I have a slight problem with my gps, i've installed TomTom 6 (not the newest ver.) The problem is that i don't get a GPS signal, It just say "No valid GPS signal" and I do choose TomTom Bluetooth GPS reciver. Is that correct?
I do have a problem with my Bluetooth aswell, my Sony Ericsson HBH-PV705 Bluetooth headset (handsfree) doesn't connect to my TyTN II. I belive there might be some kind of setting that i've missed...
It connected nicley with my Samsung that I had before.
And I have downloaded and Installed the HTC hotfix regarding Bluetooth.
I've tried the search, but I couldn't se that there was anyone else with this problem.
Anyone who know what to do??
First off, are you sure you really need to use the Bluetooth adapter for GPS? After all, it comes with a built in one... I'll show you my config to get an idea:
GPS Receiver - Other NMEA GPS receiver
COM Port - 4
Baud Rate - 9600
I recommend you download and run GPS Test if you haven't already. This will tell you what Baud rate and COM port you should be running on.
In regards to your bluetooth Headset, are you sure you're following the correct process for pairing the device? I remember setting mine up, it was a nightmare... until i read the instruction
I just got my tytn II and am having the same problem. I don't have TomTom, but my gps doesn't seem to work, I tried gps test but after 10 minutes it still didn't tell me anything. I can't get my headset to work either, I paired them, the phone recognizes it, but doesn't let me talk on it.
I think me and Lalla have the same problem, I can't figure it out though =/
Thanks in advance.
Lalla said:
I have a slight problem with my gps, i've installed TomTom 6 (not the newest ver.) The problem is that i don't get a GPS signal, It just say "No valid GPS signal" and I do choose TomTom Bluetooth GPS reciver. Is that correct?
I do have a problem with my Bluetooth aswell, my Sony Ericsson HBH-PV705 Bluetooth headset (handsfree) doesn't connect to my TyTN II. I belive there might be some kind of setting that i've missed...
It connected nicley with my Samsung that I had before.
And I have downloaded and Installed the HTC hotfix regarding Bluetooth.
I've tried the search, but I couldn't se that there was anyone else with this problem.
Anyone who know what to do??
Click to expand...
Click to collapse
Firstly - have you got a TyTn or a TyTn II (AKA Kaiser)? As another poster says, why are you using bluetooth for GPS. The TyTn II has GPS built in!!!
Again as said above if it's a Kaiser you have use "other NMEA" as the device not bluetooth.
If Tomtom says "No valid signal" then it has found a GPS device but is waiting for a strong enough signal. The first time you set up it may take a long time to connect. Leave it in a place with a clear view of the sky. It will also help if you have run Quick GPS from your programs menu.
Mike
edd1e said:
I just got my tytn II and am having the same problem. I don't have TomTom, but my gps doesn't seem to work, I tried gps test but after 10 minutes it still didn't tell me anything. I can't get my headset to work either, I paired them, the phone recognizes it, but doesn't let me talk on it.
I think me and Lalla have the same problem, I can't figure it out though =/
Thanks in advance.
Click to expand...
Click to collapse
Did you change any settings in "External GPS"? This can cause connection problems. (There are fixes for it though).
Mike
mikechannon said:
Did you change any settings in "External GPS"? This can cause connection problems. (There are fixes for it though).
Mike
Click to expand...
Click to collapse
Not sure if I changed it but here are the settings:
port: COM4
Hardware port: None
Baud Rate: 4800
manage gps... is checked
Thanks for your quick reply
I tried gps test but it took about 10 minutes to get 3 bars then I lost 2 :/
Maybe I just need to leave it out for a long time?
edd1e said:
Not sure if I changed it but here are the settings:
port: COM4
Hardware port: None
Baud Rate: 4800
manage gps... is checked
Thanks for your quick reply
I tried gps test but it took about 10 minutes to get 3 bars then I lost 2 :/
Maybe I just need to leave it out for a long time?
Click to expand...
Click to collapse
Actually, that sounds like it's working OK. You will notice that the Kaiser picks up and drops sats every other second. There is a thread about this someplace. In other words as you move around the sat signal will pick up and drop sats as you move (even if you are standing still) When using Tomtom or the like this does not seem to matter and it works very well.
I have found that when you first switch on the GPS make sure you have a clear view of the sky all around, then you can move to more obscured areas and it will hold a proportion of the signal. If you switch on in an obscured area, then it will take a while to acquire a fix. Running Quick GPS regularly will speed things up.
As a guide, if I switch on indoors it can take ten minutes even near a window. In the car it fixes in less than a minute (normally).
The exception is if I last switched off GPS some miles from my current location. It seems it remembers the sats position from when it was last used so if you switch on later some miles away, it takes longer - presumably 'cos it's looking in slightly the wrong place.
Mike
Ok, I'm trying GPS test right now, seems to working. Thanks for your help.
Any clue why my bluetooth headset doesn't work right? Their paired and the phone recognizes it, but I can't use it in a call.
Thanx for all the help from you all!
I've managed to fix the settings for my GPS so it works fine. But the problem with my Bluetooth is still there...but I won't give up!
go to youre bluetooth devices, find your bluetooth headset from the list and tap it. now check and see if both boxes are ticked, the stereo headset and the handsfree. now go back to the list and long tap on the bluetooth headset and set it to handsfree. that should sort it. if not try repairing it
Didn't work for me. My bluetooth headset only gives me a hands free options but it does not work. I tried it on another phone and it works fine.
Related
I need help too...
I have Tom Tom on mmc card but my Gps receiver wont connect. I always get 'no gps device' message although my device is connected. the red light begins by flashing but then stays on constant. (is this relevant?).
My incoming beams box is already unchecked.
I have XDA 2i and would like exact step by step instructions how to get my GPS to work... (I'm a new user - it took me one hour to set a song as my ring tone - so imagine how long this is taking!) I feel like I have tried absolutely everything and its really starting to drive me crazy. All I want is sat nav.
Thanks.....
XDAIIi GPS problem
Chicken,
what version of TT are u using?
what gps receiver?
If it's TT3.x, 4.x, or 5.x (don't know v6 yet), first you'll need to pair your receiver with your XDA. Go to Bluetooth Manager->Tools->Paired Devices. Here (if it's not there already) tap on Add and then tap on search icon (next to Device: field). It will search for any bluetoothdevices in range. Once it finds your GPS receiver, enter the passkey (provided with the receiver, usually 0000) and tap ok. The GPS receiver should be installed.
Start TT, go to Change Preferences and browse to Show GPS Status. Here, tap on Configure, choose your GPS device (I guess it will be Other Bluetooth GPS), click on Select (if prompted for pairing the GPS with PDA just tap on Continue) and choose the port. It'll be one of the bluetooth serial ports (it's COM6 in my case). Make sure that the receiver is still on and bluetooth active and watch the GPS status. If there is No GPS device! message on the top go back to configuration and change to another port.
If still no luck go to your XDA Start->Settings->Connections->Beam, make sure the Receive all incoming beams is not selected. If still no joy, you'll need to test all the connections, check if you can 'see' the receiver with another bluetooth device ez mobile phone, than do the same with your PDA. You can also reset the GPS receiver (check the manual), you can also do it by removing the battery from it and leave it like this overnight...
Good luck!
can you recommend a good GPS receiver?
Hi Robsonix.
Thanks for your reply. I got stuck at the first stage though - but was relieved to find out I'm not a complete dummy as this is what I had already tried - but failed. I cannot get my GPS to pair up with my bluetooth. My phone cannot find it.
I bought my receiver on Ebay. its just a wire thing that connects through my cig lighter to my phone. It didnt come with any instructions!! I think its a little dodgy. Can you recommend a proper one?
I'm not sure what tom tom it is, I think 5?? But actually I havent a clue.
I cant check if the receiver works with another phone as it only has connections for the xda 2i.
Thanks for your help - I hope u can help me some more.....
any recommendations??
Chiken
ha ha. Never mind - I think I've found the problem. I'm such a thicko!! It takes two to tango right? I'm such a thicko...
Port Numbers
chiken said:
I need help too...
I have Tom Tom on mmc card but my Gps receiver wont connect. I always get 'no gps device' message although my device is connected. the red light begins by flashing but then stays on constant. (is this relevant?).
My incoming beams box is already unchecked.
I have XDA 2i and would like exact step by step instructions how to get my GPS to work... (I'm a new user - it took me one hour to set a song as my ring tone - so imagine how long this is taking!) I feel like I have tried absolutely everything and its really starting to drive me crazy. All I want is sat nav.
Thanks.....
Click to expand...
Click to collapse
Do you select the correct port number to match your gps port number in the gps setup in TomTom?
DAz
SPV 1500 "Alpine" TT5 with GPS receiver
I've just joined this Forus following the aquisition of an Orange SPV which is now unlocked to run on T-Mobile. I have also used an MDA Compact II (Charmer?) successfully for the past year.
Like this current thread originator "chicken" (and no doubt many others) have had difficulty running my Holox BT-321 BT sat receiver with TT5. It pairs OK, but I TT5 cannot "see" the device, even though I have selected just about every Com device available.
I recently bought a wired sat receiver (just like chicken did), and thought this would work better. However, TT5 will not see this device either!
Can someone tell me how I can check which Com port is active on the PDA, or check if there is an input stream coming in from the sat receiver?
This is getting bloody frustrating now. My old Nokia 6600's worked first time out of the box!
Thanks
Peter (with the Aprilia Falco 1000)
I wonder if anybody knows if it is possible to have two (or more) divices connected at onceon a Blue Angel?
eg. Tom Tom 6 plus a hands free connection.
I have tried every configuration I can think of, different ports ect, but to now avail.
With the gps connection up and running, as soon as you turn on the hands free , the gps connection link is lost, turn off hands free and it will resume connection.
I am using BA WM5 AKU3.5 R4 - xplode's excellent rom
In GPS settings
Program is using COM 5
Hardware is using COM 0
Manage GPS settings set to Auto
In Device settings,
BTGPS unit is on COM 0 (Serial box ticked)
Hands free is unassigned
Any help will be much appreciated.
any idea's anyone?
On Last Baniaczek's ROM I made an experiment just a moment ago: BlueAngel, Navigation system (Polish one, Automapa), plus GPS on Bluetooth and A2DP headset - first connected headphones, then added GPS (using automatic GPS connection - it's M$ Stack) - Everything seems to be working fine. I thought it was a bit unstable at first, but AD2P stops sending data, when there is no sound from the device.
GPS Settings are default: COM6 for applications and GPS has COM7 assigned on Hardware tab and in Bluetooth outgoing port. Quite seamless.
then I made the 2nd one: same headset connected in Handsfree mode: indeed turning on navigation made it connect and disconnect every few seconds.
For me it seems to be fault of M$ BT stack: it cannot hold 2 similar streams on BT (COM and Handsfree/Headset are both typical serial connections of highest priority in BT stream). At the same time it can cope easily with two different streams (A2DP is lower priority, high-bandwidth BT connection).
I'm not sure, but I think when I used old Helmi 1.3.2 with Widcomm stack it could cope with GPS and Handsfree at the same time, but it needs more testing.
jakubd is right it is limitation in MS BT Stack
Don't give up and it should start to work. I have similar problem with BT GPS and BT headset. GPS goes on and off while headset is on. And than I try to switch headset off and on, BT off and on, GPS off and on and after some time it start to work together with no problem. It takes first 10-15 minutes of my voyage but then it works for the remaining few hours.
Sorry, but I still didn't find out what combination make it work. If I do, I will post it here as workaround.
And I'm almost sure that I had no such problem with Helmi 1.4 ROM.
Thanks guys,
have tried every configuration I can think of, but its always the GPS connection that is dropped, not the hands free, this would not be a problem if it was just when you are answering a call.The GPS reconnects only when you disconnect the hands free connection. ?
Has anyone Successfully used the Widcomm stack with this type of setup?
I am sure alot of members would find this usefull if it can be made to work!
This is my experience:
ROM : Helmi_BA_WM2k5_AKU3.5_v1.4.CF2.R2 (baniaczek)
Tom Tom 6
GPS : Bluetooth
Headset : Nokia BH-300
When the headset is on and connected, the GPS doesn't work (TT say no GPS found). When I turn off the headset, the GPS is working.
With ActiveSync I have the same problem: when the headset is turned on, I can't establish a connection with the PC via bluetooth.
BUT!
If I use a different headset, a Logitech HS03, all is working fine. I can leave the headset on and the GPS is working. I can receive incoming calls with no problem (using the headset) while I'm driving without loosing GPS signal.
With ActiveSync is the same: I can connect my PC with the headset on.
I have no idea why there is this difference with these two headsets, but one is working and the other no. I don't know if the problem is the MS BT stack, but my test demonstrates that under some circumstances this stack could manage more than one connection at time.
bigmike said:
I don't know if the problem is the MS BT stack, but my test demonstrates that under some circumstances this stack could manage more than one connection at time.
Click to expand...
Click to collapse
Bigmike, my point exactly. As I wrote in my post I keep turning on and off until finally it works. So there are some circumstances under coexistence is possible.
It seems that devices try to use same port which means that first device does not reserve port for itself. I am not an expert but it seems if we could somehow force devices to use different ports problem would be gone.
bigmike said:
If I use a different headset, a Logitech HS03, all is working fine. I can leave the headset on and the GPS is working. I can receive incoming calls with no problem (using the headset) while I'm driving without loosing GPS signal.
Click to expand...
Click to collapse
If this works with one set and doesn't work with another, it might be connected to list of profiles supported by the headset:
1. Headset - HSP - more common, typical profile for use with cell phones (supports AT commands)
2. Handsfree - HFP - audio-centric, used mostly in cars, less common
http://en.wikipedia.org/wiki/Bluetooth_profile
My SonyEricsson HBH-600 has both profiles (checked with services list on SonyEricsson phone), but I don't know how to select which profile is used by headset.
Just a thought...
sassa said:
Bigmike, my point exactly. As I wrote in my post I keep turning on and off until finally it works. So there are some circumstances under coexistence is possible.
Click to expand...
Click to collapse
I hope you haven't misunderstand my previous post. I haven't in mind to minimize the value of your post (very useful is someone will try to investigate about this problem).
I was thinking that somebody, reading your contribute, could wrongly think: “you're are a lucky guy and turning on-off the headset repeatedly you crash some library and the two devices are working together”.
My intention was to remark the fact that under some circumstances the headset and the gps can connect together every time and always at first try: it's not lucky, crash or random events.
jakubd said:
If this works with one set and doesn't work with another, it might be connected to list of profiles supported by the headset
Click to expand...
Click to collapse
I have a similar thought.
It seems to me that some times ago I have read that it should be possible to change some profile's parameters “playing” with the registry.... but I could be wrong...
bigmike said:
I hope you haven't misunderstand my previous post. I haven't in mind to minimize the value of your post (very useful is someone will try to investigate about this problem).
Click to expand...
Click to collapse
No I have not, bigmike, just the opposite. I was delighted that somebody confirmed my point.
bigmike said:
My intention was to remark the fact that under some circumstances the headset and the gps can connect together every time and always at first try: it's not lucky, crash or random events.
Click to expand...
Click to collapse
Couldn't agree more. And I think it's worth trying to resolve it.
Multiple BT connections - solution?
I think I find a solution for this, or maybe we can call it workaround. At least it works for me.
As I wrote in my previous posts, I could make it work every time just didn't know how. Now I established repetable procedure which worked every time for reasonable number of experiments.
Secret was to turn on BT headset (in my case Plantronics) and BT GPS device (Haicom 406-BT) and GPS program (iGo) first, and then go to Comm Manager and turn bluetooth on.
So my procedure is:
1. make sure that BT is off in Comm Manager
2. turn on BT headset
3. turn on GPS device
4. open iGo program
5. minimize iGo
6. turn on BT in Comm manager
7. open iGo and make sure it's connected
8. go to phone and call myself just to make sure it works
9. back to iGO and make sure it works
If 8 or 9 fails for the first time, just turn BT off and on again in Comm manager and check it again. I never need to do this more than twice.
Try this, guys, and good luck.
P.S. I don't know if it matters, but make sure that in Settings/Connections/GPS "GPS program port" and "GPS hardware port" is set to (None) and "Manage GPS automatically" unticked.
Very good! Many thanks Sassa!
I have tried for two times your procedure and both tries worked very well (with TomTom6 and Nokia BH-300)
I use a slightly different procedure:
1. BT off in Comm Manager
2. turn on BT headset
3. turn on GPS device
4. turn on BT in Comm manager
5. open TomTom 6 (wait some seconds and make sure it's connected)
6. go to phone and call myself (on the first call the headset is disconnected)
7. back to TomTom and make sure it works
I have noticed a different behavior of the BT headset having the BT always on (in Comm Manager) and using this procedure... but I need to make some tests before writing more.
Guys / Gals
I have just picked up a WIRED GPS reciever and want to get it to talk to my XDA11i.
I also have tom tom that I want to use .
Tom tom expects to see the GPS unit on Com 1 ?
How do I set up the XDA to recieve GPS on com 1 (Tried all sorts of things but no joy , didnt believe I was an amateur but seesm I am . I haVE TURNED off " recieve all beams " but still no joy .
Any help greatfully appreciated.
Astro
I do use Pugs rom but have read that it is still possible to link to a wired device ? if not I will have to splash out on a Tom Tom Bluetooth Gps ? or will others do ?
Firstly, I am assuming you have got some way for the wired GPS to connect to your PDA (via car cradle or similar cable).
Ensure GPS unit is switched on & running, and connected to the PDA.
Start TomTom, which will ofc bleat "No GPS device!"
Tap screen, Change Preferences, tap next twice to take you to prefs screen 3, tap Show GPS status, then tap Configure
Tap the left/right arrows until Other NMEA GPS receiver is showing, then tap Select
Accept the default BAUD rate of 4800 for now, and tap Done
Now, you will be presented with a list of the available ports that TomTom can 'see'
You will probably have several COM ports available. (mine showed up with COM2, 4, 5, 6, and 9 available for example, but ymmv)
Checking that your GPS unit is still on, select the first suitable COM port in the list, whatever it is. This will take you to the GPS status screen.
IF you are lucky enough to have selected the correct port for your wired GPS unit first time, you will now see the yellow/black wheel at the top right rotating, which indicates it is receiving data from the GPS unit. (a non-rotating wheel means TomTom can't 'see' any GPS data coming in)
If the wheel is NOT rotating, don't panic, but once again tap the Configure button and repeat the steps, this time slecting the next COM port in it's list.
Repeat this process, moving down through the available list of COM ports until you hit the one where the wheel is rotating: this indicates that TomTom has successfully 'found' the GPS unit and is receiving data from it.
Assuming you DO get a rotating wheel, click done on the GPS Status screen and you will go back to TomTom's main screen, hopefully now with the correct location showing!
Hope this is of some help.
Joe Pinball
P.S. if you have had no joy with this, or dont have/cant find a cable to connect the GPS unit to the PDA/cradle, you may well find a Bluetooth GPS unit is a better way to go (try and get one with the SIRFSTar III chipset, as it's way better performance in marginal conditions): I navigate and leave my BT GPS (GlobalSat BT338) in the car glovebox and STILL get a good signal! - Joe
Wired GPS connection to XDA11i
Joe
Thanks for the info I will try that one out tonight .
To try out the system I have picked up an early Rikaline wired unit which connects directly to the XDA11i socket as well as the car lighter socket to rum them both.
My question was did i need to do any thing to the XDA to tell it to accept the plugged in device ? as you would if you set up a bluetooth system ?
Does the XDA11i automatically SEE the device you have plugged in ?
Duncan
The XDAIIi's socket contains both a USB interface (for the cradle) audio (for in-car sounds/wired handsfree) and a serial port, so as far as I know, once the GPS unit is plugged in (and assuming it outputs the NMEA standard for GPS data, which they all seem to do) all you would need to do would be to configure TomTom with the unit plugged in & working.
Once set up correctly, and you have a decent positional fix, quit TomTom in the normal way, leave it a minute or 2 and then re-start TomTom to check it saved the settings correctly.
If the settings were stored correctly, TomTom should start (can take a while with version 5.XXX, now down to a couple of seconds with V6.XXX) and then a short while later TomTom will announce on-screen "No GPS Device!"
(note: I have a bluteooth GPS and find although TomTom is capable of switching on BT for me, it will never 'see' the GPS this way: I have to switch BT on first, THEN run TT for it to see the GPS. It is entirely possible, that with a wired serial connection, TomTom may well see the GPS data immediately and NOT flash up the "no GPS device!" message, in which case it's win-win for you!)
Be patient at this point and it should soon 'see' the GPS data coming in and get a position up on the map.
Hope this helps
Joe Pinball, now with a fixed screen! yay!
Still not working !! Doooh
Joe
After a frustrating day with the wired device I gave in and picked up a Bluenext BN-806F bluetooth gps unit .
But I am still having problems. I am not sure that the uinit is not faulty as even when paired the status shows NO data going either way . PS when I go to Blue tooth manager and then active connections there is only an outgoing connection set ???
Any chance yo can run through the set up for blue tooth gps and tom tom for me ( I have a copy of tt5.21).
Do I need to set any thing ref the Com ports / beam / baud rate ?
How do I set the time that the XDA11i holds an active connection before it times out ( if no data recieved ) as the XDA breaks the connection after a while of no activity ?
Best regards
Astro1
I connect my alpine to the gps receiver, but after few minutes, the conenction drops. I have not figured any problems with my bt hansfree.
Can anyone help??
turn off bluetooth
dropped connection
I have a similar problem . Alpine and BN806F , It pairs , wont talk then drops out ? I wonder if there is a time out after no activity ?
As my post says I am having a problem getting tom tom to see my gps reciever , do you have the some problem ? what am I doing wrong ?
Astro1
I downloaded a bt patch but the problem remains. I wonder whether it's a software or hardware problem..
Yes, I can't make my navigation program to see the gps receiver and after a while it gets disconnected...
To the OP - you said you cant get your navigation software 'see' the GPS - this is the root of the problem.
If your BT GPS unit doesnt see any requests to send data to the PDA, it will auto-switch off after a set period of time.
Once you can successfully configure your nav software to receive the GPS data, your bluetooth GPS unit will remain powered on.
You should have a software CD that came with the GPS unit (if not there are a number of freely downloadable GPS utilites for PDAs, some of which can scan for the unit to find it)- there's usually some very low-quality GPS checking utility that displays what satellites the unit can see, signal strength and so on: try using these programs to see if you can connect to your GPS, and if the unit than keeps the BT link open.
Maybe finding out which COM port the GPS unit appears on, will allow you to configure your nav software correctly to see the GPS.
Joe Pinball
I managed to connect it succesfully some times. Usually, it connects via bluetooth but it drops until I load navigator ( my navigation program). When I close the program, the bluetooth is off. I tried to search windows for power save settings but I didn't find something that would help.
GPS problems
Joe
Thanks for your advice I am still haviong big problems .
I have managed to get Tom tom to recognise a wired reciever ( but only once , and then when the cigarete lighter plug moved the unit powered down all was lost.
Do you know of any utilities that will show what is connected to what port as I believe this is the real problem . Aparently tom tom has a bad history of hijacking ports ?
It would be good to see what was actually going on .
Astro1
Hi there,
Has anyone made a TMC device working on the Athena?
I tried some version of the GNS FM9 adpaters but nothing worked.
Any ideas?
Thanks in advance for your help!
Have a good start into 2008.
greetz,
DAx
I agree - this would be very useful. I have iGo on my Ameo and it is brilliant (cant wait for iGo 8 or MioMap 2008 for the 3d visuals and road names) but it would be even better if I could get warned of upcoming hold ups on the major roads!
adamelphick said:
I agree - this would be very useful. I have iGo on my Ameo and it is brilliant (cant wait for iGo 8 or MioMap 2008 for the 3d visuals and road names) but it would be even better if I could get warned of upcoming hold ups on the major roads!
Click to expand...
Click to collapse
Hi,
just a question from my side:
I'm currently using igo with my Ameo and I have to wait and wait and wait and wait for the first GPS fix. It takes normaly between 5 and 15 Minutes until the first fix, even if I use the Quick-GPS Tool that comes with the Ameo. After that, everything works fine. How long does it take with your device and igo?
If I use my GNS GPS receiver (http://www.gns-gmbh.com/de/30_5843.php) I need only a few seconds until the first fix. And it supports TMC!!! I've searched a lot around to find another / cheaper solution to use TMC with the integrated GPS receiver, but I didn't find a working solution, so i decided to buy the GNS GPS receiver....
Regards
Andreas
AndreasF said:
Hi,
just a question from my side:
I'm currently using igo with my Ameo and I have to wait and wait and wait and wait for the first GPS fix. It takes normaly between 5 and 15 Minutes until the first fix, even if I use the Quick-GPS Tool that comes with the Ameo. After that, everything works fine. How long does it take with your device and igo?
If I use my GNS GPS receiver (http://www.gns-gmbh.com/de/30_5843.php) I need only a few seconds until the first fix. And it supports TMC!!! I've searched a lot around to find another / cheaper solution to use TMC with the integrated GPS receiver, but I didn't find a working solution, so i decided to buy the GNS GPS receiver....
Regards
Andreas
Click to expand...
Click to collapse
Hi Andreas,
hmm... thank for the link. That would be really the last chance to get TMC working for the ameo.
FYI, I use Mobile Navigator 6 and it fixes the gps signal really quick. I also use the Quick GPS and when I start MN6 the GPS signal fixes within 1 minute.
Greetz,
DAx
AndreasF said:
Hi,
just a question from my side:
I'm currently using igo with my Ameo and I have to wait and wait and wait and wait for the first GPS fix. It takes normaly between 5 and 15 Minutes until the first fix, even if I use the Quick-GPS Tool that comes with the Ameo. After that, everything works fine. How long does it take with your device and igo?
If I use my GNS GPS receiver (http://www.gns-gmbh.com/de/30_5843.php) I need only a few seconds until the first fix. And it supports TMC!!! I've searched a lot around to find another / cheaper solution to use TMC with the integrated GPS receiver, but I didn't find a working solution, so i decided to buy the GNS GPS receiver....
Regards
Andreas
Click to expand...
Click to collapse
Hi Andreas,
can you confirm that the GNS 5843 TMC work on the X7500 with Igo.
Thanks
Gigino
gigino said:
Hi Andreas,
can you confirm that the GNS 5843 TMC work on the X7500 with Igo.
Thanks
Gigino
Click to expand...
Click to collapse
Yes i.e. it works on my T-Mobile (Germany) Ameo with igo,
Cheers
Andreas
AndreasF said:
Yes i.e. it works on my T-Mobile (Germany) Ameo with igo,
Cheers
Andreas
Click to expand...
Click to collapse
Hey Andreas,
sorry to trouble you again but we are using the igo plus and the same gps as you the GNS 5843 but we can get the gps to work but not the TMC everytime we try to connect the TMC the pda just frezzes like the port has a conflict.
We have only been trying this in landscape mode can you tell me in which mode you are using the igo Portrait or Landscape.
Please can you help me in get this to work because I really like the Igo plus more the any anothe navigators.
Thanks
Gigino
Hi Gigino,
hmmmm, strange, for me it works. And yes, I'm using the landscape modus.
Sounds for me, that Igo uses the internal GPS receiver an tries to find a TMC connection on this internal GPS receiver.
Some Ideas from my side:
If you connect the GNS receiver via bluetooth, which serial port do you use? I've configured the bluetooth settings and then the COM-connections (I hope this are the right terms, I'm using a german ROM) with COM1 and secure connection. For instance Mobile Navigator 6 expects the TMC Signal only on COM1 and doesn't accept other ports.
The internal GPS Receiver is connected to Com4 on my system: GPS Settings -> Programms: Com4 and ->Hardware: None, 4800 Baud and -> Access: Automatic.
In a few words: internal GPS receiver on COM4, external GPS Receiver via bluetooth connected to COM1.
Do you have / use the test software from GNS to test, if youre GPS receiver is ok? You can download it on their page.
Last hint: Sometimes (Mobile Navigator6: every time!) you have to start the Navigator software twice to get a connection to the GNS 5843. It's a known bug for this receiver
Hope all this helps, otherwise contact me again
Regards Andreas
AndreasF said:
Hi Gigino,
hmmmm, strange, for me it works. And yes, I'm using the landscape modus.
Sounds for me, that Igo uses the internal GPS receiver an tries to find a TMC connection on this internal GPS receiver.
Some Ideas from my side:
If you connect the GNS receiver via bluetooth, which serial port do you use? I've configured the bluetooth settings and then the COM-connections (I hope this are the right terms, I'm using a german ROM) with COM1 and secure connection. For instance Mobile Navigator 6 expects the TMC Signal only on COM1 and doesn't accept other ports.
The internal GPS Receiver is connected to Com4 on my system: GPS Settings -> Programms: Com4 and ->Hardware: None, 4800 Baud and -> Access: Automatic.
In a few words: internal GPS receiver on COM4, external GPS Receiver via bluetooth connected to COM1.
Do you have / use the test software from GNS to test, if youre GPS receiver is ok? You can download it on their page.
Last hint: Sometimes (Mobile Navigator6: every time!) you have to start the Navigator software twice to get a connection to the GNS 5843. It's a known bug for this receiver
Hope all this helps, otherwise contact me again
Regards Andreas
Click to expand...
Click to collapse
Hey Andreas,
thanks for your help I well try again over this weekend.
They is another problem that I have and I've tryed everything but cannot resolve it.
I use the Igo Plus in landscape mode when I'm using the map and I get a reminder or a call the screen revertes to portrait mode and after accept the call or dismissing the reminder all the buttons in the Igo software goes all funny.
Do you have the same problem or have you find a way to correct this problem.
Thanks
Gigino
Ah I have this problem if the keyboard is attached but not if it isnt. What happens is that for some wierd reason the screen gets INVERTED! If you imagine where the button should be if it were upside down you can click it! Most odd!
adamelphick said:
Ah I have this problem if the keyboard is attached but not if it isnt. What happens is that for some wierd reason the screen gets INVERTED! If you imagine where the button should be if it were upside down you can click it! Most odd!
Click to expand...
Click to collapse
Hi,
I can confirm this also, the screen is inverted meens, that it looks ok, but you you have to touch it in an inverted way. I.e. the button is on the left upper corner of the screen, but you to click in the right lower area. Thats really strange. I've have the feeling, that this happens very often, if you use the Map view instead of the cockpit view.
@ gigino: I use the ameo with a brodit mount without the keyboard, so I don't have this problem.
In my last message is a little mistake, you have to switch OFF (and not ON) the automatic access in the GPS settings.
Regards
Andreas