Database Develop

Sd card flashing method don't work

hi all , i've tried to flash my trinity (s300) by wmdc under vista 64 but don't work ,also with trinity guides instructions ,( error 260)
So i have tried with Active sync under XP proS2 but don't work too ,same error
And then i have tried Sd card method described on wiki ,but when i put the phone into bootloader it doesn't read TRINIMG.nbh
So i need your help , why i can't upgrade ?
is SDHC card causing this problem ?
Before i was enable to upgrade my phone ,my actual rom is Shap's
Help me please

please close this thread ,
Solution found ,thanks

1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
If not work
copy all file too SD
Run enterbootload
work 100%
First Unlock your CID

doesn't work
khalid1210 said:
1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
If not work
copy all file too SD
Run enterbootload
work 100%
First Unlock your CID
Click to expand...
Click to collapse
Got same problem. Still doesn't work after copying all files.

orenroot said:
Got same problem. Still doesn't work after copying all files.
Click to expand...
Click to collapse
wich card ar you using? I know only non sdhc card do the trick and formatted ....fat or fat 16.. do some search goooooooooooooooogle..

[email protected] said:
wich card ar you using? I know only non sdhc card do the trick and formatted ....fat or fat 16.. do some search goooooooooooooooogle..
Click to expand...
Click to collapse
Non SDHC. Formatted to FAT32 as a post in the forums said. I've tried Sandisk and transcend since someone mentioned transcend has issues.
It can read the card from the OS, but it doesn't leave the bootloader.

TREO 750 "beta testing expired"

Hi, this is my first post on this forum and i'm hoping to get some help to solve my problem.
I have an unlocked ATT treo 750 that i'm currently using with T-Mobile. I was happily running windows 5 and decided to try this new windows mobile 6.5 so i downloaded the rom from a thread on this forum and i ran the update process while my phone was connected to windows zync porgram, so it worked fine, but as soon as i rebooted my phone to the new windows 6.5 it gave me the
"This concludes de beta test of this software release...." now i try to reconnect my phone to my pc to zync and flash another rom but i won't recognize the connection.
what can i do, i know there is a way to flash a rom using your mini sd card but i'm not sure about this process....tell me if i have it right:
1. format your mini sd card using fat32, using a computer with a card reader (i can't format it using my phone cause of ovious reasons)
2. copy the rom image to the mini sd card on the root folder. the rom image should be in .nbh format. (i have a rom called CHEEIMG.nbh by Navenedrob)
3. re-insert the mini sd cad to the phone.....I DONT KNOW WHAT DO AFTER THIS, and what do you mean by HARD SPL or SPL... is it a file i should copy along with the CHEEIMG.nbh file in the mini sd card????
PLEASE HELP ME.. what buttons do i press on my treo 750 to trigger installation...?????
thanks

Hello there if you look a couple of threads down on main form page there's a post by Navenedrob who gives step by step instructions on how to sucessful complete the whole process
I did it about 2 weeks ago as a newbie and it very easy to follow very good update

Also make sure you download and use his WM6.5 ROM. No expiration date ...

hlopez said:
Hi, this is my first post on this forum and i'm hoping to get some help to solve my problem.
I have an unlocked ATT treo 750 that i'm currently using with T-Mobile. I was happily running windows 5 and decided to try this new windows mobile 6.5 so i downloaded the rom from a thread on this forum and i ran the update process while my phone was connected to windows zync porgram, so it worked fine, but as soon as i rebooted my phone to the new windows 6.5 it gave me the
"This concludes de beta test of this software release...." now i try to reconnect my phone to my pc to zync and flash another rom but i won't recognize the connection.
what can i do, i know there is a way to flash a rom using your mini sd card but i'm not sure about this process....tell me if i have it right:
1. format your mini sd card using fat32, using a computer with a card reader (i can't format it using my phone cause of ovious reasons)
2. copy the rom image to the mini sd card on the root folder. the rom image should be in .nbh format. (i have a rom called CHEEIMG.nbh by Navenedrob)
3. re-insert the mini sd cad to the phone.....I DONT KNOW WHAT DO AFTER THIS, and what do you mean by HARD SPL or SPL... is it a file i should copy along with the CHEEIMG.nbh file in the mini sd card????
PLEASE HELP ME.. what buttons do i press on my treo 750 to trigger installation...?????
thanks
Click to expand...
Click to collapse
Hi,
I'm sorry, I wrote that tutorial for people who couldn't use HARD SPL (A piece of software that lets you flash the phone) to get Windows Mobile 6.5.
Try formatting the memory card to FAT32 using a card reader, then from your computer, download the ROM here and paste it onto your memory card (ROM Link- http://forum.xda-developers.com/showthread.php?t=541417 ).
Load the memory card into the phone.
Where you've just loaded the memory card, there is a Reset button. It's tiny, and its located where the memory card slot is.
On the other side of the phone is the Media Button. It's the one below the volume buttons. Hold this button down and press the Reset key with your stylus.
The screen should load into the "Bootloader" mode and try to scan your memory card. If it recognises the CHEEIMG.NBH file, it will ask you to press the Call End key and then go on installing itself (I hope).
After saying all this, please note that I'm not an expert and had to experiment. I didn't however brick my phone with a Beta release so I'm giving you this in the hopes that it will work.
Just make sure you have the CHEEIMG.NBH file. It may have a different filename (anything that comes before .nbh), you just have to rename it.
Secondly make sure your card is formatted to FAT32. Google it if you don't understand or if you don't know how. I use a mac so formatting is easy.
Thirdly, familiarize yourself with starting up in Bootloader mode.
Have a play, I hope this helps.
eD

Help!!!!! Flash topaz problem!!!

Hello. I have two TOPAZ devices, which both have been flashed with a custom ROM. I flashed them around 2-3 months ago. When i tried to turn one back to WM 6.5 Original, it got bricked. So :
1. Can a TOPAZ be restored to the original factory state?
1.1 If yes, how?
2. Is there anyway to unbrick a TOPAZ?
3. Should this be 4?
Excuse my english
Thanks,
Mike

Bricked??? Lets see... To flash the original ROM, do the following:
1. Extract the original downloaded ROM-file (should be an self-extracting .exe file).
2. Copy the extracted .nbh-file to the root of your sdcard and name it: TOPAIMG.nbh.
3. PowerOn phone holding the VOL-DOWN key pressed until Rainbowcolorscreen apears.
4. Press Power to start internal flashing.
5. After flashing, Softreset...
Thats it... if one of these steps fail, please describe exactly what is happening.
Greetz DN

WOW man!! That WAS a fast reply, thanks. I am at work right now, so I can't do much although, how do I extract the rom?

"2] Format your SD card into FAT32:
- go into dos and type:
format <volume> /FS:FAT32 /A:4096
3] Run Qmat to create a gold card:
- Put the formatted microSD card in the working WM device and connect via ActiveSync
- Run Qmat, Go to Hardware Forensics and select 'Generate HTC Goldcard'
- Select your bricked device's key
- Get the SD Card Serial from WINCE Device
- Save the Goldcard image to the SD Card
Now you have a SuperCID which allows you to flash any shipped ROM"
*thats from the sticky under unlocking/flashing*

Scabes24 said:
"2] Format your SD card into FAT32:
- go into dos and type:
format <volume> /FS:FAT32 /A:4096
3] Run Qmat to create a gold card:
- Put the formatted microSD card in the working WM device and connect via ActiveSync
- Run Qmat, Go to Hardware Forensics and select 'Generate HTC Goldcard'
- Select your bricked device's key
- Get the SD Card Serial from WINCE Device
- Save the Goldcard image to the SD Card
Now you have a SuperCID which allows you to flash any shipped ROM"
*thats from the sticky under unlocking/flashing*
Click to expand...
Click to collapse
thanks for the quick responce. so let me get this straight,
: i format my MicroSD
I connect it to my PC and with Qmat I Generate an HTC Goldcard
*didnt get this part* my bricked device's key? how do I do that?
then I use WINCE to get my serial(sdcard)
and now save the goldcard image to sd.
Is this correct?? thanks
Now, after i follow these steps, how do I flash the rom? same way as usual, or is it a special method?
and last, this is for unbricking?
Thanks again.
btw will the method in post 2 work for a fullyworking custom ROM device?

It seems like its basically just allowing you to connect your phone - enter bootloader - and run the .exe (TopazRUU) from your computer to flash a stock rom.
you should read the post in the first sticky, then look at "unlocking/flashing" and you will see #5 Unbricking

thanks

Is your problem solved?

yes, it is!! thanks everyone

Problem Solved - Closed Thread

[Q] problem with htc bree100

when i started update i cant sow old version of my rom i have in program for upload new rom version but no old version and i have always error messages after that
thanks for any help and sorry for bad english

1. SD card (maximum 512Mb) format in FAT32
2. Unrar RomUpdate package
3. File xxxxxxxxxxxxxxxx.nbh rename to BREEIMG.nbh
4. BREEIMG.hbh transfer to SD card
5. Power on phone and let hem connect on ActiveSync
6. With free version of PSAS make a GoldCard for Breeze and save on Win SD
7. Power off the phone
8. Press Camera +PowerOn , phone come to bootloader mode and just follow instruction on screen
psas.revskills.de/?q=node/6

boot menu

Hello!
I am trying to flash my x1 with custom ROM.I do like i must i copy kovsimg.nbh file to storage card and than i turn off mobile phone and than i go to boot menu but there said no file found so i cant flash my mobile phone. I did HARDspl-it so i dunno whats the problem. Any solutions?
thank you

how to flash you rom
meebica said:
Hello!
I am trying to flash my x1 with custom ROM.I do like i must i copy kovsimg.nbh file to storage card and than i turn off mobile phone and than i go to boot menu but there said no file found so i cant flash my mobile phone. I did HARDspl-it so i dunno whats the problem. Any solutions?
thank you
Click to expand...
Click to collapse
You must put the file in the root of the storage card not in the folder..
and did u already tasks 29 your device..??
i suggest u use the 826x rom and use spl 0.78, because its most stable and has a good batery life...
this was the link that u can download the Rom.. http://www.826x.blogspot.com/

I open storage card and put that .nbh file in it and not in any file inside storage card.I didnt task29 before HARDspl.

and you can see the file in your file manager?
sometimes I experienced something like that and couldn't find the file on my sd, strange but true, I had to recopy and then it worked

meebica said:
I open storage card and put that .nbh file in it and not in any file inside storage card.I didnt task29 before HARDspl.
Click to expand...
Click to collapse
rename the .nbh file to "kovsimg.nbh" place to sd card root.. turn off your phone.. then holdown the volume down key.. press the power botton together.. it will be a bootloader screean.. and notify u to upgrade...