Subject No such standard function
Stardard has ring after vibration, but after ring started there is no vibration... but i need ring and vibration after vibration only...
On my Diamond I can edit it in registry (I'm not sure that it's always RingTone0):
Key- [HKEY_CURRENT_USER\ControlPanel\Sounds\RingTone0]
Entry - "Script"="v2w3v2c20av0pc250r"
In my example it vibrates twice and then vibrates and rings with increasing ring
For details about script's codes see wiki:Registry Ringtone Scripts
Good luck!
What if i just want 3 vibros for 3 seconds, and then usual vibro and full call ring?
try:
av1w0.1v1w0.1v1w0.1v0p10r
nice, about delays between vibro and vibro duration - i can hadle it
one problem exists after RING played - it goes back to 3 vibros...
try:
v1w0.1v1w0.1v1w0.1av0p10r
or maybe so ( with 2 sec delay between each repeat ):
v1w0.1v1w0.1v1w0.1av0p10w2r
i have done such thing:
av1.5w1v1.5w1v1.5w1v0pr
how to make that after ringing begin it will play 5 seconds with 25% percent volume, then 5 seconds with 50% and then rest the time at 100%?
NOT REPEATING RING FROM beginning i.e melody
Related
I've had a Tilt for a few weeks and starting to love it. Previously I had a Blackberry and I loved being able to have both vibrate and sound simultaneously to notify receiving a call. Anyone able to do this on the Tilt/Kaiser?
Vibrate then or and ring on Tilt
It is possible to have the phone vibrate and ring simultaneously or vibrate then ring.
Start - Settings - Phone - Ring type (vibrate and ring)
runuts said:
It is possible to have the phone vibrate and ring simultaneously or vibrate then ring.
Start - Settings - Phone - Ring type (vibrate and ring)
Click to expand...
Click to collapse
Sometimes I just can't help but feel like an idiot... Thanks...
Does anyone know of a programme to activate intermittent vibration? The continuous is a bit annoying. Thanks.
Has anyone else seen an issue with the ATT Tilt where it will vibrate to indicate an incoming call or email and lock up (still vibrating) until the user either removes the battery or the battery just dies and the unit resets? I work for an organization and have had two different units do this on multiple occasions. The second one was recently RMA'd and replaced and has only been back in service a few days. We are running the factory ROM which may be part of the problem, but I hate to send these guys out with anything experimental. Any help/advice/co-misery would be appreciated.
Cant say this is something i have come across with my many ROM's flashed onto the kaiser. Sounds like just a bit of bad luck to me
nitrofreak said:
Has anyone else seen an issue with the ATT Tilt where it will vibrate to indicate an incoming call or email and lock up (still vibrating) until the user either removes the battery or the battery just dies and the unit resets? I work for an organization and have had two different units do this on multiple occasions. The second one was recently RMA'd and replaced and has only been back in service a few days. We are running the factory ROM which may be part of the problem, but I hate to send these guys out with anything experimental. Any help/advice/co-misery would be appreciated.
Click to expand...
Click to collapse
Have not seen this reported for a while now, but see here:
http://forum.xda-developers.com/showthread.php?t=348042
You may want to consider changing the vibrate ring string to avoid the third vibrate that appears to cause the lockup.
Change ringtone/vibrate/LED flash characteristics
If you would like more control over how your device rings/vibrates/flashes its LEDs on events, you can can change the Script values of these events. For example, for an incoming call performing 'activate device, play ringtone, wait 3 seconds, repeat':
HKCU\ControlPanel\Sounds\RingTone0\Script = "apw3r" (REG_SZ string, no quotes)
For performing 'active device, set volume to 33%, play ringtone, set volume to 67%, play ringtone, set volume to 100%, play ringtone (no repeat)':
HKCU\ControlPanel\Sounds\RingTone0\Script = "ac33pc67pc100p" (REG_SZ string, no quotes)
The following are the full codes available to you. Please note that all the codes are executed simultaneously except after a ringtone play / wait code. E.g. 'v1p' will vibrate and play at the same time, while vibrating for 1 second. But 'pv1' will play the ringtone through all the way first, then start vibrating for 1 second.
a = activate device
cN = set volume to N in percentage max volume
fN = flash notification LED for N seconds
p = play ringtone. Note that this will play the ringtone all the way through before continuing with the next code.
r = repeat. Note that this should be the last code in your Script string, if used at all.
vN = vibrate for N seconds
v0 will vibrate continuously;
v3 will vibrate for 3 seconds;
v3p will vibrate for 3 seconds, then play the ringtone;
v0p will vibrate and play the ringtone at the same time, and when the ringtone stops, the vibrating stops as well;
v0p3 will vibrate and play the ringtone at the same time, and stop after 3 secondwN = wait for N seconds. Note that the device will wait this long before continuing with the next code.
Some more examples
Display - a
Flash - af1w60f0
Ring - apw3r
Ring Once - ap
Increasing Ring - c50apw3c150r
Vibrate Then Ring - v3w3apw3r
Vibrate - av3w3r
Short Vibrate - av1w3r
Vibrate Long Then Ring - v3w3v3w3apw3r
Vibrate And Ring - av0pw3r
Increasing Ring And Vibrate - c50apv3w3c150r
Fast Vibrate And Flash - af1v1w1f0r
There are several notification sound settings in the registry – examples:
[HKEY_CURRENT_USER\ControlPanel\Sounds\RoamingRing0]
"Script"="apw3r"
[HKEY_CURRENT_USER\ControlPanel\Sounds\KnownCallerR ing0]
"Script"="apw3r"
[HKEY_CURRENT_USER\ControlPanel\Sounds\RingTone0]
"Sound"="\\Storage Card\\My Documents\\Trout.wma"
"Script"="av0pw3r"
Mike
I set my diamond to ringing and vibration mode when someone calls. Is there a way to make the vibration stopped for a while and continue instead of making it vibrate the whole time while the ringtone is ringing? Something like making those types found in Nokia handphones
no one?
HKCU\ControlPanel\Sounds\RingTone0
Set Script to v1w1v1w1v1w1c50apw3c150r or use cab file below.
doesnt do the job. It just set my ringtone to vibrate and then ring...Tried changing it back to vibrate and ringing...remains the same. Phone kept a constant vibration and ringing when a call comes in.
Is there a way? I have a few ringtones which would sound great if the loop would repeat right after the ring finishes, instead there is a 2-3 second gap between rings.
Anyway to shorten the delay between the rings?
Hello,
My Nexus6 Rings and Vibrates when someone calls for the first time. But only vibrates when the same person calls for the second time. From the second time onwards it doesn't rings, but only Vibrates.. If I delete the history of that particular incoming call from the Recents, then it will start ringing. Please let me know how can make the phone ringing all the time.
Thanks.
An update to this issue is:
When a call arrives multiple times with in 2 minutes, the phone gives a ringing sound for all the attempts. After 2 minutes of last attempt, the phone goes to a muted mode (only vibrates). The muted mode continues for the next 10 minutes. After 10 minutes, if a call arrives from the same number, the phone rings.
Is this a standard behavior in Android phones ? Or is there a setting to make the phone ringing all the time ?