My TyTN II isn't being detected by on my PC.. I've tried uninstalling everything and reinstalling everything, but no luck.
Where can I find USB drivers for the TyTN II? I don't recall installing it when I first got my phone, but someone suggested it, but I can't find it anywhere.
DVS_WiNdz said:
My TyTN II isn't being detected by on my PC.. I've tried uninstalling everything and reinstalling everything, but no luck.
Where can I find USB drivers for the TyTN II? I don't recall installing it when I first got my phone, but someone suggested it, but I can't find it anywhere.
Click to expand...
Click to collapse
Are you connected via a non-powered USB hub as this can sometimes cause a problem.
Have you tried a different USB cable? I spent a day trying to resolve the same problem on my Universal a couple of years back, only to find the cable was at fault.
EDIT: Did find one other thing a few months back. I installed one of those business card scanners to my laptop and found that whenever it was plugged in, my phone was no longer recognised.. Seems the scanner was pulling all the available USB power for itself.
I've tried 3 different cables on 3 different computers
I'm not using a USB hub..
Did you try changing the advanced settings for the USB-PC connection? I have had that, when I uncheck that box all is good.
Start->settings->connections->USB to PC-> uncheck Enable advanced network functionality
HTH
DVS_WiNdz said:
My TyTN II isn't being detected by on my PC.. I've tried uninstalling everything and reinstalling everything, but no luck.
Where can I find USB drivers for the TyTN II? I don't recall installing it when I first got my phone, but someone suggested it, but I can't find it anywhere.
Click to expand...
Click to collapse
I know this may sound stupid but you are using Activesync aren't you?
I just ask this as you have not mentioned it. A WM device will not be just recognised as a USB device like a printer or other peripheral.
maherb said:
Did you try changing the advanced settings for the USB-PC connection? I have had that, when I uncheck that box all is good.
Start->settings->connections->USB to PC-> uncheck Enable advanced network functionality
HTH
Click to expand...
Click to collapse
Tried that.. didn't work also.. do you remember if you had to install USB drivers for your TyTN II when you first got it? cause I don't remember..
Farsquidge said:
I know this may sound stupid but you are using Activesync aren't you?
I just ask this as you have not mentioned it. A WM device will not be just recognised as a USB device like a printer or other peripheral.
Click to expand...
Click to collapse
Yes I'm using activesync.
DVS_WiNdz said:
Yes I'm using activesync.
Click to expand...
Click to collapse
If you have tried it with three different PC's then it does sound as if the port on the phone may be at fault.
One last question, did it work before at all?
Anyone else with any ideas
Farsquidge said:
If you have tried it with three different PC's then it does sound as if the port on the phone may be at fault.
One last question, did it work before at all?
Anyone else with any ideas
Click to expand...
Click to collapse
Yes I've been using it for 4 months and had no problems. The port on my phone works, I've been using my headset and it charges when I plug it into my PC.
DVS_WiNdz said:
Yes I've been using it for 4 months and had no problems. The port on my phone works, I've been using my headset and it charges when I plug it into my PC.
Click to expand...
Click to collapse
Take a magnifier and look at the port under a good light. See if everything looks OK.
Also check another thread close to this one regarding battery drain whilst connected. Could be that you have a damaged port and it shows different symptoms to theirs.
Someone on that thread says it costs $80 for a repair but hang about a few days, someone may come up with a better answer for you.
Hope you get it sorted.
Farsquidge said:
Take a magnifier and look at the port under a good light. See if everything looks OK.
Also check another thread close to this one regarding battery drain whilst connected. Could be that you have a damaged port and it shows different symptoms to theirs.
Someone on that thread says it costs $80 for a repair but hang about a few days, someone may come up with a better answer for you.
Hope you get it sorted.
Click to expand...
Click to collapse
Port looks fine.. but my batteries draining.. This started 2 weeks ago.. and I've been charging fine.
No I do not remember if I installed drivers or not ... sorry. Try using bluetooth connection to sync. if all fails. I have had that with my old P910
I really think there is something going on here - I am starting to see loads of threads relating to this.
I am also having problems syncing suddenly. Started about 2 weeks ago. I have dual boot on my laptop - vista/XP and my Kaiser wont sync with either anymore.
It seemed to be charging fine up until yesterday when I again suddenly couldnt charge it from anything other than the official charger. Before that I had charged it on pretty much anything - my proporta power supply, sync cable attached to a USB plug, blackberry charger.
If its hardware then there is obviously a weakness with the USB connection as so many people seem to be experiencing similar things.
Maybe time to contact HTC although after their response to the video drivers, wouldnt hold up much hope.
chrisnash said:
I really think there is something going on here - I am starting to see loads of threads relating to this.
I am also having problems syncing suddenly. Started about 2 weeks ago. I have dual boot on my laptop - vista/XP and my Kaiser wont sync with either anymore.
It seemed to be charging fine up until yesterday when I again suddenly couldnt charge it from anything other than the official charger. Before that I had charged it on pretty much anything - my proporta power supply, sync cable attached to a USB plug, blackberry charger.
If its hardware then there is obviously a weakness with the USB connection as so many people seem to be experiencing similar things.
Maybe time to contact HTC although after their response to the video drivers, wouldnt hold up much hope.
Click to expand...
Click to collapse
Yep, crishnash, I think you are seeing the same as I am..
chrisnash said:
I really think there is something going on here - I am starting to see loads of threads relating to this.
I am also having problems syncing suddenly. Started about 2 weeks ago. I have dual boot on my laptop - vista/XP and my Kaiser wont sync with either anymore.
It seemed to be charging fine up until yesterday when I again suddenly couldnt charge it from anything other than the official charger. Before that I had charged it on pretty much anything - my proporta power supply, sync cable attached to a USB plug, blackberry charger.
If its hardware then there is obviously a weakness with the USB connection as so many people seem to be experiencing similar things.
Maybe time to contact HTC although after their response to the video drivers, wouldnt hold up much hope.
Click to expand...
Click to collapse
hmm.. right now I can still charge through the computer, I hope it doesn't come to that, cause I charge using computers very frequently.
Now linked to...
http://forum.xda-developers.com/showthread.php?t=362679
If you would like to contribute.
May seem silly to ask but have ou tried rebooting your computer and soft resetting your phone? (I have to soft reset mine about once every other day or this same thing happens to me.
ajmoncrief said:
May seem silly to ask but have ou tried rebooting your computer and soft resetting your phone? (I have to soft reset mine about once every other day or this same thing happens to me.
Click to expand...
Click to collapse
I've tried that so many times, I don't even remember how many.
ajmoncrief said:
May seem silly to ask but have ou tried rebooting your computer and soft resetting your phone? (I have to soft reset mine about once every other day or this same thing happens to me.
Click to expand...
Click to collapse
Yep done the standard stuff with people for the last 8 months. Whereas it may or may not be attributable with this problem... I am trying to collate data.
Trouble is, a trend is starting to occur with damaged (PHYSICALLY) mini-USB ports that are not done by the old 'Sticking the stylus in the port'.
There is a trend of failure when using a STANDARD mini-usb connector in this port. It is a non-standard connection so if failure occurs it needs to be rectified.
Hey, I aint doin a lawsuit, I am just working on a free refurb and advising HTC to modify AS IT SHOULD BE!!!
Just for grins, try to connect via IR or Bluetooth ...
Related
laptop no longer recognizes tilt or tytn; changed usb cables; rebooted both devices and laptop; no go..
mssg I get is "one of the usb devices attached to this computer has malfunctioned. and windows does not recognize it"; any suggestions; cannot sunc nor tether via ISharing.
tia
a in yul said:
laptop no longer recognizes tilt or tytn; changed usb cables; rebooted both devices and laptop; no go..
mssg I get is "one of the usb devices attached to this computer has malfunctioned. and windows does not recognize it"; any suggestions; cannot sunc nor tether via ISharing.
tia
Click to expand...
Click to collapse
Hi
First of all try to reinstall Microsoft ActiveSync, than in the ActiveSync options, in your device, be sure that in "Connections..." setting "Synchronize all PC by this connection" is checked and below "USB" showed!
Otherwise, if your device, when connected to the PC, also doesn't charge (if you have this option enebled on your PDA!) there is some problem on your PC settings concerning the USB! Try to connect to someother PC to test it!
Ciao
thx...
@[email protected] said:
Hi
First of all try to reinstall Microsoft ActiveSync, than in the ActiveSync options, in your device, be sure that in "Connections..." setting "Synchronize all PC by this connection" is checked and below "USB" showed!
Otherwise, if your device, when connected to the PC, also doesn't charge (if you have this option enebled on your PDA!) there is some problem on your PC settings concerning the USB! Try to connect to someother PC to test it!
Ciao
Click to expand...
Click to collapse
hello there, first n foremost thanks for your input!
Before trying out your possible solution i tried to connect and for some reason i was able to connect via the device today...??!!
i really dont know why, but will try your soln if this situation reocurrs.
NB: this happenned to me twice in the last 3-4 months, n i never figured out the cause ??
any other advice or ideas gratefully accepted.;
its probably the same as me and loads of other people - the pins have bent on your usb connector - probably caused by using non standard chargers and usb leads. Its been widely reported. The non-standard leads have too much space around them when plugged in and wiggle causing the connector on the tytn II to bend. Try using the lead which came in the box and see if it helps. and try using the charger that came with it too.
Can bent pins be fixed?
Hello -- I'm one of those people with a non-recognition problem. Is it possible to fix the bent pins? My problem seems to have begun around the time I lost my original USB cable. Now, all the cables I have -- ones that have been specifically sold to work with my HTC Tilt -- have the symmetrical, sort-of-trapezoidal mini-usb connection, rather than the rectangle-with-one-corner-cut-off shape of the original cable. I should say these cables do charge my device, but none of my computers recognizes it as a USB device.
Help?
Thank you,
J. Georgia
bent pins continued
I should add that the charging cable that originally came with my phone has the same connector shape, so I'm not sure what's going on.
USB Device not recognised
This is known to happen at times win Windows, and not just for the TYTN2 but a myriad of devices.
The fastest fix for this:
Reboot ur PC/ Laptop.
If this Doesn't help - Then add in a reboot for the TYTN 2 also.
The problem will go away for some time.
I know its annoying, but this is way faster than troubleshooting for contacting MicroShaft Support.
axeman said:
This is known to happen at times win Windows, and not just for the TYTN2 but a myriad of devices.
The fastest fix for this:
Reboot ur PC/ Laptop.
If this Doesn't help - Then add in a reboot for the TYTN 2 also.
The problem will go away for some time.
I know its annoying, but this is way faster than troubleshooting for contacting MicroShaft Support.
Click to expand...
Click to collapse
Unfortunately this is no soution for me. I seem to have this problem as well, since about two weeks.
I use two notebooks (Dell & Acer) and both do not show any activity when connecting my Kaiser to the original USB cable. The device is not even switched on when I connect it, nor does this happen when I connect it to the (original) cable in my car, which did work before.
Charging works fine, both in the car and when connected to both notebooks, but no Sync at all.
I have tried another USB-cable with the same result, so I suspect some hardware-problem causing me to be unable to copy files between my notebook and my phone and worse, rendering me unable to flash a new ROM onto it.
Who knows what to do next?
I am mystified, too. USB Charging and audio connections work. I have rebooted my computer and done a soft reset on my phone several times, to no effect. I uninstalled and reinstalled Windows Mobile Device Center. Still nothing at all via USB. Once, yesterday, I somehow got a Bluetooth connection long enough to sync, but haven't been able to since then. Even then, Windows Media and AudibleManager couldn't see the phone. The really weird thing is, I can see the phone connection in my Bluetooth manager, but even with all the proper boxes checked, I can't sync. When I try from my device, I get an empty progress box which disappears after a fraction of a second. When I try from my computer, it says the device is not connected, but doesn't give me any option to connect.
Would a hard reset help?
If so, would returning an unlocked AT&T Tilt to factory defaults lock it back up? And what do I do if it does?
Please help!
J. Georgia
I have had similar problems with my touch pro in the past, even bluetooth internet sharing eventually gave up the ghost.
I tried a myriad of leads and then eventually reinstalled active sync- which did the trick.
USB sync not working
[email protected] said:
I am mystified, too. USB Charging and audio connections work. I have rebooted my computer and done a soft reset on my phone several times, to no effect. I uninstalled and reinstalled Windows Mobile Device Center. Still nothing at all via USB. Once, yesterday, I somehow got a Bluetooth connection long enough to sync, but haven't been able to since then. Even then, Windows Media and AudibleManager couldn't see the phone. The really weird thing is, I can see the phone connection in my Bluetooth manager, but even with all the proper boxes checked, I can't sync. When I try from my device, I get an empty progress box which disappears after a fraction of a second. When I try from my computer, it says the device is not connected, but doesn't give me any option to connect.
Would a hard reset help?
If so, would returning an unlocked AT&T Tilt to factory defaults lock it back up? And what do I do if it does?
Please help!
J. Georgia
Click to expand...
Click to collapse
I've had the same problem with my first Tilt. There's multiple threads that detail this known problem. Some seem to be due to bent pins, some are general hardware failures (possibly the USB controller). There are some HardSPL images out there that have a "force usb" option enabled. This never worked for me, but it might be worth a shot for you.
...a word of warning....
If you end up reflashing your phone (via MicroSD) and the flash goes bad, you may be stuck, as many of the solutions for repairing a bad flash require you to USB sync. My first Tilt was a victim of this after a bad stock ROM flash that left my device without audio, and unable to flash via MicroSD.
replace usb board
you need to replace your usb board. It will run you less than $10 if you do it yourself. you can get the board on ebay
really? 4 years later?
When i connect my device to usb, nothing happens.
I looked up the forum for solutions, but was unable to find them.
It shows nothing in network connections, nothing in device manager, en activesyc shows nothing at all.
I tried the following:
- Other USB cable/port
- Reinstall activesync or use older version.
- Uncheked advanced networking in my device.
- Turned off firewall
I cant think of any other solutions at this time, maybe someone can help me.
(sorry for my bad English, i'm Dutch)
Ciao,
did you try to remove your older connection from your telephone? I mean programs -> system tools -> activesync -> menu -> options -> delete existing connections.
This works for me whenever i have some connection problems.
No luck =(
Still the same
No one has any idea?
Reboot the PC. Make sure you check Device Manager for any issues. Maybe disconnect all USB peripherals and then try the phone first. Did you try a different machine (PC)?
kimtyson said:
Reboot the PC. Make sure you check Device Manager for any issues. Maybe disconnect all USB peripherals and then try the phone first. Did you try a different machine (PC)?
Click to expand...
Click to collapse
yes, i tried 3 machines.
But the problem is, the devices is reconized by none of them
What is the operating system of your pc´s
Windows XP sp3???
If so there are some issues that relates to sp3 but i dont know any resolution for it thou.
Nope, fully updated SP2
The HTC proprietary extUSB connector on the bottom of the TyTN II has been known to fail in a few cases (if you search in this forum there are many posts about it). When you plug in the charger or wired headphones do these work fully? Does your battery charge when connected to a PCs USB port? Not that these are 100% foolproof tests because different pins are used for the USB signal connection. What changes did you make or incidents occurred before this problem occurred e.g. started using a different charging cradle etc? Have you inspected the connector for damage and tried the original HTC cable?
Flying Kiwi said:
The HTC proprietary extUSB connector on the bottom of the TyTN II has been known to fail in a few cases (if you search in this forum there are many posts about it). When you plug in the charger or wired headphones do these work fully? Does your battery charge when connected to a PCs USB port? Not that these are 100% foolproof tests because different pins are used for the USB signal connection. What changes did you make or incidents occurred before this problem occurred e.g. started using a different charging cradle etc? Have you inspected the connector for damage and tried the original HTC cable?
Click to expand...
Click to collapse
The battery still charges via USB (via my pc), i used a charger in my car.
This is a USBport in the car, difficult to explain.
http://cdn.overstock.com/images/products/L10369942.jpg
I can't tell you of my headphone works, because i lost it.
I can't dectect any damage to my USB port.
Update:
I've been looking at my USB port on mt PDA, and did a little bending, now when i connect my device, the screen flips to horizontal view.
So i guess the problem has to do with the USB connector after all.
Upd: OMG :O it keeps flipping from horizontal to vertical, even when it's not plugged in.
addict1337 said:
i used a charger in my car.
This is a USBport in the car, difficult to explain.
Click to expand...
Click to collapse
Be careful about using just any old car charger system. If you search this forum you'll see that there was one model which could damage the TyTN II due to overloading the UBS port on it (something to do with reverse flow under periods of heavy electrical load). I believe that model was subsequently modified to prevent this problem but it doesn't mean other car chargers with the same affliction wont arrive on the scene. Maybe it's time to hard reset the device and if it still plays up, return it to the supplier for a warranty claim.
Flying Kiwi said:
Be careful about using just any old car charger system. If you search this forum you'll see that there was one model which could damage the TyTN II due to overloading the UBS port on it (something to do with reverse flow under periods of heavy electrical load). I believe that model was subsequently modified to prevent this problem but it doesn't mean other car chargers with the same affliction wont arrive on the scene. Maybe it's time to hard reset the device and if it still plays up, return it to the supplier for a warranty claim.
Click to expand...
Click to collapse
=(
I have insurance on my phone.
Maybe i'll contact them then.
Thanks for the help!
Hello everyone,
I'm having a problem with my Diamond. When I attach it to a USB port nothing happens. No 'hardware found sound' or what so ever.
I tried several other pc's with no result. It does charge when it is connected and the phone asks whether it needs to be in USB mass storage mode or in Active sync mode. I havent found anyone with the same problem so I'm afraid it is a hardware failure?
I tried:
-Soft/Hard reset
-Several computers/usb ports
-Disable Advanced Network capabilities
Does anyone have some tips that I haven't tried already that could help me out?
Thanks for your time!!
Disable Advanced Network capabilities under USB->PC in your Settings, that should do it.
I tried that also. With no result yet. Any other tips maybe?
First, check your cable for any marks that resemble rabbit bite marks or alligator bite marks.
No, seriously, check the points where the cable goes into the plugs for any obvious signs of damage, then check the cable itself.
Maybe, try using a different cable, if that doesn't work your Diamond most likely has a problem. If the different cable works, your cable is a goner.
Although I think there's quite a small chance that that's it, it's worth trying, right?
Use the 6.1 version of the Windows Mobile Device Center under Vista
Thx for all the tips. I didn't manage to get it working though
When the phone is connected to the charger it asks if I want to use activesync or usb mass storage. A friend of mine has also a diamond and his doesn't ask this. My conclusion is that it is broken
Damn I got this phone as a replacement for my broken K850i from my provider...They will go crazy when they see me again
Hi,
I have the same problem.
My guess is that it all started with a non compatible charger.
When charging it asked for active sync or disk.
After that the problems started, active sync doesn't work anymore.
Sometimes it workes when advanved networking is off.
Tested on different pc's, freshly installed.
Complete factory settings, notting works.
If synchronised by bluetooth it works.
I'm affraid i have to send the phone back for repairs and trow away the bad charger.
I never used a 3rd party charger.
Is there a way to update the firmware via bluetooth?? Because i'm still using the old slow version...
Same problem here. I've used my tomtom USB car charger. Is this a guarante matter, or do i have to pay for the repair?
You may have set the default connection to other than ActiveSync when first seeing the pop-up.
Go to 'Settings' 'Connections' and select 'USB to PC'.
Ensure ActiveSync is selected.
If you want the pop-up to display when the USB is connected (its good when you want to use your internal micro-SD as a memory stick), check the box at the bottom. You can select ActiveSync, Memory or PC Modem from when it appears on connection but when you just ignore it, it will perform whatever default selection you wanted last and then dissappear.
If all else fails perform a hard reset!
I've tried /soft/hard reset. No luck..
Can this be a hardware related fault, or could a ROM flash resolve the problem?
Transfering video files via BT is a pain in the a*s...
i would try a flash before returning it. You can probably dl an official 1.93.xxx.xx from htc and try that. You don't need hard spl and all that for those ROMs.
I have the same problem:
no connection at all from the PC-side. The Diamond comes up with the ActiveSync/Discdrive question and starts charging, but nothing else.
I did use external chargers that also trigger the ActiveSync/Discdrive question.
Update:
Oops, it seems fixed after a soft reset.
Same problem, diamond would not connect to PC.
Solution: Warranty repair---> they changed the motherboard, and everythings is good. Everything was free.
Edit: But now I have a different problem. I connect diamond in to PC, everything is good, but about 30 seconds after, mobile center looses the diamond, and sync won't work. Any solutions?
I have the same problem before. My Diamond USB cannot be recognised by the PC. Took back to repair and now working. But one PC still cannot recognize the diamond. The service centre told me they have reset my unit and when came back, everything has been cleared. I suspected a full reprogram of the ROM.
I have the same problem
I cant have any connection to the PC
so, no solution but the service people
USB Connection ERROR
I have the same problem. No computer seems to be able to connect to my P3700. I tried DL new ROM but I don`t know where my device came from. On HTC site from HK, which is the only one where I found a neutral Diamond with no carrier associated like, Sprint , Telus, or the like, its says The ROM Code can only be updated on HTC Touch Diamond Hong Kong English Version Device
Does anybody have a clue how to find out where my device was originally intended to be marketed? My ROM is 1.93.456.2 WWE dated July-10-2008? Do the the numbers 456.2 mean anything?
Help is highly appreciated!!
change your usb wire..
Epioneer said:
I have the same problem before. My Diamond USB cannot be recognised by the PC. Took back to repair and now working. But one PC still cannot recognize the diamond. The service centre told me they have reset my unit and when came back, everything has been cleared. I suspected a full reprogram of the ROM.
Click to expand...
Click to collapse
I already did. The first few times the problem occured it worked. I have 6 different USB wires and they all cause the problem. When I hook up my HTC Touch, they all work well!?
Won't sync with PC
Hi,
I have the same thing where it won't sync with any PC and i've tried all the "other" fixes and I've sent it to the service people to have a look.
Thing is, because I thought it was an issue with the usb connector I thought I would have a poke around with it myself and i could see one of the prongs looked like it wasn't making contact. To cut a long story short whilst i was trying to fix it the plastic tab in the mini usb connector came out completely
Service people are now saying that I've abused the handset and want to charge me £70 to fix it. Now to be fair, I have made it worse, but in my defense it was only because a fault had occurred that I started to dabble.
I also reported to the service people that the led light under the "end call" button had stopped working completely. This was definiatley not due to miss use.
I'm wondering if this led is on the motherboard like the usb connector is. If so, can i be cheeky and just ask them to fix the led and not the usb? but by default because the m/b would be swapped out then the usb would be fixed anyway?
If you looked at my phone it looks well cared for (which it was!!!) and its not like I've hammered it in anyway.
Anyone have an opinion or know if the led for end call and the usb port are both on the motherboard?
Thanks
hi,
I think my cable or port on my diamond is a little screwed, active sync stopped working just a week after I got the phone.
I posted the problem here:
http://social.microsoft.com/Forums/...c502e361-e0e4-4d26-9ead-7f2680ff160e/?lc=1033
I got Nothing so far. I did all the active sync troubleshooting I could when I noticed that when I charged my phone, the dialog to choose active sync or disk driver shows up!!? As if i plugged it into a pc, also I do plug is into any ANY pc as a Disk Drive, it doesn't work at all.
IOW.. when I connect my phone to *charge* a dialog shows up asking me whether I want Active Sync or Disk Drive as if i connected it to my PC. Nothing happens after that, and it will not connect to active sync or disk drive to ANY Pc (tried multiple pcs).
What could the problem be? Should I try htc tech support?
Please help, this phone is only a month old!
Thanks so much
Gideon
Ok.....I'm not sure what you're trying to say. What's the message you get on your screen when you connect your phone to the pc via activesync?
I'm sorry, I was freaking out just a little while writing that. I rephrased some of it.
I get the same dialog "Active Sync or Disk Drive" when I connect it to my PC, but nothing happens after that, and it doesn't work on any pc at all. And its driving me nuts, to send a file to my phone from my desktop(my main computer) I have to connect it to my laptop via a lan wire, then send the file over there, and send it from the laptop via WiFi to the phone! ! =X
Oh btw, I've also tried other mini USB cables. Same thing.
Thanks so much
Gideon
What version of activesync are you running? Download the latest version from here. Activesync runs on all OS versions from Win 2000 SP4 upto XP SP3. If you have Vista installed on your machine try this link.
Would you be able to paste a screen shot of the error message and the dialog box?
I use the latest 4.5, but that does'nt seem to be the problem.
It doesn't work as a Disk Drive on ANY computer? There isn't any message or error, on the phone I get the dialog "Connect To Pc" dialog, I choose DISK DRIVE but it doesn'nt work, not on MY pc not on ANY PC!! ='( And just nothing happens.
I've given up on active sync, i've read every post here on xda and elsewhere, I simple can't get it working, I don't have active sync on my pc now. On my laptop with *Vista* however, the windows mobile device center manages to connect and sync with my phone via *bluetooth* only
Thanks so much.
Gideon
Take out the memory card from your phone before connecting it to activesync and try again. Tell me what happens.
[email protected] said:
Take out the memory card from your phone before connecting it to activesync and try again. Tell me what happens.
Click to expand...
Click to collapse
You cant take out the diamond's memory, it's build in internal memory m8, not like the touch pro's microsd or anything so he wouldnt be able to try/ do that
I've had active sync problems as well, I normally find it's simply the sh*tti microsoft OS's/ programme's problem & if you re-install or update the active sync prog or windows mobile centre if your using vista, it then see's the diamond again no problems & let's you then set it up correctly, so I'd try all that 1st before you go phoning htc or your carrier to complain m8
Had the exact same problem with my Diamond.
The fix was; return to reseller/change of mainboard in the phone.
A known problem with some Diamonds according to the technician who did the repair.
Humm, I ran into a similar problem with my Diamond when I bought it less then a week ago. Nothing happened when I connected the with the bundled cable though it did work at first. So I took a normal one (from the ps3 controller to be exact) and it worked fine, I've not messed with the bundled cable since.
Solution for me
Hi,
I had this exact problem, wouldn't sync with any PC/laptop tried all the active sync's and tried all the options in there. Also tried multiple cables and still no joy.
This needs sending to HTC for them to fix. Go here:
http://service.europe.htc.com/Tracking.aspx and book it in for repair.
This is a known fault that happens with these phones and they fix it without charge.
However, don't be like me and try and fix it yourself, otherwise you'll be £70 lighter. I thought one of the mini usb prongs wasn't making contact (as it still charged ok) and after messing about the little plastic in the mini usb port came out. HTC said I damaged it and so had to pay for repair. If I had just left it alone they would have fixed it.
Also when they fix it they should load on for you Rom 1.93 which I'm finding is making the phone so much better. Its worth the money I've had to pay just for that TBO its soooo much slicker now.
The reason why this fault has developed (that some people have said) is that some car chargers are delivering too much power for the port especially when plugged into the car charger and then starting your car. I've seen that the normal charger delivers 5 volts and 1 amp so i've bought a car charger that does the same volts/amps from here:
http://www.dealextreme.com/details.dx/sku.688~r.53733725
I've used it once and it hasn't fried my Diamond yet. (it did however come up asking to activesync or usb drive when it was plugged in unlike the standard charger which doesn't prompt at all)
You also buy the official car charger which is more £££
You'll be without your phone for a week at least and you'll have to install your apps on it again.
Hope that helps
Hi,
I know this is an old thread, but thought i would add what i found as google brings this thread up when you search for this issue. I read through the solutions and through i would remove and reinstall mobile device centre. I found it had gone! Dont know why. I didnt uninstall it and havent ran a system restore etc. Anyway i reinstalled it and problem solved I think Bluetooth might have also been interfering.
Hello fellas,
I have a problem with my brand new T813 running the latest official firmware available (Android 7).
Massive storage is not working, my computer running Windows 10 with updated samsung drivers has failed to detect it. The device charges, but I am unable to modify the usb options, regardless the choice MTP always remain.
I have tried with three different cables, all of them work fine with my S7, the computer never detects the device, eventhough it's charging. This means it is not a problem with the device's micro usb port. I have the latest drivers, and I have also tried with all usb ports. None of them seemed to do the trick.
The computer has faulty usb 3 drivers, ever since I have installed Windows 10, the speed is not what used to be with the previous configuration. I have the same drivers, I don't understand what's wrong.
Any help would be appreciated, I have tried most solutions mentioned on this community and they didn't work. I can't flash the device because it is never detected. The problem still persists after a restablishment via the menu.
Download mode shows
QUALCOMM SECURE BOOT: ENABLE (CSB)
FRP LOCK IS OFF
[UPDATE] 06/08 11 AM
Left the device at SAMSUNG ARGENTINA repair shop. Also had to pay 300 pesos (around 20 dollars) as a diagnostic fee, they told me that if I accept the repair cost later on, they would discount the 300 pesos I have paid out of the total price. And if I don't, they will keep the money.
Will update again when Samsung calls me in a couple of days. Maybe this monday, I hope so.
[UPDATE] 06/08 15 PM
I have just received an email from BGH, which is the SAMSUNG ARGENTINA official partner for repairs. They told me that the problem is a FAILURE on the SUB board.
http://www.ebay.com/itm/Micro-USB-C...g-Galaxy-Tab-S2-9-7-034-SM-T813-/322414846816
The good thing, is not that expensive. The bad thing, this tablet hasn't arrived officially to Argentina, and since it has been bough in Chile, the guys at SAMSUNG ARGENTINA had to request an international order replacement, which I have been told it could take some time. But they will eventually get the piece.
Will update again.
What does device manager report when the device is connected?
Sure you don't have ADB enabled? Disable developer settings and try again.
ashyx said:
What does device manager report when the device is connected?
Click to expand...
Click to collapse
Thanks for replying, please refer to first screenshot. No Mass Storage option appears after connecting device. MTP option seems to be forced, i am unable to change it.
The tablet is brand new, but the guy who sold it to me said that it has always been working. He even told me that it has been barely used, and that the device is recognized when connected to an usb audio system. It has been upgraded to 7.0.1 a couple of days ago, maybe that's the problem.
I have just tried with a macbook air and it didn't detect it either, it is only charging. The same computer has detected my S7.
hemp_invader said:
Thanks for replying, please refer to first screenshot. No Mass Storage option appears after connecting device. MTP option seems to be forced, i am unable to change it.
The tablet is brand new, but the guy who sold it to me said that it has always been working. He even told me that it has been barely used, and that the device is recognized when connected to an usb audio system. It has been upgraded to 7.0.1 a couple of days ago, maybe that's the problem.
I have just tried with a macbook air and it didn't detect it either, it is only charging. The same computer has detected my S7.
Click to expand...
Click to collapse
Modern devices don't use mass storage anymore, they use the MTP protocol.
You should see your storage folders pop up in my computer.
fonetyk said:
Sure you don't have ADB enabled? Disable developer settings and try again.
Click to expand...
Click to collapse
Thanks for replying. ADB and USB debugging activated, I have also performed a factory reset and the problem still persists.
Using a microSD didn't help either.
hemp_invader said:
Thanks for replying. ADB and USB debugging activated, I have also performed a factory reset and the problem still persists.
Using a microSD didn't help either.
Click to expand...
Click to collapse
What usb options do you get when swiping down the notification shade?
ashyx said:
What usb options do you get when swiping down the notification shade?
Click to expand...
Click to collapse
There is no notification when I plug in the cable, that is the problem.
hemp_invader said:
There is no notification when I plug in the cable, that is the problem.
Click to expand...
Click to collapse
Does you get any kind of connection in DOWNLOAD mode, can odin see the device?
ashyx said:
Does you get any kind of connection in DOWNLOAD mode, can odin see the device?
Click to expand...
Click to collapse
Sadly nothing at all, the device only charges via usb. This is very confusing because the guy who sold it to me said it was working, but he has also said that he has never plugged it in a computer.
hemp_invader said:
Sadly nothing at all, the device only charges via usb. This is very confusing because the guy who sold it to me said it was working, but he has also said that he has never plugged it in a computer.
Click to expand...
Click to collapse
There are no error codes in device manager when the device is plugged in?
ashyx said:
There are no error codes in device manager when the device is plugged in?
Click to expand...
Click to collapse
Nothing, not even an unknown device. I'm lost here.
hemp_invader said:
Nothing, not even an unknown device. I'm lost here.
Click to expand...
Click to collapse
I think you need to try another pc.
ashyx said:
I think you need to try another pc.
Click to expand...
Click to collapse
I have tried with a mac and nothing has happened, it is only charging. The same computer has detected my s7.
A lot of people seem to have experienced this problem, the remaining solutions I didn't try are using other pc or try cleaning the female port with isopropilic alcohol. Hope it does the trick, otherwise I'm screwed.
I will try at work tomorrow.
ashyx said:
Modern devices don't use mass storage anymore, they use the MTP protocol.
You should see your storage folders pop up in my computer.
Click to expand...
Click to collapse
That is the problem, when I connect the cable nothing happens, it is only charging. Windows doesn't even detects it as an unknown device and neither does mac osx.
I didn't know mass storage is not used anymore, I think my S7 does have it and it works. I will try at work tomorrow.
When the problem appears with different USB cables and in different computers, as in your case, you have to look into the possibility that it may be a hardware issue.
I hope I'm wrong about this, but it sounds like the DATA+ or DATA- pin is damaged in your micro usb socket (pins 2 and 3, see http://pinouts.ru/PortableDevices/micro_usb_pinout.shtml)
fonetyk said:
When the problem appears with different USB cables and in different computers, as in your case, you have to look into the possibility that it may be a hardware issue.
I hope I'm wrong about this, but it sounds like the DATA+ or DATA- pin is damaged in your micro usb socket (pins 2 and 3, see http://pinouts.ru/PortableDevices/micro_usb_pinout.shtml)
Click to expand...
Click to collapse
Yes, I'm afraid it could be a hardware problem. But that would also mean the guy who sold it to me is lying. I have to say it, the device looks like it has been treated with care. However, i have noticed the plastic has worn out a little near the usb port, those black marks could indicate not so much care when plugging or unplugging the cable.
I hope we are both wrong about this. Tomorrow i will know. Fixing this is a pain in the ass, right?
hemp_invader said:
Yes, I'm afraid it could be a hardware problem. But that would also mean the guy who sold it to me is lying. I have to say it, the device looks like it has been treated with care. However, i have noticed the plastic has worn out a little near the usb port, those black marks could indicate not so much care when plugging or unplugging the cable.
I hope we are both wrong about this. Tomorrow i will know. Fixing this is a pain in the ass, right?
Click to expand...
Click to collapse
¡Che! Replacing the microusb receptacle would not only be a pain the ass, but if you make a tiny mistake while soldering or desoldering you can end up with a bricked tablet.
Anyway, let me know what you find out tomorrow, good luck boludo.
fonetyk said:
¡Che! Replacing the microusb receptacle would not only be a pain the ass, but if you make a tiny mistake while soldering or desoldering you can end up with a bricked tablet.
Anyway, let me know what you find out tomorrow, good luck boludo.
Click to expand...
Click to collapse
Actually not too bad as the Micro USB port is a module and can simply be swapped out.
http://m.ebay.com/itm/Micro-USB-Cha...-Tab-S2-9-7-034-SM-T813-SM-T819-/361834576986
ashyx said:
Actually not too bad as the Micro USB port is a module and can simply be swapped out.
http://m.ebay.com/itm/Micro-USB-Cha...-Tab-S2-9-7-034-SM-T813-SM-T819-/361834576986
Click to expand...
Click to collapse
I didn't know this tablet had a modular micro usb port, that's great ! :good: