDA Vario III General

The WiFi functionality of my AT&T Tilt was working then suddenly it couldn't connect to my home network. It displays the network as available but when it tries to connect, the icon turns to unavailable.
The home network is protected with WEP, but even if I remove the security, the phone will not connect.
I restored the phone to a very early Sprite backup when everything was working correctly and it still would not connect.
Is there something I could to (besides 'clear storage' that would reset WiFi?

perhaps it would help, if you go to:
start -> setting -> connections -> wlan -> energy-mode and set to optimized for performance
at me this gives a bit more speed at loading webpages, perhaps you will get a better connection
(perhaps this differs to you, cause i have a german rom and the workthrough above is translated in my mind )
bye andré

Thanks - I have done that and still cannot get a connection. It seems as if the HTC does not like something with my router (but that was not always the case).
Bill

deleting profile under wifi and resetup also won't work?
i run on wpa2 / psk security with no problems, perhaps an problem with wep?! but if you tried without security, this shouldn't be the problem
do you have the chance, to try your kaiser t another wlan at a friend or at work? to see if the problem is not your home-network

Thanks - will try another network just in case however I have 2 laptops currently running on the network with no problem.

edi said:
deleting profile under wifi and resetup also won't work?
i run on wpa2 / psk security with no problems, perhaps an problem with wep?! but if you tried without security, this shouldn't be the problem
do you have the chance, to try your kaiser t another wlan at a friend or at work? to see if the problem is not your home-network
Click to expand...
Click to collapse
i have the same problem, i can't connect most of the open wifi networks (either home network).
could you post your ROM's versions? radio version, etc, etc?

wifi
Anyone found a solution for this? i also expierience the same problem

Same problem, I tried everything from changing settings on the phone, on the router. Hard reset, soft reset...etc. I am running the stock HTC rom 1.56.405.5 and radio 1.27.12.11
Any help??

same here... i tried flashing wm6.1 with newest radio and nothing changed..... except wm6.1

Related

The massive wifi problem that many experience

When I turn on my phone at work, the wireless connection (open unsecured) connects and works for a few minutes. After some time, it disconnects and without rebooting my phone, I cannot establish a wlan connection.
This is oly the case at work. At home it works flawlessly, but it is another network kind.
Anyone found a solution to this problem? I saw a lot of threads about this but no good answers.
I am using duttys v3.
Not sure. Perhaps there is some sort of time out on your work network for inactive devices, or dhcp ip releases or something weird and "networky" like that?
Or perhaps your phone is going into a power save mode if you are not using it?
Just general ideas, I don't have this particular problem
I dont think many people have this issue! you must not have a setting correct, try downloading KaiserTweak and adjusting the timeout and also take a look at the routers settings I find it strange that a business would have an open network for security issues
austinsnyc said:
I dont think many people have this issue! you must not have a setting correct, try downloading KaiserTweak and adjusting the timeout and also take a look at the routers settings I find it strange that a business would have an open network for security issues
Click to expand...
Click to collapse
I work at the university, and the network is unsecure. You have to enter login and pass at a webpage to gain access.
I cannot reconnect at all once ive been disconnected. So it should have anything to do with kaisertweak or timeouts.
I have tried every setting and combination. I have tried to select work/internet settings. Ive tried to tell the phone its a hidden network / not hidden network. I have tried to use power save / performance mode. Ive tried to turn off 3g, bluetooth, phone (everything basically).
When I tap connect, it says connecting and then it immediately goes to "active" and tries to connect to another network (which I dont have access to).
solwretep said:
When I turn on my phone at work, the wireless connection (open unsecured) connects and works for a few minutes. After some time, it disconnects and without rebooting my phone, I cannot establish a wlan connection.
This is oly the case at work. At home it works flawlessly, but it is another network kind.
Anyone found a solution to this problem? I saw a lot of threads about this but no good answers.
I am using duttys v3.
Click to expand...
Click to collapse
I have worked out the problem.. first if its a WPA enterprise connection, make sure its set to WORK and not INTERNET setting. it will work. my only works with schaps versions not duttys
on my old pda (Acer N50 premium) I had the same problem with my unis network... it would only work (if at all) for a few minutes then nada... but at home it was absolutely fine, quick stayed on and totally responsive... I wonder if it has something to do with the rubbish way unis run their IT...?
Wasted thread
Many do not have this issue.
According to what's being said here by the indiviuals with issues, you're having problems connecting to a certain network...not all networks.
If it were all networks; your device, settings, equipment or rom would be the common denomenator. Since it's one network, it's that network.
Just because a network is or appears to be available, that doesn't mean that you can connect to it.
dwny said:
Wasted thread
Many do not have this issue.
According to what's being said here by the indiviuals with issues, you're having problems connecting to a certain network...not all networks.
If it were all networks; your device, settings, equipment or rom would be the common denomenator. Since it's one network, it's that network.
Just because a network is or appears to be available, that doesn't mean that you can connect to it.
Click to expand...
Click to collapse
no, it could be the phone software. Lets says that a string is added to the registry if the network you are connected to disconnects you; a string that makes the phone cancel connections to the network. And lets assume that the network disconnected you because there is a hidden firewall in the phone software that blocks ping requests, thus making the network believe that the connection is lost and thus disconnecting you. Then we have a moment 22, which is basically something wrong with the phone.
As some readers already pointed out in this "wasted thread", when changing the rom (in one case) or when changing settings from "internet" to "work" (in the second case) there is a great possibility that this problem in fact has to do with phone software and not network.
In my case, it just happens to be neither of the mentioned solutions or any solution that I have found in other threads.
One thing you may want to check is that your wifi is set to max performance. The issue may also be that there is a DNS cache issue, in most cases it can be resolved by manually reconfiguring the connection.
I have been successful in configuring my phone's WLAN to connect to everything from open APS's, WEP, WPA, RADIUS and AP's with proxy redirects, so I can tell you that as with most cases, it's human error.
I have tried max performance.
How do I resolve a dns cache issue? Manually reconfiguring the network did not help (only thing that helps is a reboot).
seattleweb said:
One thing you may want to check is that your wifi is set to max performance. The issue may also be that there is a DNS cache issue, in most cases it can be resolved by manually reconfiguring the connection.
I have been successful in configuring my phone's WLAN to connect to everything from open APS's, WEP, WPA, RADIUS and AP's with proxy redirects, so I can tell you that as with most cases, it's human error.
Click to expand...
Click to collapse

Connecting to Home Network Problems. Help Needed Please......Perpetually Connecting

I cannot access any webpages using my tilt I only get the message "cannot connect with current connection settings" no matter what webpage. What exactly am I to change the settings to? I'm using a Linksys Speedboost with WPA2 security. The Tilt is picking up my network so I hit connect. When I look under Settings/Connection/Wifi I see my network but its just says "connecting" all the time. Shouldn't it say "connected"? Then I checked the Wireless LAN I see me network and the signal strength is full. What gives? I've disabled all the ATT data connections with the NoData program. I've also cleared all history and done a soft reset. Any help would be greatly appreciated.
I presume you have tried removing from and adding the network to your Kaiser. And I presume you have rebooted your Kaiser and router without any effect?
Were you able to connect to other networks in the past? Have you changed any settings recently that might have caused the problem (by accident)? Have you tried the different power modes?
The problem might not be your Kaiser; it wouldn't be the first time it had something to do with the router itself.
Have you upgraded your router with the latest firmware? Is MAC-filter security enabled?
Just thinking...
Yes I've tried removing and letting the phone find the network again to no avail. I'll try again when I get home. The phone and router have both been rebooted also to no avail. I've never been able to connect. Just got the phone late last week. Not familiar with changing power modes so I haven't tried that. The router does have the latest firmware. I've see a few other networks besides mine listed. Several of them said unavailable and I'm not sure what that means.
Well deleted all the networks to let the phone fin them again. Now it says connected but still will not bring up any web pages.
Sorry to say, but I have no direct solution to your problem. So let's troubleshoot your problem.
Download and run VxUtil. The tool can be found here:
ftp://ftp.cam.com/cambridge/win/vxUtil.zip
Open the .zip file and install "vxUtil.ppc3_arm.CAB" to your Kaiser. Leave the rest of the cabs.
Try to ping your router, other computers on the network and internet sites. See what the results are and if there is a difference between LAN and WAN adresses.
If you own a Tilt, you could also try to remove the hidden proxy. Fix it by installing the folowing .cab found here:
http://forum.xda-developers.com/attachment.php?attachmentid=71206&d=1203325282
If it wouldn't help, you can restore the proxy here:
http://forum.xda-developers.com/attachment.php?attachmentid=71207&d=1203325282
Have you already tried another brower? Like Opera mini? Find it here:
http://www.operamini.com/
Or you could try the 'full' version found here:
http://www.opera.com/products/mobile/
Let's hope you find the solution or at least a lead.

Tilt Wi-Fi Problem after WM6.1 Upgrade (official)

Hi, I've had my Tilt for a while now, and I just updated to the new WM6.1 ROM this morning. However, after the upgrade, I could no longer get the wifi to work. I can connect to the wireless networks (tried different networks both open and secure), but when I try go to a website or use the internet, it just sits there and then says cannot connect. I have tried everything I can think of to fix the problem. I tell it to connect through work and through the internet, and messed with some other setting but that wouldn't do it. I plugged the tilt into activesync and it used the computer's connect just fine. Anyone having or had this issue, or have any suggestions?
Chris
Did you install the remove hidden proxy CAB?
If not, go here and get it:
http://www.4shared.com/dir/6996097/3f1f5d36/cabs.html
It's the removeHiddenProxy4CWS_0522 file
There may be others that do the same thing.
I installed the hidden proxy cab on my tilt, and the wi-fi still isn't working. Any other suggestions on fixing this problem. It's killing me. I though I'd be able to upgrade and reinstall all my files in just over an hour before I ran into this issue.
Update: Okay, I reverted back to the previous WM6 ROM and the wifi worked with absolutely no problem right off the bat. I don't understand what the issue could be and whether anyone else is having the problem. I'm going to try the WM6.1 ROM one more time, and then give up. I have to have wifi because I'm not willing to fork out money for a data plan. Any solutions or suggestions would be greatly appreciated.
change the power mode for the wireless mode to 'Best Performance'. This worked for me. Start -> Settings -> Connections -> wireless lan -> Power mode -> Best Performance.
Work Around For Wi-Fi Problem
I have found a work around for this and have tested on my "Tilt" which works 100% for the windows mobile 6.1 rom. On your device go to start, settings, connections then click on the connection icon then manage existing connections. Create on new setting on top of Media Net settings which you will have two connections. Name it Cingular GPRS, Enter Cingular GPRS, then Cellular Line (GPRS, 3G) for your modem, click next access point name wap.cingular, click next then User name [email protected], Password encrypted. The only thing you need to do is when using the internet & text messaging to have settings set on bullet mark Cingular GPRS. When using MMS only check check bullet mark for Medit Net and have proxy settings enabled at all times which will not affect your Wi-Fi connection to browser the internet once you switch back to Cingular GPRS in your settings. https://www.wireless.att.com/suppor...tutorialsCategory=MEdia+Net&tutorialId=614410
Park said:
I have found a work around for this and have tested on my "Tilt" which works 100% for the windows mobile 6.1 rom. On your device go to start, settings, connections then click on the connection icon then manage existing connections. Create on new setting on top of Media Net settings which you will have two connections. Name it Cingular GPRS, Enter Cingular GPRS, then Cellular Line (GPRS, 3G) for your modem, click next access point name wap.cingular, click next then User name [email protected], Password encrypted. The only thing you need to do is when using the internet & text messaging to have settings set on bullet mark Cingular GPRS. When using MMS only check check bullet mark for Medit Net and have proxy settings enabled at all times which will not affect your Wi-Fi connection to browser the internet once you switch back to Cingular GPRS in your settings. https://www.wireless.att.com/suppor...tutorialsCategory=MEdia+Net&tutorialId=614410
Click to expand...
Click to collapse
Hi, I tried you solution several times, but still could not get the problem fixed. I guess I am just resolved to going back to the WM6 ROM. Thanks for the info though.
@abhijitray: I already tried changing the power settings when I first began having problems, so that's not it.
i have the same problem with my Tilt. But i found that when i connect to my PC with the USB cable, ActiveSync is on, my IE works fine. With Wifi connection, IE is still dead.
maybe an off topic question, but what does the new rom have that the original rom that came with the tilt doesn't? anyone have a link or something, or is it something like better batter performance? thx
i have tilt with the latest official WM6.1 ROM, and have no issues with Wifi.
Ok - here's my story.
I had a default WM 6.0 Official ROM Tilt and upgraded to ATT's 6.1. Immediately my WiFi stopped working. I waited for updates on this thread, and with my temper rising at such a poor release, I decided to go to Dutty's 6.1 Hybrid. Same thing - Wi-Fi didn't work. (To qualify, it would connect and get an IP address, but any attempt to access the net - ping, ftp, Gmaps, Activesync - would fail) I upgraded to the latest eMo radio and still didn't work. I scratched my head and decided to check my router. It's an older D-Link 802.11b and sadly the last firmware was released in 2005. I changed the settings on it to not use Turbo mode and voila, it connected. All happy and such.
But now the problem is slightly different. It will connect once, but after it disconnects (either because I manually turned off WiFi on the phone or the phone entered Standby mode) I cannot connect again. I literally have to reboot my router. This is great a home, but I worry when I have to use a public wifi hotspot. Any thoughts on that?
And yes, I have played around with the power settings.
Kojak
another thing I have noticed on my router is that my Tilt is not sending a hostname along with the DHCP request. Could that be the issue on the WiFi connection? I am wondering if that confuses the router.
Tom
I have the same problem too. tytn II with latest rom. At home with my old linksys which is a 802.11b device. If i disconnect wifi and then try to connect - the phone say - Unavailable. I notice that if i change the channel the phone connect just fine.... very strange
ps. sorry for my bad eng.
pasole said:
I have the same problem too. tytn II with latest rom. At home with my old linksys which is a 802.11b device. If i disconnect wifi and then try to connect - the phone say - Unavailable. I notice that if i change the channel the phone connect just fine.... very strange
ps. sorry for my bad eng.
Click to expand...
Click to collapse
I see the same here - I think that by changing the channel it reboots/resets the router and allows you to try again.
ps. don't worry about your english. If this board was in a different language, I am sure that most people here would not even be able to post a thing.
kojak_nyc said:
Ok - here's my story.
I had a default WM 6.0 Official ROM Tilt and upgraded to ATT's 6.1. Immediately my WiFi stopped working. I waited for updates on this thread, and with my temper rising at such a poor release, I decided to go to Dutty's 6.1 Hybrid. Same thing - Wi-Fi didn't work. (To qualify, it would connect and get an IP address, but any attempt to access the net - ping, ftp, Gmaps, Activesync - would fail) I upgraded to the latest eMo radio and still didn't work. I scratched my head and decided to check my router. It's an older D-Link 802.11b and sadly the last firmware was released in 2005. I changed the settings on it to not use Turbo mode and voila, it connected. All happy and such.
But now the problem is slightly different. It will connect once, but after it disconnects (either because I manually turned off WiFi on the phone or the phone entered Standby mode) I cannot connect again. I literally have to reboot my router. This is great a home, but I worry when I have to use a public wifi hotspot. Any thoughts on that?
And yes, I have played around with the power settings.
Kojak
Click to expand...
Click to collapse
Well, your problem sounds exactly the same as mine (WM6.1 official). Maybe I should have tried a public hotspot, but it just wouldn't work on my home network (I even cut off the encryption and made it open). I downgraded back to WM6 ROM and everything working fine, so I guess no WM6.1 for me.
It is definite a router by router problem. Had problems with the D-Link but I tried it on a Buffalo 802.11g router running Tomato firmware, and I had absolutely no problems. That being said, this could be either a:
802.11b problem?
D-Link problem?
Something must have changed in the WM 6.1 code from WM6.0 as it pertains to WiFi. If only it was as easy as a toggle setting to fix.
For me, it was the opposite. I could get WiFi to work at my office on Mobile 6.0, but I couldn't get my network at home to work. I have a Wireless-N network at home, and even though I set it to B-G only mode, it still wouldn't connect. As soon as I hit WM6.1, everything was fine.
Unfortunately, this happens more than one would think with Wireless network equipment.
kojak_nyc said:
It is definite a router by router problem. Had problems with the D-Link but I tried it on a Buffalo 802.11g router running Tomato firmware, and I had absolutely no problems. That being said, this could be either a:
802.11b problem?
D-Link problem?
Something must have changed in the WM 6.1 code from WM6.0 as it pertains to WiFi. If only it was as easy as a toggle setting to fix.
Click to expand...
Click to collapse
Kojak_nyc,
You hit it on the head. It is a router issue, although its not limited to the D-Link router because I have a 2wire HomePortal 1000HW and it also doesn't work. It is also on 802.11b, so that could also be the issue. Something must have changed between in the settings the WM6 and the WM6.1 upgrade. I'll go ahead an inform HTC of the issue (not that they'll do anything).
I believe that the once the tilt is updated to WM6.1, it no longer works on IEEE 802.11b.
I think this is a Dlink issue. I've got a linksys router at home and it connects to that fairly quickly. ssid on that isn't hidden cuz i've got vista machines that have a hard time connecting.
anyway, at work i've got a dlink di624, 802.11g, router and i've not been able to connect the kaiser to it. i think tomorrow i'll do what was suggested and just play around with the channels and find which works. the dlink's set to automatically choose the channel it uses so i'll hard code it for a channel i know the kaiser'll scan for and then see what happens.
if it doesn't work i'll juts keep using the 3g connection... i do have 6GB/mo and haven't come anywhere near using it up.
Experienced similar problem just now. I just upgraded to WM 6.1 and my WiFi connection's been unstable since last night. I have a wireless router with excellent signal on my room and enjoys streaming video before I upgraded to WM 6.1. When I reset the phone it restored WiFi connection again.
Hope you could share some tweaks to resolve this problem.
Thanks.

WiFi unable to connect to router after 6.1

I've been running 6.1 ROM (Official) now for a month or so and am using a program on my Tilt that uses a lot of data...so while I'm at home I thought I would allow it to use my WiFi router instead of my 3G connection.
I turned on the WiFi and it can "see" my router's SSID. I enter the WPA-TKIP passcode and tell it to connect. It just sits there saying "connecting to network" but never completes the connection to acquire it's IP.
I have even gone as far as setting the IP configuration manually (Static IP) and the TILT keeps trying to connect to the network.
I have a DLink DI-624 that I have had no problems connecting the WiFi when I was running ROM 6.0.
I have done the following in trying to troubleshoot:
- Turned OFF Turbo on the Router
- Configured router for AutoChannel
- Configured TILT for Best Performance
- Rebooted Router AND TILT.
Still no go...Ideas?
I sometimes get this after flashing a new rom. It seems to affect the way it connects to WPA networks but not WEP or unsecured.
You can try changing your security to WEP and see if that works.
But when I need to solve this I usually have to do a Hard Reset and then connect the WIFI first. When it does this the phone seems to be able to auto-detect the network type (i.e without me needing to select it as WPA) and after entering the passcode it can connect.
Yep, go to WEP, this should be enough for most people and has never given me a problem.
martythebrit said:
Yep, go to WEP, this should be enough for most people and has never given me a problem.
Click to expand...
Click to collapse
Unfortunately I can't change my network to WEP. My network is not only my home network but also used for my wife's business...so for security reasons I have to keep the security up.
Drop the security just for a test and see what happens.
I am using the official ATT 6.1 ROM and it works just fine on my wifi, first with WPA-PSK then with WPA2-PSK. You could set your WAP to WEP (say that fast 3 times!) for a 5 minute test and see if it connects. Does your phone connect to other Wifi hot spots? What does ministumbler say about wifi in your area? You may have some interference with a neighbors wifi.
Well...I know that my issue is not limited to my router at home (DLink DI-624). I'm experiencing the SAME issues at work as well.
At work I'm using a NetGear WGT624 v3.
- The security is WPA-PSK (TKIP)...just like at home.
- Broadcasting SSID on Channel 11 (Fixed). There are no routers in nearby offices (I've checked using a wifi scanner on my laptop).
- I've configured a static IP in my Tilt and it just sits there at Connecting...again same as what happens at my house.
- I have also tried using DHCP with no joy.
I'll try the WEP at home to see if it's a WEP/WPA issue.
Unfortunately if it IS an issue...I don't think I'm going to get much joy from HTC on releasing a fix. Maybe there will be some way around it though...I hope!
Make sure you use the correct authentication: Use Smart Card or Certificate. That fixed mine
brynwall said:
Make sure you use the correct authentication: Use Smart Card or Certificate. That fixed mine
Click to expand...
Click to collapse
Here is what I have set in my TILT...
Connects to: The Internet
Hidden network: NOT checked
Ad-Hoc: Unselectable (Grey)
Auth: WPA-PSK
Encry: TKIP
Use IEEE: Grey (Non-Selectable)
EAP: Grey (Non-Selectable...but Smartcard or Certificate IS in the box)
(Still at work...will test WEP when I get home)
(I'm home)
Ok...Now I know for SURE that this is a WPA issue with the TILT running the AT&T ROM 6.1 (Official).
I changed my home router from WPA-PSK (TKIP) to WEP.
Made the needed changes in my TILT to change it from WPA to WEP and entered the correct key.
* IT CONNECTED TO THE ROUTER! Whoo Hoo.
I change nothing in the router except from WEP back to WPA and again I'm stuck at "connecting" on the TILT.
Ideas?
At least you know
And Knowing Is Half The Battle
clstan said:
(I'm home)
Ok...Now I know for SURE that this is a WPA issue with the TILT running the AT&T ROM 6.1 (Official).
I changed my home router from WPA-PSK (TKIP) to WEP.
Made the needed changes in my TILT to change it from WPA to WEP and entered the correct key.
* IT CONNECTED TO THE ROUTER! Whoo Hoo.
I change nothing in the router except from WEP back to WPA and again I'm stuck at "connecting" on the TILT.
Ideas?
Click to expand...
Click to collapse
Is a backing up everything and doing a hard reset too much hassle? Make sure you connect to a WPA Wifi first before installing any other programs. Its the only way I could fix it... =/ As recommended I always do another hard reset straight after flashing a new rom now.
Hey...someone...somewhere has mentioned that there might be a WPA issue in relation to removing the AT&T Bloat. Is there anything to this? I HAVE removed my bloat on my Tilt.
I don't want to have to re-Hard my Tilt...but will if I have to...but only as last resort.
What fixed with my DI-624
I found that I had to upgrade to the newest ROM from D-Link. (I had original ROM from 5 years ago.) I found that the PSK password (using WPA2) could NOT contains shift-numbers such as $, %, #. I converted the symbols to numbers (and letters)and it works fine now. I have had no problems since.
segaza said:
I found that I had to upgrade to the newest ROM from D-Link. (I had original ROM from 5 years ago.) I found that the PSK password (using WPA2) could NOT contains shift-numbers such as $, %, #. I converted the symbols to numbers (and letters)and it works fine now. I have had no problems since.
Click to expand...
Click to collapse
My home router is a DI-624 Rev E. The ONLY Firmware for the E Rev is 5.00 and I'm running it.
Even though not completely secure...my WPA password is a 20 character, lower case entry...no strange characters or whatever.
*Well folks...I had just installed the 6.1 Rom onto my Tilt about a month ago...so I don't have that much installed...and I can always reload it. So I HardReset and followed by removing bloat. WPA WORKS NOW! (Insert "Twilight Zone" theme music here.)
All in all...it just seems strange to have to HARD Reset my phone to get something like this to work again.

Wifi problems

I am unable to get Wifi to connect to any network! The device shows me the available network and everything, but it says it's connecting to them and then it just says they're available. It was working fine for 2 weeks on this rom Ultimate-X2.V9 and just stopped yesterday. Its a Kaiser
Any solutions? Suggestions?
if they are not your wifi router networks they could have added mac filtering to keep you out
otherwise maybe their firmware require an update or they just need a restart all the connects handheld devices make often confuse the dhcp in the router
I've got the same problem, but they are my networks, and they've all been restarted.
One network especially doesn't have mac filtering applied, but has SSID hidden, which is fine, but it still won't connect.
I have been dicking about with changing Roms recently, but am back on the stock HTC rom, so wondering if something could've messed up the Wifi abilities.
Thanks,
Hi,
I have the same problem on my kaiser, with every rom I've tried.
On a previous rom, I found a reg key which prevented wifi to connect, and it resolved the problem, but now I can't remember what the key is...
Wifi APs are detected, identification is sent, PPC asks for the wep/wpa key, identification seems to succeed, sometimes I even get the right IP, but nothing happens, and the PPC stops the connection to the AP after a few seconds...
Very annoying
I should add, all routers in use are fully up-to-date with their firmwares, and recently I've been receiving a message saying "Shell32.exe" issue.
I get the option to send the report to M$, however the ironic problem with that is I need the network to use it!
I've just flashed my phone back to the original Orange ROM, so I'll see how that goes now, but when I did manage to connect to my home network, it would connect, allow me to even refresh my IP, but not allow me to access any websites, use any installed applications etc.
same problem
but it happend after i installed moorhunn.
Little better after i uninstalled it but my kaiser still drop the connection in a few seconds and want to turn on the 3g connection instead...
I getting an error message that says"no active programs is started".

Categories

Resources