Related
So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
dew1989 said:
So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
Click to expand...
Click to collapse
It seems that you bricked you phone mate. I think that you installed MrClean rom in a G4 phone so you irrimediably f*cked up the bootloader (IPL and SPL). Many users have reported that their phones were able to boot (and behaved normally) immediatly after the flashing but were dead after they turned them off for the first time, this is what happened to you.
Only thing you can try is going to bootloader mode (but i think it won't work since you messed the bootloader) and then flash a new rom. To do this, press and keep pressed both the keys on the right side and then insert a pin in the reset hole briefly. If the phone goes to the tri-colors screen then you're safe, if not continue reading.
If your warranty perior is not yet over then you can have a new phone for free (DON'T tell them that you flashed an experimental rom!!! Tell only that it went off suddenly or that you were installing an official rom!).
Service centre can repair your device (i suppose they've some method to reflash the bootloader) but i don't know how much they'll ask you.
Try asking other users on this forum. Sorry!
bye
...did you ry to recharge it with the ----ORIGINAL 1A CHARGER----? looks stupid, but i resuscitated mine just before throwing it in the bin. if it works, i will explain you the rest....
yup, I tried charging it with the home charger and still nothing. My battery reads at 3v and it's supposed to be 3.8 so it's not out of juice, but maybe it's just dead?
...you can try with just a normal 9 VDC battery, in order to boost up the voltage, to connect it for a few seconds to the ppc battery till you reach the 3.8 VDC and see if it's working...
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
dew1989 said:
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
Click to expand...
Click to collapse
This is waht you need:
http://www.thetravelinsider.info/phones/cellphonerecharger.htm
This charger is somehow wired weird... it charges the battery AND feeds juice to the phone at the same time (believe it or not, regular chargers and USB cables do not engage until the OS is loaded), allowing you to turn the phone on and in a few minutes plug it into the regular charger to continue charging. Just make sure you get the RAZR tip.
It has saved my ass more than once.
I fixed it , What I did was zap the battery with a 9v battery in 3 sec intervals, I did this about 5 times, then I pluged my phone into the charger and turned it on, the 9v gave it enough juice to boot up and the usb took over from there. So to everyone out there who is having this same problem, try this but don't over zap, check your battery with a multimeter.
im having the same problem----my MDA went dead last night because i forgot to charge the battery and then i went to plug it in the charger but the phone doesnt turn on no more...the light doesnt turn on like if it would be charging and i left it overnight and it still doesnt work..... do yall think that its the battery or is the phone just messed up and cant use it nomore????
Last time I had my battery completely drained, it wouldn't charge from laptop via USB. I read something about how the device's "smart-charging" function itself needs a bit of power to start-up...
but anyways, I couldn't charge the battery through the phone (software charging) - what I had to do was to take a USB cable, cut out one end, identify the +/- (red/black) wires, and charge them directly to the battery's two poles (metal plates). It took about 10-20 seconds of charging until I had enough power in the battery to place it back in the phone, start WM5 and charge it thru the phone.
It would have been much easier if you have a battery charger.
I had my phone connected to the computer through the usb cable, and I just left it connected for a week and it was completely dead and could not be turned on. I don't know how it drained the battery (probally by leaving the wifi on, but the computer was in use all the time). Anyway, thanks to this thread, I used the ac charger and it turned on.
Keywords: t-mobile tmobile mda phone won't don't turn on
phone down
thanks for infos
I'm going to give this a go; a Crossbow ROM flash went horribly wrong last night and in my attempts to repair it (I also must have flashed at least 9 times) the phone went dead. It won't charge either, but battery voltage is 3.7 volts, and I'm sat here wishing it was 3
Will get back to you all!
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Suggestion
CrArc said:
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Click to expand...
Click to collapse
My phone has a hardware problem with the on / off button (doesn´t work at all), at the beggining I thought it was a software problem and I tried all sort of tricks, then I gave up and recognized that was a hardware issue and I found 2 ways to turn the phone on 1) When is totally off (This happens when I have to remove the battery to change SIM card) I connect to the USB cable to my PC or to the car or wall charger and I make a soft reset. 2) When I see the phone signal led blinking I remove the memory card and wakes the phone up (not a good idea since I know that the card is going to get damaged sooner or later).
I just got a G3 wizard from a friend a couple days ago. On Thursday I upgraded it to XDA Mobile 6 and left it on the 2.25.11 (I think) T-Mobile Radio that the T-Mobile 2.26 firmware flash put on it. I used it all day on Friday and then I held the power button and shut the phone completely off for 25 hours, but left it plugged in to a usb to 110V AC adapter that came with my Dell Axim X50V. On Saturday night I went to turn it on and it would not come on no matter what I tried. I found this thread and checked the voltage on the battery directly with a multimeter, 3.13V. I cut the head off a usb cable and then held the black and red wires to the positive and negative terminals on the battery for 2 minutes with the head plugged into a front USB port on my PC. The multimeter then read 3.7V. I put it back into the MDA and it turned on, booted and informed me that the battery was completely drained. I plugged it into the USB to AC charger and it read 10% battery on BatteryStatus. I have left it to charge and it is currently at 60%.
I guess the lesson here is to not totally shut the phone off and let it sit, or the battery won't charge, even plugged into my charger. I guess the OS needs to be running in suspend mode for the charging circuit to run. I know I won't turn it all the way off ever again unless I have my little plug thing and my laptop with me.
(old) Nokia phones have a state called "Acting dead" (from service manuals) which takes place when phone is turned off and battery inserted. It means that the energy is flowing around the board so that the responsible hardware keeps waiting for a 'HIGH' signal ordering to turn ON the phone.
When batteries go bellow the 2.x volts they stop being charged by the phones. This is why i protect the battery terminals with tape when the phone is stored for some time and the reason why a lot of people thinks the phones are broken when not used for months. I usually use the 'freezer trick' where i leave the batteries inside the freezer all night and charge them next day.
just 2 cents...
My Wizard XDA got discharged over the weekend and wouldn't start up - after 12 hours on USB it still wouldn't start.
The charge tips saved my bacon - I modified a USB cable as per the instructions above, and used it to charge up the XDA battery - it only needed five seconds and the phone now boots!
Thanks All, great information!
My 2 cents...
If you're going to try the same, connect red usb to the +ve terminal of your battery and black USB to the -ve terminal of the battery. I'd suggest having a voltmeter to hand to check battery and supply voltage.
Disclaimer - the ablve worked for me, but I'm not responsible for anyone damaging themselves, their PC,their phone or anything else by using the above info!
BUMP! thought my phone was dead, hacked a USB cable and i'm back in business!!!!
TYTN II won't turn on
i left it plugged in all day and when i tried to turn it on it didn't respond. i have a second battery that was fully charged and that didn't work either. i tried a hard reset with it unplugged and with it plugged into the charger. nothing works. i'm on the standard at&t rom with lots of programs. i got it unlocked so i can't go to at&t.
Chaps
Yesterday my 6515 stopped cooperate with me! Totally!
- I didn't dropped him or physically damaged,
- The battery was charged in 85% just before it was switched off itself
- Back cover closed with no gaps between cover and body
- Was fully functional when suddenly switched off
- I didn't upgraded anythihng before.
Symptoms:
- Ipaq is not reacting on start button
- Not reacting on reset
- Not reacting on hard reset
- The left diode blinking red during charging via usb cradle when I’m pressing power up button
- The same happens with regular charger
- During charging with regular charger when I’m opening the back panel the diode stop blink and become flash continuously in red.
I have already tried almost everything to start it up:
Changed the battery,
Open, close the back battery panel
With and without SD card
Appreciate any HELP!
small update
Ok I have made some progress..
Now I can see the bootloader screen and that's it.
What to do next ???
Im not sure what blinking red means but when you remove the backcover, the red led will lite up.
Try to do a hard reset, and see if it restarts without going to bootloader. Otherwise, you will probably need to upgrade the firmware from the bootloader screen. Download the latest rom updates from hp.
cluurk said:
Im not sure what blinking red means but when you remove the backcover, the red led will lite up.
Try to do a hard reset, and see if it restarts without going to bootloader. Otherwise, you will probably need to upgrade the firmware from the bootloader screen. Download the latest rom updates from hp.
Click to expand...
Click to collapse
Thanks for reply
Indeed! When I opened back cover the led become flash continuously!
I have tried to apply the rom update from HP unfortunately all of the updates have to be done through Active sync!
It is impossible in current situation because of pressing Power+Joystick+Reset the ootloader screen appear but then nothing This is happens only when PDA is charging with regular charger. Using USB charge or battery power I can't even start the bootloader screen.
From where can I download the SD bootable image or how to make it?
And again small step ahead:
Hi
And again small step ahead:
In craddle there is another input for power so I managed to power it up and connect.
I had to switch of firewall (otherwise i have error 601 - unable to connect the device or something simmillar) and reinstall Active sync back to 3.8
Got bootloader screen USB and hp logo and v 021
by running romupdate utility downloaded from hp site ( whatever the version is ) I finally recognized my model version: it is 6515c
Next
Found valid version from HP site for 6515c ( i think 1.21) and successfully upgraded. No breaks, no other issues just successfully uploadede into finish.
Then hard reset and......
The system starts, screen flashes up, system start loading and the screen fading out. ... and again ..... and again ...... and again and the nothing!
I have tried again to pull out back cover, remove batery, put it back after some time, place back the cover and again.
Nothin' Nada Null %$#@%!$#ing piece of junk.
BTW it is happening only where PDA it is connected to AC power. On battery system is not booting, no booloader nothing!
Any suggestions? Pleeeeeeeease!
After you upgraded the firmware and it started up, was this done with the pda on AC or battery power? If its on battery and it starts fading, your battery is probably screwed. Did you also know there are 2 batteries in the IPaq?
Oh and if its a battery problem, you will need to leave the battery+pda connected to the AC for a while before it can startup and probably into booloader. Run your firmware upgrade again and power it on with the AC connected! If it boots up fine, then monitor the battery status bars in the Power settings and see if both the LiIon and NiMh batteries are holding charge. Hopefully from here you can find a dead battery.
Another thing you could try is to reset the battery when in bootloader mode once you are certain its the battery
http://blogs.unbolt.net/index.php/brinley/2006/08/02/howto_reset_discharged_battery_for_ipaq_6515
Battery reset? Could might be the issue?
Hi
I really appreciate your response.
The whole upgrade and the other stuff have been done with inserted battery and AC connected.
I plugged the PDA into the cradle which was connected to PC via USB and I plugged also AC into the cradle AC input.
It is fading just after reboot only when the iPAQ is connected to AC power (of course battery is inserted otherwise it will not startup anyway.)
On pure battery power it doesn’t giving any signs of living whatever button has been pressed.
The link you provided might contain very valuable directions to me. The man is learning within whole life and dying still being stupid.
I thought that I read the info from the site you suggested but I probably missed the meaning of the post regarding battery reset. That might be this. I will check and update you very soon.
I did the steps from above link. The iPAQ rebooted, started to load the os and again faded out….
Question to everybody:
During bootloader screen appear should I have any diode flashing blinking or whatever
I’m asking because of mine is blind!
Nothing is flashing, blinking, beaming or shining. Just two, completely dead diodes.
Hi, I've just found out what flashing red means
"green blinking means GSM coverage, yellow blinking - missed reminder or alarm clock signal, permanent yellow - recharging, green - the battery is full, red blinking means greatly discharged battery, pale blue blinking - Bluetooth is on"
I think one of your batteries is dead, and if you have already replaced to LiIon battery then you'll probably have to try to replace the NiMh one inside. I cant think of anything else to try
Battery????
Damn!
I think I have a hardware problem! I have 2 batteries: one brand new and the old one. Both not working! Moreover they're not charging! They suppose to charge when I put PDA into the craddle or directly plug to AC charger but they aren't.
No diode is flashing during charging. Damn.
I will try to borrow one battery from one of my friend just to check if this is it!
I will let you know later on.
If I recall correctly, the charging led does not light up in bootloader mode. I maybe wrong though. I think you should try to check the voltage in the LiIon battery to determine if they are being charged.
Also you never mentioned checking the backup NiMh battery. I believe that the NiMh battery is required to power up of the ipaq as well so it may be the cause of your ipaq dying after starting up.
NiMh backup battery
Fortunately I know someone who can charge the battery for me. There will be no problem with that.
From the other side I'm worry about the phone charging....
Why I can't charge the battery using iPAQ?
Next you mentioned about "NiMh battery". I'm sorry for my ignorance but what is that?
Is it secondary battery ?????
Is there any way to charge or replace it? Is it pluggable battery? Where is located?
Yes there is a secondary battery. However, I do not know where it is either.
Here is an example from a different PDA
http://paulstravelpictures.com/HP-iPAQ-HX4700-PDA-Backup-Battery-Replacement-Guide/index.html
If you want to open up your IPAQ do it at your OWN RISK!
cluurk said:
Yes there is a secondary battery. However, I do not know where it is either.
Here is an example from a different PDA
http://paulstravelpictures.com/HP-iPAQ-HX4700-PDA-Backup-Battery-Replacement-Guide/index.html
If you want to open up your IPAQ do it at your OWN RISK!
Click to expand...
Click to collapse
You don't need to touch that one, this battery is designed for save your data when you exchange the main battery.
commanddos said:
Damn!
I think I have a hardware problem! I have 2 batteries: one brand new and the old one. Both not working! Moreover they're not charging! They suppose to charge when I put PDA into the craddle or directly plug to AC charger but they aren't.
No diode is flashing during charging. Damn.
I will try to borrow one battery from one of my friend just to check if this is it!
I will let you know later on.
Click to expand...
Click to collapse
Commadnnos,
Sound like your 6515 has battery charging problem. If the charging failed, even you have brand new battery, it won't be charged at all.
Since you have two batteries, you might want to buy a external battery charger to prove those two batteries are good.
I think the charge circuit is in the second PCB board which under the keyboard inside your 6515; if those batteries are good, you might want to buy a dead 6515 and replace it by yourself...
Cheers,
watchsat said:
Commadnnos,
Sound like your 6515 has battery charging problem. If the charging failed, even you have brand new battery, it won't be charged at all.
Since you have two batteries, you might want to buy a external battery charger to prove those two batteries are good.
I think the charge circuit is in the second PCB board which under the keyboard inside your 6515; if those batteries are good, you might want to buy a dead 6515 and replace it by yourself...
Cheers,
Click to expand...
Click to collapse
Well Well Well ..... it is getting wormer. Many thanks to everyone who are still trying to help me out. Thanks again.
Is that mean the secondary battery is located under the keyboard? I saw the photos from unassembled 6515 and it looks like the secondary battery. To replace it you have to first remove 3 screws, unplug the LCD and remove whole main board.
Is that means that the charging circuit has been built in the keyboard plate?
Thank You all. Patient died......
I would like to thank everyone for help. I think we can close this thread over here.
My beetle just went out into the "digital heaven".
The HP support specialist ensured me (without any tips or hints from my side) that mainly there is a problem with passing the power from the charger to the battery which means no more no less like ".... dude your motherboard is screwed. You have to get the new one or whatever...!"
So now it is a time for selling the rest of the parts on auctions......
R.I.P (Rust In Peace)
if the red light blinks
1 your battery has problem
or
2 your battery cover has problem. The plastic part on the back of your battery cover may have broken which touchs the microswith on the mainboard.
if that microswitch is not triggered , the hw65xx,hw69xx will not turn on.
went to charge phone and i know i am gonna get slammed but i am phreaking out the phone will not charge, did hard reset soft reset reinstalled rom etc...nothing helps please help me now its below 50% so cant flash back old firmware
tqg317 said:
went to charge phone and i know i am gonna get slammed but i am phreaking out the phone will not charge, did hard reset soft reset reinstalled rom etc...nothing helps please help me now its below 50% so cant flash back old firmware
Click to expand...
Click to collapse
Have you tried to plug in a usb to your computer to see if it can pull off a charge? Might work...
Ron
mark43 said:
Have you tried to plug in a usb to your computer to see if it can pull off a charge? Might work...
Ron
Click to expand...
Click to collapse
That will most likely NOT work. The USB charge off a PC is a trickle charger. First, if the battery is completely drained, take out the battery and plug it into the wall charger. Let it sit like that for about 15 mins. Then put the battery in and let it charge over night. If it still will not power on the device is probably bad.
Are you getting a red LED on the front? If so it could be the "red light of death" (RLOD). It is a known issues that has caused many kaisers\tilts to fail.
marm0lade said:
That will most likely NOT work. The USB charge off a PC is a trickle charger. First, if the battery is completely drained, take out the battery and plug it into the wall charger. Let it sit like that for about 15 mins. Then put the battery in and let it charge over night. If it still will not power on the device is probably bad.
Are you getting a red LED on the front? If so it could be the "red light of death" (RLOD). It is a known issues that has caused many kaisers\tilts to fail.
Click to expand...
Click to collapse
actually it might work.....there has been cases where there's damage to the usb port and it wont charge with a wall charger, but fine when connected to a pc via usb cable (or it might be the other way round). the rlod is a different issue, this one seems to be more of a usb port issue. tqg317, take a look at your usb port and see if you can spot any damage.
Moving to the regular Kaiser Forum. Not an upgrading/development matter.
Mike
99% of the time a damaged USB port will affect USB to PC or automotive charging only. Take a look at your USB port, if it is curved or lowere on the right side then YOU placed the stylus poorly during a soft reset. You may be able to straighten it out using your stylus, but do it very carefully.
thanks for the move
i guess what i am wondering is if i get the right things to set it back to att and ezxchange it, it gets no charge large or anything, usb, ac, or car dc thanks for everyone help
ok
got all the things for reverting back to at&t i imigine i can use the origina att rom but what about the original att spl can it be ran off a microsd card?
Shortly: I flashed a new rom (not so new... Mameli 2.0 with WM6.1) and the upgrade process stuck on 99%, computer saying "All Done"
No so... trying to reboot the Wizard gets up the bootloader screen... no problem, will you say BUT... I was in a hurry so I leave the USB cable connected and go away for a few hours (I suppose the USB cable may keep powered the device but now I guess no... )
So, when I came back, the Wizard was turned off.
First try was soft resetting the device with no success: screen remains black.
Then I try to connect the power supply and nothing happened...
Then I pull off the battery and keep it off for a few seconds... I was googling with the device in this state when the bootloader screen pops up for not more then 15 seconds then blank again...
No way to enter bootloader mode or to hard reset the device...
I suppose the battery goes almost flat... and I've not a cradle... is there any way to charge the battery? or a way to build up a cradle-substitute?
May be the issue due to battery flat?
Thanks, Pino
Try plugging in to the original charger, not a USB cable, with the power off.
After about a minute you should see the orange LED turn on.
At least that has worked for me when my battery has been dead.
Nothing... It was already done... I suppose the charging doesn't happen if the OS didn't load... even if I read about some stating that if the charger supplies 1.0A the charge happens...
Now I'm trying to charge the battery with "alternatives" methods...
Thank you for your interest
and so?!?!?
So much lurking... noone writing?
Ideas welcome....
I've done something similar to this too, i.e., where battery gets so low that phone cannot start charging cycle.
Here is what I have done. Take note on the battery of the positive and negative terminals (clearly marked on battery). Use a regular 9V battery and some wire (or 9V connector) and connect the 9V to the phone battery (+ to + and - to -). Allow the phone battery to recharge some from the 9V. I suggest connecting for about 1 minute or so and then disconnecting again for 1 minute or so, and repeat this cycle a dozen times or (or more) using this 50% duty cycle charging. (not sure about charging current, nor heating of battery and don't want to overheat or damage the phone battery).
After giving the phone battery some (re)charging, then try plugging phone in to see if charging cycle comes on. (try first without trying to turn on the phone. If no response then try turning phone on while plugged in to USB). Generally makes no difference whether using USB plugged into computer, original charger or after market, ... phone does not, nor cannot discriminate between different 5V 'USB' sources.
If this doesn't work then the next step is to carefully touch the 9 V to the battery while in the phone and connected to USB (and to play this safe use charger, and not computer USB ... don't want to risk damage to computer). I would only try this if you feel extremely comfortable with electronics and voltages (albeit this is very low voltage) and as a last resort. KEEP IN MIND YOU WILL BE DOING THIS AT YOUR OWN RISK, and I don't want to be blamed for anything that may go wrong with the phone or otherwise by you trying this. This has worked for me on several occassions, but I am an engineer who has experimented with electronic ciruits off and on for 16 + years and so feel comfortable doing stuff like this. (again remember + to + and - to -, battery to battery).
Good Luck
First of all... Thanks for replying...
The problem isn't due to battery too much empty (it's a frequent issue, with mobile phones too...)
I suppose the Wizard needs be correctly initialized to start charging the battery and mine was in bootloader mode.
Sometimes I am able to power up the system for a little while and the bootloader screen appears but the battery doesn't charges so I cannot disconnect the power supply... this is why I suppose I'd get better times if I got a cradle.
Now I'm trying to arrange a flying connection between the battery and my kaiser's desktop charger to give the battery a bit of charge and verify my ipotesys (uh-oh... it's correctly spelled? sorry for my bad english....)
OK, wish me luck
stay tuned...
OK, no more bricked
The issue, as I supposed, was due to a flat battery!!!
I tried unsuccessfully to charge it back using the external charger for my Kaiser, probably the unsuccess was due to difficult to obtain a stable contact between charger pins and battery leads...
After that I remembered I had another battery. It wasn't used for a bit of months (I use the wizard just as backup, when the Kaiser is out of order) but luckily I stored it full charged so the battery was able to make my wizard power up (strange thing, I needed to keep the power button pressed as the device powers down as soon as I release the button!!!)
I tried to update the rom again but it failed at 99% so now I reverted to an old rom but the device is still alive...
Maybe I'll try again the update but not before having fully charged both batteries
See You and thanks to everyone tried to help...
Pino
Hello, I've been using my htc vivid since about march last year, and I recently rooted it, flashed Kanbang and added wajee's desensed rom. Things have been going smoothly until recently, I attempted to change roms to xperiense (Also by wajee) and I'm now stuck booting up at the splash screen, I can access my boot loader, but I can NOT preform a factory reset, Please, if anyone here can help me I would seriously appreciate it.
If the recovery program is not showing then you need to clear the catch if the recovery still don't work try to reflash the recovery or even a different recovery . If that don't work relock the bl and run the stock ruu and start over , the hansoon tool kit makes this a breeze and you will be back where you where in a few minutes.
I can access the bootloader, and I forgot to mention that If I plug it in to my comp it does not seem to want to charge, it shows the light for about 5 seconds, then the capacitive buttons will vibrate if pressed, but nothing displays, I have to boot into the bootloader without it plugged in then plug it in.
Yea pull the batt and boot into hboot , then select fastboot plug the phone then it should say fastboot USB , running the ruu will fix any errors you have so you can start fresh ....just remember never pull the plug while the ruu is running .
Well, Thanks for trying to help, but the batter will NOT charge and is dead, I'm ordering another OEM battery soon, Thanks for the help but I've read and this actually appears to be the problem, again thanks you for trying to help.
No problem , if ya need anything don't hesitate to ask here someone can always help out .
Are you sure the battery is kaput? Have you tried charging it with a wall charger? HBOOT doesn't support charging BTW, and USB won't charge unless the phone is ON and in the OS (or in TWRP recovery which DOES support charging).
Pull the battery and leave it turned off, then plug in the wall charger. You should get an orange LED and presto, it's charging. See if you can power up after an hour or two. If it spends two hours on the wall charger and still isn't charging, then it's either A) your battery, or B) Your charge port. I had the charge port die on my blackberry torch. Thought it was the battery too until I borrowed one from a mate and swapped things around.
ess.boyer said:
Are you sure the battery is kaput? Have you tried charging it with a wall charger? HBOOT doesn't support charging BTW, and USB won't charge unless the phone is ON and in the OS (or in TWRP recovery which DOES support charging).
Pull the battery and leave it turned off, then plug in the wall charger. You should get an orange LED and presto, it's charging. See if you can power up after an hour or two. If it spends two hours on the wall charger and still isn't charging, then it's either A) your battery, or B) Your charge port. I had the charge port die on my blackberry torch. Thought it was the battery too until I borrowed one from a mate and swapped things around.
Click to expand...
Click to collapse
I've left it charging for about 1 and a half hours and the led goes on briefly the shuts off after a little, the phone won't go into hboot now
If you want I can send you my battery fully charged and send it back after we figure out if your battery is bad , I don't use it I have two extended packs I use just lmk .
Bigtjmc said:
If you want I can send you my battery fully charged and send it back after we figure out if your battery is bad , I don't use it I have two extended packs I use just lmk .
Click to expand...
Click to collapse
Thanks for the offer but I have a bro with the same phone who lives nearby so I'm going to see if I can borrow it tomorrow for a few minutes, if it works, my new batter is in the mail, if not, I'm going to talk to at&t and see if I can get the phone replaced.
It keeps claiming I have the wrong version (The Ruu) any chance of a link to the most up to date one?