Hi there
I've not had this problem before
I had to reset my Kaiser because it froze while trying to do too many thingsd at once.
And it rebooted to the pin screen, I put my pin in and waited, and waited, and yet nothing.
I've had the pin lockout bug before and its not that, none of the top bar information is displayed, in fact the only thing showing is my signal bar with a little X next to it.
i managed to boot into safe mode with pocket plus with no worries, but with any standard soft reset I can get past the pin screen.
So I took the plunge and Hard reset expaecting to have this fixed. But im still stuck at pin screen, with no siganl showing.
Anyone any idea what the bloody hells going on?
Im on Dutty's latest dual rom. but i dont think its to blame...
help...cheers in advance
Related
I've search woth Google, GWENI and Wiki and could not find a similar case. Please let me know if this has already been dealt with.
So, everything was working fine earlier this morning (alarm, calls, wifi, bluetooth A2DP), I have not installed nor tweaked anything in weeks - I finally had the phone setup the way I wanted to...
This morning I was adding an event in my Calendar, and I got an "Application Error" msg - which would not allow me to add the event. I quit calendar, tried again and the same thing happned. I had just succcessfuly added a Contact a second earlier so I decided to Soft Reset (Using the button on the bottom and stylus) and when it started booting up I noticed the AT&T 3G Splash Animation Screen (which I had disabled back in February - this is were I went "Oh no ") followed by the Windows Mobile Splash screen with "Tap the screen to set up your Windows Mobile based device". So I'm guessing the phone had a Factory Reset for some reason.
Unfortunetly, my struggle doesn't end with me losing my information. The phone is stuck at that Windows Mobile Splash Screen. I removed my SIM Card (which is not ATT), and battery for a few minutes but I have only been able to pass the Spash Screen about three times and the phone gets stuck on the Screen Calibration/Alignment set up. Other than the Reset Button, none of the buttons respond at this point, including the power button.
Any suggestions?
Any help will be GREATLY appreciated =)
Jimmyy said:
I've search woth Google, GWENI and Wiki and could not find a similar case. Please let me know if this has already been dealt with.
So, everything was working fine earlier this morning (alarm, calls, wifi, bluetooth A2DP), I have not installed nor tweaked anything in weeks - I finally had the phone setup the way I wanted to...
This morning I was adding an event in my Calendar, and I got an "Application Error" msg - which would not allow me to add the event. I quit calendar, tried again and the same thing happned. I had just succcessfuly added a Contact a second earlier so I decided to Soft Reset (Using the button on the bottom and stylus) and when it started booting up I noticed the AT&T 3G Splash Animation Screen (which I had disabled back in February - this is were I went "Oh no ") followed by the Windows Mobile Splash screen with "Tap the screen to set up your Windows Mobile based device". So I'm guessing the phone had a Factory Reset for some reason.
Unfortunetly, my struggle doesn't end with me losing my information. The phone is stuck at that Windows Mobile Splash Screen. I removed my SIM Card (which is not ATT), and battery for a few minutes but I have only been able to pass the Spash Screen about three times and the phone gets stuck on the Screen Calibration/Alignment set up. Other than the Reset Button, none of the buttons respond at this point, including the power button.
Any suggestions?
Any help will be GREATLY appreciated =)
Click to expand...
Click to collapse
I understand the buttons are not responding. However, a similar situation happened to me last week. I just had to do a hard reset (the buttons only responded when i did a hard reset).
hold down both soft keys while inserting your stylus. Hopefully this works.
also try flashing a different rom and see if that solves the problem
Yesterday I took my battery out of my phone to remove the dust from inside the phone. When i replaced the battery back into the phone, it booted up into the tri-color screen and has been there ever since. I haven't modified the phone since receiving it from AT&T at all. When i actually noticed the problem I tried to reset the phone through the hole on the bottom of the phone. At first, it booted up normally but was out of batteries since it had been running on a bright screen for a couple of hours. Thus it turned off immediately. I have tried to reset it again but it seems to do nothing. Since then when I put the battery back in and I turn the phone on it returns to the tri-colored screen and it says SERIAL in the bottom white area. When plugged into my computer it says USB in the white area. On the top of the tri colored screen, in the red area, it says:
KAIS1*0
SPL-1.56.0000
CPLD-8
I thought about downloading the newest ROM update from HTC but my phone wont sync with my computer, and the tutorial says it needs to in order to install properly. If anyone could help, please let me know!
Update!
I put the battery back into the phone and it booted up just fine....it was a little slow and worked normally for a couple of minutes. Soon it started to act up. When i plugged the phone into my computer it automatically started to freeze, when i unplugged it from the computer it would work just fine! I then turned my phone off again and now it is back to the tri-color screen again!
try hard-resetting the phone.
To do this, hold down the two soft keys at the front while pushing the stylus into the reset hole. Just make sure to back up any data you want, as it will delete it all (files, contacts, etc.)
Tried a Hard Reset
When I finished it, it just went back to that tri-colored screen. Now the phone will turn on every 10th time i try and work for a couple of minutes. When the screen turns off it wont turn back on when i push the power button. The green light still blinks though.
I have been having this exact same problem for a little while now, any help would be more than appreciated.
EDIT: Everything about the phone was AT&T stock ROM from Oct. '07.
i think it replacement time
hi all once again.i was using my kaiser yesterday then my phone went into tri screen.tried hard reset soft reset.phone reboots in tri screen.im using Duttys Official WM6.1 Rom 5.2.19716 UC.
ihave kais130 mfg /spl 1-0.0lipof /cpld-8 on screen.
if there is a solution to this i would appreciate help in resolving.thanks in advance
Another sad update!
Well as of this second my phone works okay...slower than usual....but in an hour or so the screen will turn off and the phone will stop working, i will take the battery out.....wait about 45 minutes and hope that it boots up normally. No one has any idea why this is happening to multiple people? I have had this phone for maybe 3-4 months. Is the failure rate that broad and fast on these phones???
WTF
This phone is ridiculous. Now if I keep the phone plugged into my computer so the screen wont time off, the phone works just as normal. The moment I unplug the phone from charging it decides to die on me after an hour or so!
this happened to me last nite.
spent hours and hours trying to fix.
ended up reflashing orig att rom..
everything is fine..
proceeded on to a cooked rom and all is well..
added some apps ..
so far -- awesome
Good News!
Magically my phone started syncing with my computer randomly. Thus it allowed me to flash the rom with the original ATT rom and so far my phone is back to normal working great!
tri screen sorted
i bought my kaiser off ebay..i couldnt sort tri screen.i had various roms on at various times .i had no warranty. on pay as you go.decided to take to local o2 shop.got it back today fully working for free.took them 8 days.
Hey, did you have any luck fixing this problem - I've been looking mad for a solution to my tri-screen problem, but no joy...
KAISI*0
SPL-1.93.0000
CPLD-8
appears on my screen.... I don't now how to fix this puppy and it's only a couple of months old...
I started plugging the charger in and soft reset and it would work until i could find a new OS for it, Rom or RUU I think, I am not sure if it works, but now I can't get it off Tri-Screen to run it..
Any help anyone please?
You better take a look here for a solution : http://forum.xda-developers.com/showthread.php?t=423486
jezzaflyboy said:
Hey, did you have any luck fixing this problem - I've been looking mad for a solution to my tri-screen problem, but no joy...
KAISI*0
SPL-1.93.0000
CPLD-8
appears on my screen.... I don't now how to fix this puppy and it's only a couple of months old...
I started plugging the charger in and soft reset and it would work until i could find a new OS for it, Rom or RUU I think, I am not sure if it works, but now I can't get it off Tri-Screen to run it..
Any help anyone please?
Click to expand...
Click to collapse
I'm used to enter my SIM PIN before the Today screen is displayed. So the X1 connects to the mobile network before you start working with the phone.
But now the X1 starts WM and i have to click manually on the phone settings to enter the PIN. SIM Pin is turned on.
Is there any way to get a "auto SIM PIN screen" on startup?
Actually i forgot to note that i get a PIN Screen on Startup. But just for a few seconds and you cannot type in any number. It then fades and the today screen is displayed. I think there's something going wrong. mh.
Thanks for your advise!
I was wondering the exact same thing. The thing displays for a second then goes into loading today screen leaving you manually starting the SIM PIN screen.
This is a sideeffect of xperiaTweak, it's been discussed here already. A simple search could have given you the answer.
There is no fix for this right now but it should not matter -either you can simply press the green phone-button, then you can type in your PIN, or you just deactivate the PIN-code.
its not xperia tweak,, because the moment i got this phone, i am grumbling about this already... i think its PANELS
I have the same problem exept i used to be able to enter my pincode but now i only get the first 2 numbers then it just "logs on" by itself... i don't think its TweakXperia either coz it worked before and i hade it than to...and when i check the conn manager it says the phone is on, not i flight mode or anything else... so weird!
leobox1 said:
its not xperia tweak,, because the moment i got this phone, i am grumbling about this already... i think its PANELS
Click to expand...
Click to collapse
Could be too. This behavior started the moment I installed XperiaTweak so I thought this program is the one to blame.
Maybe it's just to wait for the firmware update. And after all, how often do you softreset your phone? I installed all the programs I need and now it's weeks before I restart the device.
Actually I've installed xperia tweak, but I did not use it. Changed some chache sizes with advanced config.
I think it happened the first time after i allowed Sprite Backup to automatically enter the SIM PIN. But turned that feature off and the programm is not on auto start ... as far as I know.
Ah and I searched the forums and found nothing about sim und pin .
I "soft reset" my phone on most evenings by pressing the On key and selecting to turn the device off. There's no need for the phone to be on standby when I'm sleeping.
I think I'll do a hard reset and take a look when my SIM PIN Menue is disappearing.
I simply removed simlock. I rarely turn the phone off, so there is little chance it would work.
Well there's the difference!
I turn it off more often. Btw, Soft Resets once a day are recommended by SE on their X1 site. To "clean up memory" . hehe
And its quite nasty to go to the PIN menu manually all the time.
I usually just press the call button and the phone brings up the PIN menu. This is quite an easy way I think...you don't have to navigate too much this way.
Dadaism said:
Well there's the difference!
I turn it off more often. Btw, Soft Resets once a day are recommended by SE on their X1 site. To "clean up memory" . hehe
And its quite nasty to go to the PIN menu manually all the time.
Click to expand...
Click to collapse
Tell that to my Nokia 1208 I still have somewhere. 7 weeks of battery lifetime and no "memory cleaning"
On topic: WHen the PIN code screen shows up, just type it in and press ok without waiting for a response. On my X1 it usually works, the screen hangs but the PIN gets entered.
Pressing the call button is faster, but still manually.
I did a hard reset on my device and payed some attention to the SIM PIN screen.
After the reset, with no external programms installed (original stock rom) the PIN screen appeared every time, soft reset and complete shut down.
But after I installed the first programms (in this case advanced config and advanced task manager) the SIM PIN screen started to fade away. Surprisingly it seems to be random now. Sometimes the screen fades and the today screen is shown, and on the other side the pin screen stays up until I entered the SIM PIN.
As for today:
Turned mobile phone off over the night.
First start today: SIM PIN screen stayed up.
Soft reset: SIM PIN screen stayed up to.
Yesterday the SIM PIN screen faded away for every Soft reset i made. I've installed a bunch of programms (My_flash, Youtube App, Skyfire, ...).
Until now I have NOT installed Xperia Tweaks! I'll see if the randomness fades with that installed.
Perhaps this occurs, when a programm running in the background causes the (phone) PIN screen to minimize. Sometime it went away when F-Secure wants to update definitions.
No XperiaTweak installed yet and still no SIM PIN screen fade away pattern .
Maybe XperiaTweak also runs in the background on startup, panel switcher or what ever. You could take a look at this .
i noticed that if i start entering the code immediatly after it appears , it is enough time to enter it(6 char) and press enter.Anyway i don't mind pressing the green key once in order to enter PIN
Bump out of curiosity. Is there a solution for this?
hi there,
this morning, without any interactiom, i heard the vibration of my touch diamond restarting.(with original newest ROM from htc website that ran without any problem for several months). battery was about 80% yesterday evening.
but it wasn´t starting at all. after the HTC animation and the green windows mobile screen, it started again. after restarting for 20 minutes i took out the battery, put it in again and performed a hard reset as stated in the manual.
now, on the "rainbow" screen i get a message like
psoc diam stage_pvt 0x32
then i did the Volume-Up reset, and now i don´t even get the red version information in the lower right screen. as it doesn´t even start i cannot get an active sync connection.
any ideas? is my phone broken? i didn´t do anything special, and i wonder why it rebooted without interaction this morning.
any ideas what i can do?
thanks in advance,
jkersch
Mine started doing this about 2 weeks ago it woke me up in the middle of night while sleeping with its vibrator and start sound.
The only thing I have found is that my little reset button at the pen holder dosent work anymore. To do a hard reset i have to takeout the battery and then put it in, hold the volume key and enter key then power it to get it. Flashed by holding volume down and the power on, it hold for about 10min just enough to get the flash.
I managed to flash it once but it dosent help, it constantly reset at the thouch diamond screen. Some times i get to the green windows mobile screen.
As warrenty is out on my phone and ive given up and using another phone.
Same problem in a different thread
Have a look at http://forum.xda-developers.com/showthread.php?p=5279740.
install a new radio worked for me
Hi all!
I got my p9+ less than a year a go, two weeks ago I decided to root the phone, for few days it worked fine and I was really happy with it.
A week ago, randomly, I installed an app, I made a reboot and after that I typed the sim pin and the phone pin, in few seconds the nav bar completely disappered, after that also the stat bar disappeared (it seemed like a strange fullscreen mode), than the launcher wallpaper changed to the stock one and in less than one sec the screen turned black.
After that I managed to stand that the phone was still on, infact if I press the power button the screen shows the two "Shout Down" and "Reboot" buttons.
I've been trying a factory reset but nothing happened, i finished the configuration of the phone but after 10 seconds I had the same problem :silly:
I also tried to get off the sim card, and for few minutes it was working, but than I had the same problem; I'm sure that the problem is not the sim because it asks me for the pin and it actually works in another phone.
Hope someone has a solution, have a nice day