Database Develop

Tilt Goes Silent - I think bluetooth related

Hi everyone. I have had my Tilt for 4months now and it has given me a lot of joy. I have flashed and reflashed with no problems at all. I am currently using Schap's 4.31 Rom with 1.27.12.11 radio.
About a month ago i installed a new car stereo that has bluetooth connectivity with my phone - worked like a charm, paired very easily and generally appeared to be working with no probs.
Then i noticed that if i was in a bluetooth conversation and somebody else was calling (on call waiting), if i switched calls i could not hear anything, and if i ignored the second call, when the person on call waiting hang up, both conversations were terminated. I thought it was odd, but i just deactivated call waiting and thought, "let them try calling me later".
The other, a lot more serious problem, is that sometimes, randomly as far as i realised, the phone will go totally silent - incoming calls won't ring, and when i try to make a call, when i press "talk" then phone does not make that beep that it makes when an outgoing call is initiated. Should the person i call pick up i cannot hear them at all.
A soft reset takes care of this problem, but it has happened to me 3 times already, and i think it was after a bluetooth call.
Has anybody faced this problem before? I need to be available on the phone 24/7 due to my work and i really need to find a solution for this. Yesterday afternoon i took a nap for 45 minutes and had six missed calls that i never heard cause the phone never rang.
The phone is always on "ring" and at full volume.
Any ideas would be welcome.
Thanks
Alkis

Same issue
I'm assuming since I also am facing this same problem that it is not uncommon. It seems to me that it happens after a bluetooth device is turned off. Somehow it sets the volume on everything to mute. I thought only a soft reset would fix it until I discovered that it was just shutting off the volume. Still annoying, though.

Tilt problems with phone going silent
This problem has occurred with my phone every since upgrading to the WM 6.1 and it is related to a bluetooth device being hooked up. Often when someone calls the ringer will go from vibrate to on, but the volume turns all the way off. It will then cycle to off completely. The cycling occurs when a call comes in or when I hang up. I can stop this problem from happening by disconnecting the bluetooth head set. I have tried three different headsets and the problem occurs with all of them (Jawbone I, Jawbone II, and Plantronics) so I know it is not the brand of headset. HTC said to try a download of a screen dimmer problem, but have not done that yet. Anyone have any better advice?

did u guys ever find a solution to this?
its quite annoying missing calls because my phone decides to go silent for some reason

Same issue with GPS
I have the same issue, even when using software that accesses the GPS via bluetooth port. Muting is irritating, but at least voicemail catches messages. What really bothers me is that sometimes the mute is turned off and the volume up, especially when in a private meeting where we do not want interruptions
Gregg

HTC Tytn II bluetooth causes silent setting
I too have had the issue where my phone will go into total silent mode after using my bluetooth stereo hands-free feature. It doen't happen after using my bluetooth headset though.
It happens pretty regular that after using the bluetooth hands-free of my JVC car stereo that when I take the phone elsewhere it is totally silent. no ringer, no alarm (Ptravel alarm is what I use), no audio if I make a call (or receive a call).
It also will cause the phone to be silent on subsequent calls on the bluetooth stereo hands-free: ie: I take a call, hang up and another call will come in and I can answer it but have no audio.
My Tytn II is running the HTC (AT&T) WM 6.1 upgrade. The only thing I have done is use the Advanced configuration manager and the Kaiser tweak to change a few settings for performance and visual enhancements.
I see others are having the same problems.....Has anyone else used the tweaks and maybe that is root of the problem?
Has anyone discovered a fix (really important). My only options are to soft reset every time I get out of the car or not use the JVC bluetooth capability (which is why I replaced the stock radio in the first place).
Thanks

Hi rrackman,
I'd advice for you to look at the following thread:
http://forum.xda-developers.com/showthread.php?t=438457
It's quite long, so better subscribe to it and wait for responses. Several people with Tilt's have the same problem. Myself I have a JVC NX-7000 and an unbranded Kaiser (HTC TyTN II). It works fine with WM6.0, but I have the same issues you mention with WM6.1. First advice while we're searching for the solution: downgrade to WM6.0...
Regards,
Nika.

Is there a solution to this problem?

Try WM6.0 ROM - check out the thread I mention in my sig.
Regards,
Nika.

I did indeed take a look at the thread you linked earlier. Sorry for making the quick post earlier, I should have mentioned that this is regarding the "unexplained volume drop to zero" symptom, not the NSI symptom. Fortunately I don't have the NSI problem, just the drop to zero problem.
Of course downgrading to 6.0 would be the key solution, was just hoping to find a way to avoid doing just that. My phone never had the problem prior to 6.1 and was running the exact same list of applications and settings.

"Device Not Ready" in WMP when call comes in..

I get the "Device Not Ready" popup in Media Player when a call comes in and switches over to my BT headset. It is frustrating to constantly have to clear the popup and try to yet again seek to where the hell I was on a podcast when the call came in! Is there a fix for this or is it just a "feature" of WMP and/or WinMo 6.1? I am hoping someone has a magic reg setting to make WMP behave on audio transfers to and from BT.
I have MSVC working fine via my Plantronics Voyager 510 and just want my music or podcast to pause when a call comes in then switch to my BT for the call duration then resume playing via speaker after the call is done.. is this asking too much?
This happens with every ROM I've flashed.. (although I only have flashed Dutty's last 4 releases). So, I am thinking others have it happen and live with it or I am just not tweaking my tilt properly. And, yes, I do a hard reset after every flash.. and everything else works fine.
I've searched but can't find if there is a solution to this. Any advice is greatly appreciated.
Thanks..

Hmm.. since no takers.. can u tell me if it happens to u?
With no replies on my post.. can anyone just confirm that this happens to them as well? I would think at least some of the xda peeps would have the phone playing a tune or podcast between calls. Does your phone switch audio without the "Device is not ready" error?
Just trying to see if it's only me...
Thanks.

I listen to MP3s (not WMP but Pocket Player or S2P) all the time while my phone is connected to my car's bluetooth handsfree system. I have never once observed a "device not ready" error pop-up when a phone call arrives. The music pauses and the handsfree takes over and starts ringing.
Might want to look at this thread: http://forum.xda-developers.com/showthread.php?p=2083364 as it seems that some people are seeing the same problem as you.

Rumball,
Thanks for your post. I guess it might be my bluetooth giving me the problem then. I've been needing a reason to buy a new z9.. so hopefully it will behave better since it's BT 2.0.
Thanks again for letting me know it works the way I imagined it should!

Bluetooth stops/crashes when connected to Car kit

Hi,
When my phone is connected to my car kit (Opel/Vauxhaul UHP) bluetooth sometimes stops randomly. I can turn bluetooth on again with the commmanager and everything is working again. But it can hapen again after a few minutes.
Does anyone have this problem to or even better a solution?
I allready tried all the different Radio Roms, but this didn't solve my problem.

Well with mine i have some hickus but it just happpends once a while.
Most irritating about Diamond and BT in my opinion is that wa have no equalizing for it. and the sound setup from the begining is horrible.
Asked here if anyone has a solution before but none replied.
But as far 2 your problem no. And i use a Pioneer system in my car.

Mauser.NET said:
Hi,
When my phone is connected to my car kit (Opel/Vauxhaul UHP) bluetooth sometimes stops randomly. I can turn bluetooth on again with the commmanager and everything is working again. But it can hapen again after a few minutes.
Does anyone have this problem to or even better a solution?
I allready tried all the different Radio Roms, but this didn't solve my problem.
Click to expand...
Click to collapse
HI
Same was happend with me (Opel), when my battery is low.

orsiga said:
HI
Same was happend with me (Opel), when my battery is low.
Click to expand...
Click to collapse
Mine is not low on battery, but I shall try it once connected to the cigarette lighter.
Nobody else has this kind of problems??

Mauser.NET said:
Mine is not low on battery, but I shall try it once connected to the cigarette lighter.
Nobody else has this kind of problems??
Click to expand...
Click to collapse
I've a JVC head and my bluetooth has no problem.

I have a Honda Accord with handsfree built in and I too am having problems. The phone and car both agree that a connection has been made but when i use it to either ring out or receive a call the radio mutes and when receiving the ringing tone sounds over the car speakers but I can`t hear the caller except on the phone which isn`t very useful. Would a ROM or radio upgrade help or is it just a compatibility problem

davemazo said:
I have a Honda Accord with handsfree built in and I too am having problems. The phone and car both agree that a connection has been made but when i use it to either ring out or receive a call the radio mutes and when receiving the ringing tone sounds over the car speakers but I can`t hear the caller except on the phone which isn`t very useful. Would a ROM or radio upgrade help or is it just a compatibility problem
Click to expand...
Click to collapse
I had this kind of problems also. Also syncing the phonebook gave me problems. You could try JETware, this solved almost all my problems, except now the bluetooth crashes

Mauser.NET said:
I had this kind of problems also. Also syncing the phonebook gave me problems. You could try JETware, this solved almost all my problems, except now the bluetooth crashes
Click to expand...
Click to collapse
Thanks Mauser. I tried Jetware as you suggest and I`m afraid it didn`t help in fact I think it crashed the handsfree system in the car like you. This is the final nail in the coffin for my Diamond. I just can`t get used to it so it`s off to Ebay with it.

davemazo said:
Thanks Mauser. I tried Jetware as you suggest and I`m afraid it didn`t help in fact I think it crashed the handsfree system in the car like you. This is the final nail in the coffin for my Diamond. I just can`t get used to it so it`s off to Ebay with it.
Click to expand...
Click to collapse
I'm sorry to hear that
I am very pleased with my Diamond... I would sooner put my car on eBay than my Diamond
Did you try to check almost everything on in the advanced settings of Jetware? I have also limited the phonebook sync to max 5 entries to debug and on the site of Jetware there wat a fix for Opel car kits.
Keeping my fingers crossed, but until now I haven't experienced any bluetooth crashes.

Mauser.NET said:
I'm sorry to hear that
I am very pleased with my Diamond... I would sooner put my car on eBay than my Diamond
Did you try to check almost everything on in the advanced settings of Jetware? I have also limited the phonebook sync to max 5 entries to debug and on the site of Jetware there wat a fix for Opel car kits.
Keeping my fingers crossed, but until now I haven't experienced any bluetooth crashes.
Click to expand...
Click to collapse
Thanks again Mauser. I tried various settings but without any success, I think the phone is just not compatible with the Honda. Having said that I don`t have much luck with bluetooth at all on the phone. More often than not It just won`t detect other bluetooth devices and when it does it won`t send or receive files so it`s time for it to go and I can go back to a trusty Nokia

Problems here with BT connection to car kit, too. I'm using the built-in car-kit of an Audi A4 (standard one not that with navigation, remote SIM, etc). I've noticed the following issues:
- when I try to make a call, the CD is cut off but NOTHING is heard in the car speakers UNTIL the other party answers the call (and then I start the conversation). No ringing tone, no nothing. I cannot hear the busy tone, or network failure/congestion tone and this is annoying since I have to keep an eye on the phone to see what's happening. I found myself checking the phone when, after calling someone, nothing happened and in fact I got a busy tone and the call ended.
- sometimes, when I receive a call, the CD stops playing but when I answer nothing is heard from the car speakers but only from the phone (as davemazo said also).
- when I receive a call, I hear in the car speakers a "standard" calling tone, not the ringtone I have assigned for that contact
I have to mention that with any Nokia I had before (and still have one as a second phone), these problems do not exist. I know there is a compatibility between Audi factory installed car-kits and Nokia, but BT is a standard and most of the functions should be supported despite the phone model/type. I've tried also with an iPhone and it's working great, as my Nokia do. I don't understand why it is like this with the Diamond. In fact, I think it is not related to Diamond itself...it's doing like this with ANY Windows Mobile device I've tried in the past (Orange C600, Samsung I600).
Are there any solutions for this? A CAB, a new BT radio, a software, anything?... I don't want to buy a new BT car-kit and try with different models until I find something compatible
Thank you for any info/tip

Rapier said:
Problems here with BT connection to car kit, too. I'm using the built-in car-kit of an Audi A4 (standard one not that with navigation, remote SIM, etc). I've noticed the following issues:
- when I try to make a call, the CD is cut off but NOTHING is heard in the car speakers UNTIL the other party answers the call (and then I start the conversation). No ringing tone, no nothing. I cannot hear the busy tone, or network failure/congestion tone and this is annoying since I have to keep an eye on the phone to see what's happening. I found myself checking the phone when, after calling someone, nothing happened and in fact I got a busy tone and the call ended.
- sometimes, when I receive a call, the CD stops playing but when I answer nothing is heard from the car speakers but only from the phone (as davemazo said also).
- when I receive a call, I hear in the car speakers a "standard" calling tone, not the ringtone I have assigned for that contact
I have to mention that with any Nokia I had before (and still have one as a second phone), these problems do not exist. I know there is a compatibility between Audi factory installed car-kits and Nokia, but BT is a standard and most of the functions should be supported despite the phone model/type. I've tried also with an iPhone and it's working great, as my Nokia do. I don't understand why it is like this with the Diamond. In fact, I think it is not related to Diamond itself...it's doing like this with ANY Windows Mobile device I've tried in the past (Orange C600, Samsung I600).
Are there any solutions for this? A CAB, a new BT radio, a software, anything?... I don't want to buy a new BT car-kit and try with different models until I find something compatible
Thank you for any info/tip
Click to expand...
Click to collapse
Hi Rapier,
I also had a SPV C500, MDA Compact, Qtek 8500, Samsung I600, HTC Touch Dual and now the Diamond. The only one which gave me no troubles was the SPV C500, but I think that was because this phone didn't support phonebook synchronization and had no network identification/signal strength over bluetooth.
After the SPV C500 it went wrong. First I noticed that after a hard reset it worked for a few days. Later (about 2 years later ) I found out that it was because the call history was going to long to sync over bluetooth.
Then I found Jetware in which you can limit syncing to any number of items. They even had a fix for the connection to my carkit.
Unit now... it works like a charm... but keep my fingers crossed
I don't know if your carkit is a Audi UHV, but I saw that they had a fix for that too! You have to just install Jetware and then run the fix-file from your phone. Good luck!!
P.S. I am in no kind related to Jetware, I just found out that it worked for me.

Yes, I have an Audi UHV 6634. Thank you for the info, I'll try that and post the results here. Though, my car-kit is not the advanced one and I don't have to sync anything with it (contacts or something else). It's most working as a plain hands-free device, no extra functions...speaking of which, I've noticed that on the phone is detected as "hands-free"...why not "car-kit" as I know a car-kit has other functionality as well? This is the "standard" BT device for any audio enhancements (even if it is a car-kit not a BT headset), or I have to activate something to be recognized as car-kit?

Mauser.NET said:
Jetware? I have also limited the phonebook sync to max 5 entries to debug
Click to expand...
Click to collapse
my Honda system doesn`t read the sim I can only dial out via handsfree using contacts i`ve entered into the Honda system otherwise I either have to read the number to the system and it will ring out (most of the time anyway) or make the call on the phone (illegally obviously) cancel the call and then say "redial" and the system makes the call. So uless I`m misunderstanding this setting I don`t think it will help me.
I`ve searched the Jetware website and I couldn`t find a fix for my Honda

UPDATE: So...I've downloaded it, install it on my Diamond (including the extension file for Audi UHV) and...no change. Everything as before with both issues. Disappointed, I've uninstalled Jetware then...surprise. AFTER uninstall, I can now hear through my car's speakers the ID ringtone Maybe some BT settings were altered and remained like this after uninstall, but I don't know why it didn't work when Jetware WAS installed...strange.
Anyway, many thanks...at least half of the problems are now solved and this only by install/uninstall a program...that's cool. I must now find a way to make the car kit ring when I make a call, this is still an issue.
P.S. I've seen that Diamond support Headset and Handsfree profiles...and when connected to my car kit is set as Handsfree. I suppose this is better than Headset...but still no ring out tone.

Rapier said:
UPDATE: So...I've downloaded it, install it on my Diamond (including the extension file for Audi UHV) and...no change. Everything as before with both issues. Disappointed, I've uninstalled Jetware then...surprise. AFTER uninstall, I can now hear through my car's speakers the ID ringtone Maybe some BT settings were altered and remained like this after uninstall, but I don't know why it didn't work when Jetware WAS installed...strange.
Anyway, many thanks...at least half of the problems are now solved and this only by install/uninstall a program...that's cool. I must now find a way to make the car kit ring when I make a call, this is still an issue.
P.S. I've seen that Diamond support Headset and Handsfree profiles...and when connected to my car kit is set as Handsfree. I suppose this is better than Headset...but still no ring out tone.
Click to expand...
Click to collapse
No thanx! I'm glad I could help

Mauser.NET said:
Hi Rapier,
I also had a SPV C500, MDA Compact, Qtek 8500, Samsung I600, HTC Touch Dual and now the Diamond. The only one which gave me no troubles was the SPV C500, but I think that was because this phone didn't support phonebook synchronization and had no network identification/signal strength over bluetooth.
After the SPV C500 it went wrong. First I noticed that after a hard reset it worked for a few days. Later (about 2 years later ) I found out that it was because the call history was going to long to sync over bluetooth.
Then I found Jetware in which you can limit syncing to any number of items. They even had a fix for the connection to my carkit.
Unit now... it works like a charm... but keep my fingers crossed
I don't know if your carkit is a Audi UHV, but I saw that they had a fix for that too! You have to just install Jetware and then run the fix-file from your phone. Good luck!!
P.S. I am in no kind related to Jetware, I just found out that it worked for me.
Click to expand...
Click to collapse
Hello,
I have a Mercedes car kit and facing the same issue as you: everything works perfectly for a few days when hard-resetting my device, even with my 500+ contacts (they are loaded in less than a minute), but after a few days/weeks I can't get to have my call history or contacts displayed in less than half an hour!
Yesterday I thought I'd just hard reset my device because I had this problem again, but unfortunately it didn't work!
Guess what I have done differently this time: yes, I backed up and restored my call history, which I hadn't done the previous times! So I guess it is indeed related to the call history, but I can't test for now!
I have installed JetWare and limited the call history to 5 numbers, I'll try this tonight and I'll keep you informed...

Hello,
So I have tested this yesterday (installed Jetware and limited the call history to 5 numbers), and now it works FLAWLESSLY! I can browse through my 500 contacts instantaneously when I pair my phone with my Mercedes car kit.
So, in my case it was also clearly the CALL HISTORY that was causing problems... A BIG BIG thanks to Mauser for pointing out this!

I'm also having problem connecting my Diamond to my Volvo S80. All the other functions work except that I could not hear the other party through my car stereo and I also could not diconnect the call with my car end key.
I'll try the Jetware and I'll report back later. Thanks for the pointer.

turt said:
A BIG BIG thanks to Mauser for pointing out this!
Click to expand...
Click to collapse
No thanx! ... glad I could help

No incoming or outgoing audio. Anyone ? Anyone ?

Hello. I've been relentlessly searching everywhere for a solution to my plight.
My Diamond touch works fine for the first few incoming and outgoing calls but then all of a sudden there is no incoming or outgoing audio when I make or receive a call. I.E. the call connects but I can't hear the caller and they can't hear me. The phone still rings and caller display still works. Likewise I can still place a call in the normal way. Just no audio in either direction. Soft reset sometimes restores normal operation but sometimes a hard reset is required.
The phone was originally on UK Orange network but is now unlocked and running on UK O2.
I got to grips with flashing quickly enough and I have now tried upteen combinations of roms and radios but nothing seems to help.
Has anyone else had this problem ? Or better still managed to cure it ?
Any help or suggestions would be so so so appreciated.
Oh yeah just in case it's relevent.. The phone seems to work perfectly in every other way. wifi, bluetooth, 3G, gps etc. Battery life is a wee bit pants but I'm not too concerned about that.
Thanks in advance guys !

brianbelfast said:
Hello. I've been relentlessly searching everywhere for a solution to my plight.
My Diamond touch works fine for the first few incoming and outgoing calls but then all of a sudden there is no incoming or outgoing audio when I make or receive a call. I.E. the call connects but I can't hear the caller and they can't hear me. The phone still rings and caller display still works. Likewise I can still place a call in the normal way. Just no audio in either direction. Soft reset sometimes restores normal operation but sometimes a hard reset is required.
The phone was originally on UK Orange network but is now unlocked and running on UK O2.
I got to grips with flashing quickly enough and I have now tried upteen combinations of roms and radios but nothing seems to help.
Has anyone else had this problem ? Or better still managed to cure it ?
Any help or suggestions would be so so so appreciated.
Oh yeah just in case it's relevent.. The phone seems to work perfectly in every other way. wifi, bluetooth, 3G, gps etc. Battery life is a wee bit pants but I'm not too concerned about that.
Thanks in advance guys !
Click to expand...
Click to collapse
M8. I don't think you're on your own on this one. I have the same problem ...or similar. My phone pairs OK but drops the blue tooth connection usually on audio but quite often altogether. Re-pairing is a pain in the A$$. It's definitely a phone issue as I have the older qtek and a nokia that work with my kenwood system without a hitch but pair up the diamond and I'm pulling my hair out after 5 minutes.
I've tried the latest stable radio, setting pin code to 0000 & also turning off security but it still drops connection after an outgoing or incoming call.
Does anyone have a fix for this?

...and jetware 1.3 doesn't solve this either. Installed it the other day and pretty much the same ...audio is fine until a call is terminated and then it drops A2DP but sometimes stays connected on telephone. Other times both drop off!

bt stack
In my case it looks like the BT stack on the diamond is not compatible with the Kenwood DNX8220BT stack. I see quotes that HTC implemented their own stack for the Diamond so could someone put me out of my misery and tell me if it's possible to change the stack to something like that on the wizard as that works flawlessly with my Kenwood satnav?
ADD+

My phone does that weird thing too where I couldnt hear the other person on line. I have manage to found a quick fix for it tho.
Solution 1: During the call (when you notice you cant hear the other person), press the middle circle button (which will activate the screen if dimmed out), then press the speaker icon. This allows you to continue the conversation on speaker with the other person on line without having to soft/hard reset.
Solution 2 (works sometimes): During the call, reduce the volumn, wait a secnd or two, then raise it again.

Bt3030 - Shb6100/7100
Have the same problem with Philips shb7100 and shb6100. i also have tried the Jabra BT3030.
I used and test them on a Tyten and wizard no problem at all.

I had same problem before...found out is hardware problem...sent to htc care and after tat everything ok.

ADD+ said:
In my case it looks like the BT stack on the diamond is not compatible with the Kenwood DNX8220BT stack. I see quotes that HTC implemented their own stack for the Diamond so could someone put me out of my misery and tell me if it's possible to change the stack to something like that on the wizard as that works flawlessly with my Kenwood satnav?
ADD+
Click to expand...
Click to collapse
I have the exact same model (kenwood dnx8220bt and XDA ignito (diamond), same problem where everything is okay but when you go into the contacts menu and try to make a call, BT connection either drops or nothing happens when you try to make the call.... this is a joke.... how can my old HTC P3300 work with it without a problem and this newer Diamond flop like a fish...
any updates or news??

I've the same problem. No Sound after some call or others sounds play. When this happens and if I receive a call the others not listen my voice. This means that when audio disappear, speaker and also microphone not work, like the system can't comunicate with them. The volume control not resolve my problem. I've done HR and with nothing installed in my phone the problem come back again after few minutes. So it's not a problem of third part bad software, but htc orginal software or hardware problem.
Anyone solve it o have idea?
Thanks!

I join the list - having problems with my xcarlink which used to work with my P3300
Tried using A2DP Toggle which helped on the artemis but seems to have NO effect at all on Diamond
The Diamond does connect flawlessly to my jabra earpiece and my Sony ericsson bluetooth speaker

ninja_pimp said:
I had same problem before...found out is hardware problem...sent to htc care and after tat everything ok.
Click to expand...
Click to collapse
I have the same problem. Sent my HTC back twice for repair but still no solution. The first time they didn't found the problem, the second time they replaced the speaker.
What did they do with your phone to fix it?

According to this thread http://forum.xda-developers.com/showthread.php?t=431826 it is a hardware issue. The phone needs to go back to the supplier as it is faulty.

Play Music via Bluetooth "fixed"

This is my first, and only a minor, contribution to the forum; I've been a feeder up till now.
I bought a cheap bluetooth headset for my HD2 for use with my motorcycle satnav and also my HD2 - not that I want to take calls whilst I'm riding, but playing music would be a possibility. It was similar to this:
http://cgi.ebay.co.uk/Bluetooth-V2-...e_Phones_Bluetooth_Acc_ET?hash=item3efab16de4
I paired it with my satnav and could hear voice commands and music as expected. I then paired it with my HD2 and could only get calls, no music playing!!!
I tried looking for settings on the HD2 but nothing made any difference so I decided to look in the registry. After a while exploring I eventually found:
HKLM/software/widcomm/BTconfig/devices/
There were three devices paired (HD2, satnav and my car) so next I had to work out which one. I found that if you look at the nickname for each one, it's decoded into english by the Reg Editor (I use CERegistryEditor). Using trial and error I found that changing the setting "Hideconnections" from "0" to "1" did the trick. I can now hear music through the headset!!!
Well chuffed with myself!!!
PS Perform a soft reset after changing it to lock it in otherwise it resets to "0" after a disconnect.
OOPS! because I was looking for Bluetooth stuff I posted this in the wrong area, sorry!!! Maybe a moderator can correct please?

How bizarre it works by default for me......well done on the find though

Thanks...

It doesnt work for me, im using samsung mono bluetooth. I've tried many methods like btaudio bttoggle.... any help, thanks

All I can suggest is that - like I did - compare settings with something that does work. Maybe because you have a mono headset (mine is stereo) it's not capable of receiving music?

Hi
I could play music and receive system sound in my Jabra mono bluetooth earpiece if, in HD2, I go bluetooth->advance->Audio and check "play system sounds on remote hands-free device". However, after a phone call, the music and sound will be routed back to the phone speaker, though the earpiece is still connected (you can still make/receive phone calls through the earpiece).
The music and sound can only be routed to the earpiece again after a soft reset.
The other observation is that, if there is pause in between music or sound for a period of about 12 to 15 seconds, the HD2 will "suspend" the bluetooth transmission (beep in the earpiece) and resuming the music will cause the bluetooth transmission to be re-established (beep sound in earpiece). This is causing skipping of the first 1 to 2 second of the music / sound.
Have installed BTaudio V1.0. It is working on my HD2 and will keep the transmission constant and no skipping problem.
However, also needing soft reset after phone call.
Does any one has similar experience ? Is this earpiece/ head set related of is this HD2 related issue ?

No one has simialr experience ? Is there a thread on bluetooth related registry tweaks, I have been searching for it but don't seems to be able to find one. Any help will be appreciated.

anzudragon said:
It doesnt work for me, im using samsung mono bluetooth. I've tried many methods like btaudio bttoggle.... any help, thanks
Click to expand...
Click to collapse
+1 as well
I have a Samsung WEP420 mono bluetooth and no success either.

Armes said:
I tried looking for settings on the HD2 but nothing made any difference so I decided to look in the registry. After a while exploring I eventually found:
HKLM/software/widcomm/BTconfig/devices/
Click to expand...
Click to collapse
I don't have that reg key at all! I have a dutch hd2 running stock 1.66. When I try to connect to a parrot party bluetooth stereo box this (most of the time) doesn't work. Once or twice I established a working connection but after trying multiple times with no luck I decided to find a fix for my problem. Now I try to edit my reg with this and it's not there!?

i paired the hd2 with the car kit parrot ck3100... leaving apart that it doesn't connect always... although i have checked in settings to play all phone sounds through BT it doesn't...
i think it's a BT problem of the hd2, or maybe all WM phones... 'cause ițve had issues like this before...
P.S. once it played the music thorugh the car kit... just like this...