See No Evil 2.5 ? - Tilt, TyTN II, MDA Vario III General

I just got a Tilt and tried the SNE 2.5. For anyone using it I have a few questions.
My Fn keys don't seem to line up to the keyboard for example
On the Tilt Q has ! on it and W has @ on it. When I do Fn and Q I get @ instead of !. Other keys have this issue as well.
Also I get a rainbow color at the top when in portrait mode.
I can't seem to make voice dialing a side button like I could with my 8525 default ATT ROM.

**This is NOT intended as a flame**
You did not read properly before jumping in head first. Start with the Kaiser Wiki and GWENI linked in my signature.

Arius1 said:
I just got a Tilt and tried the SNE 2.5. For anyone using it I have a few questions.
My Fn keys don't seem to line up to the keyboard for example
On the Tilt Q has ! on it and W has @ on it. When I do Fn and Q I get @ instead of !. Other keys have this issue as well.
Also I get a rainbow color at the top when in portrait mode.
I can't seem to make voice dialing a side button like I could with my 8525 default ATT ROM.
Click to expand...
Click to collapse
just install this and soft reset. It will fix your keyboard settings. bye.

Thank both and I didn't see that wiki. The keyboard is fixed but I don't see anything in the wiki about the rainbow coloring I am having. The voice command that the wiki talks about isn't my issue. Button 6 exists but with this ROM it doesn't list the Voicecommand as a option under all the settings.

Arius1 said:
Thank both and I didn't see that wiki. The keyboard is fixed but I don't see anything in the wiki about the rainbow coloring I am having. The voice command that the wiki talks about isn't my issue. Button 6 exists but with this ROM it doesn't list the Voicecommand as a option under all the settings.
Click to expand...
Click to collapse
post a screen shot of the rainbow coloring you are receiving.

Here you go.

That really isn't a screenshot so I cannot answer the rainbow question because I can hardly see it. Anyhow, I'm sure you searched how to remap button 6. There are a few cab files floating around that will allow you to do that without any issues.

That is a battery status bar.
Take a look at the SNE thread to confirm it.

Sorry try this shot.
It's not button 6 that's the issue it's that voice dial isn't listed as an app that can be applied to button 6.
Thanks jym04 that is what the coloring is at the top. Thank you for pointing it out.
Now if I can figure out why a MMS message isn't downloading and the voice dial I can use this thing.
A side note on the 8525 the 3G icon wouldn't be big like it is in my picture it would always show two arrows saying it's constantly connected. I used the tweaks that are built into the ROM to say always connected but nothing.

with the bar on top of your display (you call it rainbow color) you can watch your battery status. It´s not a bug, it´s a feature
Arius1 said:
Sorry try this shot.
It's not button 6 that's the issue it's that voice dial isn't listed as an app that can be applied to button 6.
Thanks jym04 that is what the coloring is at the top. Thank you for pointing it out.
Now if I can figure out why a MMS message isn't downloading and the voice dial I can use this thing.
A side note on the 8525 the 3G icon wouldn't be big like it is in my picture it would always show two arrows saying it's constantly connected. I used the tweaks that are built into the ROM to say always connected but nothing.
Click to expand...
Click to collapse

Thats the VistaHide battery plugin.

Arius1 said:
Sorry try this shot.
It's not button 6 that's the issue it's that voice dial isn't listed as an app that can be applied to button 6.
Click to expand...
Click to collapse
Create a shortcut to voice dial in your Start Menu (or subdirectory therein). Then it will appear as an app that you can apply to buttons.
I got flamed for asking a similar question (different app) and I couldn't find an answer through search either.

Thank you Exitao!

Wow proud to see ppl still flashing my ROMS...

Related

T-mobile Wing Mod Requests :)

hello all, i have a couple requests (most likely has to do with registry editing)
1: Hide the top bar (time, and stuff)
2: Have a big invisible x button to close programs (no need for stylus)
3: Hide bottom bar (calendar/contacts) but still be able to use the soft keys to access them
thanks a bunch in advanced
nice request
those are some nice request. but if someone even tries to cook this rom then we should think of giving them a donation for their work dont you think?
persianprez said:
hello all, i have a couple requests (most likely has to do with registry editing)
1: Hide the top bar (time, and stuff)
2: Have a big invisible x button to close programs (no need for stylus)
3: Hide bottom bar (calendar/contacts) but still be able to use the soft keys to access them
thanks a bunch in advanced
Click to expand...
Click to collapse
As taken from my guide:
Can I get rid of the "Contacts / Calendar" bar?
Dcino Bar is a great app to get rid of it. Simply place this app in your Windows/Startup folder, you can download it Here
Click to expand...
Click to collapse
you can still use the keys on the phone to access the "contacts or calendar"
thx a lot tyler, it worked great, is there anyway to make it invisible for all programs as well?
One of the Rom Cookers need to keep these ideas in mind...
Maybe have a version out which is fully powered by the touch cube and pocketCM default. Its becoming more smoother to use as a regular phone and I can see my calendar on the main screen!!!
i actually prefer a software solution rather than loading a new rom
megaman81 said:
One of the Rom Cookers need to keep these ideas in mind...
Maybe have a version out which is fully powered by the touch cube and pocketCM default. Its becoming more smoother to use as a regular phone and I can see my calendar on the main screen!!!
Click to expand...
Click to collapse
The author of pocketCM asks that it not be included in ROMs.
Ugh... yes! I want a big x button so I don't have to turn my finger and slide it up in the corner to hit the x.
WM5 on the older PALM devices have the X button moved to the left so it's not up against the edge; can we do that on the thing by editing the registry somehow?
kraftey said:
Ugh... yes! I want a big x button so I don't have to turn my finger and slide it up in the corner to hit the x.
WM5 on the older PALM devices have the X button moved to the left so it's not up against the edge; can we do that on the thing by editing the registry somehow?
Click to expand...
Click to collapse
finally some1 who feels my pain lol, taking out the stylus just to hit the x annoys me
bump, still want that big invisible x =]
Maybe this will help:
http://forum.xda-developers.com/showthread.php?t=386378
Or papamopps rom... been using it for the past week and love it.
http://forum.xda-developers.com/showthread.php?t=396036
kraftey said:
Ugh... yes! I want a big x button so I don't have to turn my finger and slide it up in the corner to hit the x.
WM5 on the older PALM devices have the X button moved to the left so it's not up against the edge; can we do that on the thing by editing the registry somehow?
Click to expand...
Click to collapse
I use FTouchSL to do this. I made the top left active corner a close option so it closes the application thats open. You can set how many pixels it is & the amount of time it takes to activate. It works perfectly
Beast84 said:
I use http://www.ftouchsl.com to do this. I made the top left active corner a close option so it closes the application thats open. You can set how many pixels it is & the amount of time it takes to activate. It works perfectly
Click to expand...
Click to collapse
This looks really tight, ima try it out, I dont feel like going through the whole rom thing again, im sticking to manufacturer settings, although i might change the pool size thing again

Batti Program

Hi all,
I recently added a battery bar program called Batti2.1. It is a really great program and i like it a lot. There is, however, one small bug...
When using the program it remaps the Calendar soft key to "Notification". Rather it does not remap it but always displays the "Notification" word. I guess this is so because it gives me a setting asking me if i want the battery indicator in the top bar (which is what i want). When i click on the notification icon it gives me detail about the battery etc. When i am done and click on hide, it goes back to saying "Notification".
When i recieve an sms or missed call, it then resets the soft key back to the original "Calender" and does not come up with the "Notification" key i usually get when i have a missed call or sms notification.
Is there a registry setting to disable the batti program's notification icon or am i stuck with this for good (so long as i have the program installed)??
Has anybody else used this program? Had this same problem? It is a really good piece of software and does not affect anything else.
Can anybody help please. I have included screenshots and attached the batti file incase anyone is interested in looking at this useful program.
yep...that happens...i remember when i used that program...get...um...damn i cant remember the name of the program i used..
Novice Gadget Boy said:
Hi all,
When using the program it remaps the Calendar soft key to "Notification".
Click to expand...
Click to collapse
Wow... that is annoying. Nice program, but I see your dilemma.
Whenever there's a notification (such as wi-fi detected), the left soft key is remapped to it. PocketPlayer does that on mine. I don't mind because I can use the today screen plugin to access the calendar.
Use VistaHide battery gauge instead.
Thanks to those who replied.
Tinkering around with the program i discovered a solution. In settings option set the following settings:
<PLEASE SEE IMAGE CAPTURE NUMBER 3 IN THE ATTACHMENTS>
I then click ok and hide the diolog box (hide button). The notifiaction and icon on the top bar are gone. However, there is a small bar right on the top of the top bar with graduations along it. This is the battery bar and each graduation represents 5%. When you tap this bar once, the notification box comes up and displays all the info. When you tap on hide, it all goes away. No more remapping.
Thanks to those who tried to help out.
batti 2.4 is out but the sounds portion doesnt work on the touch pro ... plays the sounds at random rimes
http://code.google.com/p/batti/
very nice work...
perfect for my touch pro.. i didn't check the sounds part, but i'm not interested right now..
i'd like to have a button in programs tab to open the view information page... can someone give me some help?
respect!

Kaiser Dialpad changing to Status page

Does anybody know how to change the setting for the dialpad during a phone call? I need to have the dialpad on all the time, even during a phone call.
Thanks.
EagleClaw said:
Does anybody know how to change the setting for the dialpad during a phone call? I need to have the dialpad on all the time, even during a phone call.
Thanks.
Click to expand...
Click to collapse
Hi,
KaiserTweak can do it:
Call -> disable both "Fast Sleep" and "Sleep" options!
Try this great application, with many other tweaks!
PS: Nex time, however, use better the forum "search" feature!!
Ciao
Thanks for your help. But I have KT installed and the first two settings are disabled. The only thing it did was solve the phone going black after 10 seconds. My dialpad is still replaced by the status page. And I need to have the dialpad up all the time.
I also check the registry settings that KT changes, and they were changed. So I don't know if this is an issue with my phone or all Kaisers.
Any registry tweak that you know?
oh, i get it........you mean the keypad dont you?
EagleClaw said:
Thanks for your help. But I have KT installed and the first two settings are disabled. The only thing it did was solve the phone going black after 10 seconds. My dialpad is still replaced by the status page. And I need to have the dialpad up all the time.
I also check the registry settings that KT changes, and they were changed. So I don't know if this is an issue with my phone or all Kaisers.
Any registry tweak that you know?
Click to expand...
Click to collapse
Ok, sorry, but i didn't well understand your bug, or requirement!!
What do you mean for "Status page"??
Can you post some screenshot?
Sorry, again, dude
don't need screenshots, i understand now!
But only one question: after you start a call can you tap the left softkey and show the dialpad? if so, you would like to always show the dialpad tab, and not the status page, also when the call start without pressing any key, right??
@[email protected] said:
Sorry, again, dude
don't need screenshots, i understand now!
But only one question: after you start a call can you tap the left softkey and show the dialpad? if so, you would like to always show the dialpad tab, and not the status page, also when the call start without pressing any key, right??
Click to expand...
Click to collapse
I believe this is exactly what he meant, and I for one would like to know also.
Dom; that's exactly what I meant. 99% of my calls I make through my pbx, and because of that, I need to keep inputing numbers. The fact that I need to click on the "show keypad" on every call is annoying and dangerous (when I am driving). Yes, the show key pad is on the left corner, but it would be more convenient to have it on all the time, and when and if I need the status page, I would press the show status page button.
I am sorry I was not clear on my first post.
Thanks.

BackLight brightness adjust command line utility for Kaiser aka TYTN II

I dunno if I'm only one who has this problem but when I'm occasionally on sun I can't see nothing on my Kaiser and it's really difficult to setup backlight brightness on touchscreen which u can't see.... So I've been looking alot if there is some utility which I can link with button or gesture and I haven't found anything... So I've wrote my own utility. Feel free to use it as well if u find it useful -> http://lobster.ic.cz/?page=bl
is this useful or is there easier way to do that??
Been searching for an app like this for a week.
Works great!
Thanks.
Here's another program that gives you a today plug in for it:
http://forum.xda-developers.com/showthread.php?t=412896
I'll b trying yours tho as I like the idea of UL with icons for up and down
Cheers,
Matthew
I made a cab with this program mapped to the PTT button. I have a AT&T Tilt, Im not sure if your phone has a PTT button or if its called something else or whatever.
With this, just run the cab then I tap the button and it changed the brightness really quickly, no menu or anything, I love it! If I walk out into the sun I just tap the button 3 times and my screen is bright.
Lobsterii, I love this program thanks a ton!
I'm glad that I could helped u out guys... actually there might be more funny stuff possible only if HTC release some documentation on theirs DLL files cos it's pain to guess arguments...
you did it all by guessing? I figured you would have decompiled the dll.
Truly excellent! I have also been looking for something like this for a long time.
I figured I might as well kick off the feature requests that always follow a new release: How about the option set both battery and power brightness with one command? Perhaps by a special switch, or by only specifying the brightness level (i.e. no 'b' or 'p' switch)? Or is there a way to do it already?
Thanks again for a useful app!
you did it all by guessing? I figured you would have decompiled the dll.
Click to expand...
Click to collapse
I've read some forum where someone pointed out that backlight function should be in some dll by HTC dunno where it was... Then I was googling "dll find export function" and I've found prog "DLL Export Viewer" which can show function names in dll. Unfortunatelly there is generally impossible to find out how many/what arguments the function has. So I've found function name like HTCUtilSetOnBatteryBrightnessLevel and I've simply try prototype int HTCUtilSetOnBatteryBrightnessLevel(int); but it crashed... so I keep going like int HTCUtilSetOnBatteryBrightnessLevel(int*); and it worked... voila...
pudifoot said:
Truly excellent! I have also been looking for something like this for a long time.
Click to expand...
Click to collapse
thx alot...
I figured I might as well kick off the feature requests that always follow a new release: How about the option set both battery and power brightness with one command? Perhaps by a special switch, or by only specifying the brightness level (i.e. no 'b' or 'p' switch)? Or is there a way to do it already?
Click to expand...
Click to collapse
done. + it's now compiled as an release version so it actually has 50KB less than old version... enjoy it's at the same place instead original files http://www.lobster.3web.cz/bordel/bl/index.htm...
Nice improvements! how about another a switch so that it will toggle between brightest to dimmest? So if this was used it would just go between 1 or 10 and none in between.
Thanks for implementing the feature I was looking for. A perfect application - it's small and fast, and it gets the job done with excellence.
Thank you. Works perfectly.
silentanvil said:
Nice improvements! how about another a switch so that it will toggle between brightest to dimmest? So if this was used it would just go between 1 or 10 and none in between.
Click to expand...
Click to collapse
hmhm... what I wouldn't do for y... There is new version 02 (on my web at the same place) where u can setup your own sequence. Length of sequence might be from 1 to 10... values are as usual from 0 to 9... But numbers must not repeat (known feature I don't see point to solve it) so u can set something like "bl02.exe 0 5 1 9 3" or whatever else... enjoy
Report any found bugs... I mean it's super simple but it's 4 am so I'm half sleeping...
lobsterii said:
hmhm... what I wouldn't do for y... There is new version 02 (on my web at the same place) where u can setup your own sequence. Length of sequence might be from 1 to 10... values are as usual from 0 to 9... But numbers must not repeat (known feature I don't see point to solve it) so u can set something like "bl02.exe 0 5 1 9 3" or whatever else... enjoy
Report any found bugs... I mean it's super simple but it's 4 am so I'm half sleeping...
Click to expand...
Click to collapse
Awesome! Thanks so much! I've also been looking everywhere for something like this!
Awesome!
Well done! I've been looking for ages for something to do this.
How to use bl02...
Something from lobsterii that helped me:
create link in Total commander (file manager) I think its in options "File -> >>>>> -> Create shortcut" then I have another file bl02.lnk then I open properties of the lnk file, I click tab shortcut and put the text of path into "" and after it I wrote parameters so it looks like
"\Program files\bl\bl02.exe" 1 3 9
OK dumb question and first time posting so don't slaughter me. If I understand the thread correctly this will put large buttons to adjust from the Backlight screen....correct? Is there a program (other than the PTT button which I'm using) that will allow a button or swipe to adjust the brightness without having to open the brightness display? If you get far enough to open the utility then its not that hard to move the brightness up. Sorry for the dumbness of the question.
volleykinginnc said:
If I understand the thread correctly this will put large buttons to adjust from the Backlight screen....correct?
Click to expand...
Click to collapse
my bl02.exe doesn't put any button anywhere... it's just app which actually toggle brightness. U can try to run it via file explorer it should change brightness...
volleykinginnc said:
Is there a program (other than the PTT button which I'm using) that will allow a button or swipe to adjust the brightness without having to open the brightness display?
Click to expand...
Click to collapse
There is plenty of programs to map this app to buttons, finger swipes and some other crazy stuff like voice commands etc.. For example I'm using FTouchFlo (u can use FTouchSl which is easier to configure) and map backlight change for finger swipes... Most easy way is just copy blXX.exe to /Windows/Start Menu/Programs/blxx.exe and then go to Start->Settings->(tab)Personal->Buttons and link it with some buton...
I'm just now at work so have no time for more explanation... but Once I get home I'll create some FAQ at download page cos... cos it'll be easier for all of us
dont sweat it that was a perfect explanation and I now have it helped me to get it running to a button.
One other quick question though....I have S2U2. So the button doesn't work until I have unlocked it (which sometimes is hard to see going out to daylight) is there any way (easy way, Im no programmer)to allow the button to work (that is brighten the display via the button I have it mapped to) while it is still locked?
volleykinginnc said:
dont sweat it that was a perfect explanation and I now have it helped me to get it running to a button.
One other quick question though....I have S2U2. So the button doesn't work until I have unlocked it (which sometimes is hard to see going out to daylight) is there any way (easy way, Im no programmer)to allow the button to work (that is brighten the display via the button I have it mapped to) while it is still locked?
Click to expand...
Click to collapse
I'm sure he won't be able to bypass A_C's S2U2, but (assuming you have a Kaiser, you didn't say) if you enable dpad in S2U2 you can always hold your right dpad button to make sure S2U2 is unlocked, even if you can't see the screen, and then hit the button for the "bl02.exe 9" link.
Ha ha...you guys are awesome! Right Dpad enabled and now it works like a charm even in the brightest sun!! Thanks for the great application...makes a big difference in usability.
Some of you experts ought to make a list of these application gems (this program/kaeser tweaks etc) to make it easy for the noobs like me. This is good stuff!!

AT&T Tilt - SMS typing box behind bottom curtain

I'm running Josh's WM 6.5 release and my SMS screen shows the typing box behind the lower curtain (Reply/KB/Menu). On my last rom (Phoenix II 6.1), there was a .CAB fix that took care of that problem on Tilts specifically, but I can't remember what it was. What was it?
--RC
A problem so nice, he had to post it twice!
ChumleyEX said:
A problem so nice, he had to post it twice!
Click to expand...
Click to collapse
Lol and i still never understood
Quick fix
if the box is too small or isn't visible to your liking, try clicking on the keyboard button to bring out the SIP, then again to hide it. When txting in landscape mode, sometimes the box is too small and doesn't properly use the scroll bar on the side. This has managed to fix the problem for me....till it comes back a week later
ChumleyEX said:
A problem so nice, he had to post it twice!
Click to expand...
Click to collapse
sorry, some kind of forum burp.
zyphuris55 said:
if the box is too small or isn't visible to your liking, try clicking on the keyboard button to bring out the SIP, then again to hide it. When txting in landscape mode, sometimes the box is too small and doesn't properly use the scroll bar on the side. This has managed to fix the problem for me....till it comes back a week later
Click to expand...
Click to collapse
thanks, that seems to have done it.
--RC

Categories

Resources