Related
Okay, I'm stumped. I'm already getting a replacement device from HTC under warranty so my problem is solved, but like many of you, I HATE NOT HAVING AN EXPLANATION FOR THINGS!
I'm also wondering if anyone else has had this problem? About 10-Days ago my Kaiser (Tilt) stopped charging via the automotive charger. The A-C charger works fine, but the vehicle charger sent to me with my device from AT&T completely stopped charging my device. I went to the AT&T store & bought a new charger, It didn't work. I changed power points, & cigarette lighter in the vehicle &, it wouldn't work. I tried the charger in the vehicle of two different AT&T sales guys & also tried multiple chargers, & it wouldn't work. Is there any reason why the unit would lose it's ability to charge via a vehicle charger while still retaining it's ability to charge through USB to computer & through the A/C home charger? It seems to me that if the charge portion of the MB was fried, then all charging would be affected.
So how can my device charge fine through all means EXCEPT the vehicle charger?
Again, AT&T is sending me a new device, but I hate not having an explanation for the problem, drives me Nucking Futs!!!
Any ideas, anyone?
Thx!
I dont want to sound rude but have you checked your power settings?
Under the "Advanced" it has a option for "When device is turned on, do not charge the battery when connected to the PC."
If this is ticked it will not charge via the in car charger.
It's a known issue, not just with the Tilt
I had the same problem with my Axim X50 and X51v.
The original sync/charge cable wouldn't charge from the car's lighter, while non-branded cables did so without any problems at all.
This happened with other Axims as well, so I know that it wasn't a defective unit.
I then purchased an HP Ipaq HW6910, and encountered the same issue with my wife's Mazda 5 - the HW6910 woudn't charge if the cable was connected to the charger, when I started the car. It only worked if the adapter and cable were disconnected while staring the car. This did not happen with my Mazda 3 or my Mitsubishi.
And another thing I discovered, is that some cables are not designed for use with car chargers, but they work perfectly with AC chargers.
I bought a couple of retracting sync/charge cables for my HW6910, they worked only when connected to the mains. But regular cables worked perfectly with both power sources.
Jygar said:
I dont want to sound rude but have you checked your power settings?
Under the "Advanced" it has a option for "When device is turned on, do not charge the battery when connected to the PC."
If this is ticked it will not charge via the in car charger.
Click to expand...
Click to collapse
OF COURSE I DID.
Yeah, It charges fine from the PC, & from an A/C source. But the HTC TYTNII car charger that came with my device, as well as replacement car chargers don't work.
wisniak said:
I had the same problem with my Axim X50 and X51v.
The original sync/charge cable wouldn't charge from the car's lighter, while non-branded cables did so without any problems at all.
This happened with other Axims as well, so I know that it wasn't a defective unit.
I then purchased an HP Ipaq HW6910, and encountered the same issue with my wife's Mazda 5 - the HW6910 woudn't charge if the cable was connected to the charger, when I started the car. It only worked if the adapter and cable were disconnected while staring the car. This did not happen with my Mazda 3 or my Mitsubishi.
And another thing I discovered, is that some cables are not designed for use with car chargers, but they work perfectly with AC chargers.
I bought a couple of retracting sync/charge cables for my HW6910, they worked only when connected to the mains. But regular cables worked perfectly with both power sources.
Click to expand...
Click to collapse
Funny, I just ran out to the truck & grabbed one of the guys Blackberry chargers & it looked like it was working. But SK Tools reports an even bigger (negative) amp draw (like discharging twice the normal rate). So with the BB charger it dischages even faster. Maybe reversed polarity Guess I should've checked first. That's a moot point now though as I await my new unit. Weird though.
Well i was using a BB charger that worked fine up until this morning. i bought my phone when it first came out so it wasnt easy to find a charger made for it at the time. i never had a problem until today. i also noticed that the Usb terminal on my device was bent. i called htc but they charge way too much to fix it. i have no idea how or when the terminal broke but it does still charge when pluged into pc or into the wall. ill have to spend $80 to have ppctechs fix it.
wassup, i`m in SF Cali, I had a att 8525 that was doing the same thing. I assumed it was the phone when it 1st started happening. After a week or so it was bothering me so i started playing with it trying to figure out if it was a setting, bad flash, or hardware. I noticed that if the phone was off it wood charge but not if it was on. I started flashing my phone and testing (for trouble shooting purposes) and for the first 2 or 3 roms problem still existed, then one of the roms i flashed to would turn on the back light as if it was charging but no LED or charge, when this started happening I realized that if i turned my fone off it wood start charging and continue to charge when i booted the fone back up. So if when i got in the car i pluged in/ shutdown/ waited like 45 sec or 1 min. / then booted it would temp. fix the problem for as long as my fone was on the cable. At some point after that many weeks/roms later i noticed it was working correctly again, So I had decided it was a glitch in the rom, But i`m not a Dev. or fone guru so I really dont know what it was, but hope this helps someone.... PEACE!! ~bboyphrog1~beatz`n pieces krooh~
flexte said:
Well i was using a BB charger that worked fine up until this morning. i bought my phone when it first came out so it wasnt easy to find a charger made for it at the time. i never had a problem until today. i also noticed that the Usb terminal on my device was bent. i called htc but they charge way too much to fix it. i have no idea how or when the terminal broke but it does still charge when pluged into pc or into the wall. ill have to spend $80 to have ppctechs fix it.
Click to expand...
Click to collapse
The slight diagonal slant on the bottom right? It's supposed to be like that. All AT&T Tilts (and I'd assume TyTN II's, but I've never had one to compare) have a mini-usb port that looks that way.
i looked at a 8525 and the usb terminal was straight. i even took a pencil and straightened mine out. it should be bent. that wouldn't make sense because the charges slot is not bent. i think the problem is that one side of the terminal is not soldered to the board and can easily be broken. in another thread 3 people have the same issue. as far as the car charger goes ill do some testing but until today it was charging fine while the phone was on.
this issue is known ,it even happens with the htc tynt.... by simlpy rebooting while in the charger it starts working again ..at least with mine.
I've had the same problem. I went to the lcoal AT&T store and they said they never heard of it so I thought it was just me. It looks like many of you have the issue. I wish I knew what it was. It was really bad with my 8525,
i thought Faria developed a cab to fix this issue in the hermes forum? might be worth having a search for it and when i get home i will see if i have a copy on my pc.
any of you guys get anywhere with this? I have exactly the same problem. posted in a couple of other threads actually.
Not sure whether the usb port is damaged, but it's certainly is slightly "down" on the right hand side.
It charges perfectly on the mains and perfectly from usb, but not in the car.
I have used a normal car charger, spent £50 on a Carcomm powered mount and tried one of the separate chargers that you plug the standard mini usb cable into. Nothing works. This is driving me crazy (if you'll excuse the pun!) a the primary reason I bought the Kaiser, was for GPS.
Thanks
well i also just found out 2 of my minisync cables dont work anymore. 1 of them still charges the phone but neither of them sync the phone anymore. it still syncs fine through a normal usb cable.
I am using a moto Razr car charger and it works fine so far.
Okay, confirmed on my replacement Tilt: The USB port is arrow straight. Someone earlier mentioned it being lower on the right side & indeed my DEAD DEVICE was as such. Looks like a bad job of connecting the port to the device.
NOTE!!!!!!
It's a good idea to take a look at your charger before you plug it in to make sure the charger USB connector is not bent or mi-sshappened.
i have the same problem i went through 4 att car chargers adn 5 phones. They are crap. Its not the phone its the charger if you play with it you will see that it comes and goes. The end tip on the charger is bad doesnt make a good connection. i have yet to find a good car charger.
Mine stopped charging using the car charger supplied and a brodit. A friend's kaiser charges OK with the same chargers.
No-one has mentioned it in this thread, but my phone, shows "charging" in the battery control panel and the LED lights up to confirm this. The percentage charge value decreases as though it isn't being charged!
As others have done I noticed that the corner of the plastic centre of the connector nearest the reset hole was slightly bent and I assume (though can't remember doing so) that I missed the reset hole with the stylus tip and pushed it in. Menu driven resets for me from now on!
HTC Europe didn't know anything about this fault, so seem to be happy to repair / replace it under warranty. It's with them at the moment, so I'll have to wait and see.
RSVRover
faria said:
this issue is known ,it even happens with the htc tynt.... by simlpy rebooting while in the charger it starts working again ..at least with mine.
Click to expand...
Click to collapse
that didnt work for me. only one of my chargers work now.
RSVRover said:
Mine stopped charging using the car charger supplied and a brodit. A friend's kaiser charges OK with the same chargers.
No-one has mentioned it in this thread, but my phone, shows "charging" in the battery control panel and the LED lights up to confirm this. The percentage charge value decreases as though it isn't being charged!
As others have done I noticed that the corner of the plastic centre of the connector nearest the reset hole was slightly bent and I assume (though can't remember doing so) that I missed the reset hole with the stylus tip and pushed it in. Menu driven resets for me from now on!
HTC Europe didn't know anything about this fault, so seem to be happy to repair / replace it under warranty. It's with them at the moment, so I'll have to wait and see.
RSVRover
Click to expand...
Click to collapse
Please let me know the outcome. mine is getting worse by the day.
Now I'm confused.
Because the device charges over USB I just assumed it would draw <500mA (the max output of a USB port) but the specs say it draws up to one amp.
Having owned a high-drawing device before (Axim x50v) I know that trying to pull this out of a USB port can blow your motherboard. So are these safe to charge over USB??? How does the device know whether its being charged over USB or mains - are there different charging pins on the connector?
I'm creating a new thread because I think my charging issue is unique...
My Kaiser will show an orange light and indicate that it's charging when:
1. Powered On and plugged in to: USB, AC power Adapter, or Car charger
but it will not take a charge and the orange light goes out after about two minutes.
2. Powered Off and plugged into: USB, AS Power, or car charger
but the orange light remains on and it never charges (tried 5 hours)
The device also does not sync, I don't see anything physcially wrong with the USB port, but it was damaged by water several weeks ago, it hasn't worked properly since.
I've been getting by with an external battery charger that I purhcased from Ebay.
Does anyway have any ideas? I've reflashed the device since then as well and there is no change in how it reacts to charging..
Hi echofive
I have the same problem with my Kaiser but at least it charges with just one of my 5 AC power adapters. Not in my Car charger and not on a USB connection.
Maybe it has something to do with the small USB pins on the Kaiser which are not properly aligned. You can try to bend them.
Good luck.
Hello, I was having this same issue and (long story short) I believe that it is the small USB pins on the phone.
Here is what I found (sorry knda long post). I have two ATT TILT phones. My Original Tilt phone got soaked in water but I was able to almost salvage the phone by soaking it in Denatured alcohol and letting it dry. This 'wet' Tilt has all functions but cannot read sim cards. It does however charge perfectly.
The replacement Tilt I have works like a charm but refuses to charge. Regardless of USB charging, off the wall charger or car charger, the orange light comes on, says it is charging but in 2 minutes the light goes out. The phone is still listed as charging but I know it is not charging because the battery level continues to drain. The phone does sync to my PC and I am able to transfer files to/from my new TILT via a USB cable. Just cannot charge the device.
I have 3 batteries. 2 stock batteries and the large 3200mah battery. All three batteries will not charge on my new TILT. I tried charging it via USB connected to my Computer, Car cigarette lighter, Car inverter charger, official TILT charger from CINGULAR ATT. Completely unable to charge the device.
If I attempt to charge the batteries (all three of them) on my old 'wet' TILT the batteries charge regardless of what method I use. It will charge via USB connected to the PC, USB connected to wall charger, official ATT TILT charger, or car charger. No issues. So I know the chargers, cables and batteries do charge on a TILT. Both TILTs are official ATT TILT devices. Two of the batteries are stock and 1 of the batteries is a SEIDO 3200mah.
Sometimes I get lucky and the new TILT phone does charge. In these cases I charged the phone using the Wall charger and the battery was over 50% capacity.
Now I know the new Tilt USB port is working because it syncs to my PC just doesnt charge after 2 minutes (light goes out) and battery continues to drain (watched and tested this after 3 hours of observation). I ended up ordering one of those TILT USB connectors which have a 3.5mm headphone jack and USB port.
This device: http://www.amazon.com/i-Trek-Stereo...8&s=musical-instruments&qid=1230877732&sr=8-4
What is weird is that I can now charge my NEW TILT using the USB port on this connector with this connector attached to my new TILT. If I attempt to charge the TILT using the onboard USB port, it stops after 2 minutes and the light goes out.
Personally, i think it has something to do with the pins. Hope this helps someone.
Jinkage said:
Regardless of USB charging, off the wall charger or car charger, the orange light comes on, says it is charging but in 2 minutes the light goes out. The phone is still listed as charging but I know it is not charging because the battery level continues to drain.
Click to expand...
Click to collapse
Been there, had that problem and the solution was even simpler and didn't involve the charging/USB port at all. Get a cotton bud (US folks call them Q-Tips) and spray some contact cleaner on it (not anywhere near the phone) and use it to carefully clean both the gold strips/terminals on the batteries along with the gold spring terminals on the phone. Although they may look clean, invisible grime film can make the connection fail and cause this problem. This is also a good tip to follow with ordinary household battery rechargers and NiMH cells. I haven't had this problem since but still carry out a terminal clean every few months to be on the safe side.
My phone wouldn't charge anymore. Searching through threads I found a magnificent magnified picture of the mini-USB port and the way the right part of the port was bent down a little. It was exactly like that with my phone, I used the pointing stick to tilt it up a little (be careful it may break of the pins, and that would lead you far from home!), which fixed! Haven't had the issue since!
Regards,
Nika.
Hi.
Have you still the link with the picture . I have the same problem an i am afraid , that i can kill my Kaiser
Regards
Dariely
Nope, sorry...
I had a similar issue with my Kaiser. It would charge with a USB cable and an ac adapter but not in the car. It used to but stopped. I took a dental tool and lifted the two little legs inside on the bottom of the mini usb port so they would contact the charger again and all is well.
nikagl said:
My phone wouldn't charge anymore. Searching through threads I found a magnificent magnified picture of the mini-USB port and the way the right part of the port was bent down a little. It was exactly like that with my phone, I used the pointing stick to tilt it up a little (be careful it may break of the pins, and that would lead you far from home!), which fixed! Haven't had the issue since!
Regards,
Nika.
Click to expand...
Click to collapse
YEAH!
Great Tip!
had the same issue as you a long time!
tilt up the pins: no more problem!
THANKS A LOT !
I straightened up the last pin. I was beginning to think it was my AC Charger...I plugged it in my Ashtray charger and it charged without a problem. I will see if this takes a charge. I didnt use any denatured alcohol, I just took the compressed air canisters used for computers and cleared out the usb port....
we wait now
My 18 month old Tytn is not longer charger via the wall chager or car charge. But strangely it will charge is connected to the PC. I have tried a few different wall chargers including the original one and also test the wall charger on other charge by USB plug devices.
I have done a hard reset and also re-installed the stock rom.
Any other idea's ?
Same strange thing happens to me since 2 weeks.
No Charge with power adapter, tried different modells.
No Charge in car
But Charge via USB from PC . And Activesync works...
Any Idea would be very helpful.
tytn2user said:
My 18 month old Tytn is not longer charger via the wall chager or car charge. But strangely it will charge is connected to the PC. I have tried a few different wall chargers including the original one and also test the wall charger on other charge by USB plug devices.
I have done a hard reset and also re-installed the stock rom.
Any other idea's ?
Click to expand...
Click to collapse
Same here, no fix, just dealing with it, hoping the charge by usb doesn't crap out.
A few months ago I receive a wallcharger from a friend who had a HTC TOUCH, as I inspected the voltage on my original TYTN II charger and the touch charger I figured out the touch charger would do the job, so I plugged in and for a brief moment the amber light go on, but almost inmediately it went of, so I guess it would not work with my phone.
But I rechecked the voltage and got me thinking what could be wrong, and after messing around a little bit with the charger and the usb plug I found out that for some reason if I plug the usb jack all the way down it doesn't make contact with the phone usb, so I have to plug it half way to make it contact and charge the phone.
Maybe that would be your case.
Good Luck.
in my situation the yellow loading light of the TytnII is even switching on when I connect the power charger . But even after being yellow=loading for a full night .
No Change in battery status
Freecall
My Tilt had a loose Mini-USB connector thing.
:S
OK. After reading people having the same problem I decided to pull mine down and take a look. Expecting to find a blown SM fuse on the circuit board. To my surprise I did not find any SM fuses in that area of the USB plug. While I had it apart I noticed some damage to the USB socket, viewable from the outside without having to pull it apart . I re-assembled the unit and VERY VERY carefully tweaked the damaged pin (pin 1 in my case) with the tiniest sewing needle I could find in the sewing kit. I bent the gold color wire back into a position matching the other 4 and pulled it into a wall charger and it started charging. So the problem in my case was a damaged pin 1 in the USB plug visible from the outside.
Charging is done by the two outside pins.
For the pinouts check out http://pinouts.ru/Slots/USB_pinout.shtml Picture on the left hand side of the screen called MINI is the same as looking at the plug on the tytn from the outside.
While looking at the plug with a magnifier I could clearly see that pin 1 was collapsed into the plastic center part and would not be making contact with the USB charger when inserted.
I will need to take more care when inserting a USB plug from now on and reduce the amount of time I used the plug. I have been geocaching with my TytnII the last few weeks and it has resulted in a lot of plugging in each time when returning to the car. This practice will have to stop for me if I want to get more millage out of my tytnII.
My HD2 has just killed it's second car charger, grr! Has anyone else had this problem with generic micro USB chargers? Or genuine HTC ones?
The power light comes on in the charger but nothing happens on the phone. My car holder charger was in 2 sections, a mini USB cable to the cradle and then a converter to micro USB in the cradle. If you swap the mini USB cable the rest works, but with the broken cable, the cradle power indicator still lights up.
Thanks in advance if anyone's had the same problem or got some advice.
dizzi141 said:
My HD2 has just killed it's second car charger, grr! Has anyone else had this problem with generic micro USB chargers? Or genuine HTC ones?
The power light comes on in the charger but nothing happens on the phone. My car holder charger was in 2 sections, a mini USB cable to the cradle and then a converter to micro USB in the cradle. If you swap the mini USB cable the rest works, but with the broken cable, the cradle power indicator still lights up.
Thanks in advance if anyone's had the same problem or got some advice.
Click to expand...
Click to collapse
How hot is the phone?
If it is too hot (usually from a car charger in a hot environment), the Leo will not charge. The HD2 will blink green and orange.
Hello dizzi141,
Same problem here, already one car charger down. I have a red led burning on the car charger but nothing happens on the device ...
Grtz
My charger is working but charger is getting very hot and it charging the phone very slowly like 7-10 min one percent (%1) any way to fix this problem?
It's not a heat thing as far as I can tell, it works one minute and then next time it's dead. The phone doesn't recognise it's plugged into a charger even.
So the led is not blinking at all? (when plugged in to charger)
Shure that its your htc hd2 killing and not the car ? Cheapass chargers suks bigtime
Power consumption
Could it be that your generic charger is rated at 500mA and the HD2 can draw somewhere between 1500 and 2000mA ?
That might blow a fuse (or burn up the voltage regulator if unfused) in the "el-cheapo" car charger..
Personally, I'm using a 1000mA USB adapter from dealextreme.com
http://www.dealextreme.com/details.dx/sku.34040
and a standard USB cable.
Works perfectly for me.
(Sure, I might get the orange/green LED, but that's because of heat. I get that with original charger too, if it's too hot when I charge.)
Just my two cents...
I used to have a lower power generic car charger but it blew after a couple of months of occasional use.
For 'peace of mind' I brought the official HTC one as advised in the accessories section of their website, it's still working fine now after about 3 months of occasional use (just have to wiggle it around a bit to make a good connection in the socket sometimes).
I do have to align the screen mount to an aircon vent on the dash to keep it cool though, it overheats in no time - and that's just uk heat!
I haven't had any problems with heat or charging. I use this http://www.newegg.com/Product/Product.aspx?Item=N82E16882021129 , you can get them pretty cheap if you watch their email promos.
I'd agree with Bonzo.
I have tested few chargers (Samsung branded including ).
Everything what was not marked as 1A (1000mA) output was useless.
i use the origininale htc`s car chargers.
they work flawless.
CC-C200 for the hd2
i had a CC-C100 before.
Hello during vacation my phone fell into the sea. I did all I could, dry it and put it into the rise for 2 days. Everything works perfectly but charging. When phone is On it shows charging (no fast, just regular) but nothing happens. When phone is off it charges slowly but it charges.
What do you think if change of the connector plate will solve the problem?
Did you try other cable?
Yes, I have tried cable, quick charger, slow charger. There is no difference. I have ordered small plate with the charging connector to change and to see if it will resolve issue