Hi,
This is my first post so please be easy on me
I am an ICT Engineer and I am having problems with one of my customers HTC Kaiser (re-badged as Orange TyTN II).
He has an THB Bury cradle. The Kaiser has TomTom installed (Orginal disc version 6 navigator), but when the phone is docked in the cradle it goes to Cra Kit profilr and he gets no sound from TomTom.
I have changed the profile, but still no sound from TomTom. I have checked the cradle it it works fine apart no sound for sat nav.
I have searched for hours on loads of forums to find a fix for this i.e. new ROM from Orange or patch from THB, but can't find anything.
Has anyone else had this problem and is there a fix i.e. registry alternation.
Is there anything within the TomTom settings for this.
It might be that this is the way it will work, afterall you do not want the TomTom coming out over the audio of the telephone call.
Thanks for the reply.
We used to use the Orange SPV M2000 (HTC BlueAngel) with TomTom using the same hands free kit (different cradle obviously) and never had a problem. The sat nav audio would work as normal, but when a call came in the sat nav would cut out until the call had finished.
I have have been through the TomTom settings (very limited) and cannot see anyway of changing the audio on it.
It seems more like a HTC Kaiser problem rather than TomTom or the cradle, because it worked fine with a BlueAngle.
Just found this on a THB Bury re-sellers site: -
"Please note: When the Phone is put into the cradle, the Phone will immediately go into car kit profile, which means the external speaker will be disabled [loss of sound for the Sat Nav directions]"
Is the registry hack to stop this happening?
Have you tried using the tomtom and checking there is audio working ok without putting it in the cradle?
Yep. TomTom works absolutly fine out of the cradle. I have even bought a new cradle to check if the original cradle was defect, but still no sound.
To summarise: -
TomTom audio working fine out of THB Bury HFK
TomTom stops working when in THB Bury HFK (enters Car Kit Profle)
Could you not move the handsfree cradle to maybe a vent mount solution so that when you are in the car you can view the TomTom directions instead of hearing them?
Personally I would find yor situation ideal as I hate SatNav voice commands and prefer to navigate from the map.
I got a response from THB Bury about this problem:
"Dear Alistair, many thanks for your enquiry regarding our Bury product range.
The Navigationcommand didn´t run over the carkit, because the Navigationsoftware got no software for muting.
Best regards
Dean Taylor
--Bury-Infoline-- "
Not really what I needed so.....
Does anyone know either how to doctor the USB connector so that it doesn't cause the phone to switch to 'car mode' OR a registry/software fix which stops the TnTY/Stellar from muting its internal speaker when in 'Car' mode?
Failing that I need a new car kit which, holds the phone, charges it, provides hands free phone service, allows TT6 audio instructions through and doesn't blow the USB port. Just like the THB Bury 'Universal' kit should do.
Any recommendations? Alistair
Related
HI everyone, been reading th eforum for a while now, and the questions if car kits keeps comming up.
I managed to find one today online, looks ok, but needs professional installation.
here is the link ( and no, before you ask, I am nothing to do with the company, just came across it while looking for accessories for my new XDA)
http://www.directmobileaccessories.com/product_info.php/cPath/161_162/products_id/585
hope it's good!
Thanks
John
Product not found!
Sorry about that, if you look under O2 in the same page you will see it. Ever so sorry about that.
damn links!!
This is the O2 xda car kit
I ordered the kit from directmobileaccesories.com and it arrived yesterday, it is an O2 boxed xda car kit.
Everything works fine - except - I removed my old Nokia 9110 car kit which had a radio mute kit that feeds the phone through the car speakers, and tried to connect the radio mute from the O2 kit to the radio mute lead used by the Nokia car kit. When I place the xda in the cradle it immediately cuts over from the radio to the phone, even before the phone part of the xda is activated.
I have a radio mute on the steering console so I have temporarily disconnected the mute lead and fitted the speaker that came with the xda car kit.
Any suggestions why the radio mute cuts over straight away ?
Try making a call
Hi,
I have seen the same behaviour, it looks like the mute works reversed. If you make a call the radio will swotch on.
If this is your problem it should be easy to fix by using a small relay or something similiar.
Francois
the problem has resolved itself
the problem I had with the radio muting all the time has resolved itself, it now works perfectly.
I recently got an AT&T Tilt and am looking for a good, reliable bluetooth kit for my 2005 Toyota 4Runner. I found two different kits that look good, and I want to know if any of you have any experience with these:
Parrot 3200 LS Color:
http://reviews.cnet.com/car-audio/parrot-3200-ls-color/4505-3425_7-32138918.html
THB Bury Comfort Compact 9060:
http://yourwirelesssource.com/buy/accessories/cat/1005/accessory/301883?eventGroup=4&eventPage=1
I just want a good kit that wires into the vehicle and uses the car speakers. Any suggestions on other kits are welcome.
Thank You for the help.
Motorola T605. I'm looking at getting that one now and it looks pretty good. I would link to it, but I'm tired, I've been drinking, and I will be asleep in about 117 seconds from now.
www.safewireless.com
Visit www.safewireless.com and check out the car kit demos on the parrot car kits, this will give you a real feel of the kits. Also they have car kit and harness bundles.
If you have any questions, call them and they will tell you evrything you need to know about Parrot car kits.
greenhead said:
I recently got an AT&T Tilt and am looking for a good, reliable bluetooth kit for my 2005 Toyota 4Runner. I found two different kits that look good, and I want to know if any of you have any experience with these:
Parrot 3200 LS Color:
http://reviews.cnet.com/car-audio/parrot-3200-ls-color/4505-3425_7-32138918.html
THB Bury Comfort Compact 9060:
http://yourwirelesssource.com/buy/accessories/cat/1005/accessory/301883?eventGroup=4&eventPage=1
I just want a good kit that wires into the vehicle and uses the car speakers. Any suggestions on other kits are welcome.
Thank You for the help.
Click to expand...
Click to collapse
I got this last night and its great http://forum.xda-developers.com/showthread.php?t=390945
I was specifically looking for a wire free audio streaming soloution, but the hands free profile stuff works great.
Hi I have used a parrot ck3100 for years now (for the last 4 phones I have had) cant fault it updated the software through Bluetooth each time and still working today, easiest way I found to fix in to the car to mute radio and put call through speakers is to get a conversion lead form a dealer, (£20.00 ish in the uk) this fits between your radio and the car kit.
I have the parrot kit installed in my subaru. my tilt and my wifes samsung are paired to it and the friggin thing works great. i suggestthat if you have the original radio in your veichle, then get the wiring adaptor for that car. this way no wires have to be cut. if needed, i will post a link here for the website were i got the adaptor for my subaru.
I also have the CK3100. It USUALLY works great, but I have had some issues w/ my Tilt. Occaisionally, it will phantom dial when I first start the vehicle. When that particular glitch occurs, it will continue to randomly mute the stereo for a couple of seconds every few minutes.
A recent firmware update to the Parrot seemed to fix the problem, but it started again after a week. I just got a new Tilt (warranty replacement) and haven't had the problem again, but it's only been a couple of days. It was a week after that firmware update before the issue recurred.
If you go w/ the Parrot, I highly recommend www.parrotkits.com for a wiring harness. I'll say that I did not like the way it functioned in my Nissan Titan due to the way the factory stereo is configured - it caused a loud pop in the amp when switching between the stereo and phone. In most other vehicles, this should not be a problem. It sure did make the install a breeze.
Dan
Hi,
my Diamond works ok with my Parrot bluetooth car kit. The only thing that is really anoying me, it takes veeeery long until the Diamond has established the connection to the car kit. I have to drive for several minutes! until the Diamond connects. Before I had a Sony Ericcson phone where I did not have this problem.
Any ideas? Is this just because the Diamond is a WM phone?? Or is there a way to improve this?
Thanks
I use my diamond with a Parrot CK3300 - not sure if that is the same as yours. I only use it for handsfree since I use the Diamond's own GPS receiver. I don't have this problem - it picks up and pairs within seconds.
Have you flashed the Parrot with the latest software? I found that improved performance considerably - automatic update of contacts, user name on screen rather than phone name etc.
I use the Parrot CK3100 and the pick is almost instant; I've barely got in the car and started it up and the Parrot has picked up my Diamond. It was just as quick on my Hermes device too.
I also have a CK3100 and here's somewhat the same problem.
It connects in a few seconds, and it's usable.
But the synchronisation takes forever.....
That doesn't bother me, becouse I'm quite long in my car when driving to work...
But:
The phonebook in my CK3100 starts with the numbers wich are saved on the SIMcard.
All my friends are saved on the internal memory of the TD.
So if i want to call 'Anouk': I press 'A' on the CK3100.
It starts with the 'A' from the SIMcard.
Then I have to use the turning wheel, to scroll BACKwards to "anouk'!
So this takes a lot of time.... and is very, very unpracticle.
Someone a solution for this?
As I said before flashing the latest software onto my Parrot made it much better for syncing contacts. But I only need do it once - after that it only checks for changes. It should not be syncing each time because the Parrot should store the contacts itself.
Yep, just check the Parrot website to see what the latest update is for your particular BT device and try applying it. Saying that, I've not updated my one from factory.
Unfortunately I was not able to update my Parrot so far. I have only a CK3000 Evolution, Firmware version 5.08C. I guess I would need this special serial flash cable...
@ swissly
i have the same problems fw months ago. you have to delete the partnership's on your CK3000. press the red and the green button for more the 3 sec. (Erasing in progress) if this is done you can create a new partnership. hope that helps.
\\yoshi
swissly said:
Hi,
my Diamond works ok with my Parrot bluetooth car kit. The only thing that is really anoying me, it takes veeeery long until the Diamond has established the connection to the car kit. I have to drive for several minutes! until the Diamond connects. Before I had a Sony Ericcson phone where I did not have this problem.
Any ideas? Is this just because the Diamond is a WM phone?? Or is there a way to improve this?
Thanks
Click to expand...
Click to collapse
Hello
For all of you who have a Parrot Bluetooth car kit listen up:
When you use any phone with any Parrot Bluetooth car kits please go to the Parrot support website to flash your car kit - http://www.parrot.com/uk/support/onlinehelpguides
This will update the device with the latest firmware and as Parrot continuly add new phones to their list it is must. I did it as soon as my HTC Diamond arrived and finds it pairs/syncs within 1 - 3 seconds of switching the car on. FYI I have a Parrot MK6100 device, which supports A2DP Bluetooth audio and is mint. Previous to this I had an SPV M700 and a Parrot CK3100-something, but same thing - update it and you will find it solves the problem(s).
- PLEASE HOWEVER READ THE INSTRUCTIONS ON FLASHING - IT AIN'T HARD BUT READ IT ANYWAY!!! -
Please correct me if I'm wrong, but I still think I CANNOT UPDATE my Parrot CK3000 Evolution WITHOUT THE PARROT SERIAL CABLE!
swissly said:
Please correct me if I'm wrong, but I still think I CANNOT UPDATE my Parrot CK3000 Evolution WITHOUT THE PARROT SERIAL CABLE!
Click to expand...
Click to collapse
You are correct AFAIK. Most other Parrots can be updated easily using bluetooth, but not that one. Probably why it was cheaper than the others.
I have experienced few irritating problems with my Diamond when used in my Seat Leon 2008's stock head unit via bluetooth:
1. Phonebook is displayed always and I can call phones from there which is OK, however "Incoming Calls", "Outgoing Calls" and "Missed Calls" are not working always: sometimes I have those lists filled with the corresponding entries, sometimes all three lists are empty.
2. When I am running iGO8, the bluetooth connection gets connected and disconnected each 5 minutes or so.
3. The headset volume is really low. I didn't have that problem with my Sony Ericsson phones before.
Does anyone have any of those problems and know a solution for them?
Only thing i can say. Stock seat bluetooth is terrible. My brother has orderd a new seat and the dealer advised to choose for the pioneer mounted radio because of the known problems with the seat unit and the bluetooth functions of it.
try posting in the Accesories section, u might get more help.
marco899 said:
Only thing i can say. Stock seat bluetooth is terrible. My brother has orderd a new seat and the dealer advised to choose for the pioneer mounted radio because of the known problems with the seat unit and the bluetooth functions of it.
Click to expand...
Click to collapse
Pioneer isn't that good either, I had the Pioneer radio with Bluetooth and I couldn't get it running with my previous phone Trinity P3600 and with my Diamond it didn't work either.
Willem
I have used the stock head unit previously with simple mobile phones and it has always worked perfectly and I was very happy with the bluetooth implementation in Seat. So, I think the problem is not in the head unit (i.e. an accessory problem) but lies somewhere in the "phonebook through bluetooth" implementation in the Diamond.
Hello,
I have the same problem. I have a Skoda Octavia II (2007) with built-in bluetooth and a Diamond (ROM 2.03).
I use the iGO8, and it works fine, but the bluetooth connects and disconnects randomly in all ~5 minutes. When I shut down the iGO8 or when it runs on the background, the bluetooth works perfectly, when it runs in the foreground, the bluetooth disconnects again...
Who knows wat is this problem? Should I try a new ROM? A new radio version? A new iGO version?
CyberGene: Have you a solution for this problem? Or you use a different iGO8 or a different navi software?
Thanks,
DuckHead_
Unfortunately I didn't find any solution to the problem. To be honest, I am currently using a SonyEricsson phone and the Diamond is used by my girlfriend. We are still using iGo from within the Diamond but with no Bluetooth activated.
Thank you for the quick answer.
Why don't you just take your car into a car audio place and get them to check it out for you
I thought it so that the problem with Diamond. The BT does not work only if running the iGO...
This is a problem for which I've spent a lot of time.
I purchased two THB Bury HF kits for my cars and the cradles for them.
Later I found out that the navigation commands (TomTom) are not audible through the HF kit.
However, I purchased P3300 (Artemis?) to my wife and Bury cradle for it. It does its work very well. Both calls and navigation commands work through the HF kit.
I've written several e-mails to THB Bury and asked their opinion why my wife's phone if working OK with Bury's HF (the navigation commands) and mine is not.
Today I got fed up because they didn't reply to my e-mails and I gave them a phone call.
They explained me that Kaiser is not able to mute the HF signal while giving the navigation commands but P3300 is able to do that because "it's an older phone model". I dunno whether they told me the truth so therefore I'd like to ask from all of you software wizards:
Is there a software update/upgrade for Kaiser which would enable to mute the HF signal before giving the navigation command? Any help will be highly appreciated!
Moved as not ROM Development.