Database Develop

Problems with ActiveSync and wm 6

Everything works fine.
But i cant use activesync 4.5 to sync my contacts and so on
(i can install programes but it doesnt sync the conntacts.)
If i disable advanced network functionality the xda freezes
and the computer shows an unknwon usb device.
Can someone help me ?
Sorry for being a noob.

Everything is fine for me, are you sure that you flash the rom correctly as ordered ?

Sync problem
often can`t detect pda synchronitation . it`s show sync problem . Any way to fix it ?

I told you I don't have any problem which mentioned may be you have to reflash your rom, and start from the beginning.
Or first, you can delete your pairing connection with the pc, reinstall your active sync. And try to pair again. If you said "often", I hope this is not because of your hardware problem.

make sure your device is powered on ( the back light is on)..i also get it some time (only if i shut it by pressing Power Button at top)

Himalaya's USB Port is allergic to hubs
Don't try to use an USB Hub to connect the Himalaya to your PC. Always use a direct connection. This solved the problem for me.

...
Hi,
urbstar said:
Everything works fine.
But i cant use activesync 4.5 to sync my contacts and so on
(i can install programes but it doesnt sync the conntacts.)
If i disable advanced network functionality the xda freezes
and the computer shows an unknwon usb device.
Can someone help me ?
Sorry for being a noob.
Click to expand...
Click to collapse
Got exactly the same problem, since upgraded to WM6 (Tofclock Fresh ROM) Activesync never finds the PDA. Tried really everything possible, doesn't work. But 'cause there are some beautiful tools like WM5Storage or PIMBackup I don't care about ActiveSync.
May be its - as mentioned here - the USB Connection over USB Hub. But it's an internal one in my case so I can't proof.
And I don't think that the workaround for this problem is a ROM-ReFlash 'cause everything else works fine.
So long
HonkBB

i have same sync problem
i have upgraded from wm2003se to WM2006 AKU7.0 RAMDisk-40MB Pagepool size-24MB for Himalaya and everything is good but no activesync.
i have reflashed 4 times now and still no good.
any ideas???

newquaymarc said:
i have upgraded from wm2003se to WM2006 AKU7.0 RAMDisk-40MB Pagepool size-24MB for Himalaya and everything is good but no activesync.
Click to expand...
Click to collapse
Is your USB cable connected to a hub? This was the problem in my case (see above), but other users reported that it fails to when directly connected. Strange problem this is...

stupiddog said:
Is your USB cable connected to a hub? This was the problem in my case (see above), but other users reported that it fails to when directly connected. Strange problem this is...
Click to expand...
Click to collapse
cheer for reply but no cradle connected direct to my laptop
gonna have to go back to 2003 se till i hear of solution
shame xda runs great with wm6

I just want to ask you about active sync which version did you use ?

selangkahlagi said:
I just want to ask you about active sync which version did you use ?
Click to expand...
Click to collapse
thanks for replying
im using active sync 4.5 with xp pro all has been ok till this upgrade

I have the same with you, and everything is going well. May be you can try to delete the pairing both form your PDA and your PC and try to make new pairing again Good luck

selangkahlagi said:
I have the same with you, and everything is going well. May be you can try to delete the pairing both form your PDA and your PC and try to make new pairing again Good luck
Click to expand...
Click to collapse
cheers yes tried that.
im not happy with install anyway so will try again in a few days,
i think the unlock/unhide, doc tool did'nt work as i only got a formating msg
and still had my old splash screen and 14 odd me after the upgrade.
many thanks for your help.
will let ya know how i get on

newquaymarc said:
cheers yes tried that.
im not happy with install anyway so will try again in a few days,
i think the unlock/unhide, doc tool did'nt work as i only got a formating msg
and still had my old splash screen and 14 odd me after the upgrade.
many thanks for your help.
will let ya know how i get on
Click to expand...
Click to collapse
If you had old splash screen, big possibility you didn't do the last step

selangkahlagi said:
If you had old splash screen, big possibility you didn't do the last step
Click to expand...
Click to collapse
i did do it but dont think it ran correct, is it ment to run on 2003 se?

newquaymarc said:
i did do it but dont think it ran correct, is it ment to run on 2003 se?
Click to expand...
Click to collapse
did you do this step
hardreset your device.
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad and wait until OS starts.

hi
yep done all that, NO-YES-YES i think the prep work before upgrade did'nt work..
maybe i need to goto wm5 then wm6, but wm5 was too slow for me to use.

a lot of laptops actually have one set of usb ports that are registered as a powered hub and often these don't really have enough power across all the ports... jst an idea...

active-sink!!!!!!!
hi all xperts,
lemme start with my Thanx to Tof the great and Helmi who have made this possible for the good ol' Hima..
Now i need some help -
I installed this package close to a month back with all instructions point by point.
Activesync was the problem..
Today i thot i'll increase the storage space - ran the unlock and then realised the Hima Doc tool is a exe file and i'll hv to have a valid activesync connection before i can get that worked.
Then i thot, i'll reload WM6.0
Again, started in Boot loader - Got the Serial Screen with v1.06 in bottom, connected my device to run the software -
I'm redoing the flash now - wish me luck guyz!!!!!!!!!!

Ba Upgrade Via Sd Card Or Bluetooth

My Blue Angel Activsyn Is Not Recognized By The Pc For A Reason I Do Not Know , Tried Many Times Hard Reset Soft Reset , Mtty Tool
Bootloader Mode Nothing Is Working If Any One Has An Idea How Can I Upgrade Or Even Re Falsh The Same Rom I Will Appreciate It Thanks

mohannad18 said:
My Blue Angel Activsyn Is Not Recognized By The Pc For A Reason I Do Not Know , Tried Many Times Hard Reset Soft Reset , Mtty Tool
Bootloader Mode Nothing Is Working If Any One Has An Idea How Can I Upgrade Or Even Re Falsh The Same Rom I Will Appreciate It Thanks
Click to expand...
Click to collapse
You MUST flash via sync, there is no method available to flash from SD card. Are you using XP or Vista? There is a known issue with Vista not liking the BA. Are you manually putting the BA into bootloader mode then placing in the cradle or trying to do it some other way? The method that works 100% for me is to manually put in bootloader mode (power+reset+record), this gives me a screen that says Serial at the top and a version number at the bottom, there is no backlight and when I then place it into the cradle Serial changes to USB. At this point on the computer run MA_Upgrade and everything should work. Keep in mind that I will never use Vista so if you are the YMMV.

will i could manually go to bootloader mode but the time i place device on cradle " unknown device" appears and running the maupgrade.exe leads to blank upgrade rom version several times i have done it ??? any suggestions
i have windows xp , activsyn 4.5 , bootloader ver 2.06

mohannad18 said:
will i could manually go to bootloader mode but the time i place device on cradle " unknown device" appears and running the maupgrade.exe leads to blank upgrade rom version several times i have done it ??? any suggestions
i have windows xp , activsyn 4.5 , bootloader ver 2.06
Click to expand...
Click to collapse
As silly as this sounds, try a different USB port. Also make sure you are directly connected to the computer not via a USB hub.

tried more than one computer for connection and more than 4 ports still i got the same " usb device not recognized"

mohannad18 said:
tried more than one computer for connection and more than 4 ports still i got the same " usb device not recognized"
Click to expand...
Click to collapse
Try a different cradle/cable.
The time I had this exact problem, it turned out of be a broken wire in the data cable.

i bought another cradle still i hvae the same message " usb device is not recognised"

Hrmm... I'm going to throw out a few ideas to look at. Some probably don't apply since you tried this on another machine, per your post, but it can't hurt in regards to this issue...
Try uninstalling activesync, reboot, reinstall, reboot. The 'drivers' that are used are installed with activesync.
If you have any 3rd party USB drivers, try reinstalling them.
Disable 'advanced network functionality' on the phone
Backup your phone and hard reset
Do you have anything that monitors the USB port on the machine you are trying to do this on?

Make sure you are using activsync 4.5 or newer. Other than that and what you already read here I can think of nothing.

i have tried so many versions of activesyn 3.x-4.5 with reboot each time of installation ,advanced network diabled, still the same thing " usb device not recognized"
sorry for inconvenience what is usb moniter machine??

BA - Does the activesync (3x-4.5) - work via bluetooth 4 U/G's ?
Angel - Does the activesync's (3x-4.5) - work via bluetooth 4 U/G's?
(no cradle / no usb) , but file transfere's work ok, via BT exchange folder (paired)
for running the ====#====#===#XDATools#==#=== & the #====#====#====#special_rom_1.2.exe#==#
angel of the ph20b
1.31.00 wwe
rom 12/13/04
1.06.00FM
1337.38,
ext rom 1.31.139wwe - flavours
my BlueTooth is belkin F8T008 (belkin say it uses comm4) - (BlueAngel say it uses - in comm5 / out comm 6), & activesync4.5 says (no-way, even adding ports, then removing all under comm9 etc)
(if I could run them from midlet, from sd say )
ASK B4 U TRY ??? (101/Flash4dummies/NewbiesTube . . . .YouNube? where ()not the wiki() - Im getting to be a silver surfer, already!
followed a few tutorials, none look like my sp3, on xp-pro, I also have no outlook, etc (no excel, - NO office!), but I only came for a soft-key fix/addon = 4midlet's)
tried removing the pair'ings from regedit(then regclean). Oh and when running activesync from BA, I cannot even get a PC (discoverable 'n all devices 'n all services ect
and breathe!
Oh and any reply's would be gratefully received, B4 '2010', that is -
shame the bolt that was shot, was just too soon, so no score for the aim, though! -

usb activesync problem
usb activesync problem
ignore the previous post - cannot connect to activesync via bluetooth!
radio upgrade worked !!!!!!!!!!!!!!!!!!!!!!!!!!!
special_rom_1.2.exe, unzipped to a xdatools folder
running start.bat, after activesync's finnished sync-ing
in the dos window I get a get device error
and
error 011:execute remote comms prog error

I'm VNese, my level of Eng is poor. but I think u should check your USB port. Do u use full of usb port? may be, the power in USB port is low -> error. Or hardware(USB chip) is bad. check more

Shot in the dark but I had the same problem with a friends 6700. I found out that the antivirus/firewall/internet security suite was blocking the proper ports needed to connect. When I disabled the software for a moment, attempted a sync it would work, then I could turn the software back on and be fine. If I disconnected and reconnected it would only charge. Give that a whirl.

One of the USB Devices attached to this computer has malfunctioned

DESPERATELY NEED HELP.
Every time i connect my wizard to my machine using the USB cable, i get the following message in baloon.
"One of the USB Devices attached to this computer has malfunctioned, and windows does not recognize it."
It appears as "Unknonw Device" on windows device manager.
This started happening when i changed my ROM to AMP.v2.Vanilla. Prior to that my wizard was connecting fine. I have been trying to resolve this for days now but no luck.
Following are the things i have tried.
1. Un-installed Activesync & re-installed.
2. Soft & Hard Reset the device.
3. Tried going in bootloader so that i can install my preivous rom, but the machine still doesnt recognize the device and gives the same message as mentioned above.
4. Removed all the USB controllers and re-installed in the machine.
5. Tried on different machines but same results, so its not machine specific.
6. Tried with a new cable to so its not the cable, it has to be the device.
Anyone who can help with this. I am sure i am not the only one having this trouble.
Any kind of help is appreciated. Just need to connect and go back to my preivous rom.
FYI: I am running WINXP SP2 on my machine.
ROM: 10.0.0.10
Radio: 02.69.11
Protocal: 1.1.13.30
Thanks in advance.
Nick.

You can flash in bootloaders mode,its not necessary to activesync.Get you phone in Bootloaders (tri color screen) by holding down Camers button and either Soft Reset or push Power On button,it'll go into bootloaders,hook up the phone with pc via usb cable,watch small usb appear at the bottom of the bootloaders,its good to go and run the RUU in the Rom,it'll start to flash and upgrade.Solve the activesync problem afterwards.

Thanks for the reply mate but i have already tried that.
I went into the booloader and connected the usb. It does show USB at the screen, however my PC doesnt recognize it and the RUU doesnt run. It says to connect the device.
I am not at all worried abt the activesync. Syncing is the last thing i'll think. I just want to connect and go back to my previous rom.
Any other suggestions.
Please see attached screen shots.

This sounds like a hardware issue on your phone. I doubt this works but go to start -> settings -> connections -> usb-pc and either check or uncheck the box then close that app.
If that doesn't work Search for the thread on flashing from the miniSD card. But again, this sounds like the usb on your phone has failed.

I have tried checking the USB to PC and unchecking it. No help with that.
One more interesting thing is the phone does get charged with the USB cable, just doesnt connect.
Will check the thread for flashing from minisd.
Thanks bunches.

hmm,
Hard reset your phone and uncheck the option 'allow network connections' or something in the phone settings...> connections...> usb to pc
This error occurs when there is an “open port error” before upgrading ,You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again. disable or stop any antivirus/firewall running or any other such program which might be hindering the flash,don't surf the net.
Kill 'WCESCOM' altogether,in the Task Manager,stopping activesync.

nick_shire said:
I have tried checking the USB to PC and unchecking it. No help with that.
One more interesting thing is the phone does get charged with the USB cable, just doesnt connect.
Will check the thread for flashing from minisd.
Thanks bunches.
Click to expand...
Click to collapse
hmmm,you got a connection problem buddy,the mini usb port of the phone is broken or damaged,you cannot flash with sdcard method,untill you already had made a backup of the rom earlier and saved it on the sdcard.
Get the mini usb port of the phone repaired or you can try to wriggle it a bit and check if it works and try to hold it there in that possition till the flash completes.

IS there a place i can get step by step process of flashing through SD card?
For all the forums, i am not able to understand anything./

Even the mtty doesnt work, it doesnt open the usb port.
No Luck as of now.....Am very desperately waiting for any Saviour....PLEASE

No other way out,except to get the freakin mini usb port repaired or replaced.

zabardast_1 said:
hmmm,you got a connection problem buddy,the mini usb port of the phone is broken or damaged,you cannot flash with sdcard method,untill you already had made a backup of the rom earlier and saved it on the sdcard.
Get the mini usb port of the phone repaired or you can try to wriggle it a bit and check if it works and try to hold it there in that possition till the flash completes.
Click to expand...
Click to collapse
Dang, thats right. I forgot that on the Wizard you can only flash a previously saved rom image. Can't just flash roms like you can on the Tilt.
Yep, basically, you have to get the USB port fixed as you are stuck where you are currently at on the Wizard I'm afraid.

Thanks guys. Have given my Wizard to get the Mini USB Port changed. I have my fingers crossed. Hope it works.

What exactly happens to the mini usb port?
I am having the same problem syncing.
The phone hooks up, charges, and makes the "connected" sound when I plug it into the usb port, but NO activesync...DOH!!!

Honestly, i couldn't figure it out.....no one seems to know whats the cause. The phone is bricked. It wont even start now... and its lying....
I am using an LG KS20 these days.....
Let me know if somebody happens to find a solution for that.

nick_shire said:
Honestly, i couldn't figure it out.....no one seems to know whats the cause. The phone is bricked. It wont even start now... and its lying....
I am using an LG KS20 these days.....
Let me know if somebody happens to find a solution for that.
Click to expand...
Click to collapse
Dear NIce_shire,
i am having the same problem and i got it resolved just by holding and tightly pressing the mini usb in my device. Its basically the problem with mini usb port of pda (Hardware) not a software one. Get it reparied from market or do it by urself. Good Luck!

USB link?
Hi mfrazzz
I have the same problem - USB link stopped working after a Radio upgrade. Definitively not a h/w USB miniport problem. Even when I get the Wizard G3 phone into bootloader and the USB word is at the bottom in the white line, flashing ROMs does not work as the RUU reports Error message stating no USB link (BTW, ActiveSync also reports no mobile device present and doesn't connect).
Is this a bricked phone then?
Thanks.
DesperateDan
PS The set is an MDA Vario and I had successfully installed S.V.I.s Manila 4.5 Beta (IPL 1.01, SPL 1.01 shows now, but was IPL 1.01, SPL 1.06 prior to installing Manila and Radio was 1.12.10 and I upgraded it to 2.69.11 and then the bloody thing stopped working and the USB link can't be enabled again)

Dear all,
I was facing the same issue of "USB device malfunctioned" and got it resolved yesterday. Its not because of software neither coz of cable (i did changed lots of cables but faced the same issue), its just because of mini USB in device. Its working perfectly alright now, it may not be replaced even dont need replacement at all. It needs minor soldering, even you can do it by urself. Just open 4 screws at its back (two under the camera cap one is below stylus placement and 4th is on opposite side) and open it. No need to be worried about......
Regards,
Barjees

Can't connect to my pc!

I just want to connect so i can update to the newest swedish rom released.
And of course everything else
When i connect the usb to phone i get the alternatives "Activesync" or "disc-unit" or something like that.
I choose activesync.....it connects but after a few seconds it disconnects.
It will show up on my pc but just disconnects right after....it has always worked before.....i really don't know what to do.
Then i use the other alternative to connect.....it seems stable but it is extremely slow.....one mp3 at 3mb takes about 40minutes to upload to phone.
I have the "Official Update 1.37.401.3" installed but i want install the newer one.
Please help me.
My usb cords i have tried using is flawless....everything works.
Im running Vista Ultimate Retail.
Please help me through this ordeal....I'm almost at the point that I'm going tp buy another phone and leave htc forever
I really want this phone to work. It worked before actually...It might be when I updated with the Official Update 1.37.401.3 or exactly a few days after that my problems appeared.
REALLY NEED YOUR HELP XDA-PEOPLE!

Have you tried connecting it while it's in bootloader mode? If all you want to do is flash the ROM that's the best option.
One question, why did you "upgrade" to the 1.37 ROM? Isn't that what came on the device?

Open active sync (it allready might e open as u tried to connect) and go to menu (on the right) select connections and see if u have use usb connection enabled.

poedgirl said:
Have you tried connecting it while it's in bootloader mode? If all you want to do is flash the ROM that's the best option.
One question, why did you "upgrade" to the 1.37 ROM? Isn't that what came on the device?
Click to expand...
Click to collapse
I don't know what bootloader is...sorry. And there was an older rom on the phone before i upgraded.

hms666 said:
Open active sync (it allready might e open as u tried to connect) and go to menu (on the right) select connections and see if u have use usb connection enabled.
Click to expand...
Click to collapse
Yes it is enabled.

Windows XP uses Active sync V.4.5.0
Windows Vista uses Windows Mobility center:
http://www.microsoft.com/windows/windows-vista/features/mobility-center.aspx
First check your advanced energy-settings (control panel, system)
To make sure put everything on 10 minutes, as these settings will reset as soon as your new (and faster 1.93) rom is installed.
Connect your phone and make sure you select the sync option, not the external disc option. Make a backup.
Then use an unsigned hard-spl if you have firmware 1.37 or higher. (signed won't work) http://forum.xda-developers.com/showthread.php?t=400950
When finished install the rom you like.

I Resolved It!
I managed to flash my phone with the new swedish official rom.
So I can connect now.
Thanx for helping me.
The problem seemed to be in Windows Vista...it wouldn't allow my HTC to keep beeing connected for too long
I resolved the problem on my other computer.
And I love the speed of the new rom by the way ...It gets better and better all the time.
Thanx again XDA Developers.

have same problem
hey
How did you resolve this in windows vista i'm having the same problem with
windows vista ultimate
Please share
THKS

Chino68 said:
hey
How did you resolve this in windows vista i'm having the same problem with
windows vista ultimate
Please share
THKS
Click to expand...
Click to collapse
I used my other computer (Win XP) to flash my htc diamond with the newest swedish rom...and now it will even work connecting to my vista computer.
Good luck with your phone

No ActiveSync connection, but still charging??

Hello,
i have a big problem and i dont know how to solve it.
1) I flashed the OliNex 1.56 using the HSPL method.
2) Flashed Xnor 1.4 Rom
3) Flashed LIA 14.5 Rom
4) Flashed a stock Rom(O2 6.1 Radio 1.12)
5) Flashed back to LIA 14.5(Installed Radio 1.14 and Rillphone 1.14)
6) Want to flash to L3.5, but no connection any more and stll charging over the usb cable
7) Hard reset, nothing changed
Yesterday the connection to activesync was available, but today the phone still charging but the connection to active sync is lost.
I set the phone to bootloader to flash a other rom, but the phone does not detect the usb connection (no usb at the bottom).
Hope you know what to do...
Thx

Try to reset/reboot your pc. I have the same problem from time to time. I'm using Vista and WMDC.

ClydeB1 said:
Try to reset/reboot your pc. I have the same problem from time to time. I'm using Vista and WMDC.
Click to expand...
Click to collapse
I also reseted/rebooted the pc (on the work) nothing happens.(winxp)
Now i am at home and it works with win7???
I dont understand that.
Thanks for advice
Greetz
/can close

PaschaD said:
I also reseted/rebooted the pc (on the work) nothing happens.(winxp)
Now i am at home and it works with win7???
I dont understand that.
Thanks for advice
Greetz
/can close
Click to expand...
Click to collapse
Remove and reinstall activesync on your xp pc. You can also try to remove all known devices in AS first.

kwbr said:
Remove and reinstall activesync on your xp pc. You can also try to remove all known devices in AS first.
Click to expand...
Click to collapse
Also tried, still the same...