Database Develop

Hard Reset Kaiser/AT&T Tile?

I did the search, but not finding anything...Thanks for the help

Not sure what you want... but you can go to Start...Setings....System and choose CLEAR STORAGE and that will give you a hard reset as far as whiping data.

austinsnyc said:
-Enter Bootloader mode: Hold Camera + Power buttons together and reset with stylus(thanks pof)
-HardReset: Hold Both soft keys in while pushing in Reset button :When prompted push Green Talk Button to clear data.
Click to expand...
Click to collapse
This is the information I found... bu t I HAVE NOT been able to get my Tilt to Hard Reset from pushing any combination of buttons...
But this does work...
grizzley said:
you can go to Start...Setings....System and choose CLEAR STORAGE and that will give you a hard reset as far as whiping data.
Click to expand...
Click to collapse
Ron

I know this already. I am looking for combination of bottons + reset. As press softkeys + reset for 8525...etc
grizzley said:
Not sure what you want... but you can go to Start...Setings....System and choose CLEAR STORAGE and that will give you a hard reset as far as whiping data.
Click to expand...
Click to collapse

Don't forget about your good friend, WIKI.

I hard reset a TILT that was locked up after installing Blackberry connect to SD card (known issue). Hold down the two soft keys, then use the stylus to press the reset button for a few seconds, then release while still holding in the soft reset buttons. The warning message comes on, and as said earlier, use the green send key to initiate the data wipe.

Jim_R said:
I hard reset a TILT that was locked up after installing Blackberry connect to SD card (known issue). Hold down the two soft keys, then use the stylus to press the reset button for a few seconds, then release while still holding in the soft reset buttons. The warning message comes on, and as said earlier, use the green send key to initiate the data wipe.
Click to expand...
Click to collapse
interestingly, it does not work on my TyTN II.
However, its working on the Trinity.

It worked on my Kaiser/Tytn ll. Thanks!!!

not for me :-(
Hi,
maybe me being stupid, but this procedure does not work for me. Problem is that I installed software for the iGo bluetooth keyboard (I know ...) and ever since the Kaiser is resetting itself every 30 seconds. So what I get is only the smart mobility message, a short vibrate and then back to start. Anyone any idea how to get out of that? May I just press the wrong softkeys?
many thanks in advance
eRay42
new situation: the keys I press are definitely the right ones, I can also get into bootloader mode. I flashed the original rom (RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship) back which finished successful but the situation is the same. When I hard reset I am told it has been done, being asked to press the green button and it reverts to the old problem immediately. I should say that I have not modded my device so far, it was in original state before I installed the above mentioned software. Could it be a coincidence and it is a hardware problem?
HELP!!!

I found hard-resetting my HTC TyTN "GB" somewhat unpredictable. Holding down both soft keys while depressing the reset buttone is the correct procedure. It's either related to the HTC_END.cab. Do you have this installed?
Cheers

Strange, can't perform a hard reset either, using the softkeys of my TyTn II. No matter how long I press and hold them, no message screen, no option to hard reset.
The only way is to use Clear Storage.

pietrucci said:
Strange, can't perform a hard reset either, using the softkeys of my TyTn II. No matter how long I press and hold them, no message screen, no option to hard reset.
The only way is to use Clear Storage.
Click to expand...
Click to collapse
haha, my two fat fingers...
I finally managed to hardreset, using two pencils to push (only!) the softkeys.

pietrucci said:
haha, my two fat fingers...
I finally managed to hardreset, using two pencils to push (only!) the softkeys.
Click to expand...
Click to collapse
Pencil trick worked for me tooooo

reset
thank you..my tilt went crazy and won't bot...just keep restarting and turning off.
I had to use the pen and hold down
damn it now i have to restore everything

No still not working. These button things doesnt work. BTW does using Clear Storage give same effect, anyone?

I also haven't been able to perform hard reset on my TyTN II with the Soft Keys.. it just keeps rebooting! Can anyone help me?
Cumpz

LoL.. nothing like keep trying..
Already got it..

i read on another forum that i need to press the camera button and the power button, they are both located on the same side and press the reset button..
i done that but keep getting a red green blue and white bars, the text say sspl-1.0.0lipof and at the bottom serial..
its the same as the first thing i had to do to load wm6.1..????
thanks

icum said:
i read on another forum that i need to press the camera button and the power button, they are both located on the same side and press the reset button..
i done that but keep getting a red green blue and white bars, the text say sspl-1.0.0lipof and at the bottom serial..
its the same as the first thing i had to do to load wm6.1..????
thanks
Click to expand...
Click to collapse
It's in the Kaiser Wiki, under 'Kaiser resets'.

this is what is says...
Hard Reset **NB** This cannot be performed while the device is connected/charging!**
* Press and hold both soft keys
* Using a stylus, press and hold the soft reset button at the bottom of the phone
* Keep all three buttons pressed until the keypad lights turn off and then flash
* Release the soft reset button while still pressing the soft keys
* Let go of the two soft keys once the message "This operation will delete all your personal data, to manufacturer default" appears on screen
* Finally, press the green call button to perform the hard reset, or press other key to cancel
1. what buttons are the soft keys..
2. i pressed the power and the camera buttons then the reset set pinhole button.. release the reset pinhole button after the keypads lights go off still nothing..

Need serious help

Hi guys,
Great forum, unfortunately i can't find a solution for my problem. Here is my problem: I installed Diamond TF3D Config on my phone and i tweaked a couple of things, everything went well untill i changed the TouchFlow menus.
It automatically restarts, but the loading process can't pass the HTC logo screen and now it says:
" The Device is unable to boot because either you turned of the device incorrectly...----- Press SEND to reset your device..."
Well, ofcourse I followed the instructions and pressed SEND, but it looks like it doesn't do anything at all. The error screen above keeps displaying, without anything telling me that something is being done about the problem. Is it doing something or is it just stuck? (The light is continously on).
Can you guys help me? By the way I tried the manual hard reset, but that didn't help.

did you hard or just soft reset?

well i did a soft reset, that didn't work out keep getting that screen.
and I tried a hard reset but that wasn't possible, because i couldn't get in the device, so it pretended it was a soft reset..
but do you know if it is doing something or not , cause i get the screen continously with the lights on

PM the developer... sushilange... and then post the solution here for us all to take benefit of.

Not sure of your full situation, but two options that may help; hard reset, or connecting phone to pc and try running an RUU install; of course all data will be lost, device could be as well.
---- Hard Reset Option ----
To perform a hard reset:
1. Press and hold both softkeys on the device (the little dots above ok, and windows key). Keep these keys pressed, and at the same time, use the stylus to lightly press and hold the RESET button on the bottom of your device.
NOTE: I had no idea which of the many keys were considered the soft keys. They are the two buttons above the phone control buttons.
2. Release the stylus but keep the softkeys pressed when you see the following message on your device screen:
“Do you want to erase all user data and restore to manufacture default?”
3. Slide open the hardware keyboard, and press R to restore to factory default or press X to exit the hard reset process.
Note:
Your device will be set back to factory default settings. Please ensure any additional installed programs and user data have been backed up before a hard reset is performed
--- RUU install ROM --- (this is for the mogul, you'll have to find your own, just reading material)
http://www.htcamerica.net/support/mogul/software-downloads.html

k I will. And this guy has the necessary knowledge?

bjason6 , thanx for your help
but I don;t understand.
hardware keyboard, a diamond doesnt have a keyboard or do you mean something else and where are the two soft buttons i cant seem to find them

This is the proper way to hard reset the Diamond (taken from the wiki):
Switch the device off. Press and hold the "Volume Down Key" and "Action Button" (round button), at the same time, use the stylus to press the red RESET button in the stylus silo. You will be presented with a menu saying 'press R to reset, X to exit'. If you press R, your device will be set back to factory default settings.
Hard Reset will delete all data you have put on the device: Programs, Settings, Mail, SMS, MMS, etc., so be careful and make a backup before doing this.
After a hard reset, you will have a complete clean new install of Windows Mobile on your device.

I thought the phone must be on for the hard reset to work, because I doesnt work on y phone

and oh, the SEND button is just the phone button right? the one beneath the House-button?

Yes, bottom left "phone" button is send

YiuW said:
and oh, the SEND button is just the phone button right? the one beneath the House-button?
Click to expand...
Click to collapse
Nice
Now your tekin the pee mate

YiuW said:
k I will. And this guy has the necessary knowledge?
Click to expand...
Click to collapse
Well he wrote the app, so I bloody hope so

damn what the hell is wrong with my phone man damn...

YiuW said:
damn what the hell is wrong with my phone man damn...
Click to expand...
Click to collapse
LMFAO..... RTFM.... dunno

Anyone suggestions to solve this problem??
It doesn't seem that I can acces my phone via usb

Can you enter bootloader? WIKI

yeah i can

What can i do with the boat loader then?

YiuW said:
What can i do with the boat loader then?
Click to expand...
Click to collapse
Sail away ?

diamond doesn't hard reset, please help

hi all, my first ever post in this forum. first of all many thanks for being here.
I was reading too many threads about the diamond. mainly about hard reset problems and new roms. my problem is that I couldn't perform hard reset. searched over the forum, tried what others did, just no result, what I am getting is only soft reset.
the method is:
use reset button while holding volume down & enter buttons , release the reset and keep holding others until the information window appears on the screen... somebody says power button also needed to be hold. somebody suggest holding the enter button very carrefully as it is very easy to activate direction buttons. somebody says rom is need to be updated as existing rom can be corrupted.
I tried all of above, I did update the rom several times and checked if hard reset is working, no result.
my tricolor screen says :
DIAM100 MGF 64M
SPL-1.24.Hard
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
I've 1.37.405.1 and radio rom 1.00.25.03 now, I know they are older versions but I tried 1.96. series too but did not throw in another hspl.
is it worth to try flashing with newer hard-spl such as 1.93 and compatible roms. any suggestion is very appreciated. I just wory about it coz read in many threads it is good to perform a hard reset after a new rom.
ps:assuming if it is cannot be changed, any software to perform hard reset? sow somewhere video of it, any help?
thanks for reading

Read this.
http://www.hardreset.eu/htc_touch_diamond_hard_reset_soft_reset_en.html

thanks for post but link doesn't work. I assume there is just explaination of normal hard reset method which I tried several times already.

Hi
cant open the above link to confirm if the same as what method i use, press and hold volume down and enter and the reset and release all upon tri colour

i must remove the SIM to get a hardreset.
with inseted SIM the procedure not works on my device (why ever? no idea!)

Just to further clarify:
If you have the CDMA version (like I), you must hold down power button + volume down + enter button at same time. Press the reset button with your third hand and continue holding the buttons until a screen prompts you for a reset. Volume up button will confirm the hard reset.
That's what I had to do and I would love to meet the engineer behind that crazy combination... I had to prop the stylus in a 3 ring binder while holding the three buttons so i could jab the back of the phone into the stylus while my other two hands were preoccupied with this stupid combo.
Arg. Hope this helps
/rant

ekksman said:
Hi
cant open the above link to confirm if the same as what method i use, press and hold volume down and enter and the reset and release all upon tri colour
Click to expand...
Click to collapse
this is not the hard reset. I got the tricolor screen by holding volume down + reset button. for hard reset there must be a window asking your approval if you are confirming hard reset, than pressing volume up is performing it.
while holding volume down + enter and resetting is resulting soft reset only. I tried many times as if I am mistakenly pressing other buttons but not... any help?
edit:with sim or without it didn't make any difference. however, I tried the last method whitesoxxx suggest but didn't hold the reset as I hold the others, will give result in a minute. by the way my device is from orange, is it CDMA (sorry if it sound soo stupid
result:nope, didn't make many difference, still soft reset. one more question: this reset confirmation window, how many second later it suppose to appear?
thanks

my last post might point you in right direction...

WhiteSoxxx said:
Just to further clarify:
If you have the CDMA version (like I), you must hold down power button + volume down + enter button at same time. Press the reset button with your third hand and continue holding the buttons until a screen prompts you for a reset. Volume up button will confirm the hard reset.
That's what I had to do and I would love to meet the engineer behind that crazy combination... I had to prop the stylus in a 3 ring binder while holding the three buttons so i could jab the back of the phone into the stylus while my other two hands were preoccupied with this stupid combo.
Arg. Hope this helps
/rant
Click to expand...
Click to collapse
It is an incredibly stupid combo! I had to search xda-developers to figure it out the first time because i just didn't believe the user manual!
For me, it works easiest with the diamond face down on the edge of a desk and supported against a heavy object (shelving unit) so that the Vol Down & Enter combo can be done one handed. I then have a hand free to press reset, which is easy with the back cover off!

beleive me i have no any complain about how difficult to reach ald hold all those buttons at same time, I am quite use to it
I sent back the diamond today as hard reset problem was really annoying. I tought mine was defected somehow. will buy another, if next one does the same should I send it back again? is it really necessary to do hard reset after updating rom?
thanks

To perform a hard reset
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and
ENTER button, then press the RESET button with the stylus tip.
3. Release the RESET button, but continue pressing the VOLUME DOWN and ENTER buttons until you see a message on the screen.4. Release the VOLUME DOWN and ENTER buttons, then press the
VOLUME UP button to perform the hard reset, or press any other
button to cancel the reset.
4. Release the VOLUME DOWN and ENTER buttons, then press the
VOLUME UP button to perform the hard reset, or press any other
button to cancel the reset.
***Check this out! http://www.hardreset.eu/htc_touch_diamond_hard_reset_soft_reset_en.html
***I tried it,but the problem with YouTube didn't stop.

Very easy way to Hard reset the phone is by going to phone settings and select "Clear Storage" and enter 1234 click ok. (This is erase all the data and installed programs and will get the factory settings)

Howto hard reset / Soft reset?

Howto hard reset / Soft reset?

Soft reset:
Poke your stylus at the reset button.
Hard reset:
1. turn off the phone
2. Hold both right and left buttons (the ones right under the screen, dont know the name)
3. press power button, while still holding the others
Another way of doing it is hold the two buttons and poke your stylus at the reset button, then on your keyborad press r

Dont have the reset button using the ROM from XDA
(Nov 21) Touch-IT X1 M-HD 1.1 <<<UP NOW>>>

The reset button isnt a software feature, its a physical button, located under the battery cover in the middle of the stylus silo.
Check your X1 manual, its all described in there.

Bit of a silly question here but im fairly new to WM, after owning my X1 since for a while now, i've installed all manor of rubbish on it testing bits and bobs out.
Just wanting to know a few things about the reset if anyone could confirm them:
Soft reset:
Just resets the device and boots back up as normal without removing anything?
Hard reset:
Removes everything back to factory default. Though I have heard people not being able to use GPS and messaging/internet. Mine was not a branded device so I imagine it should be fine.

That's about right.

hello
can i just clarify here then - if u soft reset, then u will not lose any files/pictures/programs/softwares etc in ur phone?
cheers

fifa84 said:
hello
can i just clarify here then - if u soft reset, then u will not lose any files/pictures/programs/softwares etc in ur phone?
cheers
Click to expand...
Click to collapse
A soft reset is the same as turning the phone off, then back on.

Dare1 said:
Soft reset:
Poke your stylus at the reset button.
Hard reset:
1. turn off the phone
2. Hold both right and left buttons (the ones right under the screen, dont know the name)
3. press power button, while still holding the others
Another way of doing it is hold the two buttons and poke your stylus at the reset button, then on your keyborad press r
Click to expand...
Click to collapse
Your methods are lies. They don't work.

poetryrocksalot said:
Your methods are lies. They don't work.
Click to expand...
Click to collapse
It works ! I've done it a couple of times now.

williyung said:
It works ! I've done it a couple of times now.
Click to expand...
Click to collapse
What am I doing wrong? Why doesn't it work?

poetryrocksalot said:
What am I doing wrong? Why doesn't it work?
Click to expand...
Click to collapse
You have to hold the 2 keys mentioned and the power button "all at the same time" then release the power button first. after that press R on your keboard, that should do the trick. tried it and it works

Keep the soft keys HELD DOWN until the color screen shows up.

laurence0609 said:
You have to hold the 2 keys mentioned and the power button "all at the same time" then release the power button first. after that press R on your keboard, that should do the trick. tried it and it works
Click to expand...
Click to collapse
Thanks for this specific method.

How do you know if its worked, the phone turned on straight away when i held down the left and right button and power, should it do that?

why do people reset their phones daily or just alot? wat does it do for u?

Soft Rest, Hard reset .. 1 finger
In your dialer type *74*# and then dial.
It will ask you for soft reset, hard reset or Device info.
Eazy, convinient,...working in almost all ROMs (but I have had a ROM where it was not working)... Now I have EneryROM and it works!

marekriedl said:
In your dialer type *74*# and then dial.
It will ask you for soft reset, hard reset or Device info.
Eazy, convinient,...working in almost all ROMs (but I have had a ROM where it was not working)... Now I have EneryROM and it works!
Click to expand...
Click to collapse
Doesn't work for me (Smaberg's Touch X 10.1)

The key thing people are doing wrong is holding down the power button and the two soft keys when hard resetting. make sure you let go of the power button straight away! (continue to hold the soft keys!)

marekriedl said:
In your dialer type *74*# and then dial.
It will ask you for soft reset, hard reset or Device info.
Eazy, convinient,...working in almost all ROMs (but I have had a ROM where it was not working)... Now I have EneryROM and it works!
Click to expand...
Click to collapse
100% work for me
thanks for wonderfull sharing

Hard Reset Problem, really driving me crazy.

Hello everyone.
I am new to the whole custom rom and flashing thing, but after some reading and researching I decided to backup my stock rom and flash a custom one.
So I did successfully, to the point when the flash is done and I should do a so called Hard Reset. I've done the hard reset thing before and it worked, but now when I hold the both "silver" couloured buttons and the powerbutton at once the phone vibrates once and start booting.
I just don't know how to proceed with this since my X1 won't go in to Hard reset mode, I have no idea why or what I should do, so please, anyone just give me a hint and make my day.
Sorry if this is a totally useless thread for everyone else and it's just being annoying, but I really need some help here guys and girls.
Thanks in advance / Anton.

You probably just haven't gone through this procedure:
http://forum.xda-developers.com/showthread.php?t=431218
Hope that solves it
Good luck!

Actually I did, I followed BioVolt's videoguides on every step and when I checked afterwards on the tri color bootloader-screen it said: "KOVS110 SPL-0.72.01iNex" wich indicates that the Hard SPL procedure was successful.
Thanks for the hint tough, problem still not solved...

blondyz said:
Actually I did, I followed BioVolt's videoguides on every step and when I checked afterwards on the tri color bootloader-screen it said: "KOVS110 SPL-0.72.01iNex" wich indicates that the Hard SPL procedure was successful.
Thanks for the hint tough, problem still not solved...
Click to expand...
Click to collapse
I had the same problem - what you need to do is NOT hold the power button for long, just for like a second then it should work.

I too faced hardreset problem earlier, then later i found the following procedure holds corrects, atleast for my mobile. What i do is, press both silver buttons at a time and press power button only once and leave it(just press and leave only power button not the silver colored ones)..after few secs it will go to hard reset mode...

Try holding down the volume down button and the power button to go into the bootloader mode. From there, continue with your normal hard reset procedure which is holding down the 2 silver buttons and then press the reset button.

You only need to hold the two soft keys (silver buttons) to get into hard reset mode. if your phone is off, then you only need to tap the power button to turn on the phone, not hold it, but continue to hold the silver keys until you get the grey screen.
Hope that helps

blondyz said:
.....
So I did successfully, to the point when the flash is done and I should do a so called Hard Reset. I've done the hard reset thing before and it worked, but now when I hold the both "silver" couloured buttons and the powerbutton at once the phone vibrates once and start booting.
I just don't know how to proceed with this since my X1 won't go in to Hard reset mode, I have no idea why or what I should do, so please, anyone just give me a hint and make my day.
................
Click to expand...
Click to collapse
You need to completely shutdown your X1 first before hardreset. I mean COMPLETELY: remove your battery for at least 5s, then attach it and hard rest your device.

Thanks alot guys, actually the problem got solved by now, I treid a method I hadn't heard of before where you hold your two softkeys and under the battery cover give the "stylus hole" a push..
Worked just fine! Thanks alot to everyone bothering to help me, it's thanks to you guys I now have a working X1
Kinds regards / Anton.

the reason why its hard for people to hard reset from when its off is because they're holding the power button as well as the two silver keys!
you just hold the two silver keys and press the power key once, quickly.
keep holding the two silver keys until press R comes up!