Activesync Problem (Tytn2) - Tilt, TyTN II, MDA Vario III General

When i connect my device to usb, nothing happens.
I looked up the forum for solutions, but was unable to find them.
It shows nothing in network connections, nothing in device manager, en activesyc shows nothing at all.
I tried the following:
- Other USB cable/port
- Reinstall activesync or use older version.
- Uncheked advanced networking in my device.
- Turned off firewall
I cant think of any other solutions at this time, maybe someone can help me.
(sorry for my bad English, i'm Dutch)

Ciao,
did you try to remove your older connection from your telephone? I mean programs -> system tools -> activesync -> menu -> options -> delete existing connections.
This works for me whenever i have some connection problems.

No luck =(
Still the same

No one has any idea?

Reboot the PC. Make sure you check Device Manager for any issues. Maybe disconnect all USB peripherals and then try the phone first. Did you try a different machine (PC)?

kimtyson said:
Reboot the PC. Make sure you check Device Manager for any issues. Maybe disconnect all USB peripherals and then try the phone first. Did you try a different machine (PC)?
Click to expand...
Click to collapse
yes, i tried 3 machines.
But the problem is, the devices is reconized by none of them

What is the operating system of your pc´s
Windows XP sp3???
If so there are some issues that relates to sp3 but i dont know any resolution for it thou.

Nope, fully updated SP2

The HTC proprietary extUSB connector on the bottom of the TyTN II has been known to fail in a few cases (if you search in this forum there are many posts about it). When you plug in the charger or wired headphones do these work fully? Does your battery charge when connected to a PCs USB port? Not that these are 100% foolproof tests because different pins are used for the USB signal connection. What changes did you make or incidents occurred before this problem occurred e.g. started using a different charging cradle etc? Have you inspected the connector for damage and tried the original HTC cable?

Flying Kiwi said:
The HTC proprietary extUSB connector on the bottom of the TyTN II has been known to fail in a few cases (if you search in this forum there are many posts about it). When you plug in the charger or wired headphones do these work fully? Does your battery charge when connected to a PCs USB port? Not that these are 100% foolproof tests because different pins are used for the USB signal connection. What changes did you make or incidents occurred before this problem occurred e.g. started using a different charging cradle etc? Have you inspected the connector for damage and tried the original HTC cable?
Click to expand...
Click to collapse
The battery still charges via USB (via my pc), i used a charger in my car.
This is a USBport in the car, difficult to explain.
http://cdn.overstock.com/images/products/L10369942.jpg
I can't tell you of my headphone works, because i lost it.
I can't dectect any damage to my USB port.

Update:
I've been looking at my USB port on mt PDA, and did a little bending, now when i connect my device, the screen flips to horizontal view.
So i guess the problem has to do with the USB connector after all.
Upd: OMG :O it keeps flipping from horizontal to vertical, even when it's not plugged in.

addict1337 said:
i used a charger in my car.
This is a USBport in the car, difficult to explain.
Click to expand...
Click to collapse
Be careful about using just any old car charger system. If you search this forum you'll see that there was one model which could damage the TyTN II due to overloading the UBS port on it (something to do with reverse flow under periods of heavy electrical load). I believe that model was subsequently modified to prevent this problem but it doesn't mean other car chargers with the same affliction wont arrive on the scene. Maybe it's time to hard reset the device and if it still plays up, return it to the supplier for a warranty claim.

Flying Kiwi said:
Be careful about using just any old car charger system. If you search this forum you'll see that there was one model which could damage the TyTN II due to overloading the UBS port on it (something to do with reverse flow under periods of heavy electrical load). I believe that model was subsequently modified to prevent this problem but it doesn't mean other car chargers with the same affliction wont arrive on the scene. Maybe it's time to hard reset the device and if it still plays up, return it to the supplier for a warranty claim.
Click to expand...
Click to collapse
=(
I have insurance on my phone.
Maybe i'll contact them then.
Thanks for the help!

Related

Installing w/2.3 multi-instaler and bricked my 8125!

Is there nothing to be done? I had a phone whose touch screen was acting a little off. I used Cingular_Custom_AKU2.3_Combo_Installer_V1 after unlocking the device and it ran fine. When the OS first comes up it requires you to recalibrate your pointer tho, and since my touch screen was fouling up, I couldn't. I called Cingular and got a replacement phone this morning. I turned it on and let it load up its OS. I used ActiveSync and had a successful sync. I unlocked the device. I used Cingular_Custom_AKU2.3_Combo_Installer_V1 again to upgrade the OS. At 40% my computer unexpectedly rebooted. According to the messages that appeared when the computer came back up it was a driver error that caused the reboot (http://oca.microsoft.com/en/response.aspx?SGD=aa971456-440a-4269-a79e-1f07bda35989&SID=10). I tried to run the installer again but it could not find the phone; ActiveSync could not be engaged. I powered the phone off and back on and just get the RGB screen. I tried to reset the device but nothing still. Am I completely screwed??
Do a little reading on interrupted rom flashes. Search for "Bootloader Mode".
You need to flash your device again but this time you have to start in the Bootloader screen (RGB Bars).
Cool thanx. I looked around for people having problems installing ROMs but the only thread I found no one had answered. This gives me something to search for. Appreciate it!
~Anthony
One other tip, from what I've read, it is recommended to make sure your Wizard is connected to one of the MAIN USB ports on your computer, for desktops, these will be on the back of the computer (the ones soldered directly to the motherboard). The ones on the front are usually essentially connected to a USB hub, and not directly to the controller.
On a laptop, all of the ports should be good.
mine did the same thing last night with the 2.3 with cf2. i had chosen option 2 (no bootloader) and my machine rebooted at 40%. Since this has happened to me once or twice before, i walked in the other room and did the upgrade from the laptop without issue. then sync'd the phone back up with my desktop as was good to go.
On a side note, you don't need activesync installed to upgrade the phone. if you keep running into issues try from a different computer. thats what has worked for me.
flakrat said:
One other tip, from what I've read, it is recommended to make sure your Wizard is connected to one of the MAIN USB ports on your computer, for desktops, these will be on the back of the computer (the ones soldered directly to the motherboard). The ones on the front are usually essentially connected to a USB hub, and not directly to the controller.
On a laptop, all of the ports should be good.
Click to expand...
Click to collapse
Seconded. Use the USB ports on the back of the machine that are directly connected to the motherboard. Sometimes the ones on the front are connected to the motherboard via a cheap connection.
A number of manufacturers assume users will insert and remove devices which scrapes off the oxidation, and use cheaper metal because of this. A connection that stays in for a long time eventually builds a large enough oxide "crust" it causes problems with the electricial connection, and becomes flaky. This is possibly why a number of front-port USB plugs become intermittant after a while.
I've noticed newer PCs are using gold-plated contacts which tend to make this problem go away, but both mating contacts must be gold, else you get bi-metallic chemical reactions between them, and have the same problem as tin or copper-based contacts.
Sometimes there are so many things hanging off a computer's USB bus that you might just buy a PCI card with USB 2.0 plugs on it and use that.

USB device not recognized:Cant connect to laptop..??

laptop no longer recognizes tilt or tytn; changed usb cables; rebooted both devices and laptop; no go..
mssg I get is "one of the usb devices attached to this computer has malfunctioned. and windows does not recognize it"; any suggestions; cannot sunc nor tether via ISharing.
tia
a in yul said:
laptop no longer recognizes tilt or tytn; changed usb cables; rebooted both devices and laptop; no go..
mssg I get is "one of the usb devices attached to this computer has malfunctioned. and windows does not recognize it"; any suggestions; cannot sunc nor tether via ISharing.
tia
Click to expand...
Click to collapse
Hi
First of all try to reinstall Microsoft ActiveSync, than in the ActiveSync options, in your device, be sure that in "Connections..." setting "Synchronize all PC by this connection" is checked and below "USB" showed!
Otherwise, if your device, when connected to the PC, also doesn't charge (if you have this option enebled on your PDA!) there is some problem on your PC settings concerning the USB! Try to connect to someother PC to test it!
Ciao
thx...
@[email protected] said:
Hi
First of all try to reinstall Microsoft ActiveSync, than in the ActiveSync options, in your device, be sure that in "Connections..." setting "Synchronize all PC by this connection" is checked and below "USB" showed!
Otherwise, if your device, when connected to the PC, also doesn't charge (if you have this option enebled on your PDA!) there is some problem on your PC settings concerning the USB! Try to connect to someother PC to test it!
Ciao
Click to expand...
Click to collapse
hello there, first n foremost thanks for your input!
Before trying out your possible solution i tried to connect and for some reason i was able to connect via the device today...??!!
i really dont know why, but will try your soln if this situation reocurrs.
NB: this happenned to me twice in the last 3-4 months, n i never figured out the cause ??
any other advice or ideas gratefully accepted.;
its probably the same as me and loads of other people - the pins have bent on your usb connector - probably caused by using non standard chargers and usb leads. Its been widely reported. The non-standard leads have too much space around them when plugged in and wiggle causing the connector on the tytn II to bend. Try using the lead which came in the box and see if it helps. and try using the charger that came with it too.
Can bent pins be fixed?
Hello -- I'm one of those people with a non-recognition problem. Is it possible to fix the bent pins? My problem seems to have begun around the time I lost my original USB cable. Now, all the cables I have -- ones that have been specifically sold to work with my HTC Tilt -- have the symmetrical, sort-of-trapezoidal mini-usb connection, rather than the rectangle-with-one-corner-cut-off shape of the original cable. I should say these cables do charge my device, but none of my computers recognizes it as a USB device.
Help?
Thank you,
J. Georgia
bent pins continued
I should add that the charging cable that originally came with my phone has the same connector shape, so I'm not sure what's going on.
USB Device not recognised
This is known to happen at times win Windows, and not just for the TYTN2 but a myriad of devices.
The fastest fix for this:
Reboot ur PC/ Laptop.
If this Doesn't help - Then add in a reboot for the TYTN 2 also.
The problem will go away for some time.
I know its annoying, but this is way faster than troubleshooting for contacting MicroShaft Support.
axeman said:
This is known to happen at times win Windows, and not just for the TYTN2 but a myriad of devices.
The fastest fix for this:
Reboot ur PC/ Laptop.
If this Doesn't help - Then add in a reboot for the TYTN 2 also.
The problem will go away for some time.
I know its annoying, but this is way faster than troubleshooting for contacting MicroShaft Support.
Click to expand...
Click to collapse
Unfortunately this is no soution for me. I seem to have this problem as well, since about two weeks.
I use two notebooks (Dell & Acer) and both do not show any activity when connecting my Kaiser to the original USB cable. The device is not even switched on when I connect it, nor does this happen when I connect it to the (original) cable in my car, which did work before.
Charging works fine, both in the car and when connected to both notebooks, but no Sync at all.
I have tried another USB-cable with the same result, so I suspect some hardware-problem causing me to be unable to copy files between my notebook and my phone and worse, rendering me unable to flash a new ROM onto it.
Who knows what to do next?
I am mystified, too. USB Charging and audio connections work. I have rebooted my computer and done a soft reset on my phone several times, to no effect. I uninstalled and reinstalled Windows Mobile Device Center. Still nothing at all via USB. Once, yesterday, I somehow got a Bluetooth connection long enough to sync, but haven't been able to since then. Even then, Windows Media and AudibleManager couldn't see the phone. The really weird thing is, I can see the phone connection in my Bluetooth manager, but even with all the proper boxes checked, I can't sync. When I try from my device, I get an empty progress box which disappears after a fraction of a second. When I try from my computer, it says the device is not connected, but doesn't give me any option to connect.
Would a hard reset help?
If so, would returning an unlocked AT&T Tilt to factory defaults lock it back up? And what do I do if it does?
Please help!
J. Georgia
I have had similar problems with my touch pro in the past, even bluetooth internet sharing eventually gave up the ghost.
I tried a myriad of leads and then eventually reinstalled active sync- which did the trick.
USB sync not working
[email protected] said:
I am mystified, too. USB Charging and audio connections work. I have rebooted my computer and done a soft reset on my phone several times, to no effect. I uninstalled and reinstalled Windows Mobile Device Center. Still nothing at all via USB. Once, yesterday, I somehow got a Bluetooth connection long enough to sync, but haven't been able to since then. Even then, Windows Media and AudibleManager couldn't see the phone. The really weird thing is, I can see the phone connection in my Bluetooth manager, but even with all the proper boxes checked, I can't sync. When I try from my device, I get an empty progress box which disappears after a fraction of a second. When I try from my computer, it says the device is not connected, but doesn't give me any option to connect.
Would a hard reset help?
If so, would returning an unlocked AT&T Tilt to factory defaults lock it back up? And what do I do if it does?
Please help!
J. Georgia
Click to expand...
Click to collapse
I've had the same problem with my first Tilt. There's multiple threads that detail this known problem. Some seem to be due to bent pins, some are general hardware failures (possibly the USB controller). There are some HardSPL images out there that have a "force usb" option enabled. This never worked for me, but it might be worth a shot for you.
...a word of warning....
If you end up reflashing your phone (via MicroSD) and the flash goes bad, you may be stuck, as many of the solutions for repairing a bad flash require you to USB sync. My first Tilt was a victim of this after a bad stock ROM flash that left my device without audio, and unable to flash via MicroSD.
replace usb board
you need to replace your usb board. It will run you less than $10 if you do it yourself. you can get the board on ebay
really? 4 years later?

usb not working (only charging and headphones)

After the positive things after getting my kaiser back from repair I also noticed a huge problem....
I can't connect via USB to my laptop. If I plug in my device it starts charging and thats all, headphones works fine also... anyone a idea, below things i've done already..
-soft reset
-turn on/off advanced network functions
-tried different cables
-reinstall usb drivers on Laptop (vista)
-tried another computer (XP 2x)
-hard resetted the device
-do all the steps over again
I'm not planning to send it in for repair again... since I live in norway at the moment (normally in NL) I already lost it for 2 months...
Anyone a good idea?
cheers
Well you said it isn't working on vista, so I am willing to bet this may not work for XP. Check to make sure that you have the USB option in Active Sync checked. Other than that, I dunno. My USB port on the phone has been destroyed, I can barely connect to Active sync, but I am still able to charge. Stinking cheap plastic connector came out, tried to superglue it back, continue to come out, now the two pins on the right are busted.

HTC Diamond USB error

Hello everyone,
I'm having a problem with my Diamond. When I attach it to a USB port nothing happens. No 'hardware found sound' or what so ever.
I tried several other pc's with no result. It does charge when it is connected and the phone asks whether it needs to be in USB mass storage mode or in Active sync mode. I havent found anyone with the same problem so I'm afraid it is a hardware failure?
I tried:
-Soft/Hard reset
-Several computers/usb ports
-Disable Advanced Network capabilities
Does anyone have some tips that I haven't tried already that could help me out?
Thanks for your time!!
Disable Advanced Network capabilities under USB->PC in your Settings, that should do it.
I tried that also. With no result yet. Any other tips maybe?
First, check your cable for any marks that resemble rabbit bite marks or alligator bite marks.
No, seriously, check the points where the cable goes into the plugs for any obvious signs of damage, then check the cable itself.
Maybe, try using a different cable, if that doesn't work your Diamond most likely has a problem. If the different cable works, your cable is a goner.
Although I think there's quite a small chance that that's it, it's worth trying, right?
Use the 6.1 version of the Windows Mobile Device Center under Vista
Thx for all the tips. I didn't manage to get it working though
When the phone is connected to the charger it asks if I want to use activesync or usb mass storage. A friend of mine has also a diamond and his doesn't ask this. My conclusion is that it is broken
Damn I got this phone as a replacement for my broken K850i from my provider...They will go crazy when they see me again
Hi,
I have the same problem.
My guess is that it all started with a non compatible charger.
When charging it asked for active sync or disk.
After that the problems started, active sync doesn't work anymore.
Sometimes it workes when advanved networking is off.
Tested on different pc's, freshly installed.
Complete factory settings, notting works.
If synchronised by bluetooth it works.
I'm affraid i have to send the phone back for repairs and trow away the bad charger.
I never used a 3rd party charger.
Is there a way to update the firmware via bluetooth?? Because i'm still using the old slow version...
Same problem here. I've used my tomtom USB car charger. Is this a guarante matter, or do i have to pay for the repair?
You may have set the default connection to other than ActiveSync when first seeing the pop-up.
Go to 'Settings' 'Connections' and select 'USB to PC'.
Ensure ActiveSync is selected.
If you want the pop-up to display when the USB is connected (its good when you want to use your internal micro-SD as a memory stick), check the box at the bottom. You can select ActiveSync, Memory or PC Modem from when it appears on connection but when you just ignore it, it will perform whatever default selection you wanted last and then dissappear.
If all else fails perform a hard reset!
I've tried /soft/hard reset. No luck..
Can this be a hardware related fault, or could a ROM flash resolve the problem?
Transfering video files via BT is a pain in the a*s...
i would try a flash before returning it. You can probably dl an official 1.93.xxx.xx from htc and try that. You don't need hard spl and all that for those ROMs.
I have the same problem:
no connection at all from the PC-side. The Diamond comes up with the ActiveSync/Discdrive question and starts charging, but nothing else.
I did use external chargers that also trigger the ActiveSync/Discdrive question.
Update:
Oops, it seems fixed after a soft reset.
Same problem, diamond would not connect to PC.
Solution: Warranty repair---> they changed the motherboard, and everythings is good. Everything was free.
Edit: But now I have a different problem. I connect diamond in to PC, everything is good, but about 30 seconds after, mobile center looses the diamond, and sync won't work. Any solutions?
I have the same problem before. My Diamond USB cannot be recognised by the PC. Took back to repair and now working. But one PC still cannot recognize the diamond. The service centre told me they have reset my unit and when came back, everything has been cleared. I suspected a full reprogram of the ROM.
I have the same problem
I cant have any connection to the PC
so, no solution but the service people
USB Connection ERROR
I have the same problem. No computer seems to be able to connect to my P3700. I tried DL new ROM but I don`t know where my device came from. On HTC site from HK, which is the only one where I found a neutral Diamond with no carrier associated like, Sprint , Telus, or the like, its says The ROM Code can only be updated on HTC Touch Diamond Hong Kong English Version Device
Does anybody have a clue how to find out where my device was originally intended to be marketed? My ROM is 1.93.456.2 WWE dated July-10-2008? Do the the numbers 456.2 mean anything?
Help is highly appreciated!!
change your usb wire..
Epioneer said:
I have the same problem before. My Diamond USB cannot be recognised by the PC. Took back to repair and now working. But one PC still cannot recognize the diamond. The service centre told me they have reset my unit and when came back, everything has been cleared. I suspected a full reprogram of the ROM.
Click to expand...
Click to collapse
I already did. The first few times the problem occured it worked. I have 6 different USB wires and they all cause the problem. When I hook up my HTC Touch, they all work well!?
Won't sync with PC
Hi,
I have the same thing where it won't sync with any PC and i've tried all the "other" fixes and I've sent it to the service people to have a look.
Thing is, because I thought it was an issue with the usb connector I thought I would have a poke around with it myself and i could see one of the prongs looked like it wasn't making contact. To cut a long story short whilst i was trying to fix it the plastic tab in the mini usb connector came out completely
Service people are now saying that I've abused the handset and want to charge me £70 to fix it. Now to be fair, I have made it worse, but in my defense it was only because a fault had occurred that I started to dabble.
I also reported to the service people that the led light under the "end call" button had stopped working completely. This was definiatley not due to miss use.
I'm wondering if this led is on the motherboard like the usb connector is. If so, can i be cheeky and just ask them to fix the led and not the usb? but by default because the m/b would be swapped out then the usb would be fixed anyway?
If you looked at my phone it looks well cared for (which it was!!!) and its not like I've hammered it in anyway.
Anyone have an opinion or know if the led for end call and the usb port are both on the motherboard?
Thanks

Tytn II charging and usb problem?

Hi guys,
i have one very strange problem regarding TYTN II. It is almost new device, barely used but following things are happening:
1. Can not be charged while it is switched ON. In order to charge the battery i have to turn device OFF and than to connect it to the charger. Red light is instantly on and charging.
2. While it is ON and i connect it to the PC using USB cable, it is not recognized from operating system (it is not charging as well, it will charge though if i switch it OFF, same as with charger)
I can connect to my Tytn II using bluetooth and i have some questions.
Can i do HARDSPL 7 while conected to Tytn II via Bluetooth?
I want to upgrade my ROM using upgrade from SD card because obviously upgrade can not be performed using USB cable.
I did hard reset before i put this issue on the forum, can this be caused by the software or only hardware?
Thanks for input.
Jeremija
Check the settings->System->power. check whether the option "When device is turned on,do not charge the battery when connected to the pc" is selected. if so unselect it.
Already did that before first post, that option is not selected.
It is not only charging but TYTN II is not recognized while connected to the computer via usb cable.
this tytn ii is getting charged only and only if it is switched OFF, source can be computer or original charger.
I can get connected via bluetooth for data and my other question is if i can do HARDSPL 7 through bluetooth conection?
thanks.
jeremija_de_niro said:
Already did that before first post, that option is not selected.
It is not only charging but TYTN II is not recognized while connected to the computer via usb cable.
this tytn ii is getting charged only and only if it is switched OFF, source can be computer or original charger.
I can get connected via bluetooth for data and my other question is if i can do HARDSPL 7 through bluetooth conection?
thanks.
Click to expand...
Click to collapse
If its vista system then you probably need to disable the advanced USb functionality and try again.
To your next question, i havent seen anything till now that talks about flashing through bluetooth.
it is happening on both, vista and xp.
that is interesting question actually. Did anyone tried to flash over bluetooth connection, without using cable?
I would certainly prefer to use cable but my tytn ii does not get recognized when connected with the cable.
thanks
What have you done on the PCs to prepare them first?
Have you installed the software in the box on your PC before connecting the USB cable (Activesync 4.5) for Win XP desktops or the latest Windows Mobile Device Centre for Windows Vista? You need these before it'll connect/sync even though it's possible to use bluetooth without it.
Yes, on XP is installed Active Sync 4.5 and on vista i am using is latest Windows mobile device center.
Did you try disabling Advanced Network Functionality on the phone?
So other than trying what was already suggested and disabling Advanced Network functionality on the phone, I think it's time to call your countries HTC Support people.
FWIW whether or not you can use Advanced Networking Functionality is determined by the capability of the USB ports on your desktop PC. When I first got my TyTN II I couldn't get it to connect/sync at all and through trial and experimentation I came across the disable advanced networking workaround. Even with it disabled though I still found my Activesync connections to be unreliable and subject to frequent disconnections. I was using the native (and old as the hills) Via Appolo Pro USB 1.1 ports on my motherboard. I decided to upgrade to USB 2.0 so installed a quality NEC chipped PCI USB 2.0 adapter card. That means I now can use Enhanced Networking Functionality and I have not had an Activesync connection fail since. It was well woth the £9 it cost me for the card.
Everything is clear, thank you very much for your replies and advices. I`ll try to find HTC authorized service and let them judge
Thanks once again.
Jeremija
Is WiFi on?
My Vodafone v1615 (Kaiser) will not connect over USB if WiFi is enabled. No connection problem when WiFi is disabled via Comm Manager. Suggest you try this.
I tried everything i could think of, with or without sim card, with flight mode on, with GSM on but wireless off, name combination i tried it. Gave the phone to the friend who has exactly same model to try with his battery and if that does not work than i`m out of ideas except to send it for service.
I also noticed that if i leave phone on charger and OFF, red light lit for charging.
It can sit on charger for 24 hours but light does not change color to green (Full battery) but remains red.
I believe there is a problem either with battery or some component which is tightly connected to the usb socket/battery.
Will post results on monday/tuesday when i get my phone back.
Thanks everyone for input.
Jeremija
Same Problem
Just so you know i have EXACTLEY the same problem as you Jeremija... i have NO idea what is Causing it have you had any glory yet??
Kindest
Ben
Same problem as well
I just got my phone yesterday, and it had the same problem out of the box
it will not charge unless it's completely off, and it will not sync through a usb cable, when i connect it through USB it just keeps restarting, If anyone can come up with a solution short of returning my brand new phone back to the factory I would greatly appreciate it
USB charge & sync problem
What you have with your phones must be a hardware defect. I have the exact same problem with my Tytn II, but I know how it happened -- out of full stupidity. While at work, I connected it to a mini USB plug to charge, however to my surprise I found out that it was not 5v but 12v. I bought two external chargers and two extra batteries and I've been carrying around a pair of charged batteries since then. To be honest, because the phone notoriously drains the batteries very quickly having spare batteries is more practical than pluging it in and waiting for it to charge.

Categories

Resources