First of all i do not know where to post this. I have had a HTC wizard for over a year now. it has been working fine after cooking up wm6 and installing it for 6 months. today when i restartet the phone pulling the battery out and inserting it, the phone starts up, then the blue screen comes and shows ispl etc, then windows image shows, there it stops. i do not know what to do. It has been a while since i did pocket pc modding now, and i have forgotten all about it.
Alexander, [email protected]
Maybe something crashed the OS software.
Hope you have a system backup, or at least PIM backup using ActiveSync because what you need now is a hard reset.
Punching the reset hole (next to IR window) while holding CommManager+VoiceDial, then press "Dial" as prompted.
how do i hard reset my dash/s620?
i have tried hard reset
i have hard reset the phone. i do not have any backup in active sync. and i dont think that matters. because my phone does not connect to activesync since it does not start up. and in the three colored boot mode the phone is not detected by active sync. when i hard reset the phone it just came to the same point and freezed
If you didn't touch the ROM for long time, then it is probably a hardware failure...
lovemy318 said:
how do i hard reset my dash/s620?
Click to expand...
Click to collapse
READ YOUR PHONE MANUAL, and THIS IS NOT DASH FORUM.
hard to believe
First off, thanks for fast responses.
It cant be hardware(Not as a total theory of course) or likely not, because phone was not touched by water, shock, bumb fire or anything. it laid on my desk, worked, laid on my dask more, freezed. and it has been working for 6 months with wm6. is there anyway i can flash something into it. without activesync, but in the three colored boot mode?
Get into bootloader, plug in your usb cord and give it a minute...ON THE TRI-COLORED SCREEN do you see in the bottom corner "USB"??? If yes, you are OK. Get a stock rom such as the Tmo 2.26 and flash that. If you do not see "USB" in the bottom corner then as far as I know, you are fukd.
For more info on issues, read the linky in my siggy. There is valuable info there that may help with other ways to flash a rom.
Good luck.
i see usb
thanks, guess i am not fked then
Only problem is i have forgotten all about this now, and that i am sorry for.
But i have to ask you, as from norway wich stock rom to choose, what is stock rom, and when you say bootloader, is that an expression for the three colored screen or is that a program, that can flash in three colored screen? Thanks, i do not expect an answer on this noob questions, but i would really apreciate answers.
stock rom & bootloader
stock rom is the rom which comes with ur phone while purchasing it.. u can call it base rom..bootloader is tri-coloured screen which is bios for ppc if it gets fked then phone is bricked..next time if u cant boot up, then u can flash ur phone with the help of bootloader...
that was fast
thanks, but i do not think i have the rom that came with my mobile phone:/
and i do not know how to flash from tri colored screen, because all the files i have tried cant detect my phone.
ipl adn spl are 3.08 if that helps anything.
that was fast
is there an app you use to flash from tri colored
there is no need for any app, just connect ur phone to tri-coloured screen..u willl see usb in down left corner.. then ur phone is connected then run RUU utility.. if any problem comes i am online at hotmail... [email protected]
Can you power down? If not, remove battery for 1 seconds, the re-insert. Then press all at once the camera, comm and power buttons (or I believe you can also press the camera and soft reset. It is in the wiki explaining, as are some stock roms. Use any stock rom if you plan on flashing a cooked rom. The Tmo 2.26 is a decent stock rom, there is a 3.08 on the forum somewhere that you can also use. Get a stock rom. Get into the tri-colored bootloader. Look to see if it says usb in the bottom corner. If yes, connect your cable and using the ruu from the stock rom, flash your phone. Once a stock rom is installed follow the directions to cid/sim unlock your phone. Once unlocked, you can flash any cooked rom.
PS- I am assuming you have a G3 phone.
PPS- reading the wiki and the stickies are very helpful. Give them a try.
im sutch a noob
yeh i got same problem... i will try a hard reset but im at school... hope it fixes it... i got imate jasjam... BETTER WORK OR I WILL KILL MY BROTHER 4 STUFFING AROUND WITH MY PHONE
im sutch a noob
gah... it diddent work what do i do now????
Related
I cant believe this....I had no issues all day upgrading the ROM...until my PC overheated and shut off at 57%...
now when my phone starts up I see the 3 bars and it sais USB in the bottom left...but active sync is not connecting!
help!
what 3 bars?
a Red Blue Green Bars color?..
If that so.. you are too lucky..
I read a little more on the wiki:
Type 2a: When the phone boots, it goes directly to bootloader mode (tri-color screen)
This is what I have right now...I can't seem to get active sync to connect...although at the bottom of the screen it has "USB"
I have tried using mtty and dont think its diong anything...
Just stay in the bootloader (tri-color screen) and make sure the "USB" is shown in your device screen..
The reflash.. even if its not sync/connected.. just reflash the ROM..
Everything will be fine..
wow....i think it may actually work....that was SCARY.
nice to know the good ole button flash works when all others fail
I just want to make a clarification..
You are just flashing your device and when the upgrade process is on 57% your computer suddenly shutoff? and the upgrade was cut..
What happened next? did you reset the device then went to tri-color screen? or you just force bootloader mode it?
Yeah pretty much exactly what you said. I literally got up for a second to get some water, came back and saw the telltale sign that my pc had just shut itself off (the screen was black except for the standard boot junk that shows up).
So I look at my device (8125) and it was locked at 57% and was not responsive. I figured that the flash util probably wouldn't continue after the computer started back up (and besides, the device wasn't alive anymore) so I rolled the dice and unplugged the USB and took out the battery. When I put the battery back in and hit the power button, it went straight to the bootloader (the tri color screen).
- By the way - ive got the button image on here now - workin like a champ...
tnx for the explanation..
have fun!!..
thanks for the quick reply - i thought i was completely stuck but the button flash seemed to take care of everything. Makes me almost think that bricking this thing is near impossible... >
Yup!.. that also my conclusion.. its impossible to brick.. thats why i ask for your clarification..
What is this "button flash"? I am stuck in RGB boot mode with no activesync connection. I have read til my eyes crossed, but can not fix my 8125 (G3)!
Please advise.
How about more information? On your bootloader (Rainbow screen) what does it show the IPL / SPL to be? What were you trying to do when you got into this situation? What happened when you were flashing? Is your device a G3 or G4?
Safest thing for you to do right now is to flash your carrier's rom onto the phone (an official shipped ROM). With your phone in the bootload, just run the ROM and it will install (DO NOT RUN A CUSTOM ROM AT THIS POINT SINCE YOU HAVEN"T TOLD US ANY OTHER INFORMATION).
G3 8125
ipl/spl 2.25
Was trying to use faria's latest rom...got stuck at 99% for almost one hour, so I rebooted computer and discon'd the wizard. Now it will boot to rainbow screen and will not connect via activesync (so I can't utilize any other roms to get back to square one).
ActiveSync will NOT connect when you are at the boot loader. As long as you see USB in the bottom left of your phone (above the left soft key) then you can flash your original Cingular ROM and be good to go again.
brick, brick, brick
It happend to me too with faria´s new crossbow rom:
the device freezed at 99% and I reseted it then....nothing happend- bootloader mode: red green blue + usb... but no chance to flash ANYTHING... always the same message:ERROR (260) update error, no connection to the device...???
I tried the O2-mini s update, and the faria rom, no chance just a brick
I need help....
Hunter6 said:
It happend to me too with faria´s new crossbow rom:
the device freezed at 99% and I reseted it then....nothing happend- bootloader mode: red green blue + usb... but no chance to flash ANYTHING... always the same message:ERROR (260) update error, no connection to the device...???
I tried the O2-mini s update, and the faria rom, no chance just a brick
Click to expand...
Click to collapse
Why did you reset it??? All roms freeze. The screen that is flashing the ROM even says it can take up to 10 mins. If you don't get an error onthe PC then DON'T stop the flashing process.
Go get a copy of your carrier's official ROM (not a custom one, but an official one from your carrier.). Then with the phone at the boot loader (Rainbow screen) and the USB cord plugged, in, run the official ROM. If that doesn't work, then get a copy of the Wizard Love rom and flash it (You'll need to find links around here for it, or pull it via PirateBay). You may also want to reboot the PC you are running on and remove your SD card (if you have one) just to remove variables that can play in to all of this.
Good luck
mfrazzz said:
Why did you reset it??? All roms freeze. The screen that is flashing the ROM even says it can take up to 10 mins. If you don't get an error onthe PC then DON'T stop the flashing process.
Click to expand...
Click to collapse
Ten minutes is understandable, but mine stalled for about an hour at the 99% mark. Even my PC would not respond. Is that normal for a rom upgrade?
-----
I was finally able to reset my 8125 to the Cingular ROM. Not sure why I couldn't do it on my PC, but after moving over to my wife's PC I did not have any problems.
Thanks!
brick, brick, brick
o.k. boys, now it is a nice little crossbow brick from faria.....and I can make telefon-calls with my brick.
thanks a lot for your help
entdiablo said:
Ten minutes is understandable, but mine stalled for about an hour at the 99% mark. Even my PC would not respond. Is that normal for a rom upgrade?
Click to expand...
Click to collapse
No, that sounds like your pc locked up or something (I'd blame windows on that one )
I was finally able to reset my 8125 to the Cingular ROM. Not sure why I couldn't do it on my PC, but after moving over to my wife's PC I did not have any problems.
Click to expand...
Click to collapse
Glad to hear you got it going. Good luck and be careful out there!
Hunter6 said:
o.k. boys, now it is a nice little crossbow brick from faria.....and I can make telefon-calls with my brick.
thanks a lot for your help
Click to expand...
Click to collapse
Sorry, I may be missing your humor or sarcasm... Are you saying its dead (if so, give more details about what it does or doesn't do, IPL/SPL it shows (if it turns on), etc... If its now working, then congrats!
Ok, so today I tried to flash my Rom with the official att 6.1 rom from HTC. I got it to finally start flashing after about ten tries but when it reached about 13% it gave me an error 276 I think. I tried the recovery method suggested by removing the battery for 3 seconds and reseting the device but now my device isn't recognized in windows and I can't run the upgrade file anymore.
It just goes to the bootloader screen with "KAIS1*0" on the top, then "SPL-3.02.000" below that, and "CPLD-8" below that. At the very bottom it shows USB but my computer doesn't recognize the device. I've tried hard reseting it and it just goes back to the bootloader screen.
Is there any way I can get my Kaiser back or am I screwed?? All this waiting for 6.1 and now my phone is dead. What a load of crap.
Just re start the ruu and let it sit for a minute when that happens, it will start again by itself. Almost shat myself when it happened to me.
First of all, relax. Your phone is not bricked. Do a little looking around the forums and you will resolve this.
I am too lazy to search for him but is the 3.02 SPL compatible with the 6.1 ROM?
I can't restart the Ruu because I can't get a usb connection to my phone. The bootloader goes into usb mode but my computer does not see the phone. The Ruu says it cannot detect the phone either.
Isn't there a way this guy can re-flash using a MicroSD card?
MineralGray02K said:
Isn't there a way this guy can re-flash using a MicroSD card?
Click to expand...
Click to collapse
I'm not sure if the OEM SPL has the ability to flash from card like the Hard SPLs.
To test put the Carrier ROM (Download from the Wiki) on to the root of the MicroSD Card and call it KAISIMG.NBH. Turn on the Phone with the Camera Button Held Down. It should try and flash the ROM then. If that doesn't work, I have a thread and wiki page all about getting stuck on the bootloader, check my Sig for more info.
Hope this helps.
Dave
rodavery said:
Ok, so today I tried to flash my Rom with the official att 6.1 rom from HTC. I got it to finally start flashing after about ten tries but when it reached about 13% it gave me an error 276 I think. I tried the recovery method suggested by removing the battery for 3 seconds and reseting the device but now my device isn't recognized in windows and I can't run the upgrade file anymore.
It just goes to the bootloader screen with "KAIS1*0" on the top, then "SPL-3.02.000" below that, and "CPLD-8" below that. At the very bottom it shows USB but my computer doesn't recognize the device. I've tried hard reseting it and it just goes back to the bootloader screen.
Is there any way I can get my Kaiser back or am I screwed?? All this waiting for 6.1 and now my phone is dead. What a load of crap.
Click to expand...
Click to collapse
run this while phone is hooked up to computer stuck in bootloader.
Sweet Jesus
Ok, I tried the tri-color fix from nufsaid. It didn't work b/c it couldn't open a usb port or didn't see the phone or something. Then I tried putting the rom on my microSD card.
And *SHAZAM* there it was. DaveShaw you are a god to me now. It said the update was successful but I'm still stuck in the bootloader. It used to work if I would plug it into the wasll charger and reset it but that isn't working now. My computer still doesn't recognize it so Mtty or anything still doesn't work.
Ok, I left my tilt on the tri-color screen all night long to run down the battery. When I woke up I tried to power it on and I got the familiar ATT flash screen but when I plugged it into the AC power it went straight into the bootloader.
I don't know what's worse, bootloader or red light of death, I just experienced the red light, called att and got a new phone sent out in 12 hours! What SPL does your phone show? they might exchange if it's not 'voided'
ok, I finally got it to load the windows. If the battery has a high charge or is charging resetting won't get out of the bootloader. If I let the battery run down to almost nothing, wait a little while with it out, then try it again it will turn on. my spl is now 3.56.0000.
Finally
I finally got it out of the bootloader. I'm never going to reset my phone again. It's gonna suck if it freezes. Thanks for all the help.
rodavery said:
I finally got it out of the bootloader. I'm never going to reset my phone again. It's gonna suck if it freezes. Thanks for all the help.
Click to expand...
Click to collapse
Glad your back up and running. There are two new hard SPL's be cmonex (they are mentioned in the link in my sig) that make it less likley for you to get stuck at the bootloader. You could try those?
Ta
Dave
Hello guys!
Sorry my bad english!
I installed to WM6.5 ROM in my HTC phone in february. I used may months, all day...
And yesterday i switch on my phone, put on my desk, and today, i see , that the screen get white. It dont do nothing, just get white. I restart the phone many times, and remove the battery, the phone do this: i enter my security password (i locked my phone) and then its go to white screen, and dont do nothing. And if i swich on my phone, and dont do nothing, its just go to frozen...
A dont install nothing my phone since many weeks.
Maybe, the WM6.5 ROM was out of date???
I dont know, but if i connected my phone to PC, the PC isnt known my device...
I dont do nothing, my phone was dead, and im a big trouble (((((((((((
PLEASE HELP ME!
did u try to hard reset it?
can u still enter bootloader mode?
if u can still enter bootloader then try flash another ROM
I think there is a timebomb in the Rom you are using.
Go to bootloader menu, connect to usb, and try to flash an other rom by installing via Windows.
okay, but what is the hard reset? Is that a red button on my device back?
if it is, i try this, but it isnt solve my problem.
and how i can go the bootloader menu?
thank a lot.
Don't worry...just try the hardreset:
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to the manufacturer default settings. Press VolUp to restore manufacturer defaults, or press other keys to cancel.
3. Release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
If this does not work...just flash another rom...it really seems to have this timebomb issue...you don't have a hardware problem...it's just the software.
here's a video instruction for the hard reset:
http://www.youtube.com/watch?gl=DE&hl=de&v=Eqg8XFJyHBY
thanks a lot, the hard reset worked!!!
thanks!!!
i will flash a new 6.5 ROM.
VorosAdam said:
Hello guys!
Sorry my bad english!
I installed to WM6.5 ROM in my HTC phone in february. I used may months, all day...
And yesterday i switch on my phone, put on my desk, and today, i see , that the screen get white. It dont do nothing, just get white. I restart the phone many times, and remove the battery, the phone do this: i enter my security password (i locked my phone) and then its go to white screen, and dont do nothing. And if i swich on my phone, and dont do nothing, its just go to frozen...
A dont install nothing my phone since many weeks.
Maybe, the WM6.5 ROM was out of date???
I dont know, but if i connected my phone to PC, the PC isnt known my device...
I dont do nothing, my phone was dead, and im a big trouble (((((((((((
PLEASE HELP ME!
Click to expand...
Click to collapse
I'm curious wich rom you use?
you CHICKEN >"<
quack quack
vodanh2025 said:
you CHICKEN >"<
Click to expand...
Click to collapse
lol chicken?
Sorry, but its dont solve my problem, all 6.5 ROMs go to freeze a few sec/minutes when i use... And the phone function and network connection also dont work. Big trouble (
and all rom go to 256 depth colour screen, when im swich on my Blackstone...
but when i push the power button, and push again, the screen go to normal.
but, if i use the device, go to freeze all of ROMs...
brühühühüüü
VorosAdam said:
and all rom go to 256 depth colour screen, when im swich on my Blackstone...
but when i push the power button, and push again, the screen go to normal.
but, if i use the device, go to freeze all of ROMs...
brühühühüüü
Click to expand...
Click to collapse
Flash the latest Hard SPL http://forum.xda-developers.com/attachment.php?attachmentid=179550&d=1240516932
I'm curious, what way did you flash these roms. Are you using USPL or HSPL or have you just flashed these straight from stock?
i used an older february HSPL, now, i will put on my device the latest version, thanks the idea!
VorosAdam said:
i used an older february HSPL, now, i will put on my device the latest version, thanks the idea!
Click to expand...
Click to collapse
2 versions of HSPL, 1.14 & 1.56. You will need HSPL 1.56 on your device to be able to use roms based on 1.56+
thanks a lot, i flash the new HSPL, and now, all phone function back to normal!!!
THANKS!!
Impressed by the support
Hello,
I was watching this thread continously and whenever i try to jump in to help you with tips about flashing, someone would have done it already.
I feel somewhat releived to know that your Kit(d) is back on track.
I like this forum very much not just for the solutions but also for the people's attitude.
I've been waiting for hours for someone to help me and I searched and searched, I can't find any help!!! I have to go to work soon and I've been on this screen since 7:30AM EST!
Looks like I'm stuck at the boot loader screen and it goes back to it when I do a soft rest. I can't do a hard reset since I can't turn off the phone.
I think it's the bootloader screen.
Says RUUNBH on the top right corner and the screen is red, green, blue and white which these codes or whatever.
Took the battery out for a few and it went right back to that same screen.
Can someone help me bring back my Rhodium to stock???
EDIT: I might of posted this in the wrong section. Should this be in Rhodium General?
*UPDATE*
ark666 found the stock rom for T-Mobile HTC TP2 and I did a flash to get it back! Thank you so much ark666!!!
Flash stock rom.
I have no idea on how to do that, I searched how-to's but I can't find any full instructions or where to get the stock rom for T-Mobile HTC TP2.
This is the worse ever!!! Somebody please!!!
Isn't this the best site for things like this?
Try a manual hard reset? The instructions should be in your manual.
It says while the phone is off to HOLD SEND/END key with the power until the message comes up. The phone wont turn off unless I take out the battery for me to do a hard reset.
EDIT: I took the battery out then put it back in. The phone is now off, I hold the buttons and did the hard reset. It went right back to the boot loader screen.
hi,
what happend after you hard reset the device?
regards,
twisted
Asked me to press the VOL UP button to reboot. I did and it went right back to the boot loader screen. A flash happened on the screen when I try a soft reset and it says really quickly!..."NO IMG FILE" then it goes back to the 4 color screen.
EDIT: Image below on how my screen is since 7:30 AM EST!!!
on some device, active the RUU, connect it to PC & press soft reset button (the one in side the battery cover).
don't know if it help, just try that
good luck
Thanks for the reply, but that was the first thing I tried. Looks like I will have to go to work with no phone! This is crazy on how this can't be resolved.
Looks like you've basically erased the flash I'd say...
If you can get the t-mobile image, then try flashing that back to the device... If you connect a usb cable to your device, at the bottom, where it says serial it'll change to usb...
Or, if you have a goldcard, maybe try installing another image. But I'd say you're best to install the t-mobile image if you can get one?!
Ok so where can I get an image that will work on my phone? I also will need instructions on how to do it properly.
HeavyComponent said:
Ok so where can I get an image that will work on my phone? I also will need instructions on how to do it properly.
Click to expand...
Click to collapse
Where are you from? Can you find the rom on your tmobile site?
Or, creat a goldcard, copy the RHODIMG.nbh into the root of the card and try flashing that...?
As far as I know, your device is not bricked, you simply need your original supplier rom...
I replied to the PM (basically do set 16 0 command in mtty)
but I see your photo now - you have 0.85.1000 SPL? that's mfg SPL so if "set 16 0" did not help (you didn't describe what you did to the phone when this happened), you can just take any official rhodium ROM and flash it
sorry if I misread your photo... quite blurry
Ok that's my main problem that I've been having. Where can I get an official Rhodium ROM and how do I do a flash? I've been searching all morning.
And yes 0.85.1000, that's what it says on the screen.
I tried to this ROM...Link: http://forum.xda-developers.com/showthread.php?t=548546
Did the goldcard, but I think I did it wrong. I added the RHODIMG to the SD then tried to update my TP2. That's when I got an error saying it's not for PDA and how I need to update my utility.
I got the steps to do the goldcard correctly, I just want to take another shot at updating this ROM.
lovelldr said:
Looks like you've basically erased the flash I'd say...
If you can get the t-mobile image, then try flashing that back to the device... If you connect a usb cable to your device, at the bottom, where it says serial it'll change to usb...
Or, if you have a goldcard, maybe try installing another image. But I'd say you're best to install the t-mobile image if you can get one?!
Click to expand...
Click to collapse
hard reset doesn't erase the OS image.
HeavyComponent said:
Ok that's my main problem that I've been having. Where can I get an official Rhodium ROM and how do I do a flash? I've been searching all morning.
Click to expand...
Click to collapse
see my PM first, maybe set 16 0 will be enough.
is your SPL version really 0.85.1000? how did you get this phone? what happened when it got stuck on bootloader screen?
as for flashing, see xdadev wiki on rhodium.
Ok, will try what you PMed me. Brb!
It says 0.85.1000 on the screen so I guess so and I got it from T-Mobile. Ordered it through Customer Service.
post #15 has been updated to let you know what I was trying to do.
HeavyComponent said:
Ok, will try what you PMed me. Brb!
It says 0.85.1000 on the screen so I guess so and I got it from T-Mobile. Ordered it through Customer Service.
post #15 has been updated to let you know what I was trying to do.
Click to expand...
Click to collapse
then the set 16 0 will work just fine
weird the rom didn't work though
I have just flashed the 6.5 rom which you flashed
It does change the spl to 0.85 and i have the exact the sameimage which you have shotted during the flash process. But the process of this rom's flashing has two stage, it will restart after first 10% and show up the image which you shotted and upload, and continue afterwards. i guess ur goldcard has the problem so it stops and stucked there. Try other sign roms would be a better solution.
yesterday i installed the rom of one of the above threads (win 6.5.28052) but everytime i boot up my device (when it is installed) it crashes.. constantly the same screen and i cant do anything?
i wanted to flash it to another win 6.5 rom. but i cant even turn on active sync on my phone
can anyone help me?
and fast. because i cant call and sms..
oh and: sorry for bad english
One post below is an exploit that seems to work without activesync, You could try this : http://forum.xda-developers.com/showpost.php?p=5336477&postcount=379
If I`m right it should connect again after You have a new SPL onboard. Relatively new here myself...
Another method would be to flash directly from an old SD card (not a new micro with adapter).
Edit : Maybe I misunderstood "turn on active sync on my phone" : Are You trying to flash when in bootloader mode (tricolor screen) ?
i was not flashing my phone in tricolor screen. but i did saw that screen when i installed the new rom?
but how do i come in the bootloader?
EDIT: can u please explain me in steps how i have to do this? (i am not so smart in those things..)
and how do u flash with a SD card?
another EDIT: i came a little bit further. no i see the commanager screen and disabled everything, then i tryed to turn on active sync. but then it freezes I WANT TO USE MY PHONE AGAIN!
Where did you find 28052 for trinity?.
Bootloader mode push on+camera botton+soft reset.
it was an older version.. typed it wrong. it was 28014..
but do u have a clue how i can fix this?
EDIT: now if i unlock my device. i get the windows screen when it boots up and does nothing.. so i cant do even less..
Ths to Supersport:
My recommendation for Flashing is:
Make sure you have Hard SPL on your Phone. I recommend Olipro 1.20 - Click Here for More Info
Be sure your battery is at least 50% full.
Start your phone in Tri Color Screen mode. Steps below
--Unplug your phone from USB
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
--Plug in the USB cable (if asked about installing a driver, do this), You should see USB in the White Box)
Now you can Flash.
And take a look also here:
http://forum.xda-developers.com/showthread.php?t=576880
Bye
atropo said:
Ths to Supersport:
My recommendation for Flashing is:
Make sure you have Hard SPL on your Phone. I recommend Olipro 1.20 - Click Here for More Info
Be sure your battery is at least 50% full.
Start your phone in Tri Color Screen mode. Steps below
--Unplug your phone from USB
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
--Plug in the USB cable (if asked about installing a driver, do this), You should see USB in the White Box)
Now you can Flash.
Click to expand...
Click to collapse
that tricolor screen says:
TRIN100
IPL-0.50
TRIN100
SPL-1.20.Olipro
so the spl version is good?
what to do next?
EDIT: what happens when i reset everything to factory standard?
ok. i did the steps u gave and i am flashing now..
now see what it does..
ow and btw.
how u can do dual boot on this phone? maybe i want android on it if it is possible
where can i find a good version of windows mobile 6.5? becuase the version i have now i dont like.. but the other version i tried was wrong?
Glad You found some help, I currently only have internet access at work...
What a good ROM is depends on Your liking. If You want a clean 6.5 base to install stuff Yourself and have lots of free RAM for bigger apps, check the second post of
http://forum.xda-developers.com/showthread.php?t=551424
The one my phone came with was also from xda-devs but couldn`t run iGO (nav software) because there was too little free RAM, too much preinstalled stuff running like Manila eyecandy...
So if You want a ROM with fancy today screens and other preinstalled stuff You`ll have to take a look around here, otherwise check the one above, many ppl recommend it.
Happy flashing
@flyby.
i dont like the standard skins of windows mobile 6.5 but i like the start menu and the file explorer thing,
and i used SPB Mobile before and i like that!
but what is the lightest version of windows mobile 6.5 here on xda? without that fancy touchflo etc, only the good start menu in the top and a good file explorer were u can scroll with u finger?