Hello all, while drunk at the beach this weekend I accidentally went into the water with my Touch Diamond in my pocket... stupid... I know, did I mention I was drunk? Anyways, the current issue at hand is what to do with my screwed up cell phone.
I took the backing, battery and SIM card out of the phone and let it dry out as much as I could since the weekend. When I turned it on this morning, the "smart mobility" text appears for a few seconds, but the phone shuts off shortly after that. Do batteries usually break from water damage, as well?
If anyone has any advice for me I would greatly appreciate it. Does anyone know of a legit place that can repair this? Is there anything I can do to try and remedy this problem? Or would you recommend I just sell/ditch this one and get a new phone? Thanks a lot.
Have you tried charging the battery? that might explain it only booting for a second, the other explanation is that it's fried the ROM chips and only the bootloader works.
It's not looking good, is it under warranty?
Disassemble your Diamond completely (manual floating around somewhere in this forum), clean all pieces using one of these isopropanol-brush-thingies, reassemble, turn it on - and pray. Any year - a new battery might be a good idea. No promises on anything of that though. The diamond is a very integrated piece of technology and you might have short-circuited something on one of the PCBs really. No guarantee that everything will work as usual even if the device comes up as well.
Warranty seems to be out of the question - I guess virtually any repair center will notice residue of loads of salt water on the first look inside...
That's true, I meant to say insurance, heh.
Strip it down Salt water is very and I mean very corrosive ! You have nothing to lose and everything to gain by doing this . Waranty repair will be expensive.
Clean with an alchol based cleaner as advised but you must ensure you get all the salt out. To see it boot means that the screen has survived ( Amazed by this ) .
Best of luck , oh and if it does not work are you insured for accidental damage on personal items on your household insurance. This could be the next route
I have the same problem with my Tytn 2. It got wet during the "Oranje" Party in Basel, when the firemen were "cooling" down the fans...
It boots..but as soon as it has booted, you here a lot of "bling..bling..bling.." and it shuts down.. the batterie doesn't charge..
You recommend to open and clean it with alcool? Actually I'm not sure if it was washed by the firemen or by my own alcool .ehhehe..
I have a Diamond now, but if I get it back to work, I would sell it on ebay.
Regards
dajudge01 said:
Warranty seems to be out of the question - I guess virtually any repair center will notice residue of loads of salt water on the first look inside...
Click to expand...
Click to collapse
There is a watersensor inside the diamond. They'll notice that the device has been in the water.
wardy said:
Strip it down Salt water is very and I mean very corrosive ! You have nothing to lose and everything to gain by doing this . Waranty repair will be expensive.
Clean with an alchol based cleaner as advised but you must ensure you get all the salt out. To see it boot means that the screen has survived ( Amazed by this ) .
Best of luck , oh and if it does not work are you insured for accidental damage on personal items on your household insurance. This could be the next route
Click to expand...
Click to collapse
Luckily I was at lake Michigan in Chicago (fresh water), for whatever that's worth, so I'm not really worried about salt corroding anything away. I bought it off eBay unlocked, I did buy insurance but, naturally, I'm pretty sure that this water damage won't be covered.
Sounds like taking it apart and cleaning it might be my best bet. Do you guys think that any cell phone repair place would be able to help me out? Anyone know of a good cell phone repair shop (in the U.S.)? Thanks for the help thus far guys, I really appreciate it
Firstly remove the battery and SIM, please do not try to power up or charge again as you might have already damaged it beyond repair.
Isopropanol or IPA is what you need (100% Alcohol), you can get this from your local chemist for about £5 a bottle.
You need to strip your phone down completely and use an anti static PCB brush to clean the whole lot (Buy it from Maplin), submerge it in a plate of IPA (excluding the screen) while cleaning. As for the warranty sticker remove this by first heating with a hair drier, then uing a Stanley knife point to remove it.
Once it’s all been cleaned and dried in air, re-assemble and power up. If it fails to work take it back for a warranty replacement. As the warranty sticker is intact, and all the evidence of water damage will have been removed, they should replace it for you without a problem.
nairb011 said:
Luckily I was at lake Michigan in Chicago (fresh water), for whatever that's worth, so I'm not really worried about salt corroding anything away. I bought it off eBay unlocked, I did buy insurance but, naturally, I'm pretty sure that this water damage won't be covered.
Sounds like taking it apart and cleaning it might be my best bet. Do you guys think that any cell phone repair place would be able to help me out? Anyone know of a good cell phone repair shop (in the U.S.)? Thanks for the help thus far guys, I really appreciate it
Click to expand...
Click to collapse
Pretty sure? I would check if I was you before doing anything else with it. If insurance doesnt cover water damage, what does it cover? Phone insurance is so expensive i thought they covered everything like theft and accidental damage, I thought the idea was a warranty wont cover you if you break the phone but insurance will.
I'm thinking it may be an idea to check before you do anything else so they dont say "Well we cover water damage, but now youve taken apart the phone we cant cover you"
Antimus said:
Have you tried charging the battery? that might explain it only booting for a second, the other explanation is that it's fried the ROM chips and only the bootloader works.
It's not looking good, is it under warranty?
Click to expand...
Click to collapse
Seriously you are not hoping warranty will cover "swimming with the diamond"...
imranbashir_uk said:
all the evidence of water damage will have been removed, they should replace it for you without a problem.
Click to expand...
Click to collapse
All the evidence, that is, apart from the water-sensitive tab which I am assuming you didn't know about...? (behind the tab for attaching a strap)
Mathew
webmice said:
Seriously you are not hoping warranty will cover "swimming with the diamond"...
Click to expand...
Click to collapse
or doese he mean "Swimming Diamond" ... Is that a new feature we overlocked? I think it's time for another entry in the tweaklist... *rofl*
My warranty does not cover accidental water damage, that is for sure.
I charged the battery up over the weekend and tried turning it back on, and, to my utter amazement, the phone completely powered on. I got to all of my menus and was able to use all of the programs that I opened, even the WiFi worked.
However, the functionality of the touch screen is quite screwed up. I don't know if its shorting out or what but there are basically "ghost taps" and other unintentional actions happening all the time. For example, if I were to just leave it at the home screen it would eventually scroll to another menu, open the start pull-down menu, automatically open the calendar and start doing random ****, etc.
Does anyone know how to fix the touch screen or have any ideas on how to replace one? I have a faint hope that this thing might not be beyond saving.. thanks a lot people
nairb011 said:
Does anyone know how to fix the touch screen or have any ideas on how to replace one? I have a faint hope that this thing might not be beyond saving.. thanks a lot people
Click to expand...
Click to collapse
Maybe try to re-calibrate the touch screen?
Don't give up hope, sometimes these things can take days, even weeks to fully dry and become functional. My mom had a sony ericsson somethingorother that she loved, dropped in the tub, didn't work for like a month or more... She'd check it every week or so to see, and slowly the features started coming back... Little by little, more and more buttons would respond (without activating 2 or 3 at a time). Well, long story short (too late?) works 100% now. I don't think water damage is a reparable occurrence, but DON'T sell your Diamond for parts or anything like that, keep it around and check back periodically. Best of luck.
there is a little white sticker onto the battery.
If it goes RED it shows HTC that the Phone/Battery went into the water.
This allows HTC to avoid repair "sunk" phones
deuillevent said:
there is a little white sticker onto the battery.
If it goes RED it shows HTC that the Phone/Battery went into the water.
This allows HTC to avoid repair "sunk" phones
Click to expand...
Click to collapse
Should also be one on the phone... If not, there's your solution. New battery + deny any water damage = Free replacement.
Black93300ZX said:
Should also be one on the phone... If not, there's your solution. New battery + deny any water damage = Free replacement.
Click to expand...
Click to collapse
See post #12
Haha you're all over it... Yeah, I had a feeling they'd have something in the phone, they'd never make it THAT easy.
Related
This question is directed to those who have taken apart their Kaiser, and specifically screen the screen assembly. I've got water issues and the screen is broke now. Here's the story. I might get some outrageous warranty charges.
I installed the InvisiShield (www.shieldzone.com) on my phone. Essentially it's a screen protector that is indestructible. It practically is, but unfortunately it destroyed my phone. To install it you have to spray this liquid on the back of the 'shield' and apply it to your phone, using a squeegee to get the bubbles out. It went pretty well, and I was happy with the results, but 3 days later my screen stopped working.
Everything is washed out, and it looks like water got inside the LCD somehow. For instance, colors streak across the LCD in fonts, etc.
I called ATT and they are mailing a replacement, and I'll be expected to send this phone back. They said if the return phone has damage that would void warranty (water damage, etc) I'll be prorated $400 on my next bill.
Over the phone the customer representative had me remove the battery and check one of the water damage pads to make sure it was white. It is.
For those who have seen internal phone assembly, is there any of these directly by the screen that will pick up moisture?
As far as ATT knows, the phone LCD suddenly stopped working. I'll get a replacement and /hopefully/ theres not a moisture pad right next to the LCD assembly. Anyone know?
Damn, hate those broken screen story's. Scars the **** out of me.
jon_k said:
This question is directed to those who have taken apart their Kaiser, and specifically screen the screen assembly. I've got water issues and the screen is broke now. Here's the story. I might get some outrageous warranty charges.
I installed the InvisiShield (www.shieldzone.com) on my phone. Essentially it's a screen protector that is indestructible. It practically is, but unfortunately it destroyed my phone. To install it you have to spray this liquid on the back of the 'shield' and apply it to your phone, using a squeegee to get the bubbles out. It went pretty well, and I was happy with the results, but 3 days later my screen stopped working.
Everything is washed out, and it looks like water got inside the LCD somehow. For instance, colors streak across the LCD in fonts, etc.
I called ATT and they are mailing a replacement, and I'll be expected to send this phone back. They said if the return phone has damage that would void warranty (water damage, etc) I'll be prorated $400 on my next bill.
Over the phone the customer representative had me remove the battery and check one of the water damage pads to make sure it was white. It is.
For those who have seen internal phone assembly, is there any of these directly by the screen that will pick up moisture?
As far as ATT knows, the phone LCD suddenly stopped working. I'll get a replacement and /hopefully/ theres not a moisture pad right next to the LCD assembly. Anyone know?
Click to expand...
Click to collapse
I dont know but man I hope that there isn't. Have you tried contacting invisishield? Never mind, b/c they'll blame you. Most applicators like that use alcohol to evaporate the remaining moisture that's left. My friend applied it to his, and he used very little liquid(scared), so GOOD LUCK!! I MEAN IT
Tough break, sounds dangerous to pour liquid on the screen though !
On a related matter has anyone seen pics of a Kaiser pulled apart ? Still wondering where the GPS antenna is located !
Yeah, I hope I don't get shafted.
I love the invisibleshield, and I put one on my $1,500 DSLR camera screen, but since the Kaiser screen is recessed a bit, when you squeegee the solution out from under the screen, it cannot be wiped away. It just gets pushed out between the phone's body bezel, and the screen glass -- right in to the phone. With my DSLR camera, the screen is flush with the body, so when squeegee'd I could quickly wipe the water/alcohol away.
Contacting Invisibleshield got me:
Our liability does not extend beyond our product. The lifetime warranty only covers the replacement of the invisibleSHIELD and NOT a warranty for the device the shield is protecting.
Click to expand...
Click to collapse
If ATT charges me the $400 if they find out, I guess I'll pay it. It's my fault, but by extension of invisibleshield. Guess I'll learn not to use that product on anything that has a recessed screen. I was thinking of buying an invisible shield for my laptop as well, but it's screen is slightly recessed like the kaiser, so you can forget me doing that!
xmoo said:
Damn, hate those broken screen story's. Scars the **** out of me.
Click to expand...
Click to collapse
That was why I bought the 'best screen shield on the market' for scratches (invisibleshield). Coincidentally that was the demise of my phone. I also purchased a steel case that basically would let me sit on my phone (uncomfortably) if i wanted. The desire to protect my phone, did the opposite in my case.
Wow what a horror story. Thanks for sharing with us - may prevent another phone from dying.
Wondering if you remove the battery and not using for a few days until the water dries out before turning it on?
zcink said:
Wow what a horror story. Thanks for sharing with us - may prevent another phone from dying.
Wondering if you remove the battery and not using for a few days until the water dries out before turning it on?
Click to expand...
Click to collapse
Could be, zcink. The replacement phone is on it's way. I can remove the battery during this time it takes for the replacement to come and see what happens. Unfortunately, I think one of the following has happened:
1) Water seeped between the LCD protetcive glass, and the LCD itself, and somehow soaked in to the LCD causing mini shorts -- thus resulting in kludged text.
2) Water seeped to the phone's connecting cable where the screen input is, dried on the wires, thus creating a short -- destroying the signal.
Either way, when the liquid dry's, the mineral deposits causing the short will still exist, still causing a short. For both, repair requires disassembly, voiding my warranty. I could buy a new replacement screen from the China place for about $100, but if ATT /might/ replace it without screwing me, I'll take the chance. Just wanted to know what my chances /were/ them finding out it's got water in it.
I guess the moral is.
Don't buy from InvisibleShield, unless you use a SPARING amount of spray they they include. They include a huge bottle, and I used 2 sprays worth applied to my shield. This created enough excess to be squeegeed right into my phones body. The phone worked great for a few days, until one day at work, while I was using it -- BAM -- the screen was dead.
There isn't the water dectector there, but I'm pretty sure the technicians would notice the damaged screen.
I know those screen protectors, used them for alot of things. Using one right now actully. Its the one you wash with soap and warm water, and just let it dry, it have a static adhesive to the the scree.
I see. yeah hopefully the ATT tech will be lazy and just grant you the warranty without investigating. just play dumb. If they charge you the $400 call them up and threaten to switch to T-Mobile.
My phone died and T-Mobile was going to do nothing until I threatened to switch to ATT, then they replaced it.
I seriously doubt that they will be able to tell unless you really soaked it, next time use a dry screen protector, they work just fine, no bubbles. The only moisture sensor is on the battery, and if it was a tiny amount of moisture, there's likely no signs in the screen assembly. AT&T isn't likely going to dissect the screen to check.
Kaiser disassembly howto
I have found this one somewhere here, can't remember where... Hope this helps.
http://www.mediafire.com/?0ly2msnybhb
Hadn't heard of that screen protector before, guess it would work well on an HTC Touch, not sure how the "full body" version works though!
gabriel31337 said:
I have found this one somewhere here, can't remember where... Hope this helps.
http://www.mediafire.com/?0ly2msnybhb
Click to expand...
Click to collapse
Amazing find. Thanks!
It appears to me that the screen itself is it's own modular unit. Meaning, after phone disassembly, you'd have to disassemble the actual screen itself. Further, there is no moisture indicators directly by the assembly it seems.
Knock on wood, but I'd hope a tech wouldn't go that far to determine the fault of the phone. I assume they would if theres telltale signs of water damage to the display (streaking might be a common sign.) But, maybe, just maybe, they won't.
http://www.gpspassion.com/download/HTC_Kaiser_disassembly.pdf
updating link
RemE said:
The only moisture sensor is on the battery
Click to expand...
Click to collapse
The service manual shows 4 of them, one under the battery that can be seen from the outside, one at the top and one at the bottom of the mainboard's other side, and.. one on the board that holds the bottom front panel switches, so very close to the LCD.
Personally I wouldn't have asked for a replacement phone, I'd have disassembled the phone and tried to clean it if made dirty by the liquid, bought a spare screen off ebay if it was definitely dead, and if ultimately it didn't work bought another phone off ebay for less than $400. But maybe I like risk
Here, Perfect for what you need, used it myself: http://www.mindsofwisemen.com/fileso/other/ReplacingTheLCDonaKaiser.pdf
Best wishes
Mod Edit:
Not sure if the above noted guide is officially and with permission uploaded to that site, but to give credit to members here it is (SKDVR’s Adaption of Tony Chen’s guide)
http://forum.xda-developers.com/showpost.php?p=2247685&postcount=19
i took mine apart to replace the screen; pics and info on what i did and where i got it. didn't see any water indicators near the screen when i did it, didn't think to look...
Keyboard membrane removal.
So, I've had trouble with my keyboard lately and wanted to just clean off the contacts on the membrane...but I can't seem to get the damned thing out of the plastic keyboard Middle Housing.
I have gotten everything apart so the housing is separated. Verified that I did it the way the service manual says...but i saw NOTHING about how to disassemble the keyboard from the housing.
PLZ! Pictures are good.
Try replacing digitizer screen
found that digitizer screen is above lcd and can be purcased for about $10 on ebay
hello guys,
my tytn II cant detect simcard saying the simcard is missing.
Any idea whats wrong???
help help help!
pm me and i will help.
there is a secret
ok calm down and describe problem in details not just a rough topic title and then help help help
Open back cover, let it dry for a day or two, try again, buy another
my unit is stil alive but has no lcd display
my friend (cp technician) opened it and we dry it using a hair blower but stil no display
i already tried google got no solution online can someone help me
Oh dear looks like you damaged the lcd screen from what your saying...if thats the case then time to buy a new one really. Unless you can track down a replacement lcd screen for the diamond from somewhere...get in touch with HTC and see what they say.
I hope you didn't cook it with the dryer! I have had this happen several times and a full strip and dry with a kitchen towel and a few days to dry has always seen them back to life.
you either need a new lcd screen, new flex cable to your lcd, new graphics processor, and then you will need to flash the rom
statione said:
my friend (cp technician) opened it and we dry it using a hair blower but stil no display
Click to expand...
Click to collapse
Please tell this "technician" not to use a hair dryer for drying sensitive electronics again in the future. Hot, dry air, when it hits the electronic components, will cause build-up of static electricity. Also, the hot air will probably fry up the components before all this anyways. Good luck !
So how do you recommend to dry it if I ever encounter such a problem. Just take out battery and cover and let them dry naturally on the table for some days?
DonDolowy said:
So how do you recommend to dry it if I ever encounter such a problem. Just take out battery and cover and let them dry naturally on the table for some days?
Click to expand...
Click to collapse
Yes, thats the best way, you can in some cases use dry air to blow water away
How to or not to Dry!
Look using a hair dryer will not do any harm to the components on a pc board those pcb's are mass produced they are flood soldered at about 350 to 400 degree's which is about 250 degree's hotter then a hair dryer can get. the only thing you need to worry about is getting to close to the specter strip (film cable) that can melt much lower and the lcd is 2 pieces of glass with liquid between them, heat that up and the liquid expands and crack no more display. you were correct in drying it quickly if you leave the water on the board it will begin to oxidize at the solder points and then when they (Warranty repair personal) see that ,they will tell you it is not covered. the only problem you have now is returning it for warranty exchange, there is a small litmus like dot (tab) under the battery on most phones I am not sure where it is on the Diamond but it's there. which turns color when it comes in contact with moisture that is how they know it has been exposed to water. So if they (Carrier you got the phone with) send you a replacement handset ,which is what a lot of Carriers do with phone warranty's , they send you an exchange unit, you send back the bad one and you keep the exchange. then just use a small razor blade and remove the good water dot from the replacement unit and switch it with your bad phone before you send it back to the warranty dept. As far as they are concerned you have a Diamond with a bad display.
PS. When you call to setup the warranty exchange the tech is going to ask you what color the tab I referred to is. so you need to find out from someone that has a Diamond what color the dot is ,so you can give the tech the correct answer. Hope this helps.
day 2
it seems everything is working ok but the lcd is dead and need to replace
HTC Diamond
Send us an email at [email protected]
we can get the Diamond LCD Screens.
thanks
WWW.HTCLCD.COM
WWW.HTCLCD.COM said:
Send us an email at [email protected]
we can get the Diamond LCD Screens.
thanks
WWW.HTCLCD.COM
Click to expand...
Click to collapse
your site is a scam
Scam
We have 100's of satisfied customers.
even xda-developer user like it.
http://forum.xda-developers.com/showthread.php?p=2301880
Sorry if were not perfect, sure we make mistakes but we do our best to take care of every order as fast as possible.
WWW.HTCLCD.COM
edbutler said:
Look using a hair dryer will not do any harm to the components on a pc board those pcb's are mass produced they are flood soldered at about 350 to 400 degree's which is about 250 degree's hotter then a hair dryer can get. the only thing you need to worry about is getting to close to the specter strip (film cable) that can melt much lower and the lcd is 2 pieces of glass with liquid between them, heat that up and the liquid expands and crack no more display. you were correct in drying it quickly if you leave the water on the board it will begin to oxidize at the solder points and then when they (Warranty repair personal) see that ,they will tell you it is not covered. the only problem you have now is returning it for warranty exchange, there is a small litmus like dot (tab) under the battery on most phones I am not sure where it is on the Diamond but it's there. which turns color when it comes in contact with moisture that is how they know it has been exposed to water. So if they (Carrier you got the phone with) send you a replacement handset ,which is what a lot of Carriers do with phone warranty's , they send you an exchange unit, you send back the bad one and you keep the exchange. then just use a small razor blade and remove the good water dot from the replacement unit and switch it with your bad phone before you send it back to the warranty dept. As far as they are concerned you have a Diamond with a bad display.
PS. When you call to setup the warranty exchange the tech is going to ask you what color the tab I referred to is. so you need to find out from someone that has a Diamond what color the dot is ,so you can give the tech the correct answer. Hope this helps.
Click to expand...
Click to collapse
Thanks Ed for the sensible answer based on knowledge and understanding, "Replace" is the easy answer based on ignorance. People replace lots of stuff unnecessarily IMHO, bad for the environment and your wallet too.
Also note that rubbing alcohol (methylated spirit, isopropyl alcohol) is a strong drying agent, it bonds to the water molecules and removes them by evaporation. I fixed a mobile that had been wet many months before and it cleared up the board damage shorts.
Knowledge is power, fight ignorance
Hey Guys,
Recently some salt water manage to get in my Samsung Galaxy S while i was fishing. Ive open my phone and clean as much corrosion as possible. Now I've notice that somethings are starting to fail on me in the past few hours My accelerometer, Charging port, 3.5mm head jacks, screen is all good and sim card slot. I can call out but cant take calls in. Chances are the corrosion can finish my phone off for good, in a few months time.
I was thinking if i can buy, new replacement parts or even the whole samsung galaxy s board ? and if any please link.
thank you, kindly appreciated
only level 3 services centre can get new boards but then you also need to write an IMEI to it and print out a new IEMI sticker so not something that can be done. buy a broken screen galaxy s from ebay and swap screens.
I'm sorry for your unscheduled swim.
Frankly,salt water damage is about as bad as it gets-anything depending upon capacitance or resistance will ultimately be affected by the salt.
In my opinion the whole phone is either now or soon will become erratic-even if you swap your screen into an ebay broken screen replacement as suggested I feel the screen from your current phone will deteriorate quickly so you may be sending good money after bad.
I think it's bite the bullet time
Best Wishes
Ashley
disappointed .... : \ Is the phone worth selling ? while phone housing is still new around 2 days old. Screen is still working but might die in the future due to corrosion but so far so good screen is fine.
thompson0206 said:
Is the phone worth selling ?
Click to expand...
Click to collapse
Not as a whole phone, maybe for parts, but you would have to mention the salt water damage otherwise it would be fraudulent.
Some times things happen that are just plain accidents and most likely, like AshleySear said, it's bite the bullet time time.
Maybe look around eBay for a used phone, or wait for the new Galaxy S 2.
Sorry for your potential loss,
Ian
one word....
warrenty
TheKoomba2010 said:
one word....
warrenty
Click to expand...
Click to collapse
Page 121 of the i9000 user manual.. They have a built-in water sensor, to allow Samsung to identify when moisture has entered the device. If it's similar to the iPod's, it's probably inside the headphone port (so they can see the color change without opening the device).
So don't warranty it..
There is 6 in the galaxy s plus we have microscopes to check the board as well.
Sent from my GTI-9000 Using that XDA app thingy
I hade same problem
I managed to drop my 2 weeks old GalaxySII in water. The left side of the phone was in sea water for maybe 2 seconds.
I dismounted the battery and tried to blow on it.
That war 10 days ago. Now that the warranty is gone and insurance dont cover anything I yesterday decided to disassemble it and try to clean it with filtered water.
Well the salt had dried and started to corrode on the circuits. It did not look promising but i gave it a try anyway. I used Electrical Cleaner and even bathed the circuit board in lukewarm water. The salt would not come off.
I dried then assembled the phone and pressed the power button with a spark of hope... nothing happened
So my conclusion is DO NOT BADE YOUR SMARTPHONE IN SEA WATHER!!
At least if your unlucky and it is to late put it in your pocket and annoy someone to push you into the sea. Then at least the insurance covers it
I guess my next phone will be a Motorola Defy+ or a Samsung Galaxy Xcover since i have a bad habit of breaking my phone.
today morning i droped my sgsl in detergent water .
i will keep it alone for one week
i wanted to know that detergent water damages more than water or salt water or any ways to get my phone alive
Thanks in advance for any advice offered...
Some orange juice spilled on my S6 Edge and caused liquid damage to PBA (motherboard) components. (By the way, thanks to all that called for a "cooler" looking phone...now it can't withstand a splash of liquid, but that's another post in another thread)
In my naïve nature, I assumed that Samsung would be able to repair the phone for me, albeit at a significant cost, so I sent it off to their repair center.
The ticket notes were updated after a Samsung tech looked at the phone and deemed it Beyond Economic Repair (BER) due to liquid damage to PBA components and send the broken phone in the mail without even giving me the option to pay to replace the damaged internals. After all, replacing parts of the phone should not be as expensive as purchasing the phone at full cost right?
I've done some reading online to see what options I have available to me at this point, but all seem to point to the damaged phone being a really expensive paper weight.
I just wanted to check in to see if anyone has had experience with a situation like this...or if anyone had advice on what options I have at this point.
Can the phone be repaired for less than the full retail cost of a replacement phone (approx. $900 for the model I have)?
If not, do liquid damaged phones sell for spare parts? (Screen & body of the phone are in mint condition)
You can go to Swappa.com and look in the boneyard to see if anyone is selling a busted s6 for parts. You can also sell your damaged phone in the boneyard.
It was likely more than a splash, I'm guessing a spill or full dunk if it migrated all the way through to the motherboard?
I've dropped my phone in a full sink of water (twice) and immediately grabbed it out and it was completely unharmed.
If a splash had the ability to damage it, then how did it manage to do this:
https://www.youtube.com/watch?v=LGBKmIlk52Q
Is there any life in the phone at all? Orange juice is very corrosive and a electrical conductor due to the ions in the juice, so it doesn't take much to short things out and reek havoc. I don't know how good you are at taking things apart and fixing them but if it were me I would tear into it and completely disassemble it. Wash all the boards thoroughly with distilled water then give it a soaking in 100% isopropal alcohol. Let it dry thoroughly, check the battery for voltage and try and fire it up. Don't wash or soak the battery by the way. I've fixed a few phone this way that had coke or dirty water in them. Had an iPhone my wife dropped in a toilet last an additional two years after doing this. I had a phone myself I dropped in a glass of diet coke go back to working after a thorough cleaning. Still works to this day and that's been years ago. Those technicians aren't going to spend the time doing this due to the cost of the labor and the off chance it may quite on you down the rd. Anyhow, hope you can revive it. Good luck!
RajCaj said:
Thanks in advance for any advice offered...
Some orange juice spilled on my S6 Edge and caused liquid damage to PBA (motherboard) components. (By the way, thanks to all that called for a "cooler" looking phone...now it can't withstand a splash of liquid, but that's another post in another thread)
In my naïve nature, I assumed that Samsung would be able to repair the phone for me, albeit at a significant cost, so I sent it off to their repair center.
The ticket notes were updated after a Samsung tech looked at the phone and deemed it Beyond Economic Repair (BER) due to liquid damage to PBA components and send the broken phone in the mail without even giving me the option to pay to replace the damaged internals. After all, replacing parts of the phone should not be as expensive as purchasing the phone at full cost right?
I've done some reading online to see what options I have available to me at this point, but all seem to point to the damaged phone being a really expensive paper weight.
I just wanted to check in to see if anyone has had experience with a situation like this...or if anyone had advice on what options I have at this point.
Can the phone be repaired for less than the full retail cost of a replacement phone (approx. $900 for the model I have)?
If not, do liquid damaged phones sell for spare parts? (Screen & body of the phone are in mint condition)
Click to expand...
Click to collapse
You picked the phone! you could have gotten the less flashy seemingly more durable sibling if you had wanted.
Otherwise though yeah, you could see how much Samsung would charge you to fix it, and or start looking for replacement parts.
TechSavvy2 said:
It was likely more than a splash, I'm guessing a spill or full dunk if it migrated all the way through to the motherboard?
I've dropped my phone in a full sink of water (twice) and immediately grabbed it out and it was completely unharmed.
If a splash had the ability to damage it, then how did it manage to do this:
https://www.youtube.com/watch?v=LGBKmIlk52Q
Click to expand...
Click to collapse
It was in a bag with a unsealed bottle of orange juice. When the bag was picked up, the bottle of orange juice spilled and wet the phone. It wasn't fully submerged, and was in contact with the juice for 30 seconds max.
The phone was a little wet on the outside, but was still functional. I wiped it off and the phone operated with no problem.
Few hours later it started acting up. I restarted it and could never get it to boot back up, while not plugged in, since.
As a matter of fact, I didn't shut the phone down and immediately start remediation because I assumed (from watching the videos like you linked) the phone was capable of withstanding brief exposure to liquid.
beaverslayer said:
Is there any life in the phone at all? Orange juice is very corrosive and a electrical conductor due to the ions in the juice, so it doesn't take much to short things out and reek havoc. I don't know how good you are at taking things apart and fixing them but if it were me I would tear into it and completely disassemble it. Wash all the boards thoroughly with distilled water then give it a soaking in 100% isopropal alcohol. Let it dry thoroughly, check the battery for voltage and try and fire it up. Don't wash or soak the battery by the way. I've fixed a few phone this way that had coke or dirty water in them. Had an iPhone my wife dropped in a toilet last an additional two years after doing this. I had a phone myself I dropped in a glass of diet coke go back to working after a thorough cleaning. Still works to this day and that's been years ago. Those technicians aren't going to spend the time doing this due to the cost of the labor and the off chance it may quite on you down the rd. Anyhow, hope you can revive it. Good luck!
Click to expand...
Click to collapse
It has *some* life. If I plug the phone in to a generic USB power brick, the Samsung logo will pop up & start the AT&T music and then immediately goes into a reboot loop where it starts the process over again. If I plug it into the Samsung USB brick it came with, I was able to get it to fully boot into the operating system, but crashed the first time I tried to access my pictures in the gallery, and then allowed me to pull up the pictures after a second try.
If there is no power going to the phone (via USB or wireless charging) the phone does not respond at all.
I watched a video of a S6 Edge teardown and it's MUCH more difficult than the previous models (which had removable back panels). I think iFixit rated it a reparability score of 3 out of 10.
They had to use special equipment to lift the back glass up enough (just short of breaking it) to get a guitar looking pick underneath to remove the glue. Once the back glass is off, they had to also unglue the battery to get it out.
Not having much to loose at this point, I submerged it in 91% iso-rubbing alchohol for 3hrs and will let it set in a bag of rice for 2-3 days.
I think the damage has already been done though. Will removing corrosion after there's been a short on the circuit board do anything?
whoamanwtf said:
You picked the phone! you could have gotten the less flashy seemingly more durable sibling if you had wanted.
Otherwise though yeah, you could see how much Samsung would charge you to fix it, and or start looking for replacement parts.
Click to expand...
Click to collapse
Yea, I did pick it. IR blaster is an important feature for me, so my options were HTC or Samsung. I've owned 2 galaxy phones & like the synergy with my Samsung TV so I went for the Galaxy....despite my concerns with the step backwards (in terms of water resistance & utility) from the S5.
I've talked to Samsung and they will not give me an option to repair. They say that the parts + labor to fix the phone exceeds the cost of a new phone.
When a phone with possible water damage is sent to Samsung for repair....do they actually open up the phone to verify it's liquid damage, or do they just look for the liquid indicator and call it liquid damage if it's red?
My regular S6 survived a massive downpour yesterday while hiking I have no idea how I got so lucky. I opened it up to check it too and everything was okay internally. I guess they weren't kidding when they said it can withstand some liquid damage so long as it isn't submerged.
From the Moderator
To all in this thread ........... Water damage, liquid damage .....etc
To answer a couple of these questions .......... If water infiltrates inside the back of the phone ...... there is a strip that will change properties that indicates water got in the phone. Newer devices (not just phones, cameras lenses...etc) uses more exotic materials that you cannot easily detect ..... they will show up under UV .......... so to answer that Yes the manufacturer usually can tell..... if it is not obvious, often they do not check ......
To all the Physics ..... comments .......... Water infiltrates based on the seal of the back or the front depending on how the phone is constructed air resistance within the device if sealed ...we could assume it is 14.7 psi or Sea level average atmospheric pressure. As soon as you drop something into say a pool, if it were to sink to 5-feet under the psi would increase to about 17 psi outside force pushing against the interior 14.7 psi....... Without getting into partial pressure laws and more math and physics.........
Greater Out side force is exerting against a lesser force inside the phone........ this precipitates faster infiltration ......... All aforesaid is great academics ......... The Bottom line is this
If you drop your phone into water or any water based fluid then...... Remove as quickly as possible, remove the power source (this is why I prefer a removable battery) the power source is the thing that Really speeds up the water damage.
So here is how to deal with water intrusions
1. Dry it off
2. Remove the power source asap
3. Dry it again .....
4. Immerse is Rubbing alcohol 91% (preferably Denatured reagent) if possible, the Alcohol bonds the water molecules to it for a minute or 2........ then remove and dry off with paper towels
5. Then put in Millet, Rice, Desiccant... etc
I have had to do this a number of times in my life with underwater cameras when the housing leaks ........ a real pain being 100-120 feet under and have to stop the shoot because of a housing leaks
But considering my average lens is 1000 bucks and saltwater will destroy the coatings (not to mention electronics) I have only lost 1 lens and one camera in 25 years and no phone ever due to water infiltration occurrences. But being careful and immediate response is the key ....... be Vigilant ( in this case, that means know how to open the phone and remove the power source)
Hope that helps clear some things up ..........
In South Africa we get ADH (accident and damage handling) on Samsung flagships, but they have been tightening the strings since the S5.
ADH covers screen / body damage with a free repair as part of the warranty.
Water damage on the S6 AFAIK isn't covered anymore like it was on previous Galaxy devices.
Sent from my SM-G920F using Tapatalk
RajCaj said:
Thanks in advance for any advice offered...
Some orange juice spilled on my S6 Edge and caused liquid damage to PBA (motherboard) components. (By the way, thanks to all that called for a "cooler" looking phone...now it can't withstand a splash of liquid, but that's another post in another thread)
In my naïve nature, I assumed that Samsung would be able to repair the phone for me, albeit at a significant cost, so I sent it off to their repair center.
The ticket notes were updated after a Samsung tech looked at the phone and deemed it Beyond Economic Repair (BER) due to liquid damage to PBA components and send the broken phone in the mail without even giving me the option to pay to replace the damaged internals. After all, replacing parts of the phone should not be as expensive as purchasing the phone at full cost right?
I've done some reading online to see what options I have available to me at this point, but all seem to point to the damaged phone being a really expensive paper weight.
I just wanted to check in to see if anyone has had experience with a situation like this...or if anyone had advice on what options I have at this point.
Can the phone be repaired for less than the full retail cost of a replacement phone (approx. $900 for the model I have)?
If not, do liquid damaged phones sell for spare parts? (Screen & body of the phone are in mint condition)
Click to expand...
Click to collapse
Purchase an s6 active
Sent from my SAMSUNG-SM-G890A using Tapatalk
Beyond Economic repair means the cost of fixing it is more than the phones cost.
Yes, the phone that just released in the US last Friday, on AT&T only.
Had I known what I know now about the S6 Edge's ability to stand up to liquid exposure & the cost to repair liquid damaged phones, I would have foregone the Edge pre-order and waited the 2 months for Samsung to offer a waterproof version of the phone. Also, prior Active models had lesser hardware profiles and wouldn't have seemed like a good alternative for me when I was in the market for a new phone.
I really wish more manufactures built their phone with IR ports....then I wouldn't be beholden to Samsung's BS.
oka1 said:
So here is how to deal with water intrusions
1. Dry it off
2. Remove the power source asap
3. Dry it again .....
4. Immerse is Rubbing alcohol 91% (preferably Denatured reagent) if possible, the Alcohol bonds the water molecules to it for a minute or 2........ then remove and dry off with paper towels
5. Then put in Millet, Rice, Desiccant... etc
I have had to do this a number of times in my life with underwater cameras when the housing leaks ........ a real pain being 100-120 feet under and have to stop the shoot because of a housing leaks
But considering my average lens is 1000 bucks and saltwater will destroy the coatings (not to mention electronics) I have only lost 1 lens and one camera in 25 years and no phone ever due to water infiltration occurrences. But being careful and immediate response is the key ....... be Vigilant ( in this case, that means know how to open the phone and remove the power source)
Hope that helps clear some things up .........
Click to expand...
Click to collapse
Thanks for the advise....I will certainly handle things differently if this ever happens again.
Couple of quick questions, since you have experience with this stuff....
Is it possible for the 91% alcohol to further damage the device? Are there specific components that do okay in an alcohol bath vs others? IE battery, speakers, camera, etc?
Also, how long should you dry the phone in absorbent material before attempting to power it up again?
Before I sent the phone off to Samsung, I could at least get the phone to power up while plugged in.
Since I've received the phone back from Samsung, and have given it the alcohol / rice treatment, the phone won't power up at all...even plugged in.
Either way, the phone is dead I'm afraid. Since I'm not certain which components are working, and are not, I can't even sell the thing for spare parts. Most expensive paperweight I've ever owned!
RajCaj said:
Thanks for the advise....I will certainly handle things differently if this ever happens again.
Couple of quick questions, since you have experience with this stuff....
Is it possible for the 91% alcohol to further damage the device? Are there specific components that do okay in an alcohol bath vs others? IE battery, speakers, camera, etc?
Also, how long should you dry the phone in absorbent material before attempting to power it up again?
Before I sent the phone off to Samsung, I could at least get the phone to power up while plugged in.
Since I've received the phone back from Samsung, and have given it the alcohol / rice treatment, the phone won't power up at all...even plugged in.
Either way, the phone is dead I'm afraid. Since I'm not certain which components are working, and are not, I can't even sell the thing for spare parts. Most expensive paperweight I've ever owned!
Click to expand...
Click to collapse
Cannot put in Alcohol if the battery is connected ....... Battery and any fluid = not good .... The other items really will not do anything ........ either way Go to Pandawill.com, Aliexpress.com, Dynamism.com or Chinawholesale.com one of those websites sells motherboards and other cell phone parts I think I saw them for like 80 bucks ......... worth looking into ..... Sorry the phone died...... good luck
You can buy it from aliexpress,amazon or HCQS
Just wanted to share my negative experience and may be get a piece of advise. I dropped my Galaxy S6 (not edge) into the water after which home button stopped working. Couple weeks later as home button were still not functioning I soaked my phone in 99.9% of isopropyl alcohol. Couple hours later half of screen stopped reacting to fingers, and a few hours screen become black. There were also significant damage to frond and back panel plastic base behind the glass - see photos. I still hear some notifications which gives me a hope that there are still some life in it. I also left phone in rise for 4 days with no improvement. Does anyone had such a negative experience with Alcohol soaking and what could be a solution if any?
zipper3 said:
Just wanted to share my negative experience and may be get a piece of advise. I dropped my Galaxy S6 (not edge) into the water after which home button stopped working. Couple weeks later as home button were still not functioning I soaked my phone in 99.9% of isopropyl alcohol. Couple hours later half of screen stopped reacting to fingers, and a few hours screen become black. There were also significant damage to frond and back panel plastic base behind the glass - see photos. I still hear some notifications which gives me a hope that there are still some life in it. I also left phone in rise for 4 days with no improvement. Does anyone had such a negative experience with Alcohol soaking and what could be a solution if any?
Click to expand...
Click to collapse
If your phone is still acting like that or even died, you can open it up ( check youtube vids for dissasembly )
Take any clean alcohol..95%+ and ESD brush ( or toothbrush if you dont have any ) Take off any modules from your motherboard like microphones, cameras, usb board etc. Then gently clean everything with brush and alkohol. When you're finished - put it in electric oven if u have any for 1-2 hours in max 90 degrees temp. If not - use a hairdryer. Do same thing with usb board. Then put it back togheter and try.
So... teardown videos on YouTube fooled me and I thought that this phone is water-resistant. I washed it under tap water (multiple times, actually). After the last time, the screen stopped working, but the phone appears to be OK — even the touch clearly works. I've already disassembled the phone and cleaned the connectors with 95% alcohol, but the screen still doesn't work. Is buying a replacement screen and hoping for a cheap repair the smartest thing to do? After all, the motherboard can also be borked.
EDIT: the screen is completely black
BlueOner said:
So... teardown videos on YouTube fooled me and I thought that this phone is water-resistant. I washed it under tap water (multiple times, actually). After the last time, the screen stopped working, but the phone appears to be OK — even the touch clearly works. I've already disassembled the phone and cleaned the connectors with 95% alcohol, but the screen still doesn't work. Is buying a replacement screen and hoping for a cheap repair the smartest thing to do? After all, the motherboard can also be borked.
EDIT: the screen is completely black
Click to expand...
Click to collapse
I've replaced the screen after dropping the phone. Was only a small chip in the bottom corner, didn't look much at all, but the screen was completely dead. I was in a similar dilemma of wanting to be sure it was only the screen before spending about $100 on a screen. I booted into fastboot, then connected to a PC, then done the fastboot devices command, which returned a valid ID, so I knew the phone wasn't completely dead. Also connecting to the PC and booting the phone, the PC recognised the phone was connected, though without being able to unlock the phone I couldn't check anything else. That was enough for me to go ahead and order the screen. Now everything works fine.
Robbo.5000 said:
I've replaced the screen after dropping the phone. Was only a small chip in the bottom corner, didn't look much at all, but the screen was completely dead. I was in a similar dilemma of wanting to be sure it was only the screen before spending about $100 on a screen. I booted into fastboot, then connected to a PC, then done the fastboot devices command, which returned a valid ID, so I knew the phone wasn't completely dead. Also connecting to the PC and booting the phone, the PC recognised the phone was connected, though without being able to unlock the phone I couldn't check anything else. That was enough for me to go ahead and order the screen. Now everything works fine.
Click to expand...
Click to collapse
Thanks for sharing your experience! In my case, the phone clearly isn't dead, but I wonder whether some circuitry on the motherboard that's responsible for making the display work might be fried. Well... if that's the case, I can always sell the replacement screen after testing, but I'm not sure that someone will buy it for a good price.
Also... where did you get your screen from? On AliExpress, they are as cheap as $50, but most of the cheap ones are clearly some fake crap — TFT/IPS LCD, smaller than the original, fingerprint scanner not working... I guess I need to buy something more expensive. Have you noticed any difference between the original screen and your replacement?
BlueOner said:
Thanks for sharing your experience! In my case, the phone clearly isn't dead, but I wonder whether some circuitry on the motherboard that's responsible for making the display work might be fried. Well... if that's the case, I can always sell the replacement screen after testing, but I'm not sure that someone will buy it for a good price.
Also... where did you get your screen from? On AliExpress, they are as cheap as $50, but most of the cheap ones are clearly some fake crap — TFT/IPS LCD, smaller than the original, fingerprint scanner not working... I guess I need to buy something more expensive. Have you noticed any difference between the original screen and your replacement?
Click to expand...
Click to collapse
It was 4 months ago I got mine from AliExpress, at that time there wasn't any of these cheaper ones for sale. Looking at these cheaper ones they are TFT, though it's not always obvious in the description.
One seller is selling both TFT and OLED and are clearly labelled in the options. So from this assume that all cheaper ones are TFT.
It is a bit of a minefield. I doubt that any of the sellers have the actual original genuine screens. It took me a couple of days to go through all the listings and determine which one would most likely be good quality.
I eventually went for this one, which was slightly more expensive than most. Now though it appears to have gone up about $15 from when I bought it.
https://a.aliexpress.com/_d7OqLlE
At that time it had the best reviews, which appeared genuine. There were others with a higher review count, which appeared to be just as well reviewed, but reading the reviews you realise they are fake. Many reviews, supposedly from the USA, written in very poor pigeon English.
Also saw some stores with high review count, but then realised that most reviews are for completely different products (a common trick by some Ali sellers, completely change an existing listing so a new product looks like it's got high reviews)
The screen is good quality. It took about 3 weeks to arrive, but it was about 2 weeks after I damaged it before I ordered. So it was around 5 weeks after I last used the phone before installing it. After that time it's hard to judge if it is as good as the original. To look at and use the phone you wouldn't think it was a non original replacement, to me it seems to be as good as the original, without doing a side by side comparison. As far as an oleophobic coating, I couldn't say, it's had a screen protector since installing.
BlueOner said:
I washed it under tap water (multiple times, actually)
Click to expand...
Click to collapse
Umm. What? Even with IP rated phones you don't wash it with water. IP rating generally means that its good for accidental drops into water or for use in light rain. Why on earth would you wash it? Yes, I know jerryrig says there's some water ingress protection but it doesn't mean you should wash it with water. It just means you're good for use in light rain at best.
lambstone said:
Umm. What? Even with IP rated phones you don't wash it with water. IP rating generally means that its good for accidental drops into water or for use in light rain. Why on earth would you wash it? Yes, I know jerryrig says there's some water ingress protection but it doesn't mean you should wash it with water. It just means you're good for use in light rain at best.
Click to expand...
Click to collapse
Yes, I know. Very stupid. At least y'all can learn from it and avoid making the same mistake.
Robbo.5000 said:
The screen is good quality.
Click to expand...
Click to collapse
That's reassuring!
Robbo.5000 said:
it's hard to judge if it is as good as the original. To look at and use the phone you wouldn't think it was a non original replacement, to me it seems to be as good as the original, without doing a side by side comparison.
Click to expand...
Click to collapse
Well, I guess that even if it's a bit worse, replacing the screen is better (in my case) than dealing with an older/cheaper phone or throwing a nice sum of money on a phone in similar price range. I will report my experience after replacing the screen, maybe it will help someone. I'm definitely not going to find another guy with 9T (Pro) because of the coronavirus, but comparison with another high-quality AMOLED phone is another way to check the quality.
So... I wanted to order the screen, but when I checked whether the phone still works... it appeared dead. It charges, is visible in USB devices (but no fastboot etc.), the notification LED blinks, but that's all. It worked perfectly some time after the water damage occured, so I guess that the damage progressed. Yes, I didn't clean the phone thoroughly after disassembling it - I thought that the water probably evaporated anyway after using a heat gun, so, as I mentioned earlier, I cleaned only (easily accessible) connectors. Maybe it is something stupid (power button?), but it seems too good to be true. If I don't post another update, just assume that my phone died.
BlueOner said:
So... I wanted to order the screen, but when I checked whether the phone still works... it appeared dead. It charges, is visible in USB devices (but no fastboot etc.), the notification LED blinks, but that's all. It worked perfectly some time after the water damage occured, so I guess that the damage progressed. Yes, I didn't clean the phone thoroughly after disassembling it - I thought that the water probably evaporated anyway after using a heat gun, so, as I mentioned earlier, I cleaned only (easily accessible) connectors. Maybe it is something stupid (power button?), but it seems too good to be true. If I don't post another update, just assume that my phone died.
Click to expand...
Click to collapse
Press F in the comments section guys
My k20 pro Disable screen problem
Hi xda developers
After wetting the phone with a hand sanitizer and using the same wetness of the screen, I played the online game and put it in automatic game mode and rested for a while...
After waking up, I noticed that the phone was turned off, which was turned on by holding down the power button, but the screen is off...
Currently, only vibrators and notification lights work for the phone, and the phone is organized by a computer.
Also, the phone is charged and its sound can be heard while connecting it to the charger, and its sound can be heard in the same way to lock the screen.
Does anyone have an idea?
my phone just take s swim in the river yesterday, now its has no display but still on and even the touchscreen is working (i know is working cuz its register sound when i try to touch it everywhere). it have been dead first but then turn back on with everything work normal. but after about half hour, the screen suddnly dead.
after tear it my self i found where the water coming in, its from the 3.5mm jack. other holes have rubber protection but the jack has nothing. they even put water dammage indicator below the 3.5mm module....
i have try few method like clean the board with isoprofil alcohol but no avail. now im waiting my screeen replacement and will try to fixit my self.
IchsanWin32 said:
my phone just take s swim in the river yesterday, now its has no display but still on and even the touchscreen is working (i know is working cuz its register sound when i try to touch it everywhere). it have been dead first but then turn back on with everything work normal. but after about half hour, the screen suddnly dead.
after tear it my self i found where the water coming in, its from the 3.5mm jack. other holes have rubber protection but the jack has nothing. they even put water dammage indicator below the 3.5mm module....
i have try few method like clean the board with isoprofil alcohol but no avail. now im waiting my screeen replacement and will try to fixit my self.
Click to expand...
Click to collapse
Hello! Had exactly the same issue. Did it work to replace the screen?
My phone got into the sea (well the sea went into it), nothing happened for a while, and then it suddenly went black. Is working (like i can still use it as alarm lol) but the screen is not. Same as BlueOner, i'm afraid is not the screen itself but something in the mother board, so I would love to know if any of you were able to use it after replacing the screen or i will end up with the same issue.
Thanks!
saityro said:
Hello! Had exactly the same issue. Did it work to replace the screen?
My phone got into the sea (well the sea went into it), nothing happened for a while, and then it suddenly went black. Is working (like i can still use it as alarm lol) but the screen is not. Same as BlueOner, i'm afraid is not the screen itself but something in the mother board, so I would love to know if any of you were able to use it after replacing the screen or i will end up with the same issue.
Thanks!
Click to expand...
Click to collapse
It's toast. Don't even bother. The sea salt is hygroscopic, conductive (with moisture), corrosive and -everywhere- now.
It not a question of if it will fail only when.
Tap water is similar but not near as aggressive. The smallest amount of salt (sweat) can change that if it gets inside too. Even so if the device >didn't have it's battery pulled immediately<, then completely turn apart and cleaned with anhydrous isopropyl alcohol it won't fare much better in the long term most likely.
Any water internally can cause massive damage quickly. Or the signs of damage can take months to fully manifest themselves especially if the battery wasn't quickly pulled.
Salt water is fatal because it's residue doesn't easily rinse off as well as what was stated above.
This is why manufacturer warranties refuse to deal with water damage.
It's the gift that keeps giving...
Occasionally you can get lucky if you act fast
My Buds case fell into my coffee cup and immediately crash dived to the bottom like the sub in Das Boot. Cream and sugar too.
I pulled it apart and rinsed it will RO water then with anhydrous isopropyl alcohol in less then 3 minutes. Got as much as the isopropyl out as possible without compressed air and allowed it to dry in a warm sunny spot. Couldn't disconnect the Li battery as it was soldered or spot welded in. After about 2 days of drying it worked and other a year and a half later still is working.
I am still surprised...
Hi. I got water damage. The screen can be turn on but its not responding at all. I can press the power button, the screen lights up, as normal. I just couldn't unlocked it. It wont accept any touch. Also i tried calling from another phone, sound okay, also led notification working.
I havent try the charging port yet.
Anybody have similar experience? Can someone explain my problem? Should i order new screen replacement? Im just afraid its not screen problem.
harithzaim88 said:
Hi. I got water damage. The screen can be turn on but its not responding at all. I can press the power button, the screen lights up, as normal. I just couldn't unlocked it. It wont accept any touch. Also i tried calling from another phone, sound okay, also led notification working.
I havent try the charging port yet.
Anybody have similar experience? Can someone explain my problem? Should i order new screen replacement? Im just afraid its not screen problem.
Click to expand...
Click to collapse
Read my previous post.
You need to dry it out completely.