Database Develop

ActiveSync connect problem after flashing..

Hi, I flashed my Herald with WM6 ROM by ASerg, and it fails. Now after hardreset it loading only white screen with some beep (after startup screen with logo) and thats all.......my problem is simple - I can go to bootloader mode, but in bootloader, when i want to re-flash to another ROM, i can't connect it with PC. It showed USB in bootloader screen, but activesync dont want to synchronize and every flashing method showin' warrning NO DEVICE CONNECTED. i know, that herald is connected, pc warned me by beep that new hardware is connected, bud activesync no....how can i fix it ? please help.....thx

P.L said:
Hi, I flashed my Herald with WM6 ROM by ASerg, and it fails. Now after hardreset it loading only white screen with some beep (after startup screen with logo) and thats all.......my problem is simple - I can go to bootloader mode, but in bootloader, when i want to re-flash to another ROM, i can't connect it with PC. It showed USB in bootloader screen, but activesync dont want to synchronize and every flashing method showin' warrning NO DEVICE CONNECTED. i know, that herald is connected, pc warned me by beep that new hardware is connected, bud activesync no....how can i fix it ? please help.....thx
Click to expand...
Click to collapse
Try to falsh with RUU - it should work without active sync. Because in bootloader it connects BUT not via activesync.
Good luck

papamopps said:
Try to falsh with RUU - it should work without active sync. Because in bootloader it connects BUT not via activesync.
Good luck
Click to expand...
Click to collapse
Dear user
I have same problem
I try via RUU
but the problem not solved !
how can i do?
Thanks

flash interupted

was flashing and some one caused a communication error- . tried to recovery but was unsuccessful, now iall i see is run, green, blue, and white. is this what you called bricked. what can i do???

No, it is not bricked, with a bricked Wizard you can't either charge or power on it.
Just get another computer with ActiveSync installed (preferably a Notebook computer), and try RUU again.
And MAKE SURE you have already CID-unlock (NOTE: CID unlock is NOT SIM unlock) before flashing custom ROMs, otherwise follow the stickies to flash the Button's ROM and unlock it before proceed.

help
how can i try RUU????
i´ve also my 9100 with 3 colors , but when i connect to activesync they don´t recognize it.
how can i turn on again my 9100?
thx
hugo

hugomalheiro said:
how can i try RUU????
i´ve also my 9100 with 3 colors , but when i connect to activesync they don´t recognize it.
how can i turn on again my 9100?
thx
hugo
Click to expand...
Click to collapse
Activesync doesn't work in Bootloaders (multi color screen),but you can flash the phone in Bootloaders mode.While in Bootloaders (Multi color screen),hook your phone with pc via usb cable and watch small usb appear at the bottom of the Bootloaders mode,it confirms connectivity with pc and run the RUU in the Rom ,it'll start to flash. Let it complete and phone will reboot and start to work normal.

I´ve tried several times to run the RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 but the application says that there isn´t no phone connected.
what i´m i doing wrong?
thx

HELP!!My Xperia flash get problem!

I been study whole day in the forum also didnt found anyone fail in flashing Xperia X1.
I got a Xperia X1 accidentally flash rom without flash to HardSPL.
Now the phone is power on just will goto the BootLoader mode (TriColour Screen),
But if i plug in the USB cable connect to PC then it will goto normal.Must every time need to do that way only i can use Xperia X1.And the bigger problem is when i plug in the USB cable the X1 and PC wont be connect and even i can't charge battery also.Because of the failure connection by USB i totally can't flash X1 by USB.
I really need help in this problem,hope anyone or any ROM maker help me this problem.
THX....

Try to flash your phone again with a stock rom (you can find it in the rom section) using the SDcard method

I been try to flash the stock rom UK R1AA0017 and UK R2AA010 the problem still remain.Any other idea?Anyway thank you Mopral helping me.

hao_nam1 said:
I been try to flash the stock rom UK R1AA0017 and UK R2AA010 the problem still remain.Any other idea?Anyway thank you Mopral helping me.
Click to expand...
Click to collapse
try and use the sd card method to flash a stock rom..since your phone is booting the bootloader it shld be able to pick up the rom, hope u get it fixed

While in the boot loader (tricolour screen)
- Copy your RUU_Signed.nbh ROM file to the CustomRUU folder (where you have ROMUpdateUtility)
- Run "ROMUpdateUtility.exe"
- Connect your phone to the PC, text at bottom in tricolour screen will change from Serial to USB
- Follow on-screen instructions, loading bar shows on PC & phone

lakeside00
I been try to flash the stock rom by sd-card,problem remain only.
Musse_1
Friend my problem is i totally can't connect my phone in pc.No connection between them.That why i only can use sd-card to flash.
Guys i been flash R1AA0017 and R2AA010 rom in my phone by sd-card also can't work,problem remain.

No PPL willing to help me about my problem?

Can i asking a stupid and crazy question?
Can i flash Hard-SPL by SD-Card?
Will any things happen if i use this way to flash Hard_SPL?
Plz get someone give me a idea about my case.....

you can try but as your own risk.
extract the kovsimg.nbh to sd card root directory
HSL_SD_download

Sudden black out

everytime i try to upgrade my xda alpine which is connected to the computer thru usb craddle, it suddenly turn off n went to bootloader mode....what is the prob??? help pls pls...

now i think it goes into bootloader mode after autoconfig!!! when it ask for autoconfig, no matter i choose yes or no, it wil go into bootloader mode!! help!!!

ronan_chai said:
now i think it goes into bootloader mode after autoconfig!!! when it ask for autoconfig, no matter i choose yes or no, it wil go into bootloader mode!! help!!!
Click to expand...
Click to collapse
should have before you upgrade, remove the sim card first ...!!! ​ you try to upgrade with an official ROM for your device ​ for the ROM you can find it at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Alpine

No...i didnt have my sim card inside when i upgrade...and now it wil go into bootloader mode right after autoconfiguration...and it also go into bootloader mode halfway upgrading...and lost connection with the computer...so i cannot upgrade or flash it back to original rom...what sud i do??

ronan_chai said:
No...i didnt have my sim card inside when i upgrade...and now it wil go into bootloader mode right after autoconfiguration...and it also go into bootloader mode halfway upgrading...and lost connection with the computer...so i cannot upgrade or flash it back to original rom...what sud i do??
Click to expand...
Click to collapse
try to hard reset the device , this is her guide HTC Alpine hard reset
To perform a full reset
A full device reset clears memory, deletes all data, and restores the Pocket PC Phone to its default settings. Programs installed at the factory remain. All data that you have created and programs you have installed are erased.
Press and hold the Power button, and then use your stylus to press the “soft reset button” at the same time, as shown below. Be sure you have backed up all your data on an SD card or on a desktop PC before performing a full reset. after you hard reset the device, connect to a USB sync and you Flash Room again All you have to remember, allow usb connection .... and not disabled its usb connection Okey ​if you still have problems you can contact me​

Do i need to go into bootloader mode first before flashing?? Cause what i did was, connect it the comp, and while it is stil connected with windows mobile device centre and the phone is still in windows mobile desktop, then i run the MaUpgradeUt_noID.exe, and halfway upgrading, it just turn off n go back to bootloader mode...and then after that, it auto black out after each autoconfiguration.
And by Flash Rom, do you mean just run the MaUpgradeUt_noID.exe with all the files in it?? or there is something else i should do???
Sorry for my ignorance And ur guidance will be very much appreaciated!!!!

ronan_chai said:
Do i need to go into bootloader mode first before flashing?? Cause what i did was, connect it the comp, and while it is stil connected with windows mobile device centre and the phone is still in windows mobile desktop, then i run the MaUpgradeUt_noID.exe, and halfway upgrading, it just turn off n go back to bootloader mode...and then after that, it auto black out after each autoconfiguration.
And by Flash Rom, do you mean just run the MaUpgradeUt_noID.exe with all the files in it?? or there is something else i should do???
Sorry for my ignorance And ur guidance will be very much appreaciated!!!!
Click to expand...
Click to collapse
Windows mobile device centre?--Seems to be the Vista/Win7 driver problem. Search for it, using the Search button.
Flashing with Win7/32bit or Vista

muckelmaus said:
Windows mobile device centre?--Seems to be the Vista/Win7 driver problem. Search for it, using the Search button.
Flashing with Win7/32bit or Vista
Click to expand...
Click to collapse
EnterBL.exe should reboot the device into bootloader only, Activesync should disable then. You can access bootloader manually, it's more safe

Now i managed to get into bootloader mode and upgrade it.. but the upgrade hangs halfway, the progress stays at 0% and saying it's upgrading radio, but always failed. What's should i do pls?

ronan_chai said:
Now i managed to get into bootloader mode and upgrade it.. but the upgrade hangs halfway, the progress stays at 0% and saying it's upgrading radio, but always failed. What's should i do pls?
Click to expand...
Click to collapse
remove the battery from the device and wait until 10 minutes, then plug it in again and make sure your device go to the bootloader to reflash
next time before you perform the upgrade whether you've unlock device ??

[Q] HELP: Stuck in bootloader or no USB

Hi All,
from one moment to another my X1 decided to boot into bootloader mode.
The strange thing is however, that when I connect it to the USB of my PC and reset the X1, it boots normally. Well, almost normal as the USB doesn't seem to be working.
I flashed the rom to APP-SW_X1_GENERIC_UK_1213-6450_R3AA010__KOVS using the SDCard and that worked without a problem. But still the X1 boots into bootloader mode (except when connected to the PC).
I tried a hardreset, pressed the volume down button several times (to make sure it isn't stuck), tried to use MTTY (but that doesn't show a prompt), but nothing seems to help.
Is there anyone who can help me with this, because I'm out of ideas....
Update:
I managed to boot the OS (USB connected) and install HSPL using Xperia-SSPL-Manual. This succeeded and I now have SPL-0.78.OliNext. I flashed the phone to a new ROM (826x_KOVSKY_29017_2021), and that succeeded as well. It didn't solve my problem however. I still get the bootloader screen when I start the phone and can only start the OS by starting with USB connected...
Update2:
Yesterday evening I took the whole phone apart to make sure no buttons are/were stuck. Didn't find anything, put it back together and it still boots into bootloader.
I also managed to get a connection to the phone using NueTTY. I executed command Set 14 0, restarted the phone...and still it boots into bootloader.
If there is any one who knows of something that I haven't tried yet, PLEASE let me know....

same problem,,if there's a way to flash recovery from sd card in fastboot mode,,that'd be great

kldahmd said:
same problem,,if there's a way to flash recovery from sd card in fastboot mode,,that'd be great
Click to expand...
Click to collapse
Flashing the ROM is no problem, I can put every ROM on it that I like. But even after flashing the ROM the phone still starts in bootloader....

You can try to go into the bootloader on ur pc and use recovery.bat with fastboot.

xvink said:
Flashing the ROM is no problem, I can put every ROM on it that I like. But even after flashing the ROM the phone still starts in bootloader....
Click to expand...
Click to collapse
hi, I'm kind of having the same issue as you do..can you please be of help and tell me how did you manage to HSPL it to 0.78.OliNex?
Correct me If I am wrong, but you must copy Xpera_SSPL_Manual. exe on X1, run it from file explorer and then run X1_HardSPL.exe on your PC, whlie X1 is connected via usb (although mine also doesn't recognize the X1) ?
i would really apreciate it... thnx

i have the same problem guys, did anyone of you found any solution for this?

same problem
Have you tried to do a task29 with KovskyAdvancedRUU?