There is GSM Radio but can not make a CALL - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Yesterday I was successfully upgrade my BA to WM 6.1, but after several "stuck", I have to Had Reset it. Then trouble came by.... I can not make a phone call but everything at my phone looks ok. There is GSM radio but why can I can not make a phone call ?
plz advise..

flash your official stock rom to your phone then upgrade again with the cooked rom. you should try using the phone after you have flashed your official rom to see if it is working ok.
Then if everything is fine flash your cooked rom

scousemartin said:
flash your official stock rom to your phone then upgrade again with the cooked rom. you should try using the phone after you have flashed your official rom to see if it is working ok.
Then if everything is fine flash your cooked rom
Click to expand...
Click to collapse
thx a lot brother .........
seems my GSM provider had to temporary block my account ( Darn.... I forgot pay the bill )

Related

k-jam, another brick in the wall (dead after rom update)

Hello folks,
Today I flashed with the ROM in thread 'T-Mobile USA 2.17 ROM (Custom)'. After it came up, I ran through the screen align and wizard. When it was all done installing extended rom etc it restarted on its own. After booting back up, everthing was really slow and there was no cell signal. The battery icon had an ! mark on it and when clicked, it says unknown battery. At this point everything keeps freezing and genrally not working including no activesync connection possible. I restarted into the bootloader and tried to flash again. It completed, but now I just get the tmobile boot screen, and eventually it restarts again, never completing the boot. This is when I notice that it doesnt seem to have a radio rom (GSM) version listed, but rather a gap where it should be. I ended up pulling the battery out and trying to get back into the boot loader again, and now I cant get it to power on in any way.
I guess that is enough said. The only other thing to note is that everything was working fine prior to the attempted update, I was merely hoping to get a performance boost, as I was using the original rom.
Any thoughts?
Thanks!
B. Ramsey
Fixed!
No other ROM would install, but in reading back through threads, I found a link to RUU_Prodigy_1081002_108_10910_TMO_US.exe. After installing this, I had my GSM rom back. Then everything worked. I think the not powering on issue had to do with the fact that it sat in the bootloader screen for several hours at one point. Since there was no standby, the battery was wasted. I am attempting to reflash it now to 2.17, we'll see.
No dice
After installing the 2.17 ROM, no more GSM, and same problems. I reflashed back to the previous and it works again..
Re: Fixed!
pterodyne said:
No other ROM would install, but in reading back through threads, I found a link to RUU_Prodigy_1081002_108_10910_TMO_US.exe. After installing this, I had my GSM rom back. Then everything worked. I think the not powering on issue had to do with the fact that it sat in the bootloader screen for several hours at one point. Since there was no standby, the battery was wasted. I am attempting to reflash it now to 2.17, we'll see.
Click to expand...
Click to collapse
THANK YOU SO MUCH for posting this! I also had a brick because of the same setup - trying to use the custom TMOBILE ROM. I had the same symptoms you did - basically non-responsive and no radio stack and no USB connection. I was not getting anywhere with any other ROM. Now, at least I have a working device.
Still no AKU2 though
Let me know if you manage to get an AKU2 ROM on your device!
That's worrisome. Do you know if the CID unlock was successful? (I think it's scripted into that custom upgrader)
If you're feeling adventurous, you could try intalling the custom 2.17 Cingular upgrader I made (it's on the FTP server). If that's successful, then the problem is with the T-MO upgrader. Based on all the folks having success with that T-MO upgrader though, I imagine the only issue might be a corrupt download. If the Cingular upgrader results in the same behavior, then the problem is either with the CID lock or some odd hardware problem.
I'm truly perplexed by the issue you're having..sure wish I knew how to help ya.
Thanks for the replies. My phone was already unlocked as it was purchased that way. I actually did get custom 2.17 tmo Rom to work, I just hadnt posted here yet. After flashing to the older rom, I flashed to the 2.16 Rom on clubimate.com. Then I had a working 2.16 with GSM. I figured what the hey and went ahead and tried the custom 2.17 Rom again. All is great, and FAST. I wish I could remember what custom Rom I was using before I think it must be the culprit. I cant remember, but it did have the extended rom free and open, total commander, and an unlocker.
Thanks
pterodyne said:
Thanks for the replies. My phone was already unlocked as it was purchased that way. I actually did get custom 2.17 tmo Rom to work, I just hadnt posted here yet. After flashing to the older rom, I flashed to the 2.16 Rom on clubimate.com. Then I had a working 2.16 with GSM. I figured what the hey and went ahead and tried the custom 2.17 Rom again. All is great, and FAST. I wish I could remember what custom Rom I was using before I think it must be the culprit. I cant remember, but it did have the extended rom free and open, total commander, and an unlocker.
Thanks
Click to expand...
Click to collapse
My device is a QTEK 9100. I was upgrading from the ROM on my device when I got it:
ROM 1.1.7.5 9/22/2005
Radio: 01.01.10
Protocol: 4.0.13.16
ExtROM: 1.1.7.105
My carrier is TMobile, so I figured the TMobile custom rom that was built off of the latest QTEK would be a good bet for me - but instead I ended up with no Radio.
I have the IMATE ROM you refer to - maybe I'll try to go to that as an interim step to get to the QTEK ROM I really want, since you had success with that method.
What I don't understand is why the Vanilla QTEK 2.17 (which is what I tried after the TMO Custom 2.17) gave me problems. I don't recall the exact error message, but basically it said it couldn't use that ROM on my device.
pterodyne said:
Thanks for the replies. My phone was already unlocked as it was purchased that way. I actually did get custom 2.17 tmo Rom to work, I just hadnt posted here yet. After flashing to the older rom, I flashed to the 2.16 Rom on clubimate.com. Then I had a working 2.16 with GSM. I figured what the hey and went ahead and tried the custom 2.17 Rom again. All is great, and FAST. I wish I could remember what custom Rom I was using before I think it must be the culprit. I cant remember, but it did have the extended rom free and open, total commander, and an unlocker.
Thanks
Click to expand...
Click to collapse
When you say it was already unlocked, don't you mean SIM unlocked? It would be unusual to buy a phone that is already CID unlocked.
I bought the unbranded k-jam from Simoncells.com. All I did was put my tmobile sim card in it and it worked. I guess I dont know the difference between SIM and CID unlocking.
Well theb that's where you went wrong, sim unlock refers to ur phone being able to use any world sim card...cid unlock refers to country Identification...if ur fone is not cid unlocked then wen u install foreign roms it will bugg up ur fone...dats wat happened to u and that other fellow pterodyne...I sim and cid unlocked my fone. ran the tmo 2.17 custom rom without a problem....plz do ur research on upgrading roms b4 u bash them...most factory fones don't come cid unlocked so I'd b surprised if urs did (tho it prolly came sim unlocked)...

Stuck At 28%

I know there are others experiencing the 28% death wall while trying to flash WM6, but there doent seem to be any specific solutions to this.
I have a Dopod D810 and has already installed 1.30 olipro. Just trying to flash to the official WM6 ANZ Rom. No luck.
Any suggestions guys?
Should just be a very straight forward procedure. Flashing a Dopod with an official Rom.
should be, but it's not... mine is Dopod asia, and stuck at 28% when flashing. Not too sure, but really seemed to me that it was something related to hard-spl. After the 28% error, i reflashed an unofficial rom and tried the official again.
eventually it worked for me.
i guess you don't technically need to manually enter hard-spl first before flashing official ROM.. if anything went wrong i guess you could send it back to them..
safest is to use a modified RUU so it just flashes ROM without IPL + SPL.. i thiiiiiink problem is something to do with SPL
which unofficial rom did u reflash it to? I've been going back and forth with AX3L_OS v3.0.0.2 and the official ANZ dopod rom.
tried about 5 times now. still trying. each time it fails at 28% it's another 10 minutes to flash backto the unofficial rom.
maybe if i try to trce ur steps exactly it might work.
i was flashing to some pdaviet ROM, but i don't think that would make any difference from ax3l's...
have you tried flashing the official ROM with a modified RUU, or you really want the whole package...
If you're just trying to keep everything official i guess you could try to flash the official rom without manually entering bootloader and take your chances. Being that its an official ROM i guess it's safer, or at least covered in warranty..
One question, why don't you try to flash to official WM5 ROM, then to official WM6.. since technically it's supposed to work that way
seriously, i'm not sure why you'd want the official one though.. it's nothing special
Yeah I've tried flashing back to the official WM5 and then WM6, same story.
Tho I havent tried flashing the official WM6 through modified RUU, mainly coz i dont know how to.
Also, In the AX3L version of WM6, there doesnt seem to be a phonepad input method. only keyboard and block recongniser and one other one. Is that coz it's a modified rom, or does WM6 not have the phone pad input. if that's the case i can forget about flashing to WM6 all together.
can't remember if official wm6 has phonepad, but you can just install a cab for it, so it's not a big deal.
look on my site for a link to modified RUU official ROM... instructions are here
i had a lot of problems being stuck at 28%
what eventually i got it to flash to the aus rom was i used SPL 1.20 then it seemed to flash fine.
for some reason my phone doesnt like any other version of SPL besides the one on the latest aus rom either, i flashed to a cooked rom and couldnt flash back until i had put spl 1.20 back in then flashed back to the aus rom.
I have the same problem with 28% stucking
I try to reflash but I still have the same
do you have hard-spl? if so, which version? If you do, flash back a cooked ROM..
if not, you need to try to flash official ROM..
if neither is working, use splxploit. I think all links you need are in this thread already
I have a same problem.
I was upgraded from WM5 to Hong Kong Official WM6 chinese ROM, then I want to change to Official English ROM, I did the Hard-SPL 1.3 and get the SuperCID, but when upgrading the WM6 English officeial ROM, this was stuck at 28%.
Now I was able to flash back to WM5 rom, but I world like to Upgrade to WM6 official ROM, anyone help?
I had this problem when upgrading to the Australian WM6 official HTC Release. The way around it is to run the Trinity Service Provider & CID unlock program from the link below. Dont know why but to use either release, Dopod or HTC WM6 you must run this tool first.
ftp://xda:[email protected]/Trinity/Tools_and_Programs/HTC_Trinity_SIM_CID_Unlock_v1.zip
Hope this helps
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
HI, Thank for your reply, how can I do the modified RUU?
Hi all,
I have success to flash the WM6 official ROM.
this is my experience:
To flash the Radio ROM first, I has flash the 1.50.08.11 Radio ROM.
Then to download the Dutty NBH Tool to take off the Radio DOM of WM6 official ROM.
Then to flash the modify ROM.
Now, my phone is running WM6.
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
Learn something new everyday. Never knew that simply modifying the RUU would itself allow the updates. Just tried it, and yes it works also.
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
how do mofify the RUU? and what do I modify it to?
thanx walterjm
Can you share HK-CHT rom for noSPL noIPL noRadio ? Thanks!
WildsideUK said:
I had this problem when upgrading to the Australian WM6 official HTC Release. The way around it is to run the Trinity Service Provider & CID unlock program from the link below. Dont know why but to use either release, Dopod or HTC WM6 you must run this tool first.
ftp://xda:[email protected]/Trinity/Tools_and_Programs/HTC_Trinity_SIM_CID_Unlock_v1.zip
Hope this helps
Click to expand...
Click to collapse
Can you share HK-CHT rom for noSPL noIPL noRadio ? Thanks!
I had the same problem and I resolve it by extract the rom and re-build it ... look at the thread http://forum.xda-developers.com/showthread.php?t=327667
Good luck

HTC HD radio not turn on to acess network plz help me

hi,
i got oner htc hd i hard spl it and the upgrade it to windows 6.5 all was working fine but it hangs a lot the i flashed it with windows 6.1 rom then the problem came was that all is working fine but i am unable to turn phone on to acess network on phone then i updated it ti the same rom i firstly used the problem was same then i update its radio then also problem was not solved then i update it other 6.5 rom but the problem is same phone doesnt turn on so that i cant acess network plz help me its very urgent for me
Are you sure the hspl update was successful? What spl version is currently showing on your device?
yes hspl was successful
manbir said:
yes hspl was successful
Click to expand...
Click to collapse
What spl is showing?
manbir said:
hi,
i got oner htc hd i hard spl it and the upgrade it to windows 6.5 all was working fine but it hangs a lot the i flashed it with windows 6.1 rom then the problem came was that all is working fine but i am unable to turn phone on to acess network on phone then i updated it ti the same rom i firstly used the problem was same then i update its radio then also problem was not solved then i update it other 6.5 rom but the problem is same phone doesnt turn on so that i cant acess network plz help me its very urgent for me
Click to expand...
Click to collapse
Perhaps you could give a bit more information about your issue. Interesting would be:
do you get the window to enter your pin?
and do you get any error message?
Matthes42 said:
Perhaps you could give a bit more information about your issue. Interesting would be:
do you get the window to enter your pin?
and do you get any error message?
Click to expand...
Click to collapse
i dont get any error and it is also not asking for any pin
its hspl is 1.56 olinex
Ok, so you have the right spl, so that is not the problem. To understand you, you say that you can not activate the phone? Does the phone stay in flight mode? If you go to Settings (Manila tab)\Wireless Controls and turn the Phone slider on, does it turn itself off again?
You can try to run the setup again. Go to Start\Settings (All Settings)\Connections\Connection Setup and make sure your Country and Operator are correct and press Ok to setup.
ClydeB1 said:
Ok, so you have the right spl, so that is not the problem. To understand you, you say that you can not activate the phone? Does the phone stay in flight mode? If you go to Settings (Manila tab)\Wireless Controls and turn the Phone slider on, does it turn itself off again?
You can try to run the setup again. Go to Start\Settings (All Settings)\Connections\Connection Setup and make sure your Country and Operator are correct and press Ok to setup.
Click to expand...
Click to collapse
am unable to turn the phone on rest all settings of country operator also ok
Is your device perhaps not SIM locked? What rom did you have originally? Have you tried to reflash to that original version and see if the problem is resolved.
When you first flashed to the 6.5 rom did the phone work then? I know you say you had lots of freezes, but before that did the phone work on the 6.5 rom?
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
miniterror said:
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
Click to expand...
Click to collapse
yes i flashed back to 6.1 but phone is not provide locked its phone is not turning on and i have cheked that all sims were working fine
miniterror said:
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
Click to expand...
Click to collapse
manbir said:
yes i flashed back to 6.1 but phone is not provide locked its phone is not turning on and i have cheked that all sims were working fine
Click to expand...
Click to collapse
Thanks I saw that you did try a 6.1 rom, but I was asking if you tried the initial original 6.1 rom. You may have tried another 6.1 rom but not the original rom that was on the phone before you started flashing.
To my other questions then, did the phone initially work when you first flashed to the 6.5 rom? If after all of this and it was initially working on the 6.5 rom, you may have a hardware problem and may need to flash back to the original rom and take it back to HTC for a service.
ClydeB1 said:
Thanks I saw that you did try a 6.1 rom, but I was asking if you tried the initial original 6.1 rom. You may have tried another 6.1 rom but not the original rom that was on the phone before you started flashing.
To my other questions then, did the phone initially work when you first flashed to the 6.5 rom? If after all of this and it was initially working on the 6.5 rom, you may have a hardware problem and may need to flash back to the original rom and take it back to HTC for a service.
Click to expand...
Click to collapse
yes the phone was working fine when i firstly flashed to 6.5 rom and its not hardware how can i know which was original rom now at this condition???
manbir said:
yes the phone was working fine when i firstly flashed to 6.5 rom and its not hardware how can i know which was original rom now at this condition???
Click to expand...
Click to collapse
You can try going to the HTC website for your county and look to see if there is a rom upgrade available. If so you can enter your Serial Number to see if you can access it for download. Alternatively you can look for a stock rom here Try and find a friend near you with the HD and check their version.
Same problem here .....my wifi cant connect to anything..when im tryin to turn it on nothings happen and cant acces to web browsing..nothing works...i have flahed 4 roms till now and all the rom had the same problem...i ve flashed miris rom NRG rom Dutty rom and maryone....i dont know what to do....till before a week worked like a charm...but now it is still dead....
If your wi-fi was working and then on the same rom has suddenly stopped working that probably sounds like a hardware issue. You may need to flash back to rom and return the device for a service.
are you serious??cause in my country i leave in greece salonica..and the htc center is in athens and must send the device there and they told me to wait about one month or two to get it back....no way...!!!!but it is very strange...when i had miris rom it worked like a charm..after trying to flash a new rom to nrg then wifi stopped workin...tryed to flash another rom like duttys and maryone and still the same....why am i so unlucky???is there any solution???maybe is that any problem with rom?or misiing some file?
anyway thanks for reply....have a nice and a happy new year...god bless you!!
pm...sorry for my english...
edangel said:
are you serious??cause in my country i leave in greece salonica..and the htc center is in athens and must send the device there and they told me to wait about one month or two to get it back....no way...!!!!but it is very strange...when i had miris rom it worked like a charm..after trying to flash a new rom to nrg then wifi stopped workin...tryed to flash another rom like duttys and maryone and still the same....why am i so unlucky???is there any solution???maybe is that any problem with rom?or misiing some file?
anyway thanks for reply....have a nice and a happy new year...god bless you!!
pm...sorry for my english...
Click to expand...
Click to collapse
You can always try going back to the miri rom you were using, or to the original rom that was on the phone. If wi-fi still does not work then it sounds like it is a hardware issue and there is no other way around it that I can see but to take it in for a service, unless you think you can replace the part yourself. Is there no cell phone repair services in your location, although you may need to pay to have it repaired then as it will not be under HTC warranty then if you are prepared to take that chance. Sometimes these parts just break, it doesn't happen all the time, but hey even multi-million $ F1 cars break down.
ClydeB1 said:
You can always try going back to the miri rom you were using, or to the original rom that was on the phone. If wi-fi still does not work then it sounds like it is a hardware issue and there is no other way around it that I can see but to take it in for a service, unless you think you can replace the part yourself. Is there no cell phone repair services in your location, although you may need to pay to have it repaired then as it will not be under HTC warranty then if you are prepared to take that chance. Sometimes these parts just break, it doesn't happen all the time, but hey even multi-million $ F1 cars break down.
Click to expand...
Click to collapse
SO...FOR MANY HOURS TO FIND SOMETHING I MADE IT...THE SOLUTION IS UNDER START SETTINGS CONNECTION ADVANCED NETWORK AND THEN I JUST ENABLE FROM HSDPA/HSUPA TO ONLY HSDPA AND NOW ITS WORKING...
AS I THOUGHT THIS SETTINGS DEPENDS OF WHAT MODEM ROUTER YOU HAVE...JUST WORKING FINE NOW.....
SO EVEN MULTI MILLION F1 CAN BE FIXED UP......if you are rich and got the money...hahahaha
SO THANKS ANYWAY!!!!!!!!I AM GLAD FOR TRYING TO HELP ME.....
edangel said:
SO...FOR MANY HOURS TO FIND SOMETHING I MADE IT...THE SOLUTION IS UNDER START SETTINGS CONNECTION ADVANCED NETWORK AND THEN I JUST ENABLE FROM HSDPA/HSUPA TO ONLY HSDPA AND NOW ITS WORKING...
AS I THOUGHT THIS SETTINGS DEPENDS OF WHAT MODEM ROUTER YOU HAVE...JUST WORKING FINE NOW.....
SO EVEN MULTI MILLION F1 CAN BE FIXED UP......if you are rich and got the money...hahahaha
SO THANKS ANYWAY!!!!!!!!I AM GLAD FOR TRYING TO HELP ME.....
Click to expand...
Click to collapse
Hey, I'm glad you got it sorted. I'll remember to add that additional check to my little arsenal of things for troubleshooting. Thanks for the feedback.

What the hell nothing works

Bought an HD, flashed HSPL, flashed Dutty R14, hard reset twice. Everything works perfectly except phone freezes every time I try to answer an incoming call. So I flashed 3 other roms and had the same problem with all of them. Then I flashed the stock Telstra rom and it works perfectly, I can answer calls and everything is fine.
I thought it was a problem with my phone so I bought a brand new HD and flashed the HSPL then the R14 rom and I have the same problem where I can't answer calls. There's no way it's a problem with the phone itself since it's brand new and I've had this problem on 2 separate phones. It's also hard to believe that every single rom here has a problem where you can't answer calls, or that R14 is so bad that it screws up something internally as soon as you install it.
What's going on?
This same thing happened to me - had to get a new SIM card from my cell phone provider. Some older SIM cards cause this - not sure why?
rpimps said:
Bought an HD, flashed HSPL, flashed Dutty R14, hard reset twice. Everything works perfectly except phone freezes every time I try to answer an incoming call. So I flashed 3 other roms and had the same problem with all of them. Then I flashed the stock Telstra rom and it works perfectly, I can answer calls and everything is fine.
I thought it was a problem with my phone so I bought a brand new HD and flashed the HSPL then the R14 rom and I have the same problem where I can't answer calls. There's no way it's a problem with the phone itself since it's brand new and I've had this problem on 2 separate phones. It's also hard to believe that every single rom here has a problem where you can't answer calls, or that R14 is so bad that it screws up something internally as soon as you install it.
What's going on?
Click to expand...
Click to collapse
You got to be kidding. If it works perfect with stock rom, your phone is good in quality.
You should try updating the Radio as well.
bdbell said:
This same thing happened to me - had to get a new SIM card from my cell phone provider. Some older SIM cards cause this - not sure why?
Click to expand...
Click to collapse
Yeah my card is at least a few years old (still says Cingular instead of AT&T) so I'll try getting a new one and see if it works.
mcdull said:
You got to be kidding. If it works perfect with stock rom, your phone is good in quality.
You should try updating the Radio as well.
Click to expand...
Click to collapse
What radio would you suggest? 1.14.25.24 is supposed to be the best one for my area (inner-city Houston/Austin, TX in the US) and that's what I've been using. It's the same one that comes with the stock rom that worked.
rpimps, I'm a bit north of you in OK, and 1.13.25.24 is what I've used for some time with great batt life and reception and got the same while in Houston not long ago.
I've got the Telstra, but the stock rom I flash before cooked is always the European 1.56, which I downloaded from the HTC Europe website. It comes with 1.13.
bdbell said:
This same thing happened to me - had to get a new SIM card from my cell phone provider. Some older SIM cards cause this - not sure why?
Click to expand...
Click to collapse
I got a new sim and it still does it. Also I'm using the same radio that I used with the stock rom, and the stock rom worked fine, so I doubt the radio is the problem. I think the HD just isn't capable of running these roms.
Is your model a BLAC100?
Also, what language did you use?
Could it be the problem of non-English characters?
mcdull said:
Is your model a BLAC100?
Also, what language did you use?
Could it be the problem of non-English characters?
Click to expand...
Click to collapse
How do you check if it's a BLAC100? All I know is it's an 8285. The only language I use is English.
Why don't you try another rom, there's a lot of rom's here.
rpimps said:
Then I flashed the stock Telstra rom and it works perfectly, I can answer calls and everything is fine.
Click to expand...
Click to collapse
So hardware of your HD is OK. Nothing wrong with device.
As Sean3 wrote, try to flash WM 6.1 European 1.56, links are on HD Wiki...
If it works too, then it's some conflict between cooked ROMs and your device.
Bodisson said:
So hardware of your HD is OK. Nothing wrong with device.
As Sean3 wrote, try to flash WM 6.1 European 1.56, links are on HD Wiki...
If it works too, then it's some conflict between cooked ROMs and your device.
Click to expand...
Click to collapse
It works fine with the stock rom, but it doesn't work with ANY other rom. That's what's so weird.
Totally wild question: Are you sure you have UNLOCKED device?
Altough, I have no idea does that matter at all...
Just 2 throw in my 2 cents and a quick recap:
1. You flashed HSPL - Was this successful? What is your SPL? Did you use correct HSPL? Did you follow this guide?
2. You then flashed rom and everything worked but phone freezed everytime you tried to answer a call - Have you tried another radio?
3. There is no reason why your device wouldn't be able to use cooked roms if you have successfully unlocked it by using either USPL or HSPL
4. You say you have returned to stock rom - Did you return to original stock rom, i.e. rom which was on your device when you got it. Did you also return to stock SPL? Was this 100% successful?
Bodisson said:
Totally wild question: Are you sure you have UNLOCKED device?
Altough, I have no idea does that matter at all...
Click to expand...
Click to collapse
Yes it's unlocked. It does answer calls SOMETIMES and it always makes outgoing calls successfully.
Fallen Spartan said:
Just 2 throw in my 2 cents and a quick recap:
1. You flashed HSPL - Was this successful? What is your SPL? Did you use correct HSPL? Did you follow this guide?
2. You then flashed rom and everything worked but phone freezed everytime you tried to answer a call - Have you tried another radio?
3. There is no reason why your device wouldn't be able to use cooked roms if you have successfully unlocked it by using either USPL or HSPL
4. You say you have returned to stock rom - Did you return to original stock rom, i.e. rom which was on your device when you got it. Did you also return to stock SPL? Was this 100% successful?
Click to expand...
Click to collapse
1. HSPL flash was successful, I used this guide - http://forum.xda-developers.com/showpost.php?p=3930436&postcount=2 - and flashed it to 1.56 olinex.
2. I tried 2 radios, 1.14 and 1.17.
3. I flashed the stock Telstra rom but kept the 1.56 olinex SPL. Was successful, and phone works perfectly with this rom. I also tried another wm6.1 rom (dutty 3.9xt) to see if there was a problem with it running 6.5 but the 6.1 rom had the same problem.
Is your device not SIM locked? Can you insert another SIM into the device, try one of your mates SIMs
ClydeB1 said:
Is your device not SIM locked? Can you insert another SIM into the device, try one of your mates SIMs
Click to expand...
Click to collapse
Tried that, it has the same problem, outgoing calls are fine but incoming calls freeze sometimes.
The device is an unlocked Telstra and I'm using it with AT&T in the US.

Radio problemwith HD2-TmoUSA

Hi
I have a strange problem with my HD2.
I am only able to dial certain phone nos.Some phone nos.- when you press "call" key, just make a "tu tu" sound & I get back dial pad.
However using the same SIM card, I can dial the same no.from another Nokia phone.
Pl advise :-
1.How to solve this problem?
2. If I have to upgrade my ROM (Win 6.5), what ROM I should upgrde to? I am in India now & won't use HD2 in USA.
3.What Android or Win7 can I upgrade to - if above upgrade doesn't work?
4.How Can I get my Stock ROm for HD2 to revert back to original state, if something goes wrong
Pl advise as I am new to Win phones but good with RIM phones
Thanks in adv
Hi
I have now upgraded my phone ROM with T-Mobile update. A new radio isinstalled and the phone seems to be working well.Am able to dialnos which werenot working earlier
clive48 said:
Hi
I have now upgraded my phone ROM with T-Mobile update. A new radio isinstalled and the phone seems to be working well.Am able to dialnos which werenot working earlier
Click to expand...
Click to collapse
Glade to see you were abale to resolve your own problem kudoes to you for being able to search unlike some. But just as a friendly reminder don't forget to upsate your ROM and Radio in your signature. lol
is it ok to flash Leo_RADIO_2.15.50.14** into TMOUS?
zelduy said:
is it ok to flash Leo_RADIO_2.15.50.14** into TMOUS?
Click to expand...
Click to collapse
Yes that is ok to flash to a TMOUS. You just can not flash a radio version that looks like 2.04.50.xx, 2.05.50.xx, or any x.xx.51.xx as they will brick a TMOUS HD2. Also never ever flash a official ROM from anywhere besides T-Mobile as they may contain a one of these radio versions.

Categories

Resources