Sd card flashing method don't work - P3600 Software Upgrading

hi all , i've tried to flash my trinity (s300) by wmdc under vista 64 but don't work ,also with trinity guides instructions ,( error 260)
So i have tried with Active sync under XP proS2 but don't work too ,same error
And then i have tried Sd card method described on wiki ,but when i put the phone into bootloader it doesn't read TRINIMG.nbh
So i need your help , why i can't upgrade ?
is SDHC card causing this problem ?
Before i was enable to upgrade my phone ,my actual rom is Shap's
Help me please

please close this thread ,
Solution found ,thanks

1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
If not work
copy all file too SD
Run enterbootload
work 100%
First Unlock your CID

doesn't work
khalid1210 said:
1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
If not work
copy all file too SD
Run enterbootload
work 100%
First Unlock your CID
Click to expand...
Click to collapse
Got same problem. Still doesn't work after copying all files.

orenroot said:
Got same problem. Still doesn't work after copying all files.
Click to expand...
Click to collapse
wich card ar you using? I know only non sdhc card do the trick and formatted ....fat or fat 16.. do some search goooooooooooooooogle..

[email protected] said:
wich card ar you using? I know only non sdhc card do the trick and formatted ....fat or fat 16.. do some search goooooooooooooooogle..
Click to expand...
Click to collapse
Non SDHC. Formatted to FAT32 as a post in the forums said. I've tried Sandisk and transcend since someone mentioned transcend has issues.
It can read the card from the OS, but it doesn't leave the bootloader.

Related

Really need help !!

Sorry for posting this new thread but it was really important for me to do so.
I have a problem regarding flashing a rom.
I have flashed a lot of roms recently through sd card method but never had a problem.
I flashed ' smabergs ' ' Touch X ' Rom 2day but during the update . it stops at around 80% update.
so i have not been able to move to any rom. or more precisely... My phone hasnt been of any use since then i dont have a spare one.
Please help guys. any help is much appreciated !
hi
take your card out and formated with your computer as fat32 it might be correpted
try gain with SD card method if not
use hard SPL method
Use the computer in tow steps and keep your mobile linked while you do the hard SPL flash and uploading the ROM with RUUtility_Kovsky
1 - Downloads the hard rest program X1_HardSPL_v1from xda and unzip
2 - Download the flash utility RUUtility_Kovsky from xda and unzip
Installation, remove the SD card from your mobile it might be corrupted
To lode the ROM to your mobile in tow steps
1- Flash your mobile with X1_HardSPL_v1click the EXE file this will take less than 5 minutes watch your mobile screen and press yes to add a small ROM
2- Don’t remove your mobile USB
3- IMPORTANT you have to copy the new ROM .nbh inside the ROM utility folder called RUU_Kovsky, select ROMUpdateUtility.exe its located inside the folder RUU_Kovsky and pres the ROMUpdateUtility.exe , and start upload your ROM ,this will take less 10 minutes
Put back your formatted SD card
Thanx
thanx for your help bro. but i still am not able to properly understand your methods.
Please explain them in a little brief and please provide the links for ruu_kovsky
It's a request.
bassam said:
hi
take your card out and formated with your computer as fat32 it might be correpted
try gain with SD card method if not
use hard SPL method
Use the computer in tow steps and keep your mobile linked while you do the hard SPL flash and uploading the ROM with RUUtility_Kovsky
1 - Downloads the hard rest program X1_HardSPL_v1from xda and unzip
2 - Download the flash utility RUUtility_Kovsky from xda and unzip
Installation, remove the SD card from your mobile it might be corrupted
To lode the ROM to your mobile in tow steps
1- Flash your mobile with X1_HardSPL_v1click the EXE file this will take less than 5 minutes watch your mobile screen and press yes to add a small ROM
2- Don’t remove your mobile USB
3- IMPORTANT you have to copy the new ROM .nbh inside the ROM utility folder called RUU_Kovsky, select ROMUpdateUtility.exe its located inside the folder RUU_Kovsky and pres the ROMUpdateUtility.exe , and start upload your ROM ,this will take less 10 minutes
Put back your formatted SD card
Click to expand...
Click to collapse
Thanx dude. M through now
hi , are you don , if so install this rom, the best
http://forum.xda-developers.com/showthread.php?t=509891
most probably:
1- you don't have HARD-SPL correctly flashed
OR
2- the ROM you are flashing is corrupted (bad download or bad decompression or bad copy to the microSD)
PS: with the stock SPL you can still flash STOCK ROMS
WHAT TO DO ??
1- remove the microSD card and insert it into a PC (with an adapter or reader)
2- delete the current kovsimg.nbh file
3- CHECK the microSD for errors (right click -> tools -> scan disk or check disk)
4- COPY A STOCK ROM to the microSD and rename to kovsimg.nbh
5- Insert the microSD back into the phone, go to bootloader and flash
6- ENJOY YOUR PHONE AGAIN

TREO 750 "beta testing expired"

Hi, this is my first post on this forum and i'm hoping to get some help to solve my problem.
I have an unlocked ATT treo 750 that i'm currently using with T-Mobile. I was happily running windows 5 and decided to try this new windows mobile 6.5 so i downloaded the rom from a thread on this forum and i ran the update process while my phone was connected to windows zync porgram, so it worked fine, but as soon as i rebooted my phone to the new windows 6.5 it gave me the
"This concludes de beta test of this software release...." now i try to reconnect my phone to my pc to zync and flash another rom but i won't recognize the connection.
what can i do, i know there is a way to flash a rom using your mini sd card but i'm not sure about this process....tell me if i have it right:
1. format your mini sd card using fat32, using a computer with a card reader (i can't format it using my phone cause of ovious reasons)
2. copy the rom image to the mini sd card on the root folder. the rom image should be in .nbh format. (i have a rom called CHEEIMG.nbh by Navenedrob)
3. re-insert the mini sd cad to the phone.....I DONT KNOW WHAT DO AFTER THIS, and what do you mean by HARD SPL or SPL... is it a file i should copy along with the CHEEIMG.nbh file in the mini sd card????
PLEASE HELP ME.. what buttons do i press on my treo 750 to trigger installation...?????
thanks
Hello there if you look a couple of threads down on main form page there's a post by Navenedrob who gives step by step instructions on how to sucessful complete the whole process
I did it about 2 weeks ago as a newbie and it very easy to follow very good update
Also make sure you download and use his WM6.5 ROM. No expiration date ...
hlopez said:
Hi, this is my first post on this forum and i'm hoping to get some help to solve my problem.
I have an unlocked ATT treo 750 that i'm currently using with T-Mobile. I was happily running windows 5 and decided to try this new windows mobile 6.5 so i downloaded the rom from a thread on this forum and i ran the update process while my phone was connected to windows zync porgram, so it worked fine, but as soon as i rebooted my phone to the new windows 6.5 it gave me the
"This concludes de beta test of this software release...." now i try to reconnect my phone to my pc to zync and flash another rom but i won't recognize the connection.
what can i do, i know there is a way to flash a rom using your mini sd card but i'm not sure about this process....tell me if i have it right:
1. format your mini sd card using fat32, using a computer with a card reader (i can't format it using my phone cause of ovious reasons)
2. copy the rom image to the mini sd card on the root folder. the rom image should be in .nbh format. (i have a rom called CHEEIMG.nbh by Navenedrob)
3. re-insert the mini sd cad to the phone.....I DONT KNOW WHAT DO AFTER THIS, and what do you mean by HARD SPL or SPL... is it a file i should copy along with the CHEEIMG.nbh file in the mini sd card????
PLEASE HELP ME.. what buttons do i press on my treo 750 to trigger installation...?????
thanks
Click to expand...
Click to collapse
Hi,
I'm sorry, I wrote that tutorial for people who couldn't use HARD SPL (A piece of software that lets you flash the phone) to get Windows Mobile 6.5.
Try formatting the memory card to FAT32 using a card reader, then from your computer, download the ROM here and paste it onto your memory card (ROM Link- http://forum.xda-developers.com/showthread.php?t=541417 ).
Load the memory card into the phone.
Where you've just loaded the memory card, there is a Reset button. It's tiny, and its located where the memory card slot is.
On the other side of the phone is the Media Button. It's the one below the volume buttons. Hold this button down and press the Reset key with your stylus.
The screen should load into the "Bootloader" mode and try to scan your memory card. If it recognises the CHEEIMG.NBH file, it will ask you to press the Call End key and then go on installing itself (I hope).
After saying all this, please note that I'm not an expert and had to experiment. I didn't however brick my phone with a Beta release so I'm giving you this in the hopes that it will work.
Just make sure you have the CHEEIMG.NBH file. It may have a different filename (anything that comes before .nbh), you just have to rename it.
Secondly make sure your card is formatted to FAT32. Google it if you don't understand or if you don't know how. I use a mac so formatting is easy.
Thirdly, familiarize yourself with starting up in Bootloader mode.
Have a play, I hope this helps.
eD

Couldn't flash

i have a tilt 2 and i've tried everything to flash it and it wont work, i think that i have given up on it. unless there is something else i can do
have you done a HARD-SPL
ix sik pro xi said:
i have a tilt 2 and i've tried everything to flash it and it wont work, i think that i have given up on it. unless there is something else i can do
Click to expand...
Click to collapse
Try this it worked for me too...http://forum.xda-developers.com/showthread.php?p=4696049&highlight=enable#post4696049
bmikerecords said:
have you done a HARD-SPL
Click to expand...
Click to collapse
yup, then when i use CustomRUU it tells me there is an error. i have exited and retried it with different usb cables and still gives me the same error
ix sik pro xi said:
yup, then when i use CustomRUU it tells me there is an error. i have exited and retried it with different usb cables and still gives me the same error
Click to expand...
Click to collapse
Flashed using the micro sd card..its much safer and faster...
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, Hold volume down and press the reset button, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
jhernand1102 said:
Flashed using the micro sd card..its much safer and faster...
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, Hold volume down and press the reset button, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
i wanted the energy rom 23554, where are the files you are talking about?
Edit: never mind, found the file. copying right now
it worked!!! thanks guys
Resolved

Can we flash from an sd card on the Blackstone?

I looked and can not find things mentioning via sd card only via PC. If I am wrong, I am sorry but I didn't find it. Could you attach a link to where it mentions it? What do I name the .nbh?
Yes you can, the image needs to be called BLACIMG.NBH
and you need hspl on youre phone and the mem formatted to fat 32:-o
miniterror said:
and you need hspl on youre phone and the mem formatted to fat 32:-o
Click to expand...
Click to collapse
I just received it today from ebay, does this seem to be already for me to flash it?
It has 6.1 installed
Bootloader screen says
BLAC100 32M
SPL-1.56.OliNex
MicroP-BlackStone (LED) v6
Bootloader says "No Image File"
I have the BLACIMG.nbh file on my 1GB card and it's not loading it. I have done it the same way on my HTC Jade multiple times with the same sd card.
I TRIED WITH ANOTHER ROM AND IT WORKED JUST FINE. I don't know what was wrong with the other one but Thanks for everyone's help.
I'm afraid you're not following the right procedure. This should do the job.
1. Copy BLACIMG.NBH into the root dir of your Storage Card.
2. Be sure to have at least 30% of charge.
3. Turn off your device . Fully power the device off by long press of power key.
4. Go to bootloader mode. Push and hold Vol Down + press Power button.
5. As soon as presented the message, push Power button to start flashing or Volume Down button to cancel.
6. The whole procedure will take about 3 minutes. After you finish and see the relative message, soft reset your device, you are ready.
Make sure you formatted your sd-card.
To enter Bootloader, starting from powered off phone, hold down volumebutton and briefly press powerbutton.
You can also always use the "search" funtion on the forum startpage. Topbar (brown) on the right side.
It's recommendable to hardreset your device after flashing.
Good luck.
Bry009 said:
I'm afraid you're not following the right procedure. This should do the job.
1. Copy BLACIMG.NBH into the root dir of your Storage Card.
2. Be sure to have at least 30% of charge.
3. Turn off your device . Fully power the device off by long press of power key.
4. Go to bootloader mode. Push and hold Vol Down + press Power button.
5. As soon as presented the message, push Power button to start flashing or Volume Down button to cancel.
6. The whole procedure will take about 3 minutes. After you finish and see the relative message, soft reset your device, you are ready.
Make sure you formatted your sd-card.
To enter Bootloader, starting from powered off phone, hold down volumebutton and briefly press powerbutton.
You can also always use the "search" funtion on the forum startpage. Topbar (brown) on the right side.
It's recommendable to hardreset your device after flashing.
Good luck.
Click to expand...
Click to collapse
I got it to work just fine I used another ROM and it worked just fine. I have also had success with my JADE with no problem. I edited the post before stating what I did to get it to load successfully. Thank You for the assistance though, that is a easy step by step tutorial of how to perform the flash from sd.
I got a kingston card (8gb) it works perfect but for some reason I cant flash from there... I use my backup 2gb scandisk
jimi_c said:
I got a kingston card (8gb) it works perfect but for some reason I cant flash from there... I use my backup 2gb scandisk
Click to expand...
Click to collapse
you're right, this trick will not work with SD-HC cards, only "normal" SD-Cards will do the job
SD card flashing
kel187 said:
you're right, this trick will not work with SD-HC cards, only "normal" SD-Cards will do the job
Click to expand...
Click to collapse
I have a 16 gb MicroSd-HC (Sandisk) and regularly flash blacimg.nbh files from this card. Never had any problems. My phone has hardspl and is secuurity unlocked courtesy Olipro
This has been covered many times before in wiki and stickies. Thread closed

Help!!!!! Flash topaz problem!!!

Hello. I have two TOPAZ devices, which both have been flashed with a custom ROM. I flashed them around 2-3 months ago. When i tried to turn one back to WM 6.5 Original, it got bricked. So :
1. Can a TOPAZ be restored to the original factory state?
1.1 If yes, how?
2. Is there anyway to unbrick a TOPAZ?
3. Should this be 4?
Excuse my english
Thanks,
Mike
Bricked??? Lets see... To flash the original ROM, do the following:
1. Extract the original downloaded ROM-file (should be an self-extracting .exe file).
2. Copy the extracted .nbh-file to the root of your sdcard and name it: TOPAIMG.nbh.
3. PowerOn phone holding the VOL-DOWN key pressed until Rainbowcolorscreen apears.
4. Press Power to start internal flashing.
5. After flashing, Softreset...
Thats it... if one of these steps fail, please describe exactly what is happening.
Greetz DN
WOW man!! That WAS a fast reply, thanks. I am at work right now, so I can't do much although, how do I extract the rom?
"2] Format your SD card into FAT32:
- go into dos and type:
format <volume> /FS:FAT32 /A:4096
3] Run Qmat to create a gold card:
- Put the formatted microSD card in the working WM device and connect via ActiveSync
- Run Qmat, Go to Hardware Forensics and select 'Generate HTC Goldcard'
- Select your bricked device's key
- Get the SD Card Serial from WINCE Device
- Save the Goldcard image to the SD Card
Now you have a SuperCID which allows you to flash any shipped ROM"
*thats from the sticky under unlocking/flashing*
Scabes24 said:
"2] Format your SD card into FAT32:
- go into dos and type:
format <volume> /FS:FAT32 /A:4096
3] Run Qmat to create a gold card:
- Put the formatted microSD card in the working WM device and connect via ActiveSync
- Run Qmat, Go to Hardware Forensics and select 'Generate HTC Goldcard'
- Select your bricked device's key
- Get the SD Card Serial from WINCE Device
- Save the Goldcard image to the SD Card
Now you have a SuperCID which allows you to flash any shipped ROM"
*thats from the sticky under unlocking/flashing*
Click to expand...
Click to collapse
thanks for the quick responce. so let me get this straight,
: i format my MicroSD
I connect it to my PC and with Qmat I Generate an HTC Goldcard
*didnt get this part* my bricked device's key? how do I do that?
then I use WINCE to get my serial(sdcard)
and now save the goldcard image to sd.
Is this correct?? thanks
Now, after i follow these steps, how do I flash the rom? same way as usual, or is it a special method?
and last, this is for unbricking?
Thanks again.
btw will the method in post 2 work for a fullyworking custom ROM device?
It seems like its basically just allowing you to connect your phone - enter bootloader - and run the .exe (TopazRUU) from your computer to flash a stock rom.
you should read the post in the first sticky, then look at "unlocking/flashing" and you will see #5 Unbricking
thanks
Is your problem solved?
yes, it is!! thanks everyone
Problem Solved - Closed Thread

Categories

Resources