Database Develop

Help: Htc Diamond Nand Bad block

Here is what I have.
Does anybody know how to fix that?
Thanks very much.
I am waiting online!!!
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 579 (0x243) is bad block
BLOCK 1212 (0x4BC) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x900
Partition[2], type=0x25, start=0xF40, total=0xB080
Partition[3], type=0x4, start=0xBFC0, total=0xF000
CE Total Length(with sector info) = 0x603FE00
CE CheckSum Length(without sector info) = 0x5FE0000
Here is the answer from our master Olipro!
ECC checking is fully integrated into the Diamond SPL, there is nothing you can (or need to) do.

Maybe THIS is useful for you...

But I wonder if there is a way to fix them. Thanks for your reply.

Would someone tell me some commands that will mark the bad blocks?
THanks very much.

Don't know how you got this. But did you try and format your NAND? Hard Reset and selecting Volume Down to format device + NAND Storage?

I've tried that but it didn't make any sense.
Thank you all the same!

No sound from main speaker and bad block

hi everyone!
i have a T-Mobile MDA Vario III bought from ebay. no sound from main speaker (audio only with headset or bluetooth)! with mtty (info 8) this is the result:
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 217 (0xD9) is bad block
BLOCK 1215 (0x4BF) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0x9540
Partition[3], type=0x4, start=0xA2C0, total=0x11000
CE Total Length(with sector info) = 0x51B1600
CE CheckSum Length(without sector info) = 0x5160000
rom version is: T.I.R.v11K ITA (the problem emerges also with other roms) and the radio is: 1.65.29.22 (the problem emerges also with other radios).
there are some people who may help me to resolve this situation?
thanks at all!!
marao

Problems during flashing ROM

I had flashed the new WM6.5 whit 1.3 Hardspl and Radio 1.56.70.11 after upgrading i had in the bootloader the messege wlan error. After this i tried mtty task blablabla tried to flash original rom spl1.2 ecc. but it dont work, firstly. Sometimes nothing responds during flashing. Than evryting worked perfectly, dont know why, but now i have some strange output on mtty:
Cmd>task 32
Level = FF
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 433
Storage Total block: 503
Total Bad Block in CE: 0
NeedToEraseBlockStart: 446
NeedToEraseBlockEnd: 936
Storage format success
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is BAD block !!!
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x18100
Partition[3], type=0x4, start=0x1B100, total=0x1F700
CE Total Length(with sector info) = 0x36F8800
CE CheckSum Length(without sector info) = 0x3620000
Can someone help pls..??
Sry by my bad english..
Greets

Bad Blocks in NAND, need help

I'm hoping someone can help me out, I would like to salvage what is now TILT #2 (so I can start messing around in the kitchen) since I picked up a poor specimen for the use of it's system board so I could get rid of the BB Pearl my work handed me. That said I can flash a smaller rom to the system but anything over 80-85 megs throws a 226 error. So I followed the advice given by JockyW to check the memory and below is the output and I'm sure the source of my problems.
I would like to be able to mark the bad blocks so they are not used anymore or recover them if possible.
Cmd>rtask a
POWER OFF PMIC VREG_USB : SUCCESS!
C VREG_USB : SUCCESS!
ECHO ON MODE
rbchk
Checking please wait..
Fond bad block on [0xfd]
****** Total [1] bad blocks******
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
Partition[0], type=0x20, start=0x2, total=0x3E
Partition[1], type=0x23, start=0x40, total=0x580
Partition[2], type=0x25, start=0x5C0, total=0x10B40
Partition[3], type=0x4, start=0x11100, total=0x9980
CE Total Length(with sector info) = 0x8908800
CE CheckSum Length(without sector info) = 0x8880000
Cmd>

Please help! Corrupt NAND? Help with MTTY

Hi, i've experiencing some troubles with my TytnII (no GSM network, then GSM is back but i can hear any sound or call, etc.) and after reflashing ROM and RADIO (several kinds and several times) i still have them.
So i want to clear Nand as deep as possible.
This is the info that i get from MTTY:
Cmd>checkimage
SPL CRC checksum = 0xDF9FA8A7
CE CRC checksum = bad=0x241
0x27BAC496
ExtROM CRC checksum = 0x0
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 289 (0x121) is bad block
BLOCK 1414 (0x586) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0xB4C0
Partition[3], type=0x4, start=0xC240, total=0xF080
CE Total Length(with sector info) = 0x6181200
CE CheckSum Length(without sector info) = 0x6120000
If i make set 16 0 (or set 14 0), and then task 8 i get:
Cmd>set 14 0
HTCST IÚÈÒHTCE
Cmd>task 8
And kaiser reboots but nothing happens, it is not formatted.
Please help !