OK then,
I was going to get a new housing for my sad looking Ameo. They come in the standard Ameo silver or a rather smart HTC black. I already have a silver case, but here is the question.
Do the black housings, wear, scratch, or paint rub away easy? I don't want to get one and find it looks crap after six months. They ain't cheap! before anyone else says it, I know it depends how you treat it. I'm on about normal wear and tear use. How does yours look now? are there any signs of the metal underneath showing?
Regards
Jay
Black Case On The "advantage"...
Hey Jay,
I have a HTC Advantage x7501, with the black case of course, and have been using it with "typical" every-day use now for about 6 months. I have never even seen one of the silver cased "Ameo" versions of the device in person, so my review is a bit "one-sided," if you will... Also, I have a friend with whom I work with that also owns the same model as I. With saying all that, and without having experienced the silver model, I would bet the silver model would hold up a bit better on the finish due to the fact that if the silver gets scratched, the metal beneath it looks much closer to the silver finish than the black. I have a couple small blemishes on mine, and I am very particular with my mobile devices, but after using day-by-day at work and home, it has managed to get marked up just a bit. The biggest problem is, if you get a scratch on it, the metal below sticks out "like a sore thumb!"
I definitely believe that the black finish is a bit more professional looking, where sometimes the silver finishes can make a device look cheap or make it stand out.
Anyways, to give you my honest account on TWO Advantage x7501 devices (black finish) after 6 or so months of daily use, it is overall good, and neither one shows any major signs of wearing finish. Also, we both use a case that the device "slides" tightly in and out of each time you use it (without the keyboard attatched), and the device really hasn't shown any real signs of wear on the sides where it rubs the case. However, if you do happen to mark it up in any way, you will definitely notice it. Again, I am very picky, so keep that in mind, but so you have a better idea of what I am saying, I attatched a couple of pics so you can see what it looks like when or if you do scratch or mark it.
HOPE THIS HELPS!!!
-Ryan
Also Note: Only one of the devices I wrote about is pictured, but are very similar in condition, and were both purchased slightly used.
X7501 Cosmetics...
I have had my X7501 for almost 10 months now and it only has one very tiny mark on the top right corner (you have to look hard to even see it).
Since I'm also very particular about my devices (I always keep them looking new) I just used a Sharpie (permanent marking pen) to "erase" the offending mark. This works great and I would recommend it to anyone wanting to touch-up black anodized aluminum like the Athena housing.
Wow! thanks for the reply Guys, Ryan that was one hell of a reply. Must have took you a while to do that and I appreciate it. toyfreak, the idea with the marker pen is a great one. I think on just that idea alone I will get black. Its harder to touch up silver! It looks better too.
Regards
Jay
Indeed is surprisingly hard coating, I carry mine in my pockets and can't say I'm careful with it, rather the opposite, I have it since it came out and there is only a little wear in one of the corners, hardly noticeable, where the scratches are more visible, is on the silver border next to the screen, not that it look bad or anything.
Black housing - Where?
I would like to know where you can buy a black housing for your Ameo, mine needs a new one as well!
And what about your keyboard, can you get a black one too?
/HM
Silver / AMEO
Hi guys,
Proud owner of a wonderful brick since 6 months in grey color I should say that if I new I would have choosen a different color.
The grey AMEO housing is far from being "time resistant"...
Since few weeks the "video camera" around the front cam as disappeared and the "Alert" will soon do the same.
I allways take good care of my stuf and I'am bit disapointed for a 1.000 bucks machine to see it !
hmeyer said:
I would like to know where you can buy a black housing for your Ameo, mine needs a new one as well!
And what about your keyboard, can you get a black one too?
/HM
Click to expand...
Click to collapse
They are available on ebay, if you search athena case you should find them. any problems then let me know. There is a guy who does spares on there and he has them in black or Silver.
regards
Jay
Hi,
Just a quick update on the new housing. It's arrived, and I put it on. It looks great, so glad I got black. Thanks to those who took the trouble to answer this post so well.
If anyone needs a new housing for their device then let me know and I will let you know where to get them from. He claims to have a few left!
regards
Jay
responderman said:
Hi,
Just a quick update on the new housing. It's arrived, and I put it on. It looks great, so glad I got black. Thanks to those who took the trouble to answer this post so well.
If anyone needs a new housing for their device then let me know and I will let you know where to get them from. He claims to have a few left!
regards
Jay
Click to expand...
Click to collapse
I'm looking for a new housing, for the X7501 not the 7500. Please advise me where to find one.
tootallk2000 said:
I'm looking for a new housing, for the X7501 not the 7500. Please advise me where to find one.
Click to expand...
Click to collapse
Forgive my ignorance, What is the difference?
Jay
responderman said:
Forgive my ignorance, What is the difference?
Jay
Click to expand...
Click to collapse
The X7501 does not have the internal or 2nd camera, the X7500 does. So I would have a big hole in my unit if I used that one. I don't know if the inside layout is any different but that's the only visible thing on the external end.
I need a new housing too.
Anychance you could PM me a link or contact for this.
Thanks in advance.
tootallk2000 said:
The X7501 does not have the internal or 2nd camera, the X7500 does. So I would have a big hole in my unit if I used that one. I don't know if the inside layout is any different but that's the only visible thing on the external end.
Click to expand...
Click to collapse
7501 does have 2 cams. the 7510 doesnt
goodluckje said:
7501 does have 2 cams. the 7510 doesnt
Click to expand...
Click to collapse
LMAO dude have you been drinking? The 7501 has 1 camera and the 7500 and the 7510 has 2. I own the 7501 which is also cheaper than the 7500. I suggest you google them and you'll see the difference.
tootallk is correct. 7501 has 1.
back to the subjct of cases. i got the nutshell case mentioned elsewhere in this forum. definitely woth the money... and the wait. beautiful case and funtional.
wgary said:
back to the subjct of cases. i got the nutshell case mentioned elsewhere in this forum. definitely woth the money... and the wait. beautiful case and funtional.
Click to expand...
Click to collapse
hi
you are talking about a extra case to protect the athena right?, the thread is about replacing the cover / housing of the athena itself, a step that becomes nesesary when you not use case like your nutshell .
anyhow (and to really come back to subject ) i have to replace my housing too and wonder, why nobody can simply post the web/email adress of a reseller here?. i searched alot now an only find companies in asia and prices 'far away from reality', so if someone know a good reseler please post here.
thanks mad
madbird said:
hi
you are talking about a extra case to protect the athena right?, the thread is about replacing the cover / housing of the athena itself, a step that becomes nesesary when you not use case like your nutshell .
anyhow (and to really come back to subject ) i have to replace my housing too and wonder, why nobody can simply post the web/email adress of a reseller here?. i searched alot now an only find companies in asia and prices 'far away from reality', so if someone know a good reseler please post here.
thanks mad
Click to expand...
Click to collapse
oops my bad.
madbird said:
hi
you are talking about a extra case to protect the athena right?, the thread is about replacing the cover / housing of the athena itself, a step that becomes nesesary when you not use case like your nutshell .
anyhow (and to really come back to subject ) i have to replace my housing too and wonder, why nobody can simply post the web/email adress of a reseller here?. i searched alot now an only find companies in asia and prices 'far away from reality', so if someone know a good reseler please post here.
thanks mad
Click to expand...
Click to collapse
Here you go,
http://search.stores.ebay.co.uk/sk-...shopQQfsooZ1QQfsopZ1QQsaselZ239115870QQsofpZ0
Not cheap though!
Jay
P.S if im in trouble "Madbird" made me do it
Related
Im looking at either getting the nice leather case, the official HTC one "Diamond Pouch PO S390" (seen in this thread here... http://forum.xda-developers.com/showthread.php?t=403691) or this http://cgi.ebay.co.uk/HTC-Touch-Dia...photoQQcmdZViewItemQQ_trksidZp1713.m153.l1262
Anyone got a crystal case for their Touch Diamond? If so whats it like?
Im looking to protect my Diamond as I know how easy to scratch and mark they are (its doing ok at the moment but id like to keep it protected and looking like new)
Thanks, any feedback would be appreciated
I got one yesterday ( for $15 CDN ==" since i didn't want to wait for shipping)
from what i've seen so far
Seems like a great case, it is a tight fit for the diamond, so there are some worries with regards to upgrading the battery in the future....
But aside from that, it does its job of protecting my diamond and the change in dimensiosn is barely noticeable to me.
Moderators Could you move this to Diamond Accessories please, sorry, thought I had posted it in there, but hadnt.
Thanks for the feedback, sounds positive, I want to get a leather case, but at the same time its nice if i can just use it rather than get it out of the leather case to use it.
Mmm, food for thought!
yse mods please move the thread ^^"
i was contemplating the leather case as well before...
the benefit to the hard case is that its as it doesn't make it more difficult to access the phone and you dont need to take it out of the case to do anything
the only pet peeve i have with my case is that the power button on the top left is now a bit harder to press due to the case
just my 2 cents
Most of the crystal cases i have come across are dust magnets...so that puts me off them. Ive ordered the pouch today from Expansys...the official one although i have to wait 3 days before they come into stock..
Had one of these plastic cases on a samsung phone - the case cracked after a few days Lets hope these are different
One reason why im staying off silicon/crystal cases is so that I could enjoy the flushed screen.
Strange.. U guys don't seem to find it a luxury to have a flushed screen. I love it as I don't need to finger-wrestle in order to tap the 'X' button...
MasK, thats a very good point! I know what you mean there, very frustrating.
Mmm, think im just gonna opt for the Leather Case. Think I would just get frustrated with the Crystal Case.
Thanks for your feedback and comments guys.
Slightly off topic...
But do you think somebody (HTC or after-market company) will produce a soft touch / matt finish rear cover for the Diamond? I mean, its an easily replaceable, small piece of plastic and would protect (or hide) fingerprints and make it less scratchy if its soft?
Just a though... if any external companies looking it at, I'll pay £2.99 for a rip off soft touch back cover on eBay from Hong Kong
DG
Hey all! I just wanted to share what I found. Not to sure if anyone found this and or mentioned it here somewhere. I looked around and saw another post asking about it. But thats all I saw. I am not sure how easy it is to dis-assemble the device and or how well the housing varies with hardware. I changed my T-Mobile Wing into the HTC 4520 with housing replacement, yes they were the exact same hardware wise yet some components were off some how. I had changed more then a few others that wanted the HTC branded housing and same so idk. I'm going to order one of these soon so i will share with pics of my experience unless someone does it first. Here you all go.
http://www.truesupplier.com/_search.php?page=1&q=htc+magic
ps: trackballs too!!!!!!!!
Nice! Too bad the custom ones are ugly as hell
Nice I was JUST looking for housings. Thanks for the heads up!
Just in case you guys aren't aware, 32A and 32B motherboards are different, so a HTC Magic housing will not fit a MyTouch, and vice versa.
masr1979 said:
Just in case you guys aren't aware, 32A and 32B motherboards are different, so a HTC Magic housing will not fit a MyTouch, and vice versa.
Click to expand...
Click to collapse
ya i had a feeling about this. but i think im still gonna try and see what needs to be modded. you never know, htc might have made the molds the same so they dont lose on machining time. like i said in op my wing and the 4520 were off by just a lil but i still got it to work 100%. I only had to switch out the keyboards so i bet this will probably work. I will get it and try it out for mt3g users.
iPhone iWing said:
ya i had a feeling about this. but i think im still gonna try and see what needs to be modded. you never know, htc might have made the molds the same so they dont lose on machining time. like i said in op my wing and the 4520 were off by just a lil but i still got it to work 100%. I only had to switch out the keyboards so i bet this will probably work. I will get it and try it out for mt3g users.
Click to expand...
Click to collapse
I'm speaking from personal experience. I bought a G2 case from ebay, and the case has some holes on the opposite side of where the MyTouch case has them. I ordered a second one and had to return it because despite asking the seller in advance if it indeed was for a MyTouch and not an HTC branded phone they didn't have the right one. I've seen recently that some have started popping out on ebay that state "will fit US models" or something to that effect, these should be safe. My advice is to ask before you buy if it will fit a T-Mobile MyTouch, and what happens if it doesn't fit after you order it.
yep i can confirm. the thickness is different. but i managed to match them i have a 32a front and back pannel (black). And 32b middle section (silver UK Vodafone stock). This works just fine. Otherwise your vibration motor will never work since it is to tight.
zmesler said:
yep i can confirm. the thickness is different. but i managed to match them i have a 32a front and back pannel (black). And 32b middle section (silver UK Vodafone stock). This works just fine. Otherwise your vibration motor will never work since it is to tight.
Click to expand...
Click to collapse
I double that, I just figuered that out the other day while I was trying to change the housing for my magic.
I was wondering if anyone has found a source for a housing replacement that will automatically fit the 32B? I am in search of one and can't seem to find one. I found some that say mytouch compatible but I think they will have the same issue as mentioned here about being different on the inside.
Thanks.
typedink said:
I was wondering if anyone has found a source for a housing replacement that will automatically fit the 32B? I am in search of one and can't seem to find one. I found some that say mytouch compatible but I think they will have the same issue as mentioned here about being different on the inside.
Thanks.
Click to expand...
Click to collapse
Same here. In need of a new housing. There must be SOMEWHERE we can get one. Anyone? Help!
Temporarily said:
Same here. In need of a new housing. There must be SOMEWHERE we can get one. Anyone? Help!
Click to expand...
Click to collapse
I'm also looking for a housing that will be compatible with my MT3G, it looks pretty banged up.
yea the housings cause vibrator problems.
I bring great news, I e-mailed cnn.cn asking when they will have MT3G housings in stock and they replied saying they should have it in stock in early march.
iPhone iWing said:
Hey all! I just wanted to share what I found. Not to sure if anyone found this and or mentioned it here somewhere. I looked around and saw another post asking about it. But thats all I saw. I am not sure how easy it is to dis-assemble the device and or how well the housing varies with hardware. I changed my T-Mobile Wing into the HTC 4520 with housing replacement, yes they were the exact same hardware wise yet some components were off some how. I had changed more then a few others that wanted the HTC branded housing and same so idk. I'm going to order one of these soon so i will share with pics of my experience unless someone does it first. Here you all go.
http://www.truesupplier.com/_search.php?page=1&q=htc+magic
ps: trackballs too!!!!!!!!
Click to expand...
Click to collapse
I bought one of the housings available from the website posted in the OP (and quoted above). The only part of my MT3G that was messed up and scratched was the front face plate, so I didn't bother trying to swap out the rest of the housing. The face plate fits perfectly and looks awesome. The chrome buttons and HTC logo instead of the T-Mobile logo give it a much nicer look. $17 to make my phone look nicer and brand new again is not a bad deal at all.
I'd actually be willing to bet that, with some minor modifications to the middle section of the housing, we could get this entire kit to fit our MT3G's. We'd need to drill a tiny hole for the mic (the one that shipped to me has the mic hole on the opposite side), and perhaps cut away at some of the plastic near the vibration motor to allow it to move freely, but it should work. I might try this if I get bored. I'll let you know if I have any success.
Thanks for posting the site.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300400807287&ssPageName=STRK:MEWAX:IT
iluvmymytouch said:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300400807287&ssPageName=STRK:MEWAX:IT
Click to expand...
Click to collapse
I bought from this guy, and he has sent me the wrong size screwdriver. Check out his feedback first, it's not very reassuring.
alliekhat said:
I bought from this guy, and he has sent me the wrong size screwdriver. Check out his feedback first, it's not very reassuring.
Click to expand...
Click to collapse
Other than the screwdrivers, was the housing nice?
KAwAtA said:
Other than the screwdrivers, was the housing nice?
Click to expand...
Click to collapse
It was okay, but just okay. It definitely looks like OEM product, even down to the fact that the HTC branding was tinged blue instead of being silver and the middle chassis part was cracked. I waited 3 weeks for it to arrive in this condition, and I'm still struggling to get a refund from him so I can try another seller. Don't waste your time with him.
I did notice one or two listings on ebay actually do say original not OEM, one in particular from the UK, going to give one of those a try.
alliekhat said:
It was okay, but just okay. It definitely looks like OEM product, even down to the fact that the HTC branding was tinged blue instead of being silver and the middle chassis part was cracked. I waited 3 weeks for it to arrive in this condition, and I'm still struggling to get a refund from him so I can try another seller. Don't waste your time with him.
I did notice one or two listings on ebay actually do say original not OEM, one in particular from the UK, going to give one of those a try.
Click to expand...
Click to collapse
Let us know who you get it from. I dropped mine and there are little chips around the phone, I'd like to replace the housing eventually.
guys I need a housing for my Tmobile Mytouch without 3.5 mm jack ASAP. my back looks like crap, and scratched like hell.
here are 2 different ones from ebay. can you guys tell me if it will fit? I mean the pic does say "tmobile" and I am waiting from the sellers to hit back.
both of em are shipped from hong kong
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=280476103537&ssPageName=ADME:X:RTQ:US:1123
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=290413949633
btw both are similar products but 2 different sellers.
none of those come with screws. and one of them states, I would need existing "screw holes" idk what that means, I believe these "screw holes" are already inside my pre existing housing (stock).
sorry but these guys are foreign sellers and have bad communication skills, most of there responses are half assed.
Hi guys,
Recently purchased a new hd2 and wondered if there are any pull cases available for it, my google and xda searches have been inconclusive.
thanks
shure2 said:
Hi guys,
Recently purchased a new hd2 and wondered if there are any pull cases available for it, my google and xda searches have been inconclusive.
thanks
Click to expand...
Click to collapse
What's a pull case ?
compact_bijou said:
What's a pull case ?
Click to expand...
Click to collapse
where you pull a strip up on the back of the case which lifts the phone out of the case slightly
I bought one from a seller on eBay.
I had to search 'HD2 case', and then find it by looking at the pictures, very few on there though.
bbobeckyj said:
I bought one from a seller on eBay.
I had to search 'HD2 case', and then find it by looking at the pictures, very few on there though.
Click to expand...
Click to collapse
Bung him a link then !
compact_bijou said:
Bung him a link then !
Click to expand...
Click to collapse
I'm sure he knows how to find eBay
I bought it months ago, I would have to troll through all the listings to find it again.
Seeing as I'm feeling generous:
http://cgi.ebay.co.uk/New-Etui-Cuir...honie_Accessoires_Mobiles&hash=item19bf1e084e
http://cgi.ebay.co.uk/New-Leather-C...009221?pt=PDA_Accessories&hash=item19b9a87c45
http://cgi.ebay.co.uk/Genuine-Leath...902834?pt=PDA_Accessories&hash=item19bf413032
http://cgi.ebay.co.uk/Leather-Case-..._MobilePhonesCasesPouches&hash=item20b4074f76
http://cgi.ebay.co.uk/Leather-Case-...230125?pt=PDA_Accessories&hash=item1c15f175ad
http://cgi.ebay.co.uk/Black-Faux-Le..._MobilePhonesCasesPouches&hash=item43a20246bc
A great Pull case
Here is a case i bought from ebay. It arrived today and after testing it for a couple of hours I am posting my positive comments and recommendations on it. First of all - it is the cheapest pull case of the "puller is fixed in hole on the side" type (see pictures). Costed me just 8$ (free shipping to Taiwan)
It may seem expensive given the fact that one can order a pull-case for just 2.07$ as in here. But after a sad experience i had with hard case i learned the lession with sad consequences. This case is well worth the price. Soft pleasant leather, soft inner velvet lining, and the pulling design is just brilliant. I used to have a conventional pull case with not fixed "puller tongue". Well, every time i was going to put the phone back into case i had to make sure that the tongue is on the right side (otherwise the phone would not dive till the end) - annoying, especially if you have to do this operation fast, "on the flight". With this design you do not look for the tongue neither while inserting, nor while pulling the phone out.
Too long a review for just a leather case... anyways, nice purchase it seems:
The photos are from ebay site.
P.S. Also they include a screen protector, but i doubt the quality of it, though haven't tried it yet (it seems 0.5 mm longer then needed).
P.S.2 I am by no means related to the seller, I just searched ebay for a leather case, sorted them by S&H price and scrolled down until i found the first one with this design.
Guys im from the Netherlands and I can't vind this case anywere why?!!!?!
I want to have the case before my phone comes so I won't damage it that fast I know how I im.. ghehe
Rolando88 said:
Guys im from the Netherlands and I can't vind this case anywere why?!!!?!
I want to have the case before my phone comes so I won't damage it that fast I know how I im.. ghehe
Click to expand...
Click to collapse
I dont believe Sprint is selling it yet.
Go to Verizon.com thats where I ordered mine from.
It doesnt have a Verizon logo on it anywhere and works fine.
jayjam99 said:
I dont believe Sprint is selling it yet.
Go to Verizon.com thats where I ordered mine from.
It doesnt have a Verizon logo on it anywhere and works fine.
Click to expand...
Click to collapse
woo! thank you! bene looking all over for this, spend 5 more bucks on some cleaning wipes in order to get the free overnight shipping over 49.00 as the case is only 44.99..
penskyc said:
woo! thank you! bene looking all over for this, spend 5 more bucks on some cleaning wipes in order to get the free overnight shipping over 49.00 as the case is only 44.99..
Click to expand...
Click to collapse
im trying to get rid of mine if you want...
rahtrip said:
im trying to get rid of mine if you want...
Click to expand...
Click to collapse
How much to ship it to the UK?
johnboywilson said:
How much to ship it to the UK?
Click to expand...
Click to collapse
lemme see
rahtrip said:
lemme see
Click to expand...
Click to collapse
Thank You
rahtrip said:
im trying to get rid of mine if you want...
Click to expand...
Click to collapse
If you flip over the cover, does it work to support the phone as a kickstand in landscape?
Sent from my HTC One_M8 using Tapatalk
GermanGuy said:
If you flip over the cover, does it work to support the phone as a kickstand in landscape?
Sent from my HTC One_M8 using Tapatalk
Click to expand...
Click to collapse
Nope. It just slips and falls over.
Have had the case now for over a day and I do have a few thoughts about it. Purchased at a Verizon store last Sat(none in my area had it in stock apparently) for $48 with tax and 3 day shipping to my home. Color was the grey which I thought went really well with my gunmetal model. Upon putting it on the phone I felt that the fit was spot on. The back snapped right into place and the front flip cover rests evenly on the screen. Functionality of the case is second to none. It works as advertised ranging from being able to see time and current weather conditions to making and answering calls.
Some of the other things that will light up are any incoming text messages and you can also dismiss any alarms that you have set to go off by simply following the gestures. A big question that I had when I bought the case was whether or not that the music playback would be hindered. I'm very happy to report that audio playback was just as clear and precise as if the cover wasn't over the front of the device. Another plus is when you open the cover the phone automatically unlocks and the screen shuts off when the cover goes back on. Thus greatly eliminating use of the top mounted power button.
I felt the choice of the materials for the case were not bad. The rear material certainly doesn't feel like a cheap plastic by any means, but it's nowhere near as nice as the phone's metal finish. The most comfortable way of using the phone for me was to hold the cover with my left hand and use my right to operate the phone itself. Now, I have rather large hands so this could obviously be different if you weren't blessed with such a thing. Folding the front of the case back over the rear proved to be uncomfortable to me. Another downside is the fact that the front cover cannot double as a kickstand when positioning the phone in landscape. When done so, the phone just falls flat on its back.
Overall, I definitely like the case. It has that wow factor to it as everyone I have showed it to have been amazed by it's functionality. The only things that HTC should improve on it is to have the front flap being able to fold back and stay flush on the rear of the device. I also would had like for the front flap to stay open when you open, but the trade off is that when it springs back into position it does a good job of staying over the screen, even in a loose pocket. I noticed no addition use of the screen during the day in Gsam battery monitor. If I were to give it a score out of 10 I'd place it at an 8. Only major cons would be price and certain aspects of holding the device depending on hand size.
I'd have to tip my hat to HTC for coming up with the concept. If anyone has anymore questions about it feel free to ask.
Found this on ebay:
http://www.ebay.de/itm/HTC-One-m8-dot-View-Hulle-Cover-Neu-/271443579895?pt=DE_Handy_PDA_Taschen_Schutzh%C3%BCllen&hash=item3f334c53f7
i ordered a dot view but my provider wrote me that they will deliver later in may
Rudimente said:
i ordered a dot view but my provider wrote me that they will deliver later in may
Click to expand...
Click to collapse
What is your provider? It looks like the black ones are available on Verizon.com again (they were sold out all week). Just ordered one for a friend.
Supacat said:
What is your provider? It looks like the black ones are available on Verizon.com again (they were sold out all week). Just ordered one for a friend.
Click to expand...
Click to collapse
german t-mobile is my provider
Rudimente said:
german t-mobile is my provider
Click to expand...
Click to collapse
I'm having german t-mobile as well, they told me today that the cases should arrive this week..? but don't know how true that is..
amazon started listing the colored variations today, but all of them are marked as "available for preorder"
any chance you could post a couple of pics showing what the case looks like when open and folded back? All the photos i've seen of it don't show this. want to know how much it bulks the phone out.
cheers
Managed to pick the one and only one of these up from my local Phones4U in Croydon today, then went to the other local Phones4U and bough the other one, looks like they are finally starting to trickle in.
Figured out how to get the case to function as a kickstand. It's simple, but involves needing something else like a laptop or book as a prop. Simply open the cover and fold it over the back of the device. Then just rest the device on the laptop or book of your choice. Then, boom it stays put in place and with the way I got it, the angle is pretty nice for viewing.
Hello X fold gang!
My device is on the way to the UK, should be with me in the coming days. Beyond excited!
Wanted to order some sort of case/cover for it, any advice or links on the best ones out there in your opinion? Photo evidence much appreciated
Currently looking at something like this:
https://a.aliexpress.com/_vBMZeg
minimarcy said:
Hello X fold gang!
My device is on the way to the UK, should be with me in the coming days. Beyond excited!
Wanted to order some sort of case/cover for it, any advice or links on the best ones out there in your opinion? Photo evidence much appreciated
Currently looking at something like this:
https://a.aliexpress.com/_vBMZeg
Click to expand...
Click to collapse
Well, i bought one and received it. The quality is really poor compared to the vivo original black one. I wanted to match my blue phone. Wrong idea. I will keep my black ordinal vivo. Better coverage, better material.
timalpipo said:
Well, i bought one and received it. The quality is really poor compared to the vivo original black one. I wanted to match my blue phone. Wrong idea. I will keep my black ordinal vivo. Better coverage, better material.
Click to expand...
Click to collapse
Eek, great advice! I got the blue colour phone, so like you - wanted to match. Maybe i'll not bother!
Hi, so far I see this is the best looking case for the X Fold but the only thing hold me back is the shipping take over a month to come
https://a.aliexpress.com/_mLfYHYS
Candy_girl2008 said:
Hi, so far I see this is the best looking case for the X Fold but the only thing hold me back is the shipping take over a month to come
https://a.aliexpress.com/_mLfYHYS
Click to expand...
Click to collapse
The only problem is that you will not get the wireless charge anymore. With that metal piece on the back.
And i you read comment, you loose fingerprint unlock on front screen... Too much inconvenient for me.
I ordered the Vivo case with the phone. Quite happy with the protection and it doesn't add a lot of weight - the phone is already heavy enough!
Candy_girl2008 said:
Hi, so far I see this is the best looking case for the X Fold but the only thing hold me back is the shipping take over a month to come
https://a.aliexpress.com/_mLfYHYS
Click to expand...
Click to collapse
this is what i got. i didn't like the front frame, so i removed it. it blocks the bezel. you see, there are functions nowadays (such as sideapp menu, back button) that require user's finger to hold the very tip of the screen for half a second before the menu popups. then again, without that frame you may damage your front screen if it falls. secondly, the stand in the back requires a hard surface in order to hold it stilll. then again, i wouldn't say this is a bad case overall. but it has its flaws. the rest i am satisfied. the material, the durability, it fits well and it covers the side well.