Database Develop

I Can't Upgrade my device

Heloo every one ... i'm tired from this pda p3600 ... since 4 day's i wanna to upgrade my rom from wm5 to 6 & the upgrade process didn't work ... i try everything .... but non is work ...
first i was trying to make upgrade through windows vista home premium but didn't go well & this is the photo for my problem :
http://www.freewebtown.com/Haitham/CIMG0511.JPG
http://www.freewebtown.com/Haitham/CIMG0512.JPG
http://www.freewebtown.com/Haitham/CIMG0513.JPG
http://www.freewebtown.com/Haitham/CIMG0514.JPG
http://www.freewebtown.com/Haitham/CIMG0516.JPG
then i try to upgrade through my freind windows xp ... and also didn't work good .. the error message say that the phone is unable to upgrade do u rom flash or something like that ... so i try to instal the unlock & also same message ....
i'm in **** mood ...
any one can help me please

Until the new version of WMDC is released with fixes, I suggest you use XP computer to do upgrade.
New WMDC v.6.1 coming soon: http://windowsvistablog.com/blogs/w...ows-mobile-device-center-6-1-coming-soon.aspx
The XP computer needs to have Active Sync 4.5 installed. Reboot xp computer before starting, to clear any existing syncs. Delete current sync profile on Trin. Connect to pc via usb as usual, let ASync run, but cancel when it tries any profile, you are left as: Guest sync
You should be connected now. Upgrade rom file should be extracted in explorer, e.g., so you can see all files. Run RUU wrapper or ROMUpgrade exe, depending on rom you're using.
If you go through process, & get error message. Don't disconnect Trinity. Close that page & start again. It should work the 2nd time. When it's working, you will see the boot screen, color bars & at bottom usb notation. (If it says serial, you'll have to, unhook usb connection, reboot computer, re-sync to guest status, & start again.) Then the update screen on Trin will show % bar, if process is working correctly.
If you still get error message, then check Trinity Wiki info as rom upgrade problem FAQ is there. I'll assume your Trin is unlocked. Check boot screen on Trin to see boot loader info. Wiki explains how.
Also: Use SSPL software Bootloader solution from "Des" - this loader ignores the CID and the upgrade will work also with wrong CID. See also http://forum.xda-developers.com/showthread.php?t=293632
If you still have problem, come back here & give info:
1. What rom is currently on Trin? What radio?
2. Did you buy an unlocked Trin? Exactly, what device do you have?
3. What wm6 rom do you want to upgrade to?

Trying to upgrade - i-mate PDA2k DEAD !!!

I try to upgrade my i-mate PDA2K (italian) with Helmi Windows Mobile 6 Profesional R0 ...
The program started, recognize my PDA:
Your device software is about to be update from :
Device CE image version : 1.12.24
Device Extended image version : 1.12.168
Device Radio image version : 1.02.00
To :
CE image version : 5.60.00
Extended image version :
Radio image version :
While the update is in progress, your device will act as though it
is outside of network coverage. So, all your calls will be diverted
to your Answer Phone, and any messages will be delivered
once the update is completed.
Please click Update to continue.
Click to expand...
Click to collapse
After then, remain stucked on:
Checking the information on your device ... Please wait ...
Please don't disconnect your device from your PC or
the power supply until the update is completed.
Click to expand...
Click to collapse
PDA is off, nothing happen... I was wait about 1/2 hour and then I take my PDA from cradle...
Nothing happen...
Now, the only thing I see is SERIAL (top of screen when out of cradle and USB when I put the PDA on cradle) and v2.06 (down to screen).
Try to reset, hard reset... nothing...
Can anyone help an moron like me ??? (I'm reaaly moron, not practice with the PDA's)
(I use Vista Business, I update Windows Media Device Center before this...)
Regards...

read wiki?
Did you follow the steps as indicated in the wiki? As you upgrade from 2003:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade1_WM2003SE0
See next page for Vista related issues...
Read and good luck!

Yes, I follow that steps...
The problem now is: I cannot acces my PDA, I can't revive it...
How can do that ?
Thanks...

Hi, You say:
Now, the only thing I see is SERIAL (top of screen when out of cradle and USB when I put the PDA on cradle) and v2.06 (down to screen).
Well i guess this is the bootloader, so when you connect the phone to the cradle you can upgrade??
Success

As MuratNL says: you are in bootloader. Connect the cradle (with PDA) to your PC (SERIAL changes to USB). Now execute the rom upgrade file from your PC and upgrade should begin.
If you have problems with connection and Vista read wiki (see above link) or try the upgrade from a WinXP machine...

I try this, but nothing happen.... Tonight I try with an XP Pc...

OK, I follow the guide posted by bins and everything goes OK...
(The I put an Italian ROM [ WM6 ] and run perfectly)
Thanks

Just a quick note:
i've experienced that thing so many times
that it's safe to say that:
IF the rom copying aint started yet, meaning YOU DONT SEE the % screen...
and if you've been waiting for that to appear so long...
and you're stuck at the:
Checking the information on your device ... Please wait ...
Please don't disconnect your device from your PC or
the power supply until the update is completed.
Click to expand...
Click to collapse
you can disconnect the BA to the cradle withouth harming the BA.
1. you can disconnect/takeoff the BA from the cable
2. on pc, terminate the upgrade process
(taskmanager terminate the RUU - "MaUpgradeUt_NoID.exe")
3. reconnect your BA still on "Serial/USB" screen
4. restart your RUU again...
that would work flawlessly. trust me. i can vouch for that.
unless you saw the Rom Copy % Screen...
"DONT TOUCH YOUR UNIT or YOUR PC or YOUR CABLES"

PC restarted while upgrading P3600 Radio. Please help.

Ok so I was upgrading my radio on my P3600 to 1.41.00.11 to enable GPS and when it started upgrading, the status bar started on the PDA (as per trinityguides.info's instrucions) but it didn't on my computer. My computer then switched itself off, was dead for about 3 seconds, then restarted itself. I pulled the USB cable from the PDA and now it is stuck in a bootloader style screen, but sais,
TRIN100
IPL-0.50
TRIN100 MFG
SPL-1.30.Olipro
A soft reset does nothing, neither a 'Battery pull-out'
I think that I am stuck in Hard SPL (according to Trinity Guides). Can anyone help me get the PDA back to normal so I can re-flash with the new Radio please? Thanks Alot.
P.s If it is of any relevance, My PDA was not synced with Activesync, But before the flash, I downloaded Activesync 4.5 to fix the 'Generic RNID device' problem on XP. It was identified on my pc as 'Mobile device' in my computer, as far as I can remember.
Sorry if this thread is not new to the site but as a noob (lol) im not really 'broken in' to the site yet. Thanks again for your help.

Hi everyone,
After further research, I reckon I should do the following:
1. In hard SPL, Connect it to another XP computer (my laptop)
2. Untick box called 'Enable USB connections' or whatever in Activesync 4.5
3. Open the ROM of my choice and Double click 'upgrade' or whatever
ROM][WWE][30.10.2008]Karmba_a Diamond Blue For Trinity
4. Wait for the ROM to install
5. Let the trinity soft-reset
6. Done!
7. Upgrade to radio '1.41.00.11' off trinityguides
8. Wait for the radio to install
9. Done!
Please tell me if im wrong so I know if there are any other steps to take. Thanks alot.

Ok guys, I guess, with time I solved my own problem. I did in the end connect my PDA to my XP laptop and used 'splxploit' (thanks to whoever made/programmed this!) which unbricked my device. Now when I tried to upgrade my radio again to a different version, because I have Olipro 1.30 installed instead of 1.20, I was unsuccessful. This shall be what I do next so I guess this thread is not needed anymore.
I'd appreciate it if one of the mod's would close this thread to try and save precious server memory, or can I do it myself (soz im new(ish) to the site!)?
Cheers Guys.

step by step guide to liberate > hard spl > flash Rom

Ok to help the new users on this site iv decided to put toghther a guide on how to liberate > hard spl > flash Rom for your shift.
Step one
liberate your HTC shift
heres some great instructions with a video of the whole process
http://www.modaco.com/content/forum/266537/View-Topic/
at this stage you do not need to go an install IE/Office etc you just need to liberate the device so you can use the USB tools.
step two
make sure USB tools is working run this on your Snapview side and on vista windows mobile device centre should open up and ask you to link your device(no harm i followed through and unticked all boxes.
step 3
follow these instructions on this thread to hard spl your device.
(now at this stage when you are following these instructions make sure on your snapview side that you have disabled your modem and USB tools is running and you have the 2 arrows at the top)
on vista side make sure your device centre has picked up your device. Also do not have any USB devices connected to your shift (as this causes a problem and hangs with a disabled USB message!!!)
follow these instructions---
http://forum.xda-developers.com/showthread.php?t=406606
Step 4 (almost there)
download a rom of your choice
my current fav is i00's rom
http://forum.xda-developers.com/showthread.php?t=480525
extract the rom you should have 2 files in the folder
CustomRUU.exe
RUU_Signed.nbh
if you can only see one file open winrar and then go through win rar to extract -
run the .exe adn thats it.
if it fails ....
on vista bring up comm manager click on advance and reset snapVue
check to see if its restarting and then restart vista
now first go into vista
launch device windows mobile device centre
click on mobile device settings
connection settings
untick allow USB connections
now go into snap view run USB TOOLS
give it a minute
go back into vista
run the rom update......
if you follow this through each stage the steps will make sense to you eg USB tools etc
good luck
__________________

Thanks, added to Shift FAQ

dear i need your help
i hope you can
i will be so greatful for you so much
i did all the steps above with every thing ok
but the last one i could not flash a new rom
from here
http://forum.xda-developers.com/showthread.php?t=480525
Update 20090307
Update 20090309
i did try every thing but the CustomRUU.exe file could not run
i do not know why is that
i really think that i have tried everything
but for sure i have been missing something
would you please tell me the steps or what to do ?
N2h said:
Ok to help the new users on this site iv decided to put toghther a guide on how to liberate > hard spl > flash Rom for your shift.
Step 4 (almost there)
download a rom of your choice
my current fav is i00's rom
http://forum.xda-developers.com/showthread.php?t=480525
extract the rom you should have 2 files in the folder
CustomRUU.exe
RUU_Signed.nbh
if you can only see one file open winrar and then go through win rar to extract -
run the .exe adn thats it.
if it fails ....
on vista bring up comm manager click on advance and reset snapVue
check to see if its restarting and then restart vista
now first go into vista
launch device windows mobile device centre
click on mobile device settings
connection settings
untick allow USB connections
now go into snap view run USB TOOLS
give it a minute
go back into vista
run the rom update......
if you follow this through each stage the steps will make sense to you eg USB tools etc
good luck
__________________
Click to expand...
Click to collapse

i did solve it
you have to run the file by clicking right click on the file and run as adminsterator

HTC USB Tool
I cannot attach the unit, is there a proces to troubleshoot the usb tools

on the vista side in comm manager make sure that you have turned off wifi - modem - bluetooth, then click on advance and reset snapview, then reset vista and try again once its all loaded up, if it still does not work, uninstall mobile device manager on vista and reinstall again, treat it exactly the same as if you where having issues trying to connect your phone via cable to your laptop/pc....

Is there a Hard SPL for the CDMA Shift ? Do any of the cooked roms work in the CDMA version ?

HELP ME
excuse me for bad english
then
- i liberate the snapvue
- i hard spl my device
snapvue is as after hard reset
i havent usb tool
how to connect snap vue to vista
i must liberate again ?
i'm in a loop
in fact custum ruu does't open
HELP ME

Same problem with me too...Please help us.
Same problem with me too...Please help us.
albyboy said:
HELP ME
excuse me for bad english
then
- i liberate the snapvue
- i hard spl my device
snapvue is as after hard reset
i havent usb tool
how to connect snap vue to vista
i must liberate again ?
i'm in a loop
in fact custum ruu does't open
HELP ME
Click to expand...
Click to collapse

always back to initial snapvue after hardSPL
Hi, same kind of situation here.
I have a problem when trying to HardSPL my shift:
rom version 1.30.414.1 wwe
rom date 02/26/08
radio version 1.58.21.23
protocol version 25.65.30.04H
liberated, UsbTool & SoftReset work well
IE, office mobile, total commander, notes installed & work fine
enableRapi OK
but when proceeding with ShiftHardSPLFinal, when it flashes, It goes from 0%
to 100% within 2 seconds and after the shift reboots, I have the original snapview !!!!!
I did it 3 or 4 times, same result.
followed http://forum.xda-developers.com/showthread.php?t=406606&page=16 post # 158 - Cmonex: took battery out, and post # 160 - KOS : uninstalled Origami, disabled UAC,
still same problem : instant install of version 1.00xxx, and ......... back to initial snapvue, ( not liberated)
would you have any idea ???
thanks for your help

dude if it goes from 0-100 in a few secs may be it was a correput download- re download and try again-
sorry cant be more help at the moment - i no longer have a shift-

N2h said:
dude if it goes from 0-100 in a few secs may be it was a correput download- re download and try again-
sorry cant be more help at the moment - i no longer have a shift-
Click to expand...
Click to collapse
Thanks I had not thought about this possibility, too much focused on complex possibilities, I will try again.

vilus said:
Thanks I had not thought about this possibility, too much focused on complex possibilities, I will try again.
Click to expand...
Click to collapse
EDIT: nope, with freshly downloaded ShifthardSPLfinal file, same problem.

vilus said:
EDIT: nope, with freshly downloaded ShifthardSPLfinal file, same problem.
Click to expand...
Click to collapse
Hi all, sorry for my english.
My experience is almost the same. In my opinion the HSPL process is not progressively indicated, but it happens regularly. Moreover, an hard reset follows the precess, thus, at the end, me too found WM in factory default mode. I liberated WM again, but till now i wasn't able to flash another ROM just to check if my Shift has been HardSPL'ed.

After many days without sleeping , i've just made the first call with my shift. Thank you, thank you and thank you.
we are waiting for keyborad solution, it's AZERTY but it shows QWERTY when typing.
Thank for all you did, you do and you'll do for us.

HELP!
I have been searching for possible solutions but cannot find one. Is it possible to Liberate a shift without a working sim card. I left ATT for Sprint years ago, so I do not have an active sim card.

Hspl error check THE picS

HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help

SYRIAN4E said:
HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help
Click to expand...
Click to collapse
Might have been more help asking in the hspl thread but nevermind . Try a different cable (most mini usb cables will do)

SYRIAN4E said:
HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help
Click to expand...
Click to collapse
no need to go crazy, this can be fixed.
you shouldn't enter the bootloader yourself, it won't flash that way.
what error did it say in automatic mode?

syrian
tha messeage talk about turning off my firewall
and the server is off
and this is my first hspl

SYRIAN4E said:
tha messeage talk about turning off my firewall
and the server is off
and this is my first hspl
Click to expand...
Click to collapse
ok did you turn firewall off? turn proxy off too, if you have a proxy.
if that doesn't sort it, I can still help you if you message us via this link: http://support.htc-unlocks.com/

syrian
i change the usb and disable the proxy and turn off all my firewall and antivirus
i think the proplem from something lagging from the hspl software
cuz i enter the bootloader and i start manual flash and it's respond and show to me the update button and i press it and tell my software version and if i wanna change to oilnex version and i press it and show to me the percentage image on the pc and in the phone then i wait then nothing happend

SYRIAN4E said:
i change the usb and disable the proxy and turn off all my firewall and antivirus
i think the proplem from something lagging from the hspl software
cuz i enter the bootloader and i start manual flash and it's respond and show to me the update button and i press it and tell my software version and if i wanna change to oilnex version and i press it and show to me the percentage image on the pc and in the phone then i wait then nothing happend
Click to expand...
Click to collapse
you shouldn't enter the bootloader like that, the flash won't work that way.
I replied to your priv. message

syrian
is there any hope CHECK THE PICTURE
1st - the cable is work well cuz i update the device with it from the offical htc website
2nd- the picx
3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK
4TH- I START THE manual FLASH
2nd- more INFO
RED LINE : TOPA100 32M
SPL-2.51.0000
MicroP-Topaz (LED) V10
TURBO HW/TURBO SW
GREEN LINE : TP MFG DATA
502,547 170,876
173,200 834,210
828,869 Calibrated
BLUE LINE : E M P T Y
WHITE LINE : U S B

SYRIAN4E said:
is there any hope CHECK THE PICTURE
1st - the cable is work well cuz i update the device with it from the offical htc website
2nd- the picx
3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK
4TH- I START THE manual FLASH
2nd- more INFO
RED LINE : TOPA100 32M
SPL-2.51.0000
MicroP-Topaz (LED) V10
TURBO HW/TURBO SW
GREEN LINE : TP MFG DATA
502,547 170,876
173,200 834,210
828,869 Calibrated
BLUE LINE : E M P T Y
WHITE LINE : U S B
Click to expand...
Click to collapse
the screenshots are very helpful in seeing what your problem is.
ok, after 3rd step now try copying Manual SSPL exe (link: http://forum.xda-developers.com/attachment.php?attachmentid=232407&d=1254155476) on the phone, run it, it should then show SSPL screen on the phone. then use the Manual flash mode on the PC. let me know if it works that way

syrian
the device get LAG when i launch the manual sspl and i start manual flash even whene it's lag
and here is the picture

SYRIAN4E said:
the device get LAG when i launch the manual sspl and i start manual flash even whene it's lag
and here is the picture
Click to expand...
Click to collapse
what do you see on the phone screen at this point?

syrian
nothing just the file maneger when i launch the manual sspl cuz the device lag

SYRIAN4E said:
nothing just the file maneger when i launch the manual sspl cuz the device lag
Click to expand...
Click to collapse
ok you did step "3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK"
and then you run the manual sspl EXE on the phone, it still lags ?
I'm asking to make sure you did not do a hard reset or anything (I mean, don't do hard reset)

syrian
i just did it in ever way that you can imagine
and i think that the manual is the proplem i'm sure
is ther any hspl type haha we can use

SYRIAN4E said:
i just did it in ever way that you can imagine
and i think that the manual is the proplem i'm sure
is ther any hspl type haha we can use
Click to expand...
Click to collapse
ok one last check.. send me a screenshot of your phone showing the IMEI to make sure it's OK.
but do not post the screenshot publicly, send it in private message.

syrian
come on xda help me lol

SYRIAN4E said:
come on xda help me lol
Click to expand...
Click to collapse
alright I realized that the second file was the wrong version. I sent you the correct file in PM, let me know if it worked

syrian
OMG it's WOrk good
thanks a LOT for you
i own you
LOT
LOOK how much time it take to fix this proplem LOL
now i have another proplem and it is if you won't
is how to download the duty or energy rom cuz they are upload on HOTFILE and RAPIDSHARE LOL
and i thanks for the second time and love to know what was the prolem
SYRIAN4E

SYRIAN4E said:
OMG it's WOrk good
thanks a LOT for you
i own you
LOT
LOOK how much time it take to fix this proplem LOL
now i have another proplem and it is if you won't
is how to download the duty or energy rom cuz they are upload on HOTFILE and RAPIDSHARE LOL
and i thanks for the second time and love to know what was the prolem
SYRIAN4E
Click to expand...
Click to collapse
glad to help. as I said, the manual SSPL in the thread was the wrong version. I forgot to update it at one point, will add it in the thread now. (most people can just go and use automatic mode so nobody noticed there was an issue with the file.)

Hi all
I really need some help please!!
I think I have read and searched and tried steps by step all the posts and threads on this, none of them work for me,
Ive flashed my HD2 & TD2 with HSPL, radios and roms many times in the past. I have a stock rom on my TD2, (havent flashed a cooked one yet but did on my HD2 and worked great),
the problem is when I try flash anything, (HSPL,Radio's and Roms)
I connect with WMDC on windows ultimate 64x and go through all the steps, the phone disconnects from WMDC when loading the tri-color screen, and installs the HTC sync drivers fine, and then (my problem) it hangs on 0%. this happens regardless of what I'm flashing after a while brings up the communication errors 208 & 260. this doesnt have any effect on the software HSPL or radio as a soft reset returns back to the homescreen just fine. I am running HSPL 1.8.3. , radio 4.49.25.17 and a shiped stock wm 6.5.
This is what Ive tried so far:
I have used 3 different micro USB cables,
updated my .net fx to 4.1
I have tried different Ruu's such as custom Ruu, Ruu from topaz, Ruu, supplied with Hspl, flashes center and KaiserCustomRUU.exe and a few others.
Ive tried the white screen fix many times. including the SDA unlocker and stuff.
I ve tried manual and automatic.
tried entering the the Tri-color screen manually and via the Ruu.
I tried different computers and different operating systems (W7ultimate and XP 32Bit and 64Bit)
tried active sync WMDC 6.0 and 6.1
Ive removed the SD card and sim and have tried flight mode
Restarted pc's mobile any reinstalled WMDC many times.
Ive tried renaming to the HSPL, radio and Rom to TOPAIMG.nbh , put 1 by 1 on formated fat32 SD card, run from Tri-color menu. all of them just hang on
loading....
Have tried mixing and matching Ruu's with HSPL's, Roms And radios and everything else i can think of, after 18 hours of this I am fed up and decided i need some help
Thanx in advance
ok
i have now download the official RUU_Topaz_S2_HTC_WWE-AFK_2.53.421.3_Radio_Signed_Topaz_61.44etc.25.35_4 .49.25.91_Ship.exe Rom
and it worked with no problems.
it updated my HSPL from 1.83 to 2.51 and radio version to 4.49.25.91 which was exactly what i was going for.
The problem now is that i still cant change my HSPL, RADIO or flash a custom Rom which is what I need. it hangs on 0% and now gives me a 262 error which states that:
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
which is not true as if a reboot it doesn't continue the update and just returns to the home screen as normal
help?