When I turn on my phone at work, the wireless connection (open unsecured) connects and works for a few minutes. After some time, it disconnects and without rebooting my phone, I cannot establish a wlan connection.
This is oly the case at work. At home it works flawlessly, but it is another network kind.
Anyone found a solution to this problem? I saw a lot of threads about this but no good answers.
I am using duttys v3.
Not sure. Perhaps there is some sort of time out on your work network for inactive devices, or dhcp ip releases or something weird and "networky" like that?
Or perhaps your phone is going into a power save mode if you are not using it?
Just general ideas, I don't have this particular problem
I dont think many people have this issue! you must not have a setting correct, try downloading KaiserTweak and adjusting the timeout and also take a look at the routers settings I find it strange that a business would have an open network for security issues
austinsnyc said:
I dont think many people have this issue! you must not have a setting correct, try downloading KaiserTweak and adjusting the timeout and also take a look at the routers settings I find it strange that a business would have an open network for security issues
Click to expand...
Click to collapse
I work at the university, and the network is unsecure. You have to enter login and pass at a webpage to gain access.
I cannot reconnect at all once ive been disconnected. So it should have anything to do with kaisertweak or timeouts.
I have tried every setting and combination. I have tried to select work/internet settings. Ive tried to tell the phone its a hidden network / not hidden network. I have tried to use power save / performance mode. Ive tried to turn off 3g, bluetooth, phone (everything basically).
When I tap connect, it says connecting and then it immediately goes to "active" and tries to connect to another network (which I dont have access to).
solwretep said:
When I turn on my phone at work, the wireless connection (open unsecured) connects and works for a few minutes. After some time, it disconnects and without rebooting my phone, I cannot establish a wlan connection.
This is oly the case at work. At home it works flawlessly, but it is another network kind.
Anyone found a solution to this problem? I saw a lot of threads about this but no good answers.
I am using duttys v3.
Click to expand...
Click to collapse
I have worked out the problem.. first if its a WPA enterprise connection, make sure its set to WORK and not INTERNET setting. it will work. my only works with schaps versions not duttys
on my old pda (Acer N50 premium) I had the same problem with my unis network... it would only work (if at all) for a few minutes then nada... but at home it was absolutely fine, quick stayed on and totally responsive... I wonder if it has something to do with the rubbish way unis run their IT...?
Wasted thread
Many do not have this issue.
According to what's being said here by the indiviuals with issues, you're having problems connecting to a certain network...not all networks.
If it were all networks; your device, settings, equipment or rom would be the common denomenator. Since it's one network, it's that network.
Just because a network is or appears to be available, that doesn't mean that you can connect to it.
dwny said:
Wasted thread
Many do not have this issue.
According to what's being said here by the indiviuals with issues, you're having problems connecting to a certain network...not all networks.
If it were all networks; your device, settings, equipment or rom would be the common denomenator. Since it's one network, it's that network.
Just because a network is or appears to be available, that doesn't mean that you can connect to it.
Click to expand...
Click to collapse
no, it could be the phone software. Lets says that a string is added to the registry if the network you are connected to disconnects you; a string that makes the phone cancel connections to the network. And lets assume that the network disconnected you because there is a hidden firewall in the phone software that blocks ping requests, thus making the network believe that the connection is lost and thus disconnecting you. Then we have a moment 22, which is basically something wrong with the phone.
As some readers already pointed out in this "wasted thread", when changing the rom (in one case) or when changing settings from "internet" to "work" (in the second case) there is a great possibility that this problem in fact has to do with phone software and not network.
In my case, it just happens to be neither of the mentioned solutions or any solution that I have found in other threads.
One thing you may want to check is that your wifi is set to max performance. The issue may also be that there is a DNS cache issue, in most cases it can be resolved by manually reconfiguring the connection.
I have been successful in configuring my phone's WLAN to connect to everything from open APS's, WEP, WPA, RADIUS and AP's with proxy redirects, so I can tell you that as with most cases, it's human error.
I have tried max performance.
How do I resolve a dns cache issue? Manually reconfiguring the network did not help (only thing that helps is a reboot).
seattleweb said:
One thing you may want to check is that your wifi is set to max performance. The issue may also be that there is a DNS cache issue, in most cases it can be resolved by manually reconfiguring the connection.
I have been successful in configuring my phone's WLAN to connect to everything from open APS's, WEP, WPA, RADIUS and AP's with proxy redirects, so I can tell you that as with most cases, it's human error.
Click to expand...
Click to collapse
Related
Hello Everyone,
I'm looking for either a confirmation that my my WLAN is bad, or suggestions on other things I should try before taking it back in for replacement.
Searching and browsing through the forums I didn't see anyone mention any of the problems I'm having so I'm assuming I'm the only one (or one of very few) that bought a Kaiser with a defective Wifi radio.
Here's the symptoms:
I tried connecting to my wireless connection at home maybe a day or two after I bought my Tilt (last Friday). My home connection is draft 802.11n with WPA2-PSK security.
So I enable the WLAN and it detects my Wifi network and it asks for the key. I input it and then it tries to connect, but... it never does. I tried it a few times consecutively and it still didn't work (I get the animating arrows and the 'halo' around the beacon, but then it goes away, and it just keeps doing that). Now, I've seen this before with on my XV6700 with a beta ROM of WM6, but I know well HTC and AT&T wouldn't release something with broken WPA/2 support. At least HTC, I thought...
So I unlocked my Tilt and loaded the factory Kaiser ROM I downloaded from here, and well, WPA2 didn't work on it either. Weird, I thought, so I searched forums and no one mentioned any of this. So I changed my security settings on my network to WPA-PSK (from WPA2) and that made no difference at all... I don't want to bore y'all with everything else I tried, but to sum it up, I then tried a WPA fix I found on PPCGeeks, but that just ended up making my WLAN staying disabled, so I unintalled that and I decided I would try it with a WEP or Open wireless network.
Well, this morning I did just that and even when I try to connect to a wireless connection with WEP, I get the same behavior when I tried this at home with WPA. I've triple checked the WEP key, and I know it's right.
I haven't tried it on an Open network yet, but I'm assuming I'm going to get the same results. I'll have to find a wireless router no one's connected to so that I can try this out, but it might take me a while. Should I even waste anymore time on this? Anyone else here having (or had) the same problem?
I might start loading the AT&T ROM on this soon so I can take it back, but if any of you have any suggestions, I'm all ears.
Wow. Am I the only one on here who's having this problem?? Lucky me, I guess... :S
Anyway, I just tried connecting to a public and open wifi network here in SF, but my Kaiser still wouldn't connect. Guess that confirms it: my WiFi adapter is defective.
Anyone know if I can get it replaced in a different store from where I purchased it, and what I need to take (hope it's just the phone)?
d0ubl3_d1zzl3 said:
Wow. Am I the only one on here who's having this problem?? Lucky me, I guess... :S
Anyway, I just tried connecting to a public and open wifi network here in SF, but my Kaiser still wouldn't connect. Guess that confirms it: my WiFi adapter is defective.
Anyone know if I can get it replaced in a different store from where I purchased it, and what I need to take (hope it's just the phone)?
Click to expand...
Click to collapse
just tried my wifi on the tilt ... works fine out of the box (to my home secured wireless network)
d0ubl3_d1zzl3 said:
Hello Everyone,
I'm looking for either a confirmation that my my WLAN is bad, or suggestions on other things I should try before taking it back in for replacement.
Searching and browsing through the forums I didn't see anyone mention any of the problems I'm having so I'm assuming I'm the only one (or one of very few) that bought a Kaiser with a defective Wifi radio.
Here's the symptoms:
I tried connecting to my wireless connection at home maybe a day or two after I bought my Tilt (last Friday). My home connection is draft 802.11n with WPA2-PSK security.
So I enable the WLAN and it detects my Wifi network and it asks for the key. I input it and then it tries to connect, but... it never does. I tried it a few times consecutively and it still didn't work (I get the animating arrows and the 'halo' around the beacon, but then it goes away, and it just keeps doing that). Now, I've seen this before with on my XV6700 with a beta ROM of WM6, but I know well HTC and AT&T wouldn't release something with broken WPA/2 support. At least HTC, I thought...
So I unlocked my Tilt and loaded the factory Kaiser ROM I downloaded from here, and well, WPA2 didn't work on it either. Weird, I thought, so I searched forums and no one mentioned any of this. So I changed my security settings on my network to WPA-PSK (from WPA2) and that made no difference at all... I don't want to bore y'all with everything else I tried, but to sum it up, I then tried a WPA fix I found on PPCGeeks, but that just ended up making my WLAN staying disabled, so I unintalled that and I decided I would try it with a WEP or Open wireless network.
Well, this morning I did just that and even when I try to connect to a wireless connection with WEP, I get the same behavior when I tried this at home with WPA. I've triple checked the WEP key, and I know it's right.
I haven't tried it on an Open network yet, but I'm assuming I'm going to get the same results. I'll have to find a wireless router no one's connected to so that I can try this out, but it might take me a while. Should I even waste anymore time on this? Anyone else here having (or had) the same problem?
I might start loading the AT&T ROM on this soon so I can take it back, but if any of you have any suggestions, I'm all ears.
Click to expand...
Click to collapse
This is what I did. Start->settings->connections tab->WiFI. Now you should see your routers name there with the signal bar next to it. Tap AND Hold the name, then go to settings or edit(I forget), then click NEXT, uncheck the box that says "the key is automatically provided"(thats for open access routers/networks that dont require codes). Then type in your code & make sure you specify what key # it is. click next and youre done. You should be able to connect.
silly question here. is your router broadcasting 802.11b or g? the wifi won't connect to anything else.
You might also check your AP to see if it's not broadcasting its SSID to the world (a common security setting). I couldn't connect until I enabled broadcast on my AP, set the network up, and then went back and disabled SSID broadcast.
Why in the hell this is a problem in the first place is beyond me, but this is the third smartphone/PDA with wireless that I've had to do that for. And every time, once the device found the network once, it never had a problem finding it again.
Believe me. I tried everything in the WiFi settings page. I edited the settings, removed them and added them again, and like I said before I even went and changed my security settings on my router (which to answer your question, zeta, it broadcasts in: n, g, and b. Same router worked with my Apache/XV6700).
Anyway, I stopped by the store where I bought it today and they told me that as far as he can tell, that does qualify for a replacement. The problem is they don't have any in stock to replace it with, and he has no idea when they'll be getting more in. They only received 2 on launch day, and I bought one of those. He did mention that I can get it replaced at any store, however, but they all might be in the same boat.
Guess I'll try another store tomorrow, but if not I guess I'll have to go through AT&T's tech support (don't like the sound of that) and get it replaced through them. So I guess this means I might have a few days to mess around with the phone and even try some risky thangs.
So if any of you developers and hackers, er, I mean tweakers need some1 to test something, I can be that guinea pig (for a while at least)... Just give me a shout.
To troubleshoot your wireless connection always try ruling out as many other factors as possible. So put your router to NO security (temporarily ofcourse) and have it broadcast 802.11g. Also make sure you add the mac address of your device to the list in your router, if it uses mac address filtering. Try connecting to it with a laptop and see if that goes fine. Work systematically...
PerfAlbion said:
You might also check your AP to see if it's not broadcasting its SSID to the world (a common security setting). I couldn't connect until I enabled broadcast on my AP, set the network up, and then went back and disabled SSID broadcast.
Why in the hell this is a problem in the first place is beyond me, but this is the third smartphone/PDA with wireless that I've had to do that for. And every time, once the device found the network once, it never had a problem finding it again.
Click to expand...
Click to collapse
I have a similar Problem, your solution works partly for me:
As soon as I enable the AP to broadcast it's ID, Kaiser connects.
But as soon as the ID is hidden, it does not connect.
Weird.
Is it a security problem if the ID is broadcasted, provided I use WPA2-PSK/AES?
Thanks
V
No. Hiding the SSID really only protects you from folks that are wandering around without any tools. Open up a more fully featured scanner, and it'll pull the SSID out of the air. The encryption is much, much more important.
And I also wouldn't bother with MAC filtering. Changing the MAC address is usually a software setting, so it's not all that much additional security. WPA/WPA2 are much better solutions.
Yeah, the hidden SSID is not an issue with me, since I don't mind broadcasting it at home. Not too paranoid about it. If someone *really* wanted to sniff and break into my network, they could. Don't do much important and highly confidential stuff at home anyway.
Plus, like Perf mentioned, there's software out there, even for PocketPCs, that will find so-called "hidden" SSIDs. Thanks for your suggestions, anyway.
d0ubl3_d1zzl3 said:
Yeah, the hidden SSID is not an issue with me, since I don't mind broadcasting it at home. Not too paranoid about it. If someone *really* wanted to sniff and break into my network, they could. Don't do much important and highly confidential stuff at home anyway.
Plus, like Perf mentioned, there's software out there, even for PocketPCs, that will find so-called "hidden" SSIDs. Thanks for your suggestions, anyway.
Click to expand...
Click to collapse
i had no issue connecting to my wrt54g running DD-WRT v23 SP2 with my SSID hidden with WEP enabled. when setting up a new connection, i just entered the name of the connection and then the WEP hex, and it connected flawlessly. Have fun hacking your phone until you can swap?
Mine is not working either. I exchanged the phone and found out that I was the 3rd person with the same problem.
BiPolarXpress said:
Mine is not working either. I exchanged the phone and found out that I was the 3rd person with the same problem.
Click to expand...
Click to collapse
Glad to hear, I'm not the only one.
I exchanged my phone this morning, and I just tried connecting to my wireless network and guess what??
I'm getting the SAME RESULTS.
Now, before anyone goes and tells me that my router is the problem or that it's user error, then tell me: why does my laptop, PS3 and my Wii connect just fine?? I even changed the SSID and WPA key last night and they all connected w/o a problem as well. All except my freaking Tilt.
Can be it a coincidence that I got 2 bad phones? I don't know if I should call the store and tell them to hold up on sending the other phone to HTC.
Which reminds me, I probably should try calling HTC today, but I doubt they'll be much help...
I don't think you're nuts, and I doubt you got two bad phones. But if you want to double-check, take the phone to your local Starbucks or other shop with WiFi and see if it can detect that AP.
But at this point, I'd be inclined to look for a firmware upgrade for your AP. I could be that it's not supporting long or short preambles right (a problem for some devices in the past), doesn't like seeing more than XXX different devices, or just doesn't like your phone much.
Either way, I'm smelling an issue with your AP. I had a US Robotics AP/Router that drove me nuts because it would spontaneously reboot after a random period any time an IPSec VPN was present.
try setting the power mode on best performance. when i do that i stay connected to wifi.
I took both my old I730 and my tilt to the coffee shop before I returned my first tilt. I was able to connect my I730 at the coffee shop and home, but couldn't connect the tilt at either place. I also tried some open AP's in my neighborhood that I have been able to connect to in the past with the same results. Picky phone or bad wifi radios maybe.
Jesus... like the bloke said:
1) Turn off wpa and see if it will connect (it will unless you have set your N router to only use "n") If it won't then send it back.
2) If it does... then turn on WEP 128bit on your router... and use that instead.
WM devices have always had problems with WPA...
Hi all.
I have tried my HTC TyTN II with one Wifi LinkSys WAG54GS Router using WPA and not hidding the SSID and works fine, no problem at all.
Test with one AP from DLink at the office, using hidden SSID and WEP 64 and 128 Bits and no problem at all, works as fine as my LinkSys.
I'm going to try hidde the SSID at home with WPA and WPA2 and post the results later to know if there is a common issue with Kaiser or some freaky coincidence.
Regards.
d0ubl3_d1zzl3 said:
Hello Everyone,
I'm looking for either a confirmation that my my WLAN is bad, or suggestions on other things I should try before taking it back in for replacement.
Searching and browsing through the forums I didn't see anyone mention any of the problems I'm having so I'm assuming I'm the only one (or one of very few) that bought a Kaiser with a defective Wifi radio.
Here's the symptoms:
I tried connecting to my wireless connection at home maybe a day or two after I bought my Tilt (last Friday). My home connection is draft 802.11n with WPA2-PSK security.
So I enable the WLAN and it detects my Wifi network and it asks for the key. I input it and then it tries to connect, but... it never does. I tried it a few times consecutively and it still didn't work (I get the animating arrows and the 'halo' around the beacon, but then it goes away, and it just keeps doing that). Now, I've seen this before with on my XV6700 with a beta ROM of WM6, but I know well HTC and AT&T wouldn't release something with broken WPA/2 support. At least HTC, I thought...
So I unlocked my Tilt and loaded the factory Kaiser ROM I downloaded from here, and well, WPA2 didn't work on it either. Weird, I thought, so I searched forums and no one mentioned any of this. So I changed my security settings on my network to WPA-PSK (from WPA2) and that made no difference at all... I don't want to bore y'all with everything else I tried, but to sum it up, I then tried a WPA fix I found on PPCGeeks, but that just ended up making my WLAN staying disabled, so I unintalled that and I decided I would try it with a WEP or Open wireless network.
Well, this morning I did just that and even when I try to connect to a wireless connection with WEP, I get the same behavior when I tried this at home with WPA. I've triple checked the WEP key, and I know it's right.
I haven't tried it on an Open network yet, but I'm assuming I'm going to get the same results. I'll have to find a wireless router no one's connected to so that I can try this out, but it might take me a while. Should I even waste anymore time on this? Anyone else here having (or had) the same problem?
I might start loading the AT&T ROM on this soon so I can take it back, but if any of you have any suggestions, I'm all ears.
Click to expand...
Click to collapse
I found that I couldn't get my Kaiser to connect to my WPA encrypted LAN - open access and WEP (64 and 128 bit) work fine.
Not sure what the problem is - maybe some incompatibility between the Kaiser and my Netgear router. I've downgraded the security to 128bit WEP for the time being but I'm hoping that there's a fix soon.
Hi.
I recently bought my s730. Quite pleased with it, but one thing bothers me.
When i connect to my wlan at home (zyxel_2602hw_d1a WPA-PSK TKIP) i'm able to connect to the router, but I don't seem to be able to get an connection to anywhere outside my own network. I tried using Live Messenger, IE, Opera and Skype, but nothing happens.
When I'm using GPRS or EDGE it all works smoothly.
Any suggestions?
Do you have your connection set to automatic or only through your phone network? I have seen a few problems with that.
Also, double check that you are entering wep or any other security protocol correctly, took my 6 tries before it would work, it looked like it was connected to the network but it really wasnt (just personal experience with this phone.)
10332007 said:
Do you have your connection set to automatic or only through your phone network? I have seen a few problems with that.
Also, double check that you are entering wep or any other security protocol correctly, took my 6 tries before it would work, it looked like it was connected to the network but it really wasnt (just personal experience with this phone.)
Click to expand...
Click to collapse
I do have the connection settings in both IE and Opera set to automatic. I's there somewhere else I have to change settings?
I'm quite sure i typed the password correctly. I also checked the client list on the router and the phone showed up correctly.
Gah, cant remember where I saw it but there was a setting in the phone itself for what to connect to.
Another thing to try under the wifi connection open your saved connection and go into it and see if you have it set to connect to the internet or just to the private network under "network type" in the Wi-Fi sub menu of Wlan settings. Its late and I cant think right, i'll see about checking more into it later...
I solved this problem - change your WLAN security on your WLAN router only on exactly MAC adressee (no any WEP) and your Wings is allowed to connect and all will be OK, work OK - Skype, IE, Opera. Problem was only to find MAC adressee my Wings
Wing + WRT54GL
Hi!
I have an S730 and a Linksys WRT54GL router. I've tried to use wlan with my phone, but it doesn't working. I want to use WPA2 with AES without Radius. Is the WPA shared key (router) same to network key(phone)? without security and encryption, it's working well.. I cannot see any syslog. That could be so easy..
klenovcok said:
I solved this problem - change your WLAN security on your WLAN router only on exactly MAC adressee (no any WEP) and your Wings is allowed to connect and all will be OK, work OK - Skype, IE, Opera. Problem was only to find MAC adressee my Wings
Click to expand...
Click to collapse
I tried removing security for my phone MAC address, but there dosn't seem to be any options on my router allowing this. So I'm still stuck;-/
ksga said:
Hi.
I recently bought my s730. Quite pleased with it, but one thing bothers me.
When i connect to my wlan at home (zyxel_2602hw_d1a WPA-PSK TKIP) i'm able to connect to the router, but I don't seem to be able to get an connection to anywhere outside my own network. I tried using Live Messenger, IE, Opera and Skype, but nothing happens.
When I'm using GPRS or EDGE it all works smoothly.
Any suggestions?
Click to expand...
Click to collapse
Did you check network settings? I mean e.g. if you don't use DHCP server and you didn't fill in right settings phone may connect to network but may not get outside. I know it can look like "lame" question, but sometimes even a master can do a newbie mistake..
ksga said:
I tried removing security for my phone MAC address, but there dosn't seem to be any options on my router allowing this. So I'm still stuck;-/
Click to expand...
Click to collapse
usually it is in section WLAN Advanced setup - WEP Encryption - disable and in WLAN MAC Filters - active + allow asotiation with table of adress your Wings - aply . I have Zyxel Prestige 660HW.
I'm sure that DHCP is active, and that I get an IP.
I tried disabling security on my router, but same problem. Connects to my router, gets an IP but still nothing works
ksga said:
I'm sure that DHCP is active, and that I get an IP.
I tried disabling security on my router, but same problem. Connects to my router, gets an IP but still nothing works
Click to expand...
Click to collapse
Your DNS are also provided automatically? Or could you ping (through some app) to any IP address of any server on the internet? If you succee, then we can look for a mistake with DNS.
Problem solved!!!
Okay. Found the cause for all my sufferings...
Power management. under WLAN-settings i changed power setting from power save mode to best performance...
thanks for all the help. hope next time I have a better question
wifi problem
hello everybody,i have tried several times to connect to my router at home but no chance at the end i got this warning saying:
cannot log on to the wireless network this network requires a personel certificate to positively identify you.
Hey guys, i got my kaiser a couple of days ago. Its a brilliant machine and i love using internet on it using my wifi connection at home. Suddenly it has stopped browsing the internet. It connects to wifi alright, show good strength signal and everything but when i enter a web address it takes ages to respond and in the end gives the error 'check name and try again.' what's wrong with it...?
i'd appreciate if some could help.
P.S. i have done countless soft resets and a hard reset as well.
cheers
I've had problems like that before. By any chance is your router named something like Linksys or default? I'm wondering if it's connecting but not using the correct profile. I'm not sure about the phones but on a computer you can connect to wifi that is wep enabled without a wep key. You can't get any data from the router but it shows your connected.
Also have you tried another access point to rule out your router?
Don't you have to go to wifi settings and change it from BEST PERFORMANCE to BEST BATTERY or is it the other way around?
ChumleyEX said:
I've had problems like that before. By any chance is your router named something like Linksys or default? I'm wondering if it's connecting but not using the correct profile. I'm not sure about the phones but on a computer you can connect to wifi that is wep enabled without a wep key. You can't get any data from the router but it shows your connected.
Also have you tried another access point to rule out your router?
Click to expand...
Click to collapse
No, i haven't tried any other AP, its my home network and i have only one router. Its quite an old one but i am sure its not from linksys. Last time i successfuly used wifi internet on my kaiser was a few hours ago before i installed a remote desktop access program on my kaiser. I have uninstalled it now but the problem remains.
The phone might have profiles based on the name of the router, so if you have a common name and it picks another one up of that name, it could cause this sort of problem.
ChumleyEX said:
The phone might have profiles based on the name of the router, so if you have a common name and it picks another one up of that name, it could cause this sort of problem.
Click to expand...
Click to collapse
So what do i need to change, the name of the router or the profile on the kaiser, by the way , where is the profile on the pocket pc ?
P.S. its Belkin and the called WLAN.
go into the com manager and hit settings, then wireless lan. You might want to look around in there to see if you can remove the profile.
RESOLVED
ChumleyEX said:
go into the com manager and hit settings, then wireless lan. You might want to look around in there to see if you can remove the profile.
Click to expand...
Click to collapse
Hi again, you wouldn't believe what i am about to tell you. The problem gets solved like magic just with a couple of clicks. In your power settings for the wireless network, change it from best battery life to best performance and voila! it starts working. The moment you change it back to best battery life, it dies out. I have tested it time and again and use another utility called 'vxutil' to use different commands like ping and see information like default gateways and DNS and DHCP but everything was alright.
P.S. this will only work if the network settings are correct ALREADY!
Thanks for the help guys!
Hi guys!
I have a Touch Diamond 2. It's great and certainly an upgrade from my Touch Cruise!
I have a strange problem though. Whenever I try to connect through 3G (T-Mobile Netherlands), immediatly after it makes the connection, it gives the dialog 'cannot connect etc'. 3G is truly connected but no data is coming in.
Now I have found where the problem lies, sort of. 3G works fine when I don't configure my home Wifi connection. Whenever I configure that, 3G stops working. It doesn't matter if Wifi is turned on or off. 3G does have a dynamic ip, where my Wifi connection requires a static IP. But I make all these settings in the Wifi part of the configuration screen, the IP details are under the 802.11 b/g network card.
This used to work flawlessy on my Cruise. Anyone have a solution? Thanks!
good morning. as you are with tmobile i'd suggest you are having the same problems as me with tmobile uk. for some reason tmobile sets up a proxy server in your 3g data connection setup, this caused huge problems for me but clearing it solved them all.
try this first and see how you go.
Possible, but where exactly do I change the proxy settings of the 3G connection?
BeQuietAndDrive said:
Possible, but where exactly do I change the proxy settings of the 3G connection?
Click to expand...
Click to collapse
Hey that's a coincidence, just read the same question at GoT
I have similar problems.
Now and than my HSDPA connection works good, but at some moment I just can't reach any website.
Disconnecting and reconnecting to HSDPA sometimes helps, and sometimes I just have to wait a few minutes and than it works again.
I also tried another DNS (OpenDNS) but it doesn't solve the problem,
Proxy settings can be found at (I assume your dutch):
Instellingen> Meer> Verbindingen> Verbindingen> Mijn proxyserver instellen
At my TD2 is no proxy set, so thats not the cause.
Hope sombody else can help!
Do you have a static IP for WIFI as well? I kinda found out that setting WIFI on dynamic IP solves the 3G problem, so somehow they must be connected. But this should be able to work, it's almost as if 3G 'takes over' the static IP from the WIFI settings, but the connection settings from my 3G are offcourse set to dynamic.
I had exactly the same problem with my D2. I also had it on my Cruise with the later ROMs. The official HTC 6.1 ROM did not have this problem.
I experience it when I set up my wifi 802.11b/g network card in the phone to have a static IP address and set the default gateway. If I use DHCP there is no problem.
Setting the wifi card up on the phone DEFINITELY screws up the cellular data connection.
BeQuietAndDrive said:
Do you have a static IP for WIFI as well? I kinda found out that setting WIFI on dynamic IP solves the 3G problem, so somehow they must be connected. But this should be able to work, it's almost as if 3G 'takes over' the static IP from the WIFI settings, but the connection settings from my 3G are offcourse set to dynamic.
Click to expand...
Click to collapse
I use a dynamic IP, for me it doesn't work.
With my dear old Wizard (MDA Vario) I had no problem at all with the same settings!
yup thought i was the only one with this problem need a fix for it soon man otherwise we are gettin bumped for not havin the settings coz we on t-mobile
I solved it temporarily by setting Wifi to dynamic IP, but this prevents me from connecting at work. I'll send HTC an e-mail, let's see if they are willing to hot-fix this one
for me i find that the web sites work but any app that requires to go online ie facebook, msn, sky fire etc jus dont work wen you try to connect online......... stupid t-mobile
My connection problems are gone.
Maybe I (we) encountered hickups with the T-Mobile proxy-server....
maybe You can help me.
I have a MDA V (germany T-Mobile) and i can not connect to my AP here at Home.
I have a ASUS WL500g configured as AP behind my Firewall/Router. All other device in my house, a Laptop, a Netbook and a 'WII' working fine!
All get the IP from the Router, the AP works transparent.
D2 will not connect. The Mac-Address from the D2 is configured in the AP, and i can see the router statuspage and see the MAC of the D2 sometimes in the list. But only as "associated" and never as "associated authorized" as the Laptop here in example:
-------------------------------------------------
Stations List:
-------------
00:23:76:yy:xx:xx associated <-D2
00:1C:BF:yy:xx:xx associated authorized <- Laptop
--------------------------------------------------
I configured a lot in the settings, but i cant get the D2 online with wifi.
Can someone plz help a bit?
-
other question: if i manage the problem some day, is it possible to configure the Networksettings of the D2 device in the way that the device only use USB and te WiFI-Connection to access the internet? I hat it that the device use mobile-internet connection without asking me to do so.
Same problem
BeQuietAndDrive said:
I solved it temporarily by setting Wifi to dynamic IP, but this prevents me from connecting at work. I'll send HTC an e-mail, let's see if they are willing to hot-fix this one
Click to expand...
Click to collapse
I was experiencing the same problem, only with the difference that I am using 3 different Wi-Fi adapter settings every day (for 3 different networks - two with fixed IP and one with DHCP enabled. Most elegant solution that I came up with was a small, but very handy application called "WiFi Profiles". Settings for WiFi adapter are easily changed by choosing a profile that you want to use and applying it. Before you disconnect from WiFi network, you just set adapter to DHCP, and after that your GPRS/3G/HSDPA connection works like a charm. By the way, I am proud owner of Touch HD but I am using Dutty`s Topaz based rom V3.4 XTREME SHIP.
Hi,
I have had a quick look and found no answer to this issue.
I have an XZ2, which has worked faultlessly until a few weeks ago. The result is that when at work my connects to the network but shows 'connected, no internet'. It used to work on the network no bother. I have checked without IT dept and they can see no reason why it shouldn't work (ie it's not blocked on the network)
This appears to coincide with us getting a new router at home, We binned BT and moved to 4g Broadband from 3. Now when I connect at home it says connected no internet, then after a few minutes it gets internet connection. Sometimes I need to restart the phone. At work restarting makes no difference. I have tried:-
a)Forgetting the network and re-joining
b)reset network settings
I have read that the only fix is a factory reset of the phone. But I am hoping there may be a better solution to this.
Thanks
I am still having issues with this. I have tried starting the phone in 'Safe Mode' but still will not connect to the internet through my work network.
Does anyone have any suggestions?
Thanks
bit the bullet and did a full reset on the phone. Still getting 'connected, no internet'.
I am assuming that there must be an issue with the network/router at work if this is still happening after a reset. Although our IT has checked my mac address, DNS and IP address and say all are correct.
Well, looks like I may have resolved the issue. just as a last-ditch attempt I did the following.
1.Settings
2.Network & Internet
3.Advanced
4.Private DNS
In here you have three options. OFF, Automatic and Private DNS Provider.
Mine was set to Private so I changed it to Automatic.
It seems to have fixed the issue. Not sure why as this is not a setting I have ever changed.
Calcifur said:
Well, looks like I may have resolved the issue. just as a last-ditch attempt I did the following.
1.Settings
2.Network & Internet
3.Advanced
4.Private DNS
In here you have three options. OFF, Automatic and Private DNS Provider.
Mine was set to Private so I changed it to Automatic.
It seems to have fixed the issue. Not sure why as this is not a setting I have ever changed.
Click to expand...
Click to collapse
Weird, it is automatic by default at my side.