Please Help! - Tilt, TyTN II, MDA Vario III General

I dont know what happened, i was flashing Duttys 2k rom onto my phone, ive flashed other roms before... but for some reason my comp turned off and it was only at 50% done for flashing. Now my phone is stuck at the tri-colored screen.
Please help.

bump.
Once again please help.

noone can help?!!?

As long as you put HardSPL on your device before you started flashing you should be able to just start the flash over.

it wont let me start the flash over, because of the fact that it says im not connected to ActiveSync

You don't need an A/S connection. Just make sure that when you plug it in it says "USB" at the bottom & you're good to go.

Related

flash rom from sd card?

Iv searchd the forum first orry if i missed it i am wondering how i can flash a new rom onto my wing using the sd card. i flashed to pdaviets 6.1 rom and earlier today all my comps quit recognizing it so it wont sync up ive reinstalled active sync hard reset the phone i dont know what to do someone please help me
no one can help?
Please don't doublepost. If no one has answered they've either been sleeping like me in my time zone, or they don't know.
Place your phone in bootloader mode, by holding the camera while pressing the reset button. Then run the stock RUU from there.
sorry didnt mean to double post. even when im at the boot loader screen ot usually says that its connected by usb and right now it wont do that its wierd cause i can still charge it from the usb cord it just wont recognize my phone or something

I flashed GSM ROM over CDMA Lika RETARD! HELP!!!!

Did something extremely stupid......
I Flashed a GSM ROM (DUTTY's 5.2 ROM) onto a Sprint CDMA phone. STUPID! I wasnt paying attention and I dunno why I did that maybe cause i saw the features on XDA and normally I'm on PPCGEEKS but now I need Help. Is there anyways of getting a CDMA Rom back on the phone. I can still get into bootloader manually. But i Need to be able to transfer a CDMA ROM to the internal Memory. Is this possible without fully booting into Windows Mobile?
Thanks for ANY suggestions!
I'm not sure, but the difference between isn't in the OS rom, but in the radio rom.
But it should be possible to flash another rom directly from the operating system with the tool delivered with almost every rom. Enter boot loader and then connect via usb.
my comp is not recognising the internal drive
pretty sure you bricked your phone
I too did this when i first started flashing my phone because i did not know the diff between GSM and CDMA , so this is what i did to fix it
1.turn the phone on to bootloader mode(tri-colour screen) to do this power the phone on while holding the the volume down key.
then
2.plug your usb in and wait for it to say usb on the bottom of the screen,
3. now flash your phone with a stock rom
this is what i did and the phone was fixed good luck post back with your results
I did the same with my phone and I burned it. I sent it to service and they change the entire motherboard.
apaquette420 said:
I too did this when i first started flashing my phone because i did not know the diff between GSM and CDMA , so this is what i did to fix it
1.turn the phone on to bootloader mode(tri-colour screen) to do this power the phone on while holding the the volume down key.
then
2.plug your usb in and wait for it to say usb on the bottom of the screen,
3. now flash your phone with a stock rom
this is what i did and the phone was fixed good luck post back with your results
Click to expand...
Click to collapse
Windows does not recognize anything when in bootloader mode. =( New phone on the way... if someone can gimme a fix for this I will pay pal them $$$...
WOOT fixed it!!!!
Using <--, vol-down, and power-button sequence:
First Bootloader will automatically try to flash DIAMIMG.rom which is still the ROM that messes up ur phone in the first place do to user error. I went ahead and let the WRONG Rom install about half way then pulled the battery. I then turned the phone back on and to bootloader screen says " Rom Upgrade Failed, Please try again..." I then plugged in USB cable and the phone detected the USB plugged in. Then went and ran rom upgrade utility via windows.... and presto! Phone fixed. Whew... I had all my contacts, pictures of kids and video all saved on internal storage. I hope this help someone as stupid as me.

Need Help! Bricked Phone??

Hey all,
I was trying to upgrade my Topaz to WM6.5 and obviously something went wrong.. Now when I turn the phone on, it goes to the tri-colour screen but displays the message Upgrade ROM code error please try again. After that, it goes to the white loading screen and just stays there until the numbers 00068002 in red appear at the top of the screen. Then it goes back to the tri-colour screen. I've searched the forums and tried some of the suggestions out there. Nothing has worked! Was wondering if someone could really halp me out with some step by step instructions!! Thanx in advance!
PS: I have HardSPL 1.83 installed already. That installation went well without any problems. It was when I went to flash the rom this happend.
i would suggest downloading another ROM (try the orginal ROM of your language http://forum.xda-developers.com/showthread.php?t=576620) and copying the TOPAIMG.nbh onto your storage card (ROOT DIRECTORY). now turn the phone on by pressing volume + and power button and then follow on screen instructions.
good luck!
dont worry, just a bad flash because of a corrupted rom
redownload the rom or any other rom.
use the card flasing as described by Drag-on or remove the storage card, (just tomake sure it does not see the rom image on it). connect it to pc. wait untill it shows usb on the 3color screen. wait untill the pc is finished installing drivers and then start the customRUU. that came with the rom you are insatalling
that should do the trick
success
Here's the thing, when I connect the phone to the PC, the PC can't find the phone anymore.. Well, it is connected, but it's not showing up on the computer.. I also don't know the original rom language for my phone.. My serial number begins with HT947L, anyone know?? I tried installing from the computer but it gives me the invalid vendor ID error..
ur computer is not suppose to read it like it would normally. (it wont recognize it in device center) but its connected. use the ruu that comes with the roms u download and u should be able to reflash ur device and dont worry its not bricked.
if u trying to do it manually rename RUU_signed that u get when u download a rom. rename it to topaimg and copy it to the root of ur microsd. then insert the card into the phone and turn it on. now ur phone should recognize the new rom and ask u if u want to install it. hope this helps
I haven't been able to find a rom that works.. I've tried several roms.. I rename them TOPAIMG.nbh and put it in the sd card but it never works. The phone will go to the loading screen and then the numbers 00068002 in red appear and then it just goes back to the tri colour screen with the words Upgrade ROM code error please try again. It just stays there after. When I try to do it manually from my computer it keep sgiving me the Invalid vendor ID error. I'm totally stuck.
I don't know if this will help, but when trying to do it manually, the program says I don't have a img on the phone. the version of the img I have is just left blank.
Update: Thanks for everyone's help! I finally found a rom that actually worked. It installed and everything. I still don't know why it had to be that certain rom and I still don't know why I couldn't flash from the SD card method. I'm really just happy everything is up and running again. I'm never flashing my phone on my own again.. lol.. If anyone knows why I couldn't flash from my sd and why I had to get a certain rom even though I had HARDspl installed please let me know. I would like to know just for future reference.

Cry for help! D:

I tried to root my G1 from this link..
http://forum.xda-developers.com/showthread.php?t=442480
Made it through the first few steps well, until i finally began to upgrade the image dreaimg or w,e.. It failed on me & now i cannot leave the screen. I remove the battery & turn it on. but when i do it stays in the same spot.. I tried everything & need some help.. ]:
Here is a pic of the screen.. : http://img683.imageshack.us/img683/4355/picture001bk.jpg
Did it start updating, then stop in the middle of it? Did the phone turn off due to running out of battery during the flash? Did you format your card to FAT32, download the proper RC for the original sale location of your phone?
Try pulling the battery at, then removing your SD card, do a long format to FAT32 (whether it is or not) copy the dreamimg.nbh onto the SD card, put the SD card back in the phone, put the battery back in, put it on a charger not turned on for 30 minutes, then take it off the charger...
Now that you have done all that, try booting into boot loader again by holding down the camera and power button until it goes into that screen again and does it's thing.
If this doesn't work, well, good luck since I have no idea from there.
Yes i've tried all of that.. Once i remove my battery it turns on, but as soon as i put it on again it turns on & the same screen appears.. There nothing i can do to go back to the Home screen.. D':
I most likely made a mistake but now i cannot fix this! ]:
SOme onee! please help me.. ]:
Everyone continues to ignore my thread..
have you tried to reset within there by pressing Home+menu+end? ppl are not ignoring.. jus they dont kno how to help.. as the guy already gave ideas that im pretty sure everyone would have said
Jose_95 said:
SOme onee! please help me.. ]:
Everyone continues to ignore my thread..
Click to expand...
Click to collapse
When does this screen appear? Instead of the G1 screen or after it? If after, hold down home+Power and get into recovery, try reflashing your rom.
ilostchild said:
have you tried to reset within there by pressing Home+menu+end? ppl are not ignoring.. jus they dont kno how to help.. as the guy already gave ideas that im pretty sure everyone would have said
Click to expand...
Click to collapse
I tried that combination just now & it wont work either.. ]: I've tried all combinations with buttons i know to try and reset the phone to get away from that uploader thing.. But nothing works..
BTaylor927 said:
When does this screen appear? Instead of the G1 screen or after it? If after, hold down home+Power and get into recovery, try reflashing your rom.
Click to expand...
Click to collapse
That screen is the only thing that ever appears on my phone.. ]:I cant take that screen away like i want too.. So it appears instead of the G1 screen..
If that is the only screen that ever shows up, you very well may be bricked, I hate to say it.
It really sounds like during your flashing of the .nbh file it was disrupted for one reason or another, either the battery died or it was a corrupted file, so the only file left on the phone is the boot loader. Thus, it is the only thing that will show...
Of course, I am not 100% positive without knowing exactly what you did, not being able to mess with the phone myself, and so forth.
Some people have been able to bring phones back from the dead by getting lucky and being able to get ADB to work... try plugging the phone into your computer using a data cable and see if you can get any sort of ADB to work, perhaps seeing if you can get the stock HTC update program to recognize the phone and hopefully flash it into working.
pjcforpres said:
If that is the only screen that ever shows up, you very well may be bricked, I hate to say it.
It really sounds like during your flashing of the .nbh file it was disrupted for one reason or another, either the battery died or it was a corrupted file, so the only file left on the phone is the boot loader. Thus, it is the only thing that will show...
Of course, I am not 100% positive without knowing exactly what you did, not being able to mess with the phone myself, and so forth.
Some people have been able to bring phones back from the dead by getting lucky and being able to get ADB to work... try plugging the phone into your computer using a data cable and see if you can get any sort of ADB to work, perhaps seeing if you can get the stock HTC update program to recognize the phone and hopefully flash it into working.
Click to expand...
Click to collapse
So then is there anyway to restart the phone? Like a secret way? & when i connect my phone to the computer when its shut off, it appears on the computer but not completely.. it says that one of the files are not recognized. Damn, this is really a pain.. ]:
So, you cannot boot into recovery, correct? And have you tried to connect to your pc and use ADB?
rjgonza said:
So, you cannot boot into recovery, correct? And have you tried to connect to your pc and use ADB?
Click to expand...
Click to collapse
Agreed.
You should read up tutorials on ADB and see if you can use ADB to access your phone. If you can, your phone can still be recovered.
If not - then yeah, brick.
akapoor said:
Agreed.
You should read up tutorials on ADB and see if you can use ADB to access your phone. If you can, your phone can still be recovered.
If not - then yeah, brick.
Click to expand...
Click to collapse
I cannot connect it to my computer at all.. Once turning on the phone the only thing that appears is the loader thing.. Whats ADB? how can it help me?
The Search button is your friend.
http://forum.xda-developers.com/showthread.php?t=502010

Help! My Diamond cant boot and i want to flash it to Original

Hi everyone.
Ive got a MAJOR Problem here.
My Cell Phone doesnt start at all.
If i put it one the USB Cable it can Start up like 5 Seconds.
Then it Reboots and Reboots again and again by 5 Seconds.
If I Disconnect the Phone from USB screen turns Black Immediately...
I thought it could be the Batterie... but.. it worked just fine yesterday..
(have i Mentioned that this weird Sticker on it turned red..? Some kind of sign saying me it got wet?)
All this started as i got a Coloured screnn with saying ´´Serial´´ @ the bottom of the Screnn... just exact like the Flash Screen
I Flashed the Rom which is on the Internal Storage i put bevor. To bad it aint the Stock ROM!
Then i also tried Hard Reset.
But everytime i boot... i only get as far as 5 Seconds.
Is there any Chance to Flash this Baby with original ROM (Stock ROM, RADIO and SPL)
I want to send that Baby in... but if they find out i Flashed it... i wont get any Warranty... ;(
So PLEASE GIVE ME ANY ADVICES!!!!!
Try to flash with the original ROM. Go to HTC homepage-support, download the ROM and flash. It may help...
krisztian b said:
Try to flash with the original ROM. Go to HTC homepage-support, download the ROM and flash. It may help...
Click to expand...
Click to collapse
You only can Flash if u got a Active Sync connection.
So ... Cell cant boot... i cant flash...
HELP
Just go into bootloader mode (you have Hard SPL installed right?) by booting up the phone while holding down the volume down key. Then connect it to the pc with the USB cable and run the CustomRUU to flash another rom. Should work! Else you should try to MTTY (that solves the resetting stuff right?).
I was just about to say to try to get Diamond into bootloader mode manually. http://forum.xda-developers.com/showthread.php?t=405659
MTTY wont work... cause i cant boot at all
But THX for your help flashing it back to Original...
This Thread can be closed

Categories

Resources