Related
Using USB I don't have a problem, however when I try to setup ActiveSync using bluetooth I can not get it to work.
When connecting my PC to the Phone using add new connection wizard I get the following message after the Laptop finds the phone and I enter in the security code: "Installing a modem on COM40"
Well when I then connect my phone to the Laptop there is not a COM40 to pair up to.
I'm using:
Windows XP sp2
Bluetooth Stack for Windows by Toshiba v4.31.02.6(d)
Microsoft ActiveSync 4.5
Tilt with latest htc rom v1.62.502.0
Any advice or suggestions would be appreciated.
Activesync Bluetooth
1) delete all bluetooth pairings between phone and computer.
2) go into your pc bluetooth settings (varies between BT manufacturer, but try right clicking the taskbar logo and selecting properties)
3) find the com port number used for serial port (remember)
4) open windows mobile device center on your pc
5) (without having your ppc connected) hover over <mobile device settings. and select <connection settings> from the drop-down menu.
6) tick the ,allow connections to one of the following. box and select click the comport number you discovered in point 3 above.
7) attempt to repair via your pc using the software bundled with your BT (or via control panel if inbuilt)
8) during pairing the connection type options will now list <activesync> instead of <serial port>, tivk this box and save.
9) launch activesync on your ppc (from <programs>) and select <menu>, <connect via bluetooth>
eakeyson said:
Activesync Bluetooth
1) delete all bluetooth pairings between phone and computer.
2) go into your pc bluetooth settings (varies between BT manufacturer, but try right clicking the taskbar logo and selecting properties)
3) find the com port number used for serial port (remember)
4) open windows mobile device center on your pc
5) (without having your ppc connected) hover over <mobile device settings. and select <connection settings> from the drop-down menu.
6) tick the ,allow connections to one of the following. box and select click the comport number you discovered in point 3 above.
7) attempt to repair via your pc using the software bundled with your BT (or via control panel if inbuilt)
8) during pairing the connection type options will now list <activesync> instead of <serial port>, tivk this box and save.
9) launch activesync on your ppc (from <programs>) and select <menu>, <connect via bluetooth>
Click to expand...
Click to collapse
I just want to say that FINALLY I GOT IT WORKING!!!!!! on my Touch Elf. this advice worked perfectly. It took me some time to find it but this was the answer that I was looking for. I was almost ready to give up and start a new thread to ask for help with this problem (I havn't ever had to yet) and now I don't need to. Persistance in searching pays off
This didn't work for me.
I have a Dell D830 with a Toshiba Bluetooth chipset.
Any help?
I have the same problem with Dell D630 (Toshiba BT). I can't choose any COM Ports, it just automatically selects COM40 - which you cant use with Activesync 4.5 (port range 1-20).
Any help for this?
This didn't work for me, but I found something that did
Okay,
I'm using XP on my Dell D830 with the latest BT drivers (Toshiba BT w/ Dell's R167661 - Bluetooth drivers) and an AT&T Tilt.
I've hacked together information from several sources that I can no longer even remember, but since this was at the top of a google search for ActiveSync D830 Bluetooth "Serial Port" I thought that I would post my success here.
Make sure that you've removed any pairings from previous attempts and try this:
- On your Windows Mobile device, go to Settings/Connections/Bluetooth/Mode and check the box for "Make this device visible to other devices" and press OK.
- Back to the PC: Double click on the Bluetooth icon in the System Tray (if it's red then you have Bluetooth disabled somehow - try pulling the slider on the left side of the D830 toward you). This will take you to the Bluetooth Settings.
- Click on "New Connection"
- On the next pane leave "Express Mode" selected and click Next. After a moment you should see your Windows Mobile Device.
- Click Next.
- A dialog to enter a Bluetooth Passkey (PIN) will show. You will need to remember this passkey for a later step. Press OK.
- A dialog will pop up on you Windows Mobile device stating that some device is trying to connect. Press "Yes".
- After that a dialog will pop up to enter a passkey. Enter the same passkey that you used in the previous step and press Next.
- Now ActiveSync should be selected in the list of services detected. Press Save.
- On your laptop you should be setting at the Advanced Modem Page. Click Next.
- Not sure what this page is for, but I put just a one ("1") in the Telephone number field and pressed Finish.
If all of that worked, then on your Windows Mobile device go to ActiveSync, select menu, and Connect via Bluetooth.
I have successfully performed these steps about 6 times in the course of this write up. I am not any kind of ActiveSync expert so I most likely won't be able to answer questions like "why wasn't my device listed in the Bluetooth settings".
Hope this helps and good luck,
-Jim Roberts
Doesn't Work!
I tried the steps you suggested, but after pairing, the Toshiba utility automatically creates Port 40 then enters the Dial-Up Connection wizard. The mobile device does not let me choose ActiveSync (only "Serial Port" and "Wireless Stereo" are available).
I'd like to say thank you very much from Australia for the above mentioned instructions. If follwed exactly, they work fine with Blueant bluetooth dongle using windows xp and bluetooth stacks. I too have the problem of no more activesync via usb cable and the above has saved me from throwing the phone
Thanks again
Frank
I've spent several hours attempting to get this working, I've even bought two new BT dongles for my computer for testing.
Is it at all possible to get activesync working over BT on the diamond? Can't seem to get the ActiveSync profile offered... Neither on my PC or my phone!
audiophil said:
I've spent several hours attempting to get this working, I've even bought two new BT dongles for my computer for testing.
Is it at all possible to get activesync working over BT on the diamond? Can't seem to get the ActiveSync profile offered... Neither on my PC or my phone!
Click to expand...
Click to collapse
Same happend to me until I found the right settings after that I just get irritated when my cable connection doesn't work, in other words I just use it whitout even nowing what the settings are, maybey I can help you if you tel me your settings and show some screendumps, after that I can show you some screendumps whit a working bluetooth connection.
Ps I am not giving any garanty just want to keep my own bluetooth connection
Willem
It works fine for me with Mobile Device Center. Remember to enable BT connection on desktop Activesync options, or else the profile won't appear when you pair with the phone.
I've never got BT/AS to work either (and I've spent days trying), as you say, I never get offered the AS service.
I did see it *once* on the Diamond when I was trying to connect another service (maybe Obex) but I didn't realise how important that was at the time.
I'm using XP/SP2 with the Toshiba stack but I've tried the BlueSoleil stack also with the same result.
I'm guessing this is a problem with the Diamond as I can happily connect with my Artemis via BT to the same laptop
Mee too, I saw the AS-service ONCE, but never ever again.. .:'( Tried 3 dongles and probably 6 different stack implementations.
I'm using XP as well, are the only success stories related to Vista?
Never seen it.
A bad-developed thing with MS and activesync, too bad.
I don't now how your guys try to connect I just can tell how my connection works flawless.
First of all and most important problem whit me was that I have to use the phone to make the connection and not the pc/notebook offcourse you have to allow active sync to acces your phone, in my case this is is found at file connection and allow conection for a compoort in my case com7, then I switch bluetooth on at my phone (and not try to sync straight away cause this results often in a faillure ) and then connect true bluetooth at my phone using the comand connect true bluetooth at active sync at my phone.
One of the strange things which have to set is "All connections use this connection and there is selected "USB" this maid seems trange but I believe the compoort is a virtual one which is used to connect at USB for that reason you have to add a compoort before making your connection, if done right your Diamond will ask for it as soon as you setup the bluetooth connection, the last thing can be wrong cause I don't remember quite well how I did the setup of that part, just because I never use any other connection anymore seems I mannaged to get it working.
This way I can even use it as a wireless webcam which can make you do funny things, the danger of it is when some good programmer makes a virus which allow to setup that connection remotley, aswell the connection whit pocketcontroller I don't want to think off what would hapen if someone manage to get controll of my phone.
Don't now or this is helpfull if any questions feel free.
Willem
On my diamond the only service I can find on my laptop is:
Serial Port
Wireless Stereo
AS set to use the same port as the incoming port in my bluetooth manager...
If you set COM ports right, you tie Diamond with PC using Diamond's ActiveSync. Start/Programs/ActiveSync, the Menu|Connect via Bluetooth. It should ask you now to make a new connection. Tap yes, it will search for BT devices. Choose your PC. If you did everything all right, now you will be connected.
(this may be obvious but I had some problems at start; I thought you initiate the connection on PC)
kosherpig said:
(this may be obvious but I had some problems at start; I thought you initiate the connection on PC)
Click to expand...
Click to collapse
Yes... But what to do when this fails? Anyone ever encountered the "no activesync profile" problem and actually solved it?
audiophil said:
Yes... But what to do when this fails? Anyone ever encountered the "no activesync profile" problem and actually solved it?
Click to expand...
Click to collapse
I gues if there is no active sync profile yet you have to create one what maid be possible aswell is that your settings under active sync/options at your phone where you must selct the options which you want to be syncted, if nothing is selected there it will make a connection but will not sync.
This worked for me
To Async using MICROSOFT Stack do the following:
a. open Control Panel and open Bluetooth Devices
b. click Add and add your device. go to Options and mark "Allow Bluetooth devices to find this computer" and "Allow Bluetooth Devices to connec to this computer". you can also mark other options as desired.
c. go to COM ports and add an INCOMING port. it will choose a port for you automatically.
d. go to WMDC/Connection Settings and mark "Allow connections to one of the following.." and choose the port you created.
e. go back to Devices and choose your PDA. choose Properties and go to Services. there you should see all services your PDA provides. one of them should be Active Sync Bluetooth Service. mark it and click OK. your comp and PDA should connect and disconnect a few secs later.
f. on your device, open ActiveSync and under Menu choose Connect Via Bluetooth.
I just provide my solution.
I use IVT BlueSoleil to manage my BT dongle. After installed, the BT dongle could be recognized as a COM port on the PC. Check through the PC device manager to know what the port number is, then adapt in Activesync, select "Allow connections to one of the following", select COM7 in my case.
Enable BT on the Diamond to make it visible to PC, after paring the PC with Diamond, Diamond could recognize the PC provides ActiveSync services.
Go to Diamond's ActiveSync, select connect via BT, PC will automatically accept the connection from Diamond.
P.S I am not a native English speaker, I just wonder if I could make you understood.
netmaomao said:
I just provide my solution.
I use IVT BlueSoleil to manage my BT dongle. After installed, the BT dongle could be recognized as a COM port on the PC. Check through the PC device manager to know what the port number is, then adapt in Activesync, select "Allow connections to one of the following", select COM7 in my case.
Enable BT on the Diamond to make it visible to PC, after paring the PC with Diamond, Diamond could recognize the PC provides ActiveSync services.
Go to Diamond's ActiveSync, select connect via BT, PC will automatically accept the connection from Diamond.
P.S I am not a native English speaker, I just wonder if I could make you understood.
Click to expand...
Click to collapse
I think the majority here isn't a native English speaker, this forum isn't a forum about language but about phones and pda's if someone wants to show how good his/here English is they beter look for another forum.
I think this forum is one of a few where the solution which someone offers weights more then the way its sad, unless its offending.
Untill now (I don't now what I am calling over myself now) I never got any critics at my English which is far from perfect the last thing wasn't nescesary to say even a blindone could see it whitout braille.
hays said:
This worked for me
To Async using MICROSOFT Stack do the following:
a. open Control Panel and open Bluetooth Devices
b. click Add and add your device. go to Options and mark "Allow Bluetooth devices to find this computer" and "Allow Bluetooth Devices to connec to this computer". you can also mark other options as desired.
c. go to COM ports and add an INCOMING port. it will choose a port for you automatically.
d. go to WMDC/Connection Settings and mark "Allow connections to one of the following.." and choose the port you created.
e. go back to Devices and choose your PDA. choose Properties and go to Services. there you should see all services your PDA provides. one of them should be Active Sync Bluetooth Service. mark it and click OK. your comp and PDA should connect and disconnect a few secs later.
f. on your device, open ActiveSync and under Menu choose Connect Via Bluetooth.
Click to expand...
Click to collapse
Worked flawlessly for me as well. Thanks.
hays said:
This worked for me
To Async using MICROSOFT Stack do the following:
a. open Control Panel and open Bluetooth Devices
b. click Add and add your device. go to Options and mark "Allow Bluetooth devices to find this computer" and "Allow Bluetooth Devices to connec to this computer". you can also mark other options as desired.
c. go to COM ports and add an INCOMING port. it will choose a port for you automatically.
d. go to WMDC/Connection Settings and mark "Allow connections to one of the following.." and choose the port you created.
e. go back to Devices and choose your PDA. choose Properties and go to Services. there you should see all services your PDA provides. one of them should be Active Sync Bluetooth Service. mark it and click OK. your comp and PDA should connect and disconnect a few secs later.
f. on your device, open ActiveSync and under Menu choose Connect Via Bluetooth.
Click to expand...
Click to collapse
I was able to sync my Diamond using WMDC on vista using these steps, with a few modifications.
I had to leave my WMDC "Connections Settings" pull-down box on "Bluetooth" for it to work for me. I'm using a USB dongle, this may be why.
On step (e), after opening the "Services" tab and unchecking, then rechecking the "Active Sync Bluetooth Service" box and hitting Okay, my device would be listed as "Connected" on the main Devices tab for a few seconds before disconnecting (about 3 seconds). I had to initiate step 4 BEFORE the device disconnected. So basically I had 3 seconds to start the Bluetooth sync to get them talking. Haven't had any problems since!
-Mike
This is what worked for me, when not able to get the active sync profile.
In settings for "USB to PC";
turned off 'enable advanced network functionality'
My PC and my Diamond didnt show me any services. Because of that it says no device is paired when i want to connect, although my PC is paired.
I use XP SP3 and the Windows BT Stack.
xp SP3 is a problem ?
cuz nothing work for me
Doesn't work for me either.
Using Vista64SP2.
It worked before but eventually stopped working now.
I see ActiveSync on the Phone and on the Notebook.
AS tries to establish a connection for some seconds but cant do it.
//edit:
Ooook, after Firmware-Flash of new o2 Germany v2.03.207.2 everything's working again. *strange*
Sorry I really need to ask. I have been trying in vain to bluetooth files from my laptop to my X1 (R3AA). As of now, my phone can send (or beam) files via bluetooth to my laptop, but not receive anything at all.
Unlike my P1i, the Bluetooth services available for the X1 (showing up on my laptop) does not include the "file transfer service" that was used for exploring the phone's memory stick via bluetooth a la all the other six older Sony ericsson phones that I've previously owned...
I've already:
(i) Checked the allowing incoming beams box in "settings"
(ii) Installed Obex Inbox (but I think that simply is to allow incoming bluetooth beams to get stored in your storage card instead of device)
Is there anything else I haven't done? I right click on my laptop the file after pairing with my X1 and when I hit "send via bluetooth", basically nothing happens. Man, even my old t610i didn't have problems with bluetooth receiving...
it works for me bro.
start > settings > bt > mode > check both boxes! > ok
this will make X1 "visible" for your laptop.
BR!
-mattx- said:
Sorry I really need to ask. I have been trying in vain to bluetooth files from my laptop to my X1 (R3AA). As of now, my phone can send (or beam) files via bluetooth to my laptop, but not receive anything at all.
Click to expand...
Click to collapse
Hmmm... my X1 works well too. Do you have a custom ROM? in case, which one?
so, you select the file, send to, X1 and nothing happen on the screen of your laptop? if so, it is a laptop problem, not X1 problem.
If it would have been an X1 problem, you would have seen a progression bar saying "discovering services available on X1" and then disappearing because of your mentioned X1 problem.
I'll be waiting for your answers to help you!
-mattx- said:
Unlike my P1i, the Bluetooth services available for the X1 (showing up on my laptop) does not include the "file transfer service" that was used for exploring the phone's memory stick via bluetooth a la all the other six older Sony ericsson phones that I've previously owned...
Click to expand...
Click to collapse
Not sure about why your bluetooth is not receiving, but you can make your laptop access your memory stick as a normal folder to browse the files.
Follow these steps.
1. Make sure you have activesync installed on your laptop.
2. Go to activesync on your phone and select connect via bluetooth.
This should establish a activesync connection thro bluetooth, similar to what you get thro a USB connection.
bharat4ever said:
Not sure about why your bluetooth is not receiving, but you can make your laptop access your memory stick as a normal folder to browse the files.
Follow these steps.
1. Make sure you have activesync installed on your laptop.
2. Go to activesync on your phone and select connect via bluetooth.
This should establish a activesync connection thro bluetooth, similar to what you get thro a USB connection.
Click to expand...
Click to collapse
Hmm. doesn't work here,
Vista, Windows Mobile Device Center.
Any clue?
hmm, next time you connect your phone thro usb, let it connect completely to windows mobile device center, then go to Mobile device setttings, and click on connection settings.
Make sure the check box "Allow connections from one of the following" is checked, and "Bluetooth" is selected from the list. I hope this works. Fingers crossed.
Hi guys,
Thanks for the replies, which help steer me in the correct direction. It seems Activesync is responsible for "unlocking" the bluetooth functions (I kid you not). Finally solved it. This is how I did it (based on advice given):
1. Checked all boxes in Bluetooth options in settings: visibility/bluetooth on/authentication passkey required
2. X1 was already paired up with my laptop
3. Connected to my laptop via USB and activesync loaded automatically
4. Opened up "My Bluetooth Places", which is the program that comes with installation of the Bluesoleil program on my laptop
5. Heard a beep on my X1 for the first time when I did this (this was the first time I was connected on USB via activesync AND activating bluetooth AND accessing the bluetooth places folder) - I think this was what activated it in the end - sorry if i'm not explaining it too well here, but it did the trick
Note: Not sure if a few more options popped up in "My Bluetooth places" folder I don't recall seeing bluetooth messaging/contacts there previously. My OS is XP home, using the default R3A rom.
6. I could transfer files via bluetooth already from my laptop to X1...
*I still haven't been able to manage to get within the file directory tree using bluetooth, bharat4ever, which program (and bluetooth service) might I ask did you use to do that?*
Additional thingys: I think it's important to use a proper software for bluetooth file transfers - Bluesoleil is much better imo than that standard Widcomm (oldish as well) program that came default with my laptop.
I was also wondering if I could transfer multiple files via bluetooth and seems like resco explorer can do the trick, though folders can't be sent via bluetooth - tho the contents inside them will.
Hi everyone!
I'm wondering how to connect Leo with PC via Bluetooth..Just sometimes I come to Office and forget my cable...poor..
If anyone knows it, please share some experiences for me. Add video or picture it's more clear..
Thanks so much!
noone knows how to do it???
Pair your device with your computer, then connect to it.
You can access the HD2's Bluetooth manager in All Settings/Bluetooth.
To pair, either put your computer in discoverable mode and add it with your HD2, or the other way around.
To put your phone in discoverable mode, tab on the left (Settings) tab in the Bluetooth manager then look for the relevant option.
To put your PC in discoverable mode, look for the Bluetooth icon in the notification area, right click it and select "Open Settings", tick on "Allow discovery by other devices", and click OK.
To pair from the HD2, in the Bluetooth manager's device list (middle tab), tap Menu, tap "Add device", and follow the instructions.
To pair from the PC, look for the Bluetooth icon in the notification area, then right click and select "Add a device".
Once done, tap the "+" near the PC's name in the device list too see the available services, then tap ActiveSync.
The ActiveSync service will not appear if the PC doesn't have ActiveSync or WMDC installed, or if the device already has an ActiveSync connection established (i.e if you are connected by the USB cable)
Successfully did it today ! In office without the microUSB cable but needed to transfer a file (also didn't have a microSD card reader with me).
First pair the PC with HD2 (enabled automatic authentication between the 2 from now on)
Confirmed ActiveSync include COM5 (or whatever in your case Bluetooth is using)
on HD2 side, ActiveSync > Connect
Whoala ! Just like the cable equivalent.
Yunabeco said:
Pair your device with your computer, then connect to it.
You can access the HD2's Bluetooth manager in All Settings/Bluetooth.
To pair, either put your computer in discoverable mode and add it with your HD2, or the other way around.
To put your phone in discoverable mode, tab on the left (Settings) tab in the Bluetooth manager then look for the relevant option.
To put your PC in discoverable mode, look for the Bluetooth icon in the notification area, right click it and select "Open Settings", tick on "Allow discovery by other devices", and click OK.
To pair from the HD2, in the Bluetooth manager's device list (middle tab), tap Menu, tap "Add device", and follow the instructions.
To pair from the PC, look for the Bluetooth icon in the notification area, then right click and select "Add a device".
Once done, tap the "+" near the PC's name in the device list too see the available services, then tap ActiveSync.
The ActiveSync service will not appear if the PC doesn't have ActiveSync or WMDC installed, or if the device already has an ActiveSync connection established (i.e if you are connected by the USB cable)
Click to expand...
Click to collapse
Thanks for your help!
one more question..in this case to sync PC with PPC. Do the PC need a Bluetooth set to connect with PPC? If like that I think my PC can not apply for..I see only Laptop have Bluetooth set included inside..what a pity!
Anyway thanks for your share!
Best Regard!
I can pair my Velocity (Telstra Oz Branding still with stock OS) with a Windows 7 32-Bit pc but it will not connect. During installation (& under Device Manager), I get warning that Windows could not find the driver for "Bluetooth Peripheral Device".
I have no issues with pairing or connecting other devices on either the Velocity or the PC - it's just between the Velocity and the PC. I've just come from the HD2 so I'm a newb with this Handset which was fine.
I can on the PC "send a file" to the phone just fine but no PAN or tethering...or are these features not yet part of Andriod 2.3.7 or is there some setting I don't know about?
Thanks
Nathan
jmone said:
I can pair my Velocity (Telstra Oz Branding still with stock OS) with a Windows 7 32-Bit pc but it will not connect. During installation (& under Device Manager), I get warning that Windows could not find the driver for "Bluetooth Peripheral Device".
I have no issues with pairing or connecting other devices on either the Velocity or the PC - it's just between the Velocity and the PC. I've just come from the HD2 so I'm a newb with this Handset which was fine.
I can on the PC "send a file" to the phone just fine but no PAN or tethering...or are these features not yet part of Andriod 2.3.7 or is there some setting I don't know about?
Thanks
Nathan
Click to expand...
Click to collapse
Had the same issue with mine.
1. Instal HTC Sync
2. Pair set your phone discoverable.
3. Search for bluetooth devices from your PC.
4. Select your phone.
5. After pairing your mobile go to
Start->Devices and Printers right click on your phone name Properties then Services tab, choose only
Advanced Audio - tick if your bluetooth pc is compatible or leave it blank
EMAIL - leave blank
File Transfer (Obex) - tick
Headset Audio Gateway - tick if your bluetooth pc is compatible or leave it blank
Object Push (Obex) - tick
Remotely Controllable Device - tick if your bluetooth pc is compatible or leave it blank
SMS - leave blank.
Then on your PC right click on Bluetooth icon choose Join Area Network and select your phone.
Hope it will help. This resolved my issue.
But just to let you know My HTC Raider is not able to receive *.apk extension over bluetooth. MP3, jpg perfect.
Mmmm looks like my handset is only advertising that it has EMAIL and SMS as "Services" to the PC. Do you know if I need to install anything on the Handset?
Thanks
Nathan
I don't know what PAN is, or maybe I just dont recognize the acronym, but you should use the wireless hotspot for tethering, much, much, much, faster than BT.
FYI - Straight from Wikipedia:
=============
Bluetooth vs. Wi-Fi (IEEE 802.11)
Bluetooth and Wi-Fi (the brand name for products using IEEE 802.11 standards) have some similar applications: setting up networks, printing, or transferring files. Wi-Fi is intended as a replacement for cabling for general local area network access in work areas. This category of applications is sometimes called wireless local area networks (WLAN). Bluetooth was intended for portable equipment and its applications. The category of applications is outlined as the wireless personal area network (WPAN). Bluetooth is a replacement for cabling in a variety of personally carried applications in any setting and can also support fixed location applications such as smart energy functionality in the home (thermostats, etc.).
Wi-Fi is a wireless version of a common wired Ethernet network, and requires configuration to set up shared resources, transmit files, and to set up audio links (for example, headsets and hands-free devices). Wi-Fi uses the same radio frequencies as Bluetooth, but with higher power, resulting in higher bit rates and better range from the base station. The nearest equivalents in Bluetooth are the DUN profile, which allows devices to act as modem interfaces, and the PAN profile, which allows for ad-hoc networking.[citation needed]
==================
One benefit of Bluetooth is it chews much less power as the range is limited. I'm guessing the profile is not in 3.2 of Andriod so I'll wait and see what ICS brings.
jmone said:
Mmmm looks like my handset is only advertising that it has EMAIL and SMS as "Services" to the PC. Do you know if I need to install anything on the Handset?
Thanks
Nathan
Click to expand...
Click to collapse
Hello, have you got installed drivers for your bluetooth dongle? it looks like there is only basic microsoft service/driver automaticly installed. Usualy bluetooth module has got Broadcom chipset. Try to find out what make it is in device manager on your PC. Did you try to pair another handset to your pc? If behaviour is the same on your PC that means you need drivers for your bluetooth module. Check if cd was included with bluetooth when you bought it.
Yeah on my HD2 (WinMo 6.5) I get DUN and PAN (Windows Bluetooth services reports the device supports DUN, SPP, Telephony). On my Tab I get DUN (Windows Bluetooth services reports the device supports DUN). On my Velocity I get sod all (Windows Bluetooth services reports the device supports Email and SMS).
Win Device Mgr reports my BT Radios as Apple Braodcom Built In and the MS Bluetooth Enumerator.
Thanks
Nathan
I usually just tether via wifi and charge it off the usb still, then i can have it plugged up to power but if I need to take a call I can always disconnect it breifly without interuption to the internet... I've never really gotten on well with BT, I always found it cumbersome... that and my main laptop doesnt have BT... so wifi or usb is the only option