I had flashed the new WM6.5 whit 1.3 Hardspl and Radio 1.56.70.11 after upgrading i had in the bootloader the messege wlan error. After this i tried mtty task blablabla tried to flash original rom spl1.2 ecc. but it dont work, firstly. Sometimes nothing responds during flashing. Than evryting worked perfectly, dont know why, but now i have some strange output on mtty:
Cmd>task 32
Level = FF
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 433
Storage Total block: 503
Total Bad Block in CE: 0
NeedToEraseBlockStart: 446
NeedToEraseBlockEnd: 936
Storage format success
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is BAD block !!!
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x18100
Partition[3], type=0x4, start=0x1B100, total=0x1F700
CE Total Length(with sector info) = 0x36F8800
CE CheckSum Length(without sector info) = 0x3620000
Can someone help pls..??
Sry by my bad english..
Greets
Related
My kaiser just booting to the bootloader screen and says Serial at the bottom.
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
When I plug in a USB cable it changes the 'Serial' to 'USB'. when I reboot the phone without the USB cable it's going straight into bootloader mode and I can see a quick "missing image file" message then the red/grn/blue screen.
Can someone help me please?
MTTY command info 8 shows:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 566 (0x236) is bad block
BLOCK 1228 (0x4CC) is bad block
BLOCK 1404 (0x57C) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x7800
Partition[3], type=0x4, start=0x8540, total=0x12D80
CE Total Length(with sector info) = 0x42E2A00
CE CheckSum Length(without sector info) = 0x42A0000
GSLEON please help me.
It just sounds like you had a bad flash.
Have you tried re-flashing the ROM on your phone?
Yes. I can flash new rom but i've got the same problem with bootloader.
im experiencing the same problem
disable usb connections on activesync, use mtty, connect to usb, and type "info 8" without the "" and paste the output here, and wait for gsleon3
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 193 (0xC1) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x93C0
Partition[3], type=0x4, start=0xA100, total=0x111C0
CE Total Length(with sector info) = 0x50D0800
CE CheckSum Length(without sector info) = 0x5080000
ok Jocky, here's the new thread
so, after doing the FrankenKaiser on my Kaiser I had the same problem all over again-- my phone restarts infinitely as described in this thread.
GSLEON3 diagnosed it mainly as because of the bad blocks. After doing task 2a it removed 2 of the 3 bad blocks, but even so after ressurecting it with FrankenKaiser it gives me the same problem again. I did another task 2a and it fails on wiping out the bad block:
Code:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 1621 (0x655) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0x7A80
Partition[3], type=0x4, start=0x8800, total=0x12AC0
CE Total Length(with sector info) = 0x4444000
CE CheckSum Length(without sector info) = 0x4400000
Cmd>flashcheck runbadbdk
OS BLOCK Range from:309 852
Bad block num of OS:0
Check OS Done
*******************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
****************************************************************
*****************************************************
Block index 1909 is bad block
**********
****************************************************************
****************************************************************
FAT BLOCK Range from:853 2047
Bad block num of FAT:1
Check FAT Done
Fill RSVD information for block 288 to 309
Storage start sector=0x8800, total sector=0x12AC0
Storage start block=565, total block=1195
Total Bad Block in CE: 0
Erase physical block from 853 to 2032
formatstorage Bad block found: 1909
si backup: Erase physical block from 2032 to 2048
Cmd>task 2a
Format ALL start
backup SPL OK
backup MISC configuration OK
SPL start start block=288, total block of CE=1760
ERASE block 1621 FAIL !!!
Write 0xFF start page=0x4800, total page=0x1B800
SPL version and MFG TAG are same, skip it.
restore SPL OK
restore MISC configuratoin OK
restore MFG configuratoin OK
Format ALL end
as you can see it says ERASE block 1621 FAIL. Any other thoughts from you guys on how to remove this?
It seems that the nand is defective.
Only exception would be if the section with the error is a OTP field.
If there's till guarantee, return it.
If not, only chance could be either :
Jtag and hope that NAND can be repaired, otherwise, buy same nand chip and resolder using hot air workstation.
Cya,
Viper BJK
Here is what I have.
Does anybody know how to fix that?
Thanks very much.
I am waiting online!!!
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 579 (0x243) is bad block
BLOCK 1212 (0x4BC) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x900
Partition[2], type=0x25, start=0xF40, total=0xB080
Partition[3], type=0x4, start=0xBFC0, total=0xF000
CE Total Length(with sector info) = 0x603FE00
CE CheckSum Length(without sector info) = 0x5FE0000
Here is the answer from our master Olipro!
ECC checking is fully integrated into the Diamond SPL, there is nothing you can (or need to) do.
Maybe THIS is useful for you...
But I wonder if there is a way to fix them. Thanks for your reply.
Would someone tell me some commands that will mark the bad blocks?
THanks very much.
Don't know how you got this. But did you try and format your NAND? Hard Reset and selecting Volume Down to format device + NAND Storage?
I've tried that but it didn't make any sense.
Thank you all the same!
hi everyone!
i have a T-Mobile MDA Vario III bought from ebay. no sound from main speaker (audio only with headset or bluetooth)! with mtty (info 8) this is the result:
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 217 (0xD9) is bad block
BLOCK 1215 (0x4BF) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0x9540
Partition[3], type=0x4, start=0xA2C0, total=0x11000
CE Total Length(with sector info) = 0x51B1600
CE CheckSum Length(without sector info) = 0x5160000
rom version is: T.I.R.v11K ITA (the problem emerges also with other roms) and the radio is: 1.65.29.22 (the problem emerges also with other radios).
there are some people who may help me to resolve this situation?
thanks at all!!
marao
Hi, i've experiencing some troubles with my TytnII (no GSM network, then GSM is back but i can hear any sound or call, etc.) and after reflashing ROM and RADIO (several kinds and several times) i still have them.
So i want to clear Nand as deep as possible.
This is the info that i get from MTTY:
Cmd>checkimage
SPL CRC checksum = 0xDF9FA8A7
CE CRC checksum = bad=0x241
0x27BAC496
ExtROM CRC checksum = 0x0
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 289 (0x121) is bad block
BLOCK 1414 (0x586) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0xB4C0
Partition[3], type=0x4, start=0xC240, total=0xF080
CE Total Length(with sector info) = 0x6181200
CE CheckSum Length(without sector info) = 0x6120000
If i make set 16 0 (or set 14 0), and then task 8 i get:
Cmd>set 14 0
HTCST IÚÈÒHTCE
Cmd>task 8
And kaiser reboots but nothing happens, it is not formatted.
Please help !