I want to upgrade my diamond to the 1.93,but I can't.
I have tried using the signed Hard-spl and Unsigned Hard Spl each time it finishes in a minute and says that it has successfully completed but when the phone restarts,it is on the same rom. I have even tried the official rom upgrade from HTC E-club,that just gives me an error and guides me how ot get it back, please help
I know that its is pretty strange,I have searched but I have not seen a similar problem
Bump,sorry I really want to upgrade
Sounds like you've flashed the Hard-spl but not a ROM
After you flash unsigned Hard-spl, you need to flash any of the ROMs you like from the Rom Development forum after that. The Hard-spl merely opens your phone up so it can be flashed with another ROM but does not contain a ROM with and in itself.
i know that I am not stupid
the hardspl didn't work becuase I have entered the bootloader mode and it didn't say Olinex 40 ,or something like that,and like i said I tried flashing the offical rom from htc e club and that didn't work
bump bump bump
Related
I know there are others experiencing the 28% death wall while trying to flash WM6, but there doent seem to be any specific solutions to this.
I have a Dopod D810 and has already installed 1.30 olipro. Just trying to flash to the official WM6 ANZ Rom. No luck.
Any suggestions guys?
Should just be a very straight forward procedure. Flashing a Dopod with an official Rom.
should be, but it's not... mine is Dopod asia, and stuck at 28% when flashing. Not too sure, but really seemed to me that it was something related to hard-spl. After the 28% error, i reflashed an unofficial rom and tried the official again.
eventually it worked for me.
i guess you don't technically need to manually enter hard-spl first before flashing official ROM.. if anything went wrong i guess you could send it back to them..
safest is to use a modified RUU so it just flashes ROM without IPL + SPL.. i thiiiiiink problem is something to do with SPL
which unofficial rom did u reflash it to? I've been going back and forth with AX3L_OS v3.0.0.2 and the official ANZ dopod rom.
tried about 5 times now. still trying. each time it fails at 28% it's another 10 minutes to flash backto the unofficial rom.
maybe if i try to trce ur steps exactly it might work.
i was flashing to some pdaviet ROM, but i don't think that would make any difference from ax3l's...
have you tried flashing the official ROM with a modified RUU, or you really want the whole package...
If you're just trying to keep everything official i guess you could try to flash the official rom without manually entering bootloader and take your chances. Being that its an official ROM i guess it's safer, or at least covered in warranty..
One question, why don't you try to flash to official WM5 ROM, then to official WM6.. since technically it's supposed to work that way
seriously, i'm not sure why you'd want the official one though.. it's nothing special
Yeah I've tried flashing back to the official WM5 and then WM6, same story.
Tho I havent tried flashing the official WM6 through modified RUU, mainly coz i dont know how to.
Also, In the AX3L version of WM6, there doesnt seem to be a phonepad input method. only keyboard and block recongniser and one other one. Is that coz it's a modified rom, or does WM6 not have the phone pad input. if that's the case i can forget about flashing to WM6 all together.
can't remember if official wm6 has phonepad, but you can just install a cab for it, so it's not a big deal.
look on my site for a link to modified RUU official ROM... instructions are here
i had a lot of problems being stuck at 28%
what eventually i got it to flash to the aus rom was i used SPL 1.20 then it seemed to flash fine.
for some reason my phone doesnt like any other version of SPL besides the one on the latest aus rom either, i flashed to a cooked rom and couldnt flash back until i had put spl 1.20 back in then flashed back to the aus rom.
I have the same problem with 28% stucking
I try to reflash but I still have the same
do you have hard-spl? if so, which version? If you do, flash back a cooked ROM..
if not, you need to try to flash official ROM..
if neither is working, use splxploit. I think all links you need are in this thread already
I have a same problem.
I was upgraded from WM5 to Hong Kong Official WM6 chinese ROM, then I want to change to Official English ROM, I did the Hard-SPL 1.3 and get the SuperCID, but when upgrading the WM6 English officeial ROM, this was stuck at 28%.
Now I was able to flash back to WM5 rom, but I world like to Upgrade to WM6 official ROM, anyone help?
I had this problem when upgrading to the Australian WM6 official HTC Release. The way around it is to run the Trinity Service Provider & CID unlock program from the link below. Dont know why but to use either release, Dopod or HTC WM6 you must run this tool first.
ftp://xda:[email protected]/Trinity/Tools_and_Programs/HTC_Trinity_SIM_CID_Unlock_v1.zip
Hope this helps
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
HI, Thank for your reply, how can I do the modified RUU?
Hi all,
I have success to flash the WM6 official ROM.
this is my experience:
To flash the Radio ROM first, I has flash the 1.50.08.11 Radio ROM.
Then to download the Dutty NBH Tool to take off the Radio DOM of WM6 official ROM.
Then to flash the modify ROM.
Now, my phone is running WM6.
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
Learn something new everyday. Never knew that simply modifying the RUU would itself allow the updates. Just tried it, and yes it works also.
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
how do mofify the RUU? and what do I modify it to?
thanx walterjm
Can you share HK-CHT rom for noSPL noIPL noRadio ? Thanks!
WildsideUK said:
I had this problem when upgrading to the Australian WM6 official HTC Release. The way around it is to run the Trinity Service Provider & CID unlock program from the link below. Dont know why but to use either release, Dopod or HTC WM6 you must run this tool first.
ftp://xda:[email protected]/Trinity/Tools_and_Programs/HTC_Trinity_SIM_CID_Unlock_v1.zip
Hope this helps
Click to expand...
Click to collapse
Can you share HK-CHT rom for noSPL noIPL noRadio ? Thanks!
I had the same problem and I resolve it by extract the rom and re-build it ... look at the thread http://forum.xda-developers.com/showthread.php?t=327667
Good luck
At the point I am I need the help of experienced Users from the community.
I flashed a original HTC Wings (S730) with WM 6.1 ROM. It runs perfectly until I got a hardware problem (radio) . This is the reason I have to send it back to the official service.
Therefore I tried to go back to an official ROM from the http://wiki.xda-developers.com/index.php?pagename=WINGS_WM61_Alcaline
At first I flashed the earlier backuped Bootloder via sspl-0.91-wings.exe. This seems to be okay. But as I tried to flash an official ROM from the site mentioned above, during the flashing process I've got the note 'ERROR 294 Invalid vendor ID'. What was wrong? Did I forget any step?
Please, is there anyone who can describe the correct way back to 'warranty' for a newbie?
Thanx a lot.
have you tried all the ROM's? there is one prerelease and two release ROM's.. try both of the release roms, they might be for different production models/locations.
I tried both official released ROM's (signed as 'Ship'), not the prerelease version.
and if you first flash the shiped rom (with hardspl) and when done flash the back-up of the spl
With reference to an earlier statement of bigflavour in the thread http://forum.xda-developers.com/showthread.php?t=383617&page=17
I flashed back the original SPL at first.
Too bad It seems to be that I have a new problem now. Few minutes ago I have tried to reinstall hardSPL on the device via the well known sspl-0.91-wings.exe running on the Wings. But as I started the sspl, the device shows on the display that 'Access denied....is not digitally signed with a trusted certificate'.
Thereupon I thought I had to 'application_unlock' the device. After running the SDA_App...Unlock on my PC the display message shows succesful unlocking process. B U T, the sspl doesn't run as before.
Now, I'm totally confused. What has happened??
It's flavor, and unfortunately, I have no idea how to help you.
Probably tried the European english's spelling hehe.
Also This does seem like an odd problem, have you tried for kicks doing the factory reset to see if it will reset some of the registry and maybe fix your issues? I dont know anything about the spl's since I have no need to upgrade to 6.1, I wouldnt imagine it causing any more damage but again I dont know what all was done. I havnt followed those threads for a long time.
Thanx a lot. Apparently, the hint to make a hard reset hits the mark. Now I flashed back the HardSPL. So I'm back at the starting line . Does anyone knows if the official ROM from the http://wiki.xda-developers.com/index..._WM61_Alcaline is the latest one and can I use it for the warranty return?
Or should I look for an original German HTC ROM?
I was a little bit to fast. I will need a German ROM definitely, because the ROM from the Wiki doesn't include a the german language option.
Is there anyone who can help me with a original HTC S730 ROM for the german market?
Thank you in advance.
Hallo HSN,
if you give me a introduction how I backup my ROM, you can have my one. I own a German HTC S730. But I am confused when I read all threads about flashing etc....
One page introduction how to back up and you can have my one.
But I think that the Repair center here in Germany, doesn't care about the Rom you have installed.
Hi,
Just downloaded the new R3 UK firmware for my X1
I tried to Hard Spl my phone but it failed at 0%
But..
I thought id try flashing the firmware WITHOUT a hardspl using the microsd method.. and it worked :S is this normal?
everything seems to be working fine...
will anything happen to my phone in the future?
If it helps i was using 02 R2 firmware previously
Thanks
Adam
If I read your post correctly. You went and flashed an official SE Rom which you wouldn't need HardSPL for because they are released by SE and aren't custom roms.
You could of got the same by using the auto update service. You will only need HardSPL, is you try and flash any of the custom roms in this forum.
Well ive debranded by phone then...
and according to the turtorial flashing roms
http://forum.xda-developers.com/showthread.php?t=446070
you have to use HardSpl
I just wondered that if i didnt have a hardspl would this cause any problems with my phone.
That update would not have been available through SEUS because i have an o2 branded x1.
So am guessing there isnt going to be any problems with my phone? and if it ever breaks will it need to be flashed back to 02 R2?
Thanks
adamleerusse said:
Well ive debranded by phone then...
and according to the turtorial flashing roms
http://forum.xda-developers.com/showthread.php?t=446070
you have to use HardSpl
I just wondered that if i didnt have a hardspl would this cause any problems with my phone.
That update would not have been available through SEUS because i have an o2 branded x1.
So am guessing there isnt going to be any problems with my phone? and if it ever breaks will it need to be flashed back to 02 R2?
Thanks
Click to expand...
Click to collapse
Can somebody please send a message to the mods or topic creator or something to change the title to "how to flash CUSTOM ROMs?" This would make it much easier to understand, and less of a hassle for newcomers to flash OFFICIAL Roms.
I've been lurking with the XDA forum for quite sometime now and its my very first posting and I'm having difficulties finding answers on search box I just simply give up looking for appropriate answer to my question. Since I like to use the good old Winmo 6.1 rom (Davideuck_V-7_MSVC to be exact)my bad is I forgot to SPL to earlier version 1.15 so got a green kinda thing on my screen, so I apply Restore_Stock_SPL_115 and everything went fine. (I know I'm stupid ) Unfortunately after I update the Time and Date it suddenly appear " This concludes the beta test for this software release....... blah, blah,.... guess what? its a time bomb can't do anything on screen but to reset. So I decide to re-flash it again but I got stuck at 0% on bootloader mode and got Error 262, I tried to understand whats the meaning of it and I did, but never got any solution how? I tried to flash it with HSPLWrapper_Blackstone_156OliNex to restore Winmo 6.5 but I got stuck again on 0%. something unusual I tried to reflash more roms and it didn't work. All the Roms I've wont reach 1% Even flashing on SD card trick wont load. And my spl ver 1.15 can't flash anything. So I that's why I need your help desperately...
Near enough the exact same situation as me! I think that 1.15 file may have issues.
wayneroughneckz said:
I've been lurking with the XDA forum for quite sometime now and its my very first posting and I'm having difficulties finding answers on search box I just simply give up looking for appropriate answer to my question. Since I like to use the good old Winmo 6.1 rom (Davideuck_V-7_MSVC to be exact)my bad is I forgot to SPL to earlier version 1.15 so got a green kinda thing on my screen, so I apply Restore_Stock_SPL_115 and everything went fine. (I know I'm stupid ) Unfortunately after I update the Time and Date it suddenly appear " This concludes the beta test for this software release....... blah, blah,.... guess what? its a time bomb can't do anything on screen but to reset. So I decide to re-flash it again but I got stuck at 0% on bootloader mode and got Error 262, I tried to understand whats the meaning of it and I did, but never got any solution how? I tried to flash it with HSPLWrapper_Blackstone_156OliNex to restore Winmo 6.5 but I got stuck again on 0%. something unusual I tried to reflash more roms and it didn't work. All the Roms I've wont reach 1% Even flashing on SD card trick wont load. And my spl ver 1.15 can't flash anything. So I that's why I need your help desperately...
Click to expand...
Click to collapse
If you are getting an Error 262, you need to run manual sspl in order to resolve this. Read this post for the steps (post #2) and sspl tool (post #1) - http://forum.xda-developers.com/showthread.php?t=505377. You can also get all of the steps needed to successfully flash. if you have questions, please post them in that thread.
It seems when I restart my phone normally, I noticed that the message about " This concludes the beta test for this software release....... blah, blah" the manila interface was behind it when I press the task manager and the volume buttons it responses means its not bricked (hope so) maybe the reason why I cant flash anything? Or whatever...Well that's my observation..... Please guys I needed my phone badly tomorrow
Did you not read my post . You can flash another rom, error 262 is common. You just need to use sspl before flashing to hspl 1.56.
if ur stuck with hspl and cant flash that than try uspl or try stock rom.... they get installed without hspl or uspl installed.... its available in the blackstone wiki section
and with stock rom get through tomorrow . than try hspl or uspl with custom rom later on when u have free time
Upgrade the ROM with latest official HTC release it upgrades the bootloader to ver 1.54 as well. Then you can install the newest version of HSPL or just use USPL to flash whatever cooked ROM you want.
Apologies on replying again here instead of posting on the designated thread , but forgive my innocence the thread says "" launch SSPL-Manual.exe from attachment, run it, wait until 1.07.OliNex tricolour screen says "USB" on it, then run the HardSPLWrapper_Blackstone.exe on the PC. "" how exactly that's going to be done? Currently I got the tri-color screen saying SPL-1.15.0000 and a USB on the bottom and when I flash either hspl or uspl I always end up on gray screen with a 0% that doesn't move at all, how can I manually apply SSPL? I cant access Manila interface because of time bomb message? My life's getting complicated!
If possible try flashing from an XP box, Vista/7 might give you some additional trouble if you don't use the right drivers. But if you get to the 0% screen, the issue shouldn't be with the SPL... so don't worry, I doubt the phone is bricked
So: try XP and/or using the drivers provided in the Flashing-thread
zerozed said:
Upgrade the ROM with latest official HTC release it upgrades the bootloader to ver 1.54 as well. Then you can install the newest version of HSPL or just use USPL to flash whatever cooked ROM you want.
Click to expand...
Click to collapse
I tried the Official one Blackstone_WWE_1.56.405.1 and got Error[294] Invalid Vendor ID
wayneroughneckz said:
I tried the Official one Blackstone_WWE_1.56.405.1 and got Error[294] Invalid Vendor ID
Click to expand...
Click to collapse
Did you downloaded the ROM from the HTC site? If the ROM is from the official site try again using USPL.
I seach the wiki page and found the latest version which is "Blackstone_WWE_1.56.405.1" and I can't find it on the official site, it should be "WWE" not specifying on certain countries, so I manage to download it from Rapidshare link. and for the SSPL I don't think I can do that coz I can't access my phone coz it has tim bomb probably the main culprit here.
Any flashing problems should be posted in Dummies Guide thread.
Thread closed
I have successfuly flashed my X1 and im installing costum rom on them.
But now friend came with his X1 wanting me to install custom ROM on it.
I started Hard SPL unlocker and everything gone OK until it came to bootloader mode. Windows installed all drivers without problems but progress bars on both phone and pc were at 0%. After about half minute waiting at 0% it thrown out error 626. After that i taken battery out and back in and phone boots normally with Stock SPL.
A am suspecting that problem is in Stock SPL version. I have 0.72 while in Hard SPL thread it says 0.52 and maybe Hard SPL is not supported on this version.
I have searched about 626 but didnt find any solution.
Please help.
go to olinex hard spl section and write about your problem maby they can help u
Onlinex hard spl section?
I must be blind. Where is that?
matejdro said:
Onlinex hard spl section?
I must be blind. Where is that?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=431218
go here
matejdro said:
I have successfuly flashed my X1 and im installing costum rom on them.
But now friend came with his X1 wanting me to install custom ROM on it.
I started Hard SPL unlocker and everything gone OK until it came to bootloader mode. Windows installed all drivers without problems but progress bars on both phone and pc were at 0%. After about half minute waiting at 0% it thrown out error 626. After that i taken battery out and back in and phone boots normally with Stock SPL.
A am suspecting that problem is in Stock SPL version. I have 0.72 while in Hard SPL thread it says 0.52 and maybe Hard SPL is not supported on this version.
I have searched about 626 but didnt find any solution.
Please help.
Click to expand...
Click to collapse
Just got that error yesterday while updating my Rom and OS go to Settings, Connections, USBto PC, then choose active sync and check enable advance network. You might need to reboot your host pc to recognize changes on you mobile device.
Tried both checked and unchecked and dont work
I have managed to solve it!
Problem was newer Stock SPL.
What i did is installed image that contained old 0.52 SPL and now i can finally install Custom ROMS
Great!!! I will remember that one too.