i took it out of my pocket to see what time it was, and the phone is white, i reset it, hard reset it, flashed new rom, flashed new spl.. no luck.. everything is just white.. phones operation remains intact.. but i cannot see anything that is happening. there is probably a thread on here about it, but all i saw was about wrecked spl flashes.. what can i do?
A number of people (including myself) have experienced issues with the Tilt screen going to a permanently "washed out" white. Unfortunately, this appears to be a hardware defect, and the only thing you can do at this point is flash everything back to the original settings and exchange the phone (assuming it's still under warranty).
Brrrrrr. This sounds like the horrors with the hermes!!!! Plz. let this not be true, it is the reason why I am stuck with a Kaiser for 2 years now instead of with a Touch Pro/Vario IV at the end of this summer :-((
By the way shouldn't this post be moved to Kaiser General?
return it its coverd under warantee or even if is not they'll fix it its known issue
turned white you say? quick head down to the apple store. you can bump it for 350!
just remember to say "no im serious...its real...look...theres the 3g sign.
Just buy a new LCD....i believe the problem is in the flex cable going to the screen. Hardware problem's suck. But it's the only fix i know..or send it to one of those expensive fix places online.
Like when poop gets really old it turns white?
i had this happen before on an old tilt. it happened on hot days outside the screen would turn white. i couldnt figure it out, it prolly happened about 10 or 15 times this summer.
my fix...
mash down on the area around the lcd. most of the time it worked if i mashed down in the center of the little 1/4 inch thick strip of plastic btwn the bottom of the screen & the bottom buttons. if that doesnt work, try all around that strip. that worked prolly 90 or 95% of the time for me. a couple times it didnt work & i had to mash around the whole screen.
i know it doesnt sound kosher, but hey percussive maintenance always worked back in my vcr days.
Related
i just recently bought my xda2s and it worked fine for a week though. now, from time to time my screen would be "untouchable". literally i cannot click anything or open anything even if i soft-reset it for 10x. buttons seem to work fine but the screen does not. it happened twice while my bluetooth was "on" and i thought maybe it was the bluetooth but recently the same thing happened with my bluetooth now turned "off". i have to wait for hours before it would return to normal again. Anybody help please? By the way, my bluetooth version is 1.0.0 build 3500.
I had a similar problem on my Samsung SPH-i700 PocketPC Phone through Verizon Wireless. Even after a hard reset, I couldn't get past the screen calibration, until I found out that a piece of hair and debris found on the outer edge of the screen right under the lip of the cover was interfering with the touch portion of the display. Apparently, the touch sensors extend past the visible area of the screen, so with both a little aircan and vacuum cleaning, the debris was picked up and the touch screen functioned normally again.
Is this a consistent and/or intermittent problem? Did a hard reset resolve anything?
look for the alignment
Do you have Calligragher 7.4 installed? I read about this in Tekguru website that if you re-install 7.3, the problem goes away. That is what I have done and it seems to be working for me so far (2 days test).
i've checked out my screen and i dont see any dirt or something... i even have a screen protector... dont know if that might cause the problem. Same thing happened last night but this time it was just for a short period of time then it went back to normal... I didn't try a hard reset cause i dont want to loose some of my files but if ever it happened again, i might try doing a hard reset and see what happens... right now, im having my xda2s checked if maybe it's a factory defect or something...
regarding the caligrapher program thing, i dont have that...
Hey, i have the exact same problem I bought mine here in Toronto, from an Asian dealer, its the O2 XDA IIs asia-pacific model.
Same problem, screen(touch screen) goes dead like no responses to any touches, for like half hour - 2hour once in a day or something and nothing cures it, hard soft rest nothing. just with time it suddenly starts working and the Handheld is useless until then...well i dont see any cure and this is the only place i have heard about someone else having this issue, i will take it back to the dealer, in hopes of exchanging.
any feedback will be will be appreciated
overclock it for a few days..that fixed mine..dont know how but it did.
There is a tread in blue angel about screen aliment that you might like to read. seems 4k of devices went out with screen problems.
What is overclock it. Fairly new to this. Mine just keeps trying to allign and thats all it does it doesnt go into boot mode just allign screen all the time
So, i'm usually quiet on these forums. Just reading, trying roms, etc. But here is something that has me stumped. Last thursday my phone crapped out. When i woke up and looked at it (it was connected to my laptop/charging) Applications were opening left and right, i couldn't close any of them because stuff kept opening. I tried to soft reboot it and it didn't help. Once it rebooted stuff started opening itself at random again. I ended up pulling the SIM and battery out and leaving it for 5 minutes. When i put it back and powered it up the touch screen no longer worked, but apps weren't opening on their own.
What gives?
I have hard reset (which means it's waiting for me to touch the screen to setup my rom), i have also taken off the screen protector (in case it had something stuck under it. Neither of these things helped. Per the forums I got a new screen, just put it in, and the touch screen doesn't work still... I'm drawing a blank here can anyone give me some advice. Going back to my Prophet for the time being but I HATE not having a keyboard (and it's slower than molasses)
have you tried flashing a new rom via sd?
Check that the screen protector has not moved under the front bezel and keeps pressing your touchscreen.
Robert
I have totally removed the screen protector and even replaced the screen for that matter so I dont think that's it. I haven't tried flashing a new rom. I just found it odd that this has worked for so long and now I get what appears to be hardware problems. As for flashing Via SD memory, is that better than doing it via cable for some reason? I'd be willing to give it a go...
Any other suggestions?
fiddelm3742 said:
I have totally removed the screen protector and even replaced the screen for that matter so I dont think that's it. I haven't tried flashing a new rom. I just found it odd that this has worked for so long and now I get what appears to be hardware problems. As for flashing Via SD memory, is that better than doing it via cable for some reason? I'd be willing to give it a go...
Click to expand...
Click to collapse
Similar problem happened to my Kaiser phone, although no multiple files opened, the phone just won't react to any touching, not stylus pen either. So I first soft reset, then hard reset, none of them works, now the phone can Sync alright, but the screen just stands on the Window Mobile screen, saying "Tap the screen to set up your window mobile device"
I only have this new phone for <3 weeks.
I went to HTC site, want to download a latest ROM file from them, after typing in the S/N, it won't let me, saying that ROM is not suitable for my phone.
So now I am download ROM file from this site, will choose one to flash the phone, see whether it works.
I will call HTC tech support tomorrow after Thanksgiving, see what they suggest
Hope some gurus here can also make some suggestion, Thanks!
Well I replaced the LCD and the new LCD works great, but the screen still doesn't respond to touches. What gives?! I hard reset and I got past the windows screen alignment thing by creating a welcome.not file but it's still pretty much worthless w/o a touch screen. Anyone have any suggestions?
Whoa, i thought something odd was going on. Never mind i got entirely the wrong idea.
Ha, not the case.
Anyone know if a flex cable would fix my issue? I dont really know what the felx cable is for but i've seen posts about people replacing them w/ LCD problems. I don't know if it is touch screen related or not, and i'm kind of tired of buying parts that don't fix my problem
please just flash a new rom whch ever you want (for some reason i thought you said that it keeps restarting your device because if that was the case the only option you would have was to flash via sd as activesync would load long enough for you to get a connection to flash from the computer)..trust me just try it..what have you got to lose
I reflashed one yesterday actually. The newest HyperDragon (which is looks like a new one is available today) It wasn't rebooting but initially windows were popping open left and right so i restarted it a couple of times(which i first had the problem, not yesterday) Yesterday it worked like any normal rom w/o the ability to touch. Anywho, after the flash of a different rom. No luck. I'm thinking it's a hardware problem of some sort but as i've already replaced the LCD i have no idea what?
yah thats sounds funky..you can bring it in for a warranty exchange either at a local DSC or over the phone (that is if your with att) and if not call HTC..all devcies come with a 16 or 18 month warranty
Well I called ATT yesterday, apparently I purchased the phone On Oct 17th 2007 which means It's out of warranty (apparently it has a 12 month warranty?) So it sounds like I'm SOL. So, i guess I'm off to ebay to try and fine a phone that I can canibalize to try and get mine going again.
touch screen
this may sound dum but when you replaced the screen did you replace the touch part as this is different from the screen
Well I picked up this
http://www.blackberry8100parts.com/...B3-NEW-HTC-TyTN-II-KAISER-P4550-_p_35-70.html
which includes the digitizer (from what I know it's all one part when they send it to you) The screen has the digitizer built in. So i replaced the part they sent me.
I just stated having this issue. My touchscreen stopped responding to touches over the weekend while the keyboard was extended. I just took the phone apart to make sure everything was connected right & put it back together, & now the touchscreen doesn't work at all. This sucks!
Any news? i'm having the same problem: no response at all, stuck at "Tap the screen to set up Windows Mobile-based device"
An interesting problem with screen
well my tilt fell out of the car holster while using gps and i suspect the screen hit my gear shift. I didn't notice anything odd after i put the battery back in it (yeah it fell that hard lol). Later that night I went to check mail and noticed something not right. Turns out my screen seems to have been pushed in a bit. Well here's the issues I've noticed so far: All the touch responses seem fine except for 1) the screen alignment doesn't register taps, but otherwise the touchscreen works and 2) on the htc home screen, I can't tap the house icon unless I tap any other icon first.
Initially I thought there was some pressure or deformation right at that particular spot, but it reacts the exact same way in landscape mode. I can't tap the house icon first; I have to tap something else first, then the icon works fine until I open a program or something and go back to the home screen. Then I simply have to tap weather or something and then home.
I'd reflash the rom or do a hard reset, but the screen alignment didn't work when I tried it so I didn't want to get stuck at the "tap your screen to begin" part.
Any ideas or do I just need to buy another screen or maybe just the digitizer. the amount the screen seems recessed is maybe a millimeter at most. Just enough so that I noticed a difference when touching contacts just above the housing. I tried cleaning by using a business card and running between screen and housing. Ohh... and one more thing... when I open the cube and then close it, I get what I refer to a static frazzle for split second and it goes back to normal. That only happened a couple of times after the business card thing. Do you think I just loosened a connection? damn... I still haven't taken it apart yet. Think I need to. Any help appreciated.
If your screen does not work, you can still use your phone. There is an app that you use on your computer that acts as the touch screen. This also works when the screen craps out.
http://www.sparus-software.com/spip.php?page=download&lang=en&ref=at&t=tilt
(EveryWAN Remote Support Personal Edition - Free download)
yeah -- my touchscreen didn't crap out totally, it just got muffed up when I dropped it a bit. Well, i went ahead and installed codefreaks remote screen alignment thing and did a hard reset. Well, the hardreset did the trick w/out the need for anything else. The alignment worked and everything. So, i'm back in business. Everything seems to work properly, except that my screen is still recessed a tad; but, that's not a big deal really.
Here's my story:
I recently bought this phone for only $125 - not bad deal if you ask me. I knew from the beginning that the screen was a little mess up, even the guy I bought it from knew that. You would need a flash light in order to see what was on the screen. From any other point of view, it's just totally dark/black. So the guy was gracious enough to include a new lcd screen which he ordered to replace the old one. So I decided to undertake the task of putting it in myself. Once that was all said and done, I powered the tilt up and it was doing the exact same thing before I put the new lcd screen in, which was not lighting up the screen and it was still very dark to see anything.
With a flashlight, you can see that it's still working and the touchscreen works fine too. I think another person posted a thread with the same problem, but no one really replied back to him. Has anyone come across this problem before? Some have said that it's the flex cable that connects to the front d-pad and lcd screen itself is the cause for the back light issue. Any suggestions out there?
If I were you I'd try to figure out the pinouts for the LCD panel. Try to see if the Kaiser is outputting the necessary voltage for the backlight. Also try the opposite and apply voltage to the LCD to test the backlight.
Unless it is 2 back LCDs, I'm assuming there is a fault somewhere internal and not turning on the backlight.
I've never taken my tilt apart, but this is where I would start.
I wouldn't know where to begin to troubleshoot a device like this. Lol! It's fairly easy to take apart - there's actually a video on youtube that takes you step-by-step. I guess this isn't as common as some problems are, but I don't want to spend money having someone else fix something that could be so minute. And prices for some of the replacement parts are almost as expensive as what I bought the phone for.
When I took my tilt apart, physically, everything looked good from what my eyes can see. A little cleaning here and there, nothing major. The guy who had it before me flashed the rom to try and make it look like it had touchflo on it so I reflashed it back to the original rom software (or at least, whatever was on the HTC website). I tried doing hard resets, soft resets, rom flashing and everything, still no luck.
i got my td2 just about a week. yesterday suddenly the touchscreen didnt work at all anymore! i was taking some pictures and then it stopped to do anything on the touchscreen. i rebootet the device few times but no go - even removed the battery but didnt work anymore. then i left the device a few minutes without battery and when i tried it again it worked. this scared me a little... because without touchscreen u are really lost with this phone.
ohwell.. i hope this doesnt happen again. but i actually got another strange thing here:
if i look into the screen from the side.. i can see a strange glimmer sometimes. it looks like oil in water... it does glimmer a little and its not visible all over the screen but the part does even grow. i noticed this yesterday and it was like 5cm long and 2cm width. but now its almost on the full screen and it looks like the effect when u press on a LCD screen really hard. but it appears without doing anything.. does anyone have that too on his TD2??
same problem here. its the device of a friend. one week old. but we didn´t managed it to bring it back to life again...
no we will try a hard reset.
battery was out for ar least 30min wizhout success.
even noticed some glimmer at the screen. hard to describe. like liquid between sreen and screen protector.... but only on those parts were we tapped on the screen...
no we try the hard reset - i´ll report how it worked.
somebody else with that problem here?
ok we tried a hard reset - no success. screen is dead. no way to setup the device. no reaction of the touch screen. will go to the o2 shop tomorrow and bring it back...
wow.. at least im not the only one. my screen is working again but the glimmer didnt go away. also today appeared one more defect on the screen - it looked like the protection plastic is moving, but then after some tapping on the screen it went away again. very strange!
the glimmer looks indeed like a liquid between the screen and the protection. sometimes its almost not visibe and sometimes its really good to see. i wonder whats going on here..
hey i just found something out!!
my screen has something like little bubbles under it when i do touch it on a certain area. when these bubbles are visible.. my screen does not work anymore!! then i can clean the screen a while with a tissue or my tshirt or whatever and the bubbles go away - as soon they are not visible anymore the touchscreen works again!!!
im tryin now to give that phone back and get a new one. i dont even have that phone 1 week!!
I have a Diamond2 with the same frozen screen issue. The screen just did not react to any tap. Soft reset may put it back to work again, but the symptom repeated after some time. Even hard reset cannot rectify the problem. It is hardware defect. Fortunately it is one week old and still within the one-to-one exchange policy and I can take back to the shop I bought push for an exchange. Having email HTC and they just ask for service check and refuse to exchange a new one. If you conduct a Google search of freeze screen, you may locate a lot of touch screen issue but only very limited solution. I suggest you to have the device exchange than going to repair.
Does it look like this: http://forum.xda-developers.com/showthread.php?p=2557175#post2557175???
Hi, I am experiencing the very same problem. Touchscreen stopped working. Taking out the battery for 5 minutes fixed it. But there is a oily liquid now beneath the screen. My device is 5 days old, this should not happen
Taking it to the shop on monday.
we tried everything but without any succes...
today we gave back the phone. it was within the one week limit. but there is another limitation: 15 minutes airtime! i said to the guy in that shop: when he can show me the airtime, we keep the phone - because than the screen seems to work again... )
but no problem they exchanged it against a new one! good service, very customer friendly at o2!
I encountered this one day after getting my unit. I got a replacement. It seems two layers of the touch screen is "stucked" together. Use scotch tape to lift up the area and and the touch screen responds. But the next time you press on the screen it will get stuck again.
So get it changed.
wow
what a great idea... never ever thought of that... *lol* but when you buy such a sophisticated mobile it looks very unsophisticated to lift your screen with scotch-tape everytime you tapped on the screen...
muuu said:
Does it look like this: http://forum.xda-developers.com/showthread.php?p=2557175#post2557175???
Click to expand...
Click to collapse
kinda yes. but not that big and after cleaning phone with a tissue it goes away. i will get a replacement in a few days.. hope this doesnt happen again - but shop told me it seems that there are a few ppl with that problem on td2!! :-(
ok i did get a replacement now and all is fine again. but i think i know what caused the problem.
actually i had the phone always in my back pocket of my jeans. this is not a very good idea when you sit down. the phone gets some pressure on the screen and my screen actually was lowered into the case a little bit. you can see this from the side. that did cause the air under the screen and also the oily liquid that sometimes appeared. so i think the screen felt into the phone case and this was causing the problems. my new phone does not look like the screen is lowered - its totally flat. so i will take more care and not using back pocket of my jeans again to put the phone in
cko2 said:
ok i did get a replacement now and all is fine again. but i think i know what caused the problem.
actually i had the phone always in my back pocket of my jeans. this is not a very good idea when you sit down. the phone gets some pressure on the screen and my screen actually was lowered into the case a little bit. you can see this from the side. that did cause the air under the screen and also the oily liquid that sometimes appeared. so i think the sYcreen felt into the phone case and this was causing the problems. my new phone does not look like the screen is lowered - its totally flat. so i will take more care and not using back pocket of my jeans again to put the phone in
Click to expand...
Click to collapse
I hope you are joking... I mean one can't be serious about carrying a touch screen device in a back pocket of his jeans. Are you even surprised about what happened to it? In fact I'm rather surprised you got a warranty replacement. There is a thing called User manual that comes with the device a it is saying 'Always remove the device from the pocket of your trousers prior to sitting down'. Yu are really lucky indeed you got a replacement....
well aint a mobile phone made for putting in the pocket? this is not my first phone and i never had such a problem even with a touchscreen phone. its not like i did sit on it with full force or something.. just had it in back pocket during cardriving. you can easy do that with any other phone without breaking it...
cko2 said:
well aint a mobile phone made for putting in the pocket? this is not my first phone and i never had such a problem even with a touchscreen phone. its not like i did sit on it with full force or something.. just had it in back pocket during cardriving. you can easy do that with any other phone without breaking it...
Click to expand...
Click to collapse
that's exactly what's it's not - it's a pda phone and it kind of makes sense to treat it differently from normal mobiles which can withstand all sorts of abuse. also if they ask you specifically not to do something because it can damage the device - and you do it and then you are surprised it happened. it's written there for a reason. they surely know that for many people it will be their first pda phone so they don't have much clue how to treat it...
My Xperia is messed up....
Has NO damage... No water damage, hasnt been dropped, overheated or anything...
Last night I was going to respond to a text and slid out the keyboard and the screen went blue... okay...weird... slid it back, still blue. So I restarted it. Heard the "ding" for the power off button. Turned it off. Turned it back on. Started to respond again. Slid it out... No blue screen, just had black and white lines, then went black, but it would never come back to the regular screen.
I have NO idea what triggered this. NONE. I've had no problems with my phone whatsoever.
What I've dont to try and fix it:
-Turn it on and off (obviously, to get the screen back on)
-battery pull
-sim pull
-hard reset
I bought the phone off of EBay. Has no warranty. I got a warranty with Squaretrade for my fiance's cell phone and when he needed to make a claim (it would power off when it was clammed shut...no damage to it. Also you couldnt hear out of the phone at all)) they said they couldnt do anything. I decided that was worthless and that I'm not going to get a warranty with them. Smart move not getting one period, but Ive had bad expierences with them anyways...
What else can I do? I'm @ a total loss... I don't know what else I can do since I've dont the hard reset. I'm trying to avoid taking it to a cell phone repair place b/c I have a hard time trusing people with electronics now (long story) unless I know you.
Thanks for reading and helping if you can!!
Erinc2005 said:
My Xperia is messed up....
Has NO damage... No water damage, hasnt been dropped, overheated or anything...
Last night I was going to respond to a text and slid out the keyboard and the screen went blue... okay...weird... slid it back, still blue. So I restarted it. Heard the "ding" for the power off button. Turned it off. Turned it back on. Started to respond again. Slid it out... No blue screen, just had black and white lines, then went black, but it would never come back to the regular screen.
I have NO idea what triggered this. NONE. I've had no problems with my phone whatsoever.
What I've dont to try and fix it:
-Turn it on and off (obviously, to get the screen back on)
-battery pull
-sim pull
-hard reset
I bought the phone off of EBay. Has no warranty. I got a warranty with Squaretrade for my fiance's cell phone and when he needed to make a claim (it would power off when it was clammed shut...no damage to it. Also you couldnt hear out of the phone at all)) they said they couldnt do anything. I decided that was worthless and that I'm not going to get a warranty with them. Smart move not getting one period, but Ive had bad expierences with them anyways...
What else can I do? I'm @ a total loss... I don't know what else I can do since I've dont the hard reset. I'm trying to avoid taking it to a cell phone repair place b/c I have a hard time trusing people with electronics now (long story) unless I know you.
Thanks for reading and helping if you can!!
Click to expand...
Click to collapse
Search the forum?
All I can find is if the screen is already dead or whatnot....I've already searched before I posted. I didnt want to post a worthless thread.
how long have you own the phone..?
and what rom do you use?...
Arju007 said:
how long have you own the phone..?
and what rom do you use?...
Click to expand...
Click to collapse
Since about March of this year, and ROM--WM 6.1
Go to the service centre and maybe ask them to quote a price, i had this problem
dadeadman said:
Go to the service centre and maybe ask them to quote a price, i had this problem
Click to expand...
Click to collapse
Did yours just happen for no reason?...Out of the blue?
I have this problem on one of mine also....it appears the flexribbon has gone bad...lcd is good....but when the keyboard slides out the screen goes black...tried another board and lcd in the phone problem still persists...this only leaves the ribbon as the culprit.
Regards,
WC
Wild Child said:
I have this problem on one of mine also....it appears the flexribbon has gone bad...lcd is good....but when the keyboard slides out the screen goes black...tried another board and lcd in the phone problem still persists...this only leaves the ribbon as the culprit.
Regards,
WC
Click to expand...
Click to collapse
Ill be sure to tell the people @ the service center what the problem could be. That helps alot. Upsets me that I had to do a hard reset for no reason and mess my phone all up, oh well!
Erinc2005 said:
Did yours just happen for no reason?...Out of the blue?
Click to expand...
Click to collapse
Yup out of the blue
same problem here wildchild is correct its the rigid flex ribbon. unfortunately it will take a month before the parts arrive since its not readily available at Sony Ericsson service centers...
Unfortunately i just got this problem yesterday.
Suddenly, when i slide out the keyboard, screen fades and goes black.
When i slide it back screen is still on but black.
To bring it back i just click power button twice to put it to sleep and wake it up again. I assume this is the same problem and the ribbon cable is loose, correct ??
I was thinking of following one of the disassembly vids to try and open it and make sure the cable is connected correctly.
What do you guys think ? Give it a shot or too risky?
I am not sure if the ribbon cable is damaged and am assuming its just loose because the screen works fine without the keyboard out.
Any advice would be appreciated.
P.S - had the xperia 3 weeks now, bought it used (about 6 months) with no warranty, Its X1i running Energyrom 3.0 (05/08) build.
A month?? Man, that's a long time... geeee wiz. I asked them asn they said about 7-10 busimess days, so we will see... but I trust it'll be about a month since you said they don't have the parts. I shipped it off Friday, put insurance on it, and said a prayer. I hate my Quickfire, its my backup phone... HATE, LOATHE.... DIEEEEE lol.
Ive been searching for other phones to replace this one if i continue to have other problems... but i cant find one I like. i Love WM, the QWERTY, and touch. Felt like i was send my child off to school or something.
I was actually able to find the flex ribbons on ebay took 6 days to get them from china, bought two of them since I have 2 sitting here with the same exact issue....they were about 60 dollars a piece and are here already...will report back after I repair the phones....
Regards,
WC
hey man.. i got the same thing happened to my phone also.. slice keyboard out screen gose black... but phone is still running... why dont chu try the black card in ur box... give them a ring they should help u out... i bought my from ebay also... but lucky is a x1a so in melb which telstra sale it... check urs if is a x1a or not.. it should come with a warranty for 12 months... hope this can help...
I have this also, my pghone is 5 months old. Senrt it away and they didnt have parts. After 3 weeks Sony sent an exchange unit. Opened up the box but the exchange unit is broken! The optical pad doesnt work at all and when I make calls no one can hear me at all..
I had exactly the same problem, besides the regulary cracks
So ive send it in, and a week later ill got a new one. Even with a second battery lol.
The flex cable fixed my issue....so to confirm this is the issue....repaired mine this evening, working perfect, abit tricky to get it all apart but is doable....
Regards,
WC
I got my phone back from Sony on the 9th. They said there was a loose part. I sent it off on Aug 28, and got there on Sept 2, so it didnt take long at all like I thought it would. I was so tired of the other phone. Sad when a phone runs your life haha.
That was such a nice day...went and got fitted for contacts for the first time as well as a getting a new vision rx, came home with perfect vision and what was on my door step, my beloved X1i. I smiled sooooo big. I didnt expect it for a month! They said it should be 7-10 days at the service center though when I called them.
It was still under factory warranty, so I did'nt have to pay for the repair, but I sure would have paid if I had to... lol.
sigh having the same problem now
i used to be excited to put my treo 750 to sleep before when i changed to x1. but apparently i keep taking it out of the box again everytime i have to get my x1 repaired
i just got it back 2 weeks ago when i got fed up with the keyboard button problem.
now it seems i have to bring it back once again since the screen goes blank on me when i slide out the keyboard
hopefully they can fix it on the spot, maybe just a loose connection as compared to a broken ribbon.
was hoping to use the GPS when i go out of the country, paid and got the needed maps already. but i have only a week before i leave. hopefully itll get fixed by then