NOT SOLVED::Sound problem - Possible ROM incompatibility with MDA Compact IV? - Touch Diamond, MDA Compact IV General

Please read patiently ... I have spent many hours reading on the forum and flashing many ROM's:
I have T-Mobile MDA Compact IV, originally purchased in Czech Republic, with stock ROM version 1.37.110.3 CSE. Everything "worked fine" except for the huge memory and batery consumption
Here is what I did:
1. Installed OliNex Unsigned HardSPL version 1.40
2. Upgraded to latest SwiftBlade ROM - very nice, but I started to have problems with audio soon - after switching few of the ring/notification wav and mp3, the audio got stuck - either silent or buzzin with a high-pich tone. The same could happen when I muted ringing phone by turning phone face down. Only soft reset helped.
3. Upgraded to latest Duttys ROM - very nice as well, but had same problems with the audio.
4. Upgraded to latest panosha Shine On 1.7 - same problems again (but now I understand why there is no point in comparing ROM's, each has its own value)
5. Played with the official HTC 1.93 ROM (changed the device ID as MDA compact has DIAM200), installed it successfully, but had same problems with sound again.
6. Now here is the tricky part; as a last resort (the phone was of no use once the sound was dead ) I have returned to original T-Mobile ROM. I have downloaded and installed UK version, which is based on ROM 1.37.110.3 WWE and only updated the radio to 1.00.25.05 for better power management.
I do not have sound problems any more. However, it is hard to believe that any HTC 1.93 based ROM (original or cooked) is not compatible with MDA Compact IV. Also, I have found many people on the forum, with MDA using cooked ROMs and not reporting any problem with sound.
I apologize for the long post, but can you please (escpecially the chefs) look at the issue? There are several posts of people reporting sound problems but there was no response to it yet.
I will really appreciate your help. I want to use HTCBlack skin and any of those cooked ROM's!
EDIT - UPDATE
I have originally believed that the problem was resolved. Unfortunatelly until the first call. The phone rings once, sometimes twice, and then the sound goes out!
I have tried all possible versions of SPL and ROM (HTC Original, Diamond Project, SwiftBlade, panosha, Dutty, and more) - most of the day today - but the result is still the same.
The only possiblity to return sound is to reboot - but only until next call. You can ask my friends, they are getting crazy.
When I flash back the TMUK stock original ROM, problem does not appear, even when I upgrade the radio to 1.00.25.05. No problem at all.
Please help

I have a MDA Compact IV (from the UK) and i'm currently using Panosha Shine On 1.7 and i have no sound issues, though this is the only other ROM i have tried apart from the official!

Sometimes its the SPL which creates issues. try Different Hard SPL,s i found best to be jockys 2.4 however this only shows you have 128MB ram. otherwise very good spl.

+1
thanks,
I have exactly the same problem and it's very hard to believe that SPL can be a source. I'll try other SPL's and report here the result.

thank you
tigger80 said:
Sometimes its the SPL which creates issues. try Different Hard SPL,s i found best to be jockys 2.4 however this only shows you have 128MB ram. otherwise very good spl.
Click to expand...
Click to collapse
Surprise, but thanks for the tip. I have changed HardSPL to JockyW 1.24 and updated to SwiftBLASW ROM 6.0 and did not see any problem with audio for at least 2 hours . I consider this issue solved. Thanks again!

Many thanks to tigger80!
working great!

... by any chance have these findings been substantiated by more people? - and if so, do Olipro and Cmonex (the people who released OliPro HardSPL v1.40) know about this problem?
Just a thought.

The problem is not resolved yet
I have updated the original post. I still have a problem and can discribe it better. I have also contacted directly OliPro with request for help.

pooh44 said:
I have updated the original post. I still have a problem and can discribe it better. I have also contacted directly OliPro with request for help.
Click to expand...
Click to collapse
have anything?

Related

Orange M700 UK guide to upgrade from WM5 to WM6 + other questions

Hi all,
I have recently got my Orange SPV M700, new to this forum so apologies if these questions have been covered before. My details are as follows;
Operator version: 19.123.1.615
ROM version: 1.23.61.5
ROM date: 01/25/07
Radio Version: 1.30.00.01
Protocol Version: 32.63.7020.08H
I am wondering about several things;
1. Can I upgrade WM5 to WM6, if so, where is the ROM and how do I do it?
2. Can I make a backup of my factory ROM/settings prior to the upgrade incase something goes wrong I can reset to original state. If so, how?
3. Has anybody successfully update ROMs to WM6 on Orange SPV M700s?
4. Can anybody recommend any cool apps/games for the M700 and where I can download them from.
Thanks in advance!
Scott
Scott, can't answer the question about WM6 myself, as I am also looking for this.
As to regards to backup ROM, there is this thread http://forum.xda-developers.com/showthread.php?t=309959
just tried it myself and works a treat.
As to apps, you definitely want to get hold of the M700 Bass fix cabs, without them, the sounds if hideous. PM me and I'll email them over.
Thanks. I have updated with the bassfix cabs and it might a slight difference, although not what I would call bass. I am using the supplied earphones though. Can anyone get any decent bass sounds out of those?
Regarding your 1st post- look in the Trinity/WM6 part of this forum. There are a few versions of WM6 you can load, but unless you are willing to risk your device, stay clear until you are fully familiar with it.
Installing an unoffical ROM WILL invalidate your warranty. There are ways to backup your ROM, but if there is a major system failure, you may not be able to revert it, so beware.
There is unlikely ever to be an official WM6 ROM from Orange. though HTC are still considering it. Dopod (Asia) are testing one. These would still infringe your Orange license however.
Having said all that, it is unlikely that Orange would detect an unoffical ROM, if there were a hardware fault, because fixing it would entail flashing the official ROM anyway!
i have updated mine to wm6 and it works a treat.
you will need to install the new voice mail notifications cab though otherwise a missed call results in a text message with [email protected]
Where is the link for the WM6 ROM update?
You would need to CID unlock it 1st otherwise you wont be able to anything other than an Orange ROM.
Heres the link
http://forum.xda-developers.com/showthread.php?t=293957
I Have the Orange M700, Unlocked the SIM and the CID with help from the above link.
Flashed the WM6 from here http://forum.xda-developers.com/showthread.php?t=305133
and flashed back the original orange ROM from here http://forum.xda-developers.com/showthread.php?t=309959
Nerve racking at times but nice when its all done
Nogs
i had the exact same trinity as yours same radio & rom version & i upgraded to mUn 2.00 S.E. without CIDunlock, mUns roms come with softspl just double click the .exe & flash!
stephencurle said:
i have updated mine to wm6 and it works a treat.
you will need to install the new voice mail notifications cab though otherwise a missed call results in a text message with [email protected]
Click to expand...
Click to collapse
Do you have a link for this cab, I need to install it myself but can't find it.

HTC MTeoR WM 6.1 A4 ENG (Beta 1 - B1)

Hello all
Wm6.1 alpha 1 Ver.5.2.1711 (Build 19202.1.0.0)
Many bugs (high instability)
WM6.1 alpha 2 Ver.5.2.1711 (Build 19202.1.0.0)
Many Bugfixes (Usable)
Accesibility-working
Comm manager-working
T9-working
Power-NOT WORKING (you have to regedit)
WM6.1 alpha 3 Ver.5.2.1711 (Build 19202.1.0.0)
Many Bugfixes (Very Usable)
Accesibility-working
Comm manager-working (without bluetooth) - fix in progress (A4)
Bluetooth working - separate menu
ad2p fixed - proper version
T9-working
Power-working
Suspend -working
XIP - Rebuilded
Caller ID -working
HSPDA-working
GPRS-working
GPS-working (external device)
MMS - working
2 beam in control pannel !!!! - fix in progress (A4)
Please test and tell me if is anything wrong and if you find fixes
WM6.1 Beta 1 Ver.5.2.1711 (Build 19202.1.0.0)
Many Bugfixes
Accesibility-working
Comm manager-working (COLOR with BLUETOOTH)
Bluetooth working - separate menu
ad2p fixed - proper version
About - FIXED
T9 - working
Power - FIXED
Suspend - working
XIP - Rebuilded
Caller ID - working
HSPDA - working
GPRS - working
GPS - working (external device)
MMS - working
2 beam - FIXED
Windows Live - FIXED
you must update Windows Live to latest version
http://rapidshare.com/files/106073863/Windows_Live_10.6.34.2500.cab.html
ROM Links
http://rapidshare.com/files/105874292/MTeoR_-_WM6.1_-_A3.rar.html
http://rapidshare.com/files/106079473/MTeoR_-_WM6.1_-_B1_-_ok.rar.html
Please test and tell me if is anything wrong and if you find fixes
Also released the A4 kitchen
Many thanks to
Bepe - Tools
Mamaich - Tools
Dr Martin Gonzo - support
Garmin - support
futureshock - Test and bugreport
Hi, from where comes the Wm6.1 Roms?!
when you give it me i will try to made other languages too of it
jerpelea said:
Hello all
This is the alpha version of wm6.1
Please test and tell me if is anything wrong and if you find fixes
http://rapidshare.de/files/39013516/MTeoR_-_Splash_Screen.rar.html
http://rapidshare.com/files/98157272/WM6.1_Segoe.cab
http://rapidshare.com/files/104652554/MTeoR_-_WM6.1_-_A1_-_ok.rar.html
tomorow i will release the rom kitchen
and vanilla wm6 & wm6.1 roms
Many thanks to
Bepe
Mamaich
Dr Martin Gonzo
Garmin
for their tools and suport
Click to expand...
Click to collapse
how cook chines ROM?
good job! thanks very much!
Wow Cooooool man good job thanks
hello,jerpelea !
I find this rom in "seting", "Power Management","Accessibility" is bad."regional settings" locale is russian,and lose "systerminfo"
my english is poor,wish you can understand.
Hello lyf1998
fixed accesibility
working on power settings
i know that locale is in rus (is normal)
Where did you find sistem information ?(it is not included in this rom)
I will not cook chinese rom
please learn english, read forum and learn gow to cook or add locales.
I will release the Kitchen so that you could cook yorself an rom
Thanks
jerpelea said:
I will release the Kitchen so that you could cook yorself an rom......
Click to expand...
Click to collapse
Thanks.
呵呵,谢谢。
released
till monday i will release an A3 version
jerpelea is KING!
Hey jerpelea. Thanks so much for getting this out, I loaded it up as soon as I got home Friday night. Observations so far:-
Pros:-
-Very fast loading, much faster than latest WM6.0 out for Mteor
-Very fast running, including loading apps.
-Visually, complete makeover. Much happier with this Today screen than any plugin I've seen.
-All software attempted to far works fine- Route66, Google Maps, Skype (as well as it does on the mteor anyway!).
Issues:-
-msn messenger not installed, however Today screen expects that it is there. When selecting to sign in from Today screen, it comes up with a connectivity issue immediately, however no connectivity issue exists. I can install WLM seperately, but would be ideal to have the sign in from the Today screen as intended. Also when I've installed the latest WLM, there is a strange issue where I cannot do backspace- the 'back' key does not delete text and move the cursor backwards. Makes MSN virtually unuseable for me.
-Phone intermittently does not resume from standby- is frozen. It is still flashing to say that it's on and connected, however no buttons will revive it- the only way to revive is to remove battery and reboot. When phone restarts new messages and emails come in- leads me to believe phone was frozen.
-Phone intermittently wakes up for no reason- have had the phone sitting next to me for a night, and it lights up brightly at random intervals.
I am blown away with this release- it's made my Dopod 595 my favourite phone to carry again, over my Hermes and Asus Halley. A few issues to be resolved obviously, but it's exciting that we're getting such recent builds of WM6 for our Mteor's.
Keep up the great work, holding my breath for the A3 release!!!
does it work with dopod 595 variants with forward facing camera? and also, can you please point us to SuperCID unlock guide? thanks
Dopod 595 & WM6.1 A2
alexnvidia said:
does it work with dopod 595 variants with forward facing camera? and also, can you please point us to SuperCID unlock guide? thanks
Click to expand...
Click to collapse
It sure does work with the 595, albeit with the issues mentioned in my previous post. I'm honestly not sure about the front-facing camera, hadn't tried it yet. Will try tonight and advise.
In terms of getting around the CID issues, there will be 3 registry edits you will need to make (need to copy regedit to phone and run to make changes), and also a piece of software to application unlock. This will make your phone Application Unlocked.
You then put Des' SSPL on the phone, run it and immediately press the power and camera buttons. It will then start with the special SSPL, which gets you around the CID locking. You can in theory update via the update software (RUU) after this, however I have always upgraded via putting the rom onto the memory card as "BREEIMG.NBH". There is packaging software that will allow you to put your own choice of radio, rom, splash-screen's etc together.
In terms of the SSPL process, this is very well documented on the forum. Just take a look. I would not attempt the SuperCID process suggested- which involves loading the Hermes unlock tool to the phone. The hardware may be the same, however the command to enter the bootloader is not, I have bricked my Dopod 595 TWICE doing this- both times having the board replaced (under warranty luckily!). Up to you to attempt if you like- however I just don't see that it's really worth it until there is a dedicated and foolproof process.
Remember that these rom upgrades don't include the radio upgrade- so if you are upgrading your firmware for the first time, best to flash the most recent HTC WM5 upgrade first (incl. radio 1.38.x). Or an extracted Hermes radio rom. Just ensure it includes HSPDA.
If it's your first upgrade, and you don't like the idea of upgrading many times, I'd perhaps wait until a more final WM6.1 for Mteor is released (perhaps A3 or a RC).
I'm far from an expert, but have played with these, and my Hermes a lot. If I can perhaps answer anything else, please let me know...
MMS
jerpelea can u add MMS program to your A3 release???
stuartmclean said:
It sure does work with the 595, albeit with the issues mentioned in my previous post. I'm honestly not sure about the front-facing camera, hadn't tried it yet. Will try tonight and advise.
In terms of getting around the CID issues, there will be 3 registry edits you will need to make (need to copy regedit to phone and run to make changes), and also a piece of software to application unlock. This will make your phone Application Unlocked.
You then put Des' SSPL on the phone, run it and immediately press the power and camera buttons. It will then start with the special SSPL, which gets you around the CID locking. You can in theory update via the update software (RUU) after this, however I have always upgraded via putting the rom onto the memory card as "BREEIMG.NBH". There is packaging software that will allow you to put your own choice of radio, rom, splash-screen's etc together.
In terms of the SSPL process, this is very well documented on the forum. Just take a look. I would not attempt the SuperCID process suggested- which involves loading the Hermes unlock tool to the phone. The hardware may be the same, however the command to enter the bootloader is not, I have bricked my Dopod 595 TWICE doing this- both times having the board replaced (under warranty luckily!). Up to you to attempt if you like- however I just don't see that it's really worth it until there is a dedicated and foolproof process.
Remember that these rom upgrades don't include the radio upgrade- so if you are upgrading your firmware for the first time, best to flash the most recent HTC WM5 upgrade first (incl. radio 1.38.x). Or an extracted Hermes radio rom. Just ensure it includes HSPDA.
If it's your first upgrade, and you don't like the idea of upgrading many times, I'd perhaps wait until a more final WM6.1 for Mteor is released (perhaps A3 or a RC).
I'm far from an expert, but have played with these, and my Hermes a lot. If I can perhaps answer anything else, please let me know...
Click to expand...
Click to collapse
you sound pretty much like a guru here.. it will be very helpful if you can provide the links to the documentation of the CID, SSPL, ROM, or anything relevant here. i know i can do a search, but my 595 is out of warranty and it wouldnt want to risk killing the phone with the wrong process or procedure.. unlike the startrek thread, the superCID and unlocking process are well pointed(links) and explained in the ROM update packages. i find that Breeze's threads are a bit fragmented here..
so if it's not too much of trouble, maybe you can start a new thread explaining the unlocking, CID, SSPL, and Radio upgrades in detail. im sure the admin will make this useful thread sticky for nobs (like me). cheers.
have you looked into wiki?! there are many infos...
CID Unlocking isnt researched sofar that you can use it without starting the sspl from a running device... so that means theres no HARD SSPL yet...
and i think there would never be..
i have tested to flash devs sspl but it didn't worked...
i'm also on the side that the mteor is a smartphone thats not really widly in use... so theres no big community behind they develope!
DEv has done so much with his sspl...
and with wm6 and wm6.1 yet i think thats much more i have ever imaginaryed!
thank you again! but i still do not run rom Kitchen.
is it possible to put in the neo-plugin today app from the mteor wm6.0 roms?
lyf1998 said:
thank you again! but i still do not run rom Kitchen.
Click to expand...
Click to collapse
cant help
i have
.net 2.0
.net 3.5
visual c redistributable
windows XP sp2
Does not work on vista
BR
Hmm....
was what I got trying to upgrade...
techdev said:
is it possible to put in the neo-plugin today app from the mteor wm6.0 roms?
Click to expand...
Click to collapse
Yes but NO i will not include it
You have the kitchen you can include it if you like
This is a vanilla version
I will try to clean it of bugs
Everybody who wants an localisation or an software will have to add it
BR

Some questions

Hi!
After installing the HTC Toupad on my Kaiser, I have experienced big problems. Letters on the Keyboard (QWASYX) didn't work and even the onscreen keyboard didn't recognized these letters. So I decided to uninstall the application. But now I have other problems with my Kaiser and so I decided to Hardreset my device. But before I do this, I want to upgrade my Kaiser to WM6.1 and update it to the newest ROM/Radio.
Now I have some questions relating to that.
As a result that I am a Super Moderator in another forum I know that it is bugging if people don't read the Wiki/FAQs. I have read them, but I don't understand many things :-|
I have handled it to unlock my device, but when I was reading about updating to WM6.1, I saw only things like: "... works only with 6.1", update this, update that, and I don't know in which order.
First of all: Could anyone explain me how to update my Kaiser to WM6.1 and the newest Radio?
Secondly: What is this Duty FW? Is it a modified Rom with added apps?
Finally: I have a normal Kaiser. Not a Vario III, AT&T or something like that. Just the austrian version of the Kaiser with no brandings and so it would be good to have a Firmware without any brandings.
Thx in advance.
BTW:
ROM version: 1.56.405.5
Radio version: 1.27.12.11
Oh, I have forgotten one thing: Is it possible to change the LED blinking in the Phone Mode? To change it from green to blue?
The letter problem you were having was a simple fix with a cab that can be found all across this forum. All the ROM's can be found in the ROM Development forum and as far as what has been changed, modified, added, programs list, can all be found in the FIRST or SECOND post of each of the ROM's. So you will just have to read through them and find one that suits you best as they all have something different. Most of the radio's that can only be used on 6.1 ROM's will say "Will only work on 6.1 ROM's". And I would like to add even though you don't have at&t DON'T FLASH THE 1.65.17.10 RADIO.
KDKobes said:
The letter problem you were having was a simple fix with a cab that can be found all across this forum. All the ROM's can be found in the ROM Development forum and as far as what has been changed, modified, added, programs list, can all be found in the FIRST or SECOND post of each of the ROM's. So you will just have to read through them and find one that suits you best as they all have something different. Most of the radio's that can only be used on 6.1 ROM's will say "Will only work on 6.1 ROM's". And I would like to add even though you don't have at&t DON'T FLASH THE 1.65.17.10 RADIO.
Click to expand...
Click to collapse
Ok, thx first of all. Dutys rom sounds nice. What do I have to do first? It is still a little mystery for me ^^
alcbottle said:
Ok, thx first of all. Dutys rom sounds nice. What do I have to do first? It is still a little mystery for me ^^
Click to expand...
Click to collapse
You need to make sure before you flash a rom on to your kaiser that you flash hardspl - http://forum.xda-developers.com/showthread.php?t=334679, and than after successfully installing that you can flash the rom of your choice. Please read the first sticky thread under the kiaser rom development form - http://forum.xda-developers.com/showthread.php?t=369282; it has all the info you need pretaining to everything involved when it comes to flashing your kaiser. I strongly recommend you go through it and read the posts it points to that are relevant to flashing.
Once you have done that it is pretty simple process; just do yourself the huge favor and don't flash until you have flashed hardspl or you will brick your phone.
If its still a mystery I would start here http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
No pun intended.
@thesire
I have already installed HardSPL. Otherwise I couldn't have unlocked my device with this method: http://forum.xda-developers.com/showthread.php?t=361039
I have used just the Sim Unlocker Method. Not the Kaiser SIM/CID Unlocker & Changer
That's the reason, why my mobile phone is now with an english language
Just one important question: Do I have to change my current radio for the new Duty Release?
@KDKobes
Why shouldn't I flash THE 1.65.17.10 RADIO?
Some ROM's come with radio's some don't. Most of Dutty's ROM's come with radio's, but if you want to keep your radio then I would suggest finding a ROM without a radio in it or making sure yours is compatible with the WM 6.1 and reflash it back. The 1.65.17.10 radio will lock your phone to that radio only and you will not be able to change it until somebody can fix it. Alot of people are stuck with that radio now and can't change.

Dumping standard shipped ROM

Is there anyone who has succesfully dumped the Official Shipped ROM that comes with the European models ?
I'm sure that apart from me, there are other members who would like to revert to the offical ROM just in case something happens with the device. (need to send it back for a reparation)
I'm going to flash just right now anyway, as I'm positive that there will be someone in the future dumping the offical ROM.
\cheers, now pressing start
EDIT : After flashing I keep the high pitched noise that almost everyone is Reporting. I can't get rid of it. Be aware with this ROM,. you might get stuck with a hissing device that won't stop I'll wait for some solution and then flash again, can't use Winmo anymore
me too...please help us - i cannot use my device due to constant noising...
up0grading the EC chip drivers
I saw some remarks about the EC Chip driver update from HTC - will try that now, see if it helps anything at all.. For now, the device always hisses like a snake when Vista is active.
Without Vista active, it's mostly quiet, but gives no sound in WinMo, however, if you try to make a sound in WinMo, sometimes, after a few seconds, it will hiss and pitch for the duration of the sample played...
This is really annoying
hi,
i did a backup pof's way, so i have now part00.raw - part04.raw and SPL.nbh.
Rebuild Part02.raw and uploaded again. Working like a charm. Problem is: my original ROM is in German. anyone interested?
german but quiet is much better than english with noise.
please provide links.
Thanks
GERMAN..?
That sounds wonderful: need the the german ROM very urgent, can`t work with my beloved shifty...
Please share the ROM, thanks so much!
Me too!
I installed the GPS Bios pack - Easy BUT:
The noise only appears while staring after reinstalling the battery - just restart SnapVue after Vista is up and the noise is gone.
Also gone is the German keyboard under SnapVue - Regional settings don't change that!
GPS work in SnapVue and Vista (using ActiveSync & GPSgate - after test period ~30€).
Overnight SnapVue need app. double the energy than before!!!
Using GPS in Vista means NO internet/mail!
Wrong keyboard layout and battery drain tempt me to reinstall an original German ROM and to continue using my dear old eTrex with USB together with my Vista progs.
So, how and where2 can I find the German ROM?
Thanks,
Axel
Send the Rom-Link to a victim already. Waiting for an OK before i publish.
Victim report Nr. 1:
@tece: Thanks a lot, man, good job, it works fine..!
Regards and thanks a lot.
Alex
great!!
i noticed that pocketie is already installed and that \Windows\StartUp\PKG.exe and BlockTitleBar.exe are already removed.(like i did as described in this: http://forum.xda-developers.com/showthread.php?t=377441 thread before backing up the original ROM). Now I'm looking to get the registry preconfigured to not start Snapvue. Liberated German ROM will get released this weekend. If you can't stand waiting for that ROM send me or traumrakel a PM for the rapidshare link.
If you could include the liberation into the new ROM I would prise your name... ;-)
and here it is: http://forum.xda-developers.com/showthread.php?t=417901
I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?
cmonex said:
I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?
Click to expand...
Click to collapse
hello cmonex,
i m running the german rom as i do not have my original french dump, i would be very happy to install 1.30 WWE!!
even if tece rom is great in order to learn some german word
cmonex said:
I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?
Click to expand...
Click to collapse
Do you have the reconstructed ROM of version (original UK Shift): 1.30.405.0 WWE ? Can u post it/send it? Then I don't have to rebuild it myself, because I'm not that experienced it rebuilding myself. Also in case my rebuilded rom fails to work.
Many thanks!
cmonex
Could you please share the 1.30WWE
Thanks
Ram
You have it, it's the one having gps and sound bugs with european radios.
I'm using 1.22 because it's a stable base. Later version doesn't give you much, as graphic drivers are disabled anyway.
thaihugo
Cool. I followed pof's suggested way of dumping the original rom. Now I got all the raw files with correct start addresses. I am wondering whether I did correctly or not for SPL.NB. because the file size is 256 KB since I passed the same length 262114 as read in pof's post. When I used KaiserKitchen to reconstruct, I don't have baseRom and if I ignore that, I am not gettting the NBF file. I want to backup my CHT ROM and install your's (1.22 with GPS and sound). Could you please shed some light?
Thanks
Ram
Hi Cmonex ;
I need the non-touched 1.30 WWE rom for shift ; can you share please ?
Safak
Thaihugo , Saiweb
Do you have 130 WWE non-touched original rom ? I ve downloaded one from the forum but it is the "telenav"ed orig one , which i can not use at all...
Can you share if you have ?

Audio input/output issues

Heya,
i have an MDA Vario III and i have recently updated to a new rom.
i used the newest HardSPL to date (3.xx) and a custom cooked rom.
my real problem though was after i updated to OliProf the audio iput/output would completely cut off. i found it was the radio rom, so i updated it AFTER i updated the hardSPL and rom, (i have 1.27.12.11). the sound worked fine after i did all this for a week or two, but now the sound has started stopping again, the only solution is when i flash the radio rom, but the sound would then cut off after 3/4 hours, meaning i have to reflash the radio rom every 4 hours
any help would be greatly appreciated
Poly
All newer ROMs are WM 6.1-6.5 so need the radio to match so you should be using a WM 6.1 Radio and not a WM 6.
The Ultimate Radio Thread
so what i should do is really is go through and try all the radio roms under W6.1? because even after reading, i am still confused as to which rom i should use to update, sorry ):
and FYI i found out that the rom im using at the moment is "THE AMAZING 23001 ROM by DJKOA"
and the SPL is 3.56 HARD
Go with the recommended radio "mind u i think that it's not matched" read the thread from back as sure posters have mentioned radio issue, then you will have phone working and from there only you can find the best Radio as it depends on so many variables location\carrier etc and effects battery life\data\GPS Fix.
And on another note H-SPL 3.34 is recommended for 6.5

Categories

Resources