Just got a used unit for my wife with warranty for 7 days.
On the same day flashed Des-Prof HardSPL and a cooked ROM.
Later the next day the USB port can't connect to PC anymore, maybe due to some broken pins inside. So it is quite difficult to flash Original ROM from PC , especially SPL which must go through SSPL and PC USB Flashing.
This is what I did and successful;
1. Extract OEM ROM content using nbh extract tool.
2. Pack using hrt Rom Tool the SPL.nb and Both Splash.nb and build the .nbh file using htcrt ROM Tool. Name this nbh file to TRINIMG.nbh and copy to Mini SD Card which had been formatted with FAT32 earlier.
3. Copy SSPL to any location on device main.
4. Insert the Mini SD Card .
5. Now, run SSPL on the device, it will start flashing like normal ROM Flashing. It takes few seconds to complete and finally it just stuck at the infamous 3-colour screen. No matter what I did it just stay there ( phone already bricked !). But the bootloader shows original SPL, no more hard SPL! So, reverting back to Original SPL already success and happily done.
4. At this bootloader tri-colour screen,I just flash original RUU_Signed.nbh which its name changed to TRINIMG.nbh using Mini SD Card.
So happily done and will return back tomorrow to the seller for warranty purpose.
How to flash stock ROM
I broke USB on my device too.
How do you flash ROM from tri-color screen?
Do you push any buttons?
yes ,just insert the card with TRINIMG.nbh.
Hi,
I have one of the USB pins broken so I need to use this method to bring it back to the original state.
I have two doubts that it could be quite helpfull in anyone confirms them:
1) Can I flash directly from a cooked 6.1 WM to the old 5.o Vodafone one or do I need to pash to a faman 3.3?
2) in the wiki says that I need to use a miniSD but I have a micro SD with adaptar. Is there any way I can do it with a microSD?
Thanks a lot,
I use microsd with adapter too for my case,seems no problem.
Flash the stock ROM first then flash Stock SPL which was packed together with splash in.nbh.
edywanwan said:
I use microsd with adapter too for my case,seems no problem.
Flash the stock ROM first then flash Stock SPL which was packed together with splash in.nbh.
Click to expand...
Click to collapse
Thanks for the info.
Hi edywanwan,
thanks for advise
Now my Trinity is clear to be send back to the vendor. I hope never to see it again.
I tried it several times without success, but here is what I've done:
1. Extract SPL.NB from original ROM
2. rebuild SPL.NBH. Both, 1. and 2., done with NBHUtil
3. Copy new SPL.NBH and SSPL-TRIN.exe to root of SD-card (no other .nbh file)
4. Try starting device with Windows (O.K. this is the hardest part )
5. Start Fileexplorer, navigate to SD-card and start SSPL-TRIN
The device will fall to Bootscreen (3 colors), flash new SPL and that's it. Connect it to USB (without restart) and reflash the wanted ROM. Voila, original configuration
Related
Hi guys, got a problem here. Need to return my HTC Touch HD for warrant purposes, basically the USB connection doesnt work - it charges but nothing else, 3 PC's and 3 leads wont even acknowledge that its connected to a pc (yet it charges?!?).
To return it, i need to restore standard ROM and SPL but obviously because of the problem i cant connect it to a pc to flash!!
Any ideas appreciated!!
If you got HSPL you can copy the blacimg.nbh on sd card and let the bootloader flash.
Im not sure but i think it should be possible with non hspl if you flash a stock rom because spl/ipl are included to shipped roms.
Ulti
Ultimaex said:
If you got HSPL you can copy the blacimg.nbh on sd card and let the bootloader flash.
Im not sure but i think it should be possible with non hspl if you flash a stock rom because spl/ipl are included to shipped roms.
Ulti
Click to expand...
Click to collapse
As already said, you can flash the stock rom from your SD card, by copying the .nbh file into the root directory of your SD card and renaming it BLAC_IMG.nbh. Power device off, press and hold the volume down key, and press the power button to get into bootloader. The image file will be shown on the screen - just follow the instructions.
However, this will not flash the SPL as HSPL is protected from being overwritten. Not sure how you can get around this one without being able to use USB.
According to the HSPL thread, the HSPL is protected to be overwritten, so flashing SPL without the restoration pack in HSPL thread should not work.
I recommend you back up all your data and do a Hard Reset, then try to sync with your PC.
If it still not work, eject your SD card and try power on your phone while holding VolDown, this will enter the bootloader (tri-color screen). Connect the USB cradle, when the bottom of the screen shows "USB" instead of "Serial", launch the Stock-SPL restoration pack from the HSPL thread and follow the instructions.
maddie said:
If it still not work, eject your SD card and try power on your phone while holding VolDown, this will enter the bootloader (tri-color screen). Connect the USB cradle, when the bottom of the screen shows "USB" instead of "Serial", launch the Stock-SPL restoration pack from the HSPL thread and follow the instructions.
Click to expand...
Click to collapse
Tried this but it still showed 'Serial' after i connected the USB lead!
Using the SD card method im gonna be able to get a stock ROM back on there so thats a start!
I've got HSPL not USPL
Anyone know how strict HTC UK are at checking warranty returns?
More issues!!! I cant even use the SD Card method, i formatted my card and copied BLACIMG/BLAC_IMG (2 guides named the file differently) to the root of the card, when i go to boot loader it says image not found. WTF???
The file must be named BLACIMG.nbh. Furthermore it seems that some cards don't work, so maybe you have bad luck .
But, as already said, this doesn't help you at all, as you need to restore the SPL, too, which isn't possible without an USB connection.
what was the outcome re your phone?
Jade Flashing Guide for NOOBS
Pre-Requiste
1) You need Jade-Hard-SPL_V3 for OEM 1.40.** builds / Jade-Hard-SPL_V41 for OEM 2.32.** Builds -> Get it from here <- Follow instructions in the thread
( How to Know Your SPL -> Switch Off Jade, Then Press Volume Down key, then Press Power Button. Now you see Tricolor Bootloader Screen showing your SPL number)
Preparation
1) Download the ROM in the first post posted by CHEFs
2) unzip the NBH file into a folder - ( RUU_signed.nbh <- Name and Extension should be this, do not change it)
3) Put CustomRUU (get from here) into the same folder of NBH file ( as of step-2)
Method-1
1) Switch off your jade by pressing power button
2) Go to bootloader by pressing Volume key down first then power button
3) You see tricolor screen saying SPL 2.32.olinex (If you don't see this then Follow Hard SPL procedure as per procedure here)
4) Connect your Jade using USB cable to your system
5) You should see USB in the Jade Screen
6) Run CustomRUU
7) Follow instructions given by CustomRUU
Method-2
1) Synchronize your PC thru Activesync (Get it from here and install in your PC if your PC don't have)
( For Vista users-> ActiveSync can only be used when flashing with Windows XP PC, with Vista PC you need Windows Mobile Device Center from Get it from here ) <- Thx to Nirak
2) Once your Jade is synchronized then run CustomRUU
3) Follow Instruction given by CustomRUU
Flash Issue Recovery
If you accidentaly disconnect Jade from PC during flashing.. just follow onscreen CustomRUU instructions in you PC
If your Jade Struck (flash % stays at some number and no progress for quite some time) during flashing.
Check your HardSPL version and the ROM OEM build version, Hard SPL should be 2.32.olinex for OEM 2.32.** builds, Hard SPL should be 1.40.olinex for OEM 1.40.** buildsIf above is checked, then Switch off your jade by removing battery
Then follow Method-1
If your Jade is JADE110 SPL 1.70.** then install HARDSPLV41 as per instructions in Thread post#18
How To Hard Reset your Jade
Soft Method
1) Start Menu -> Settings -> System -> Clear Storage
Using Hardware Keys
1) Press Volume down key then press confirmation key (middle button near Navigation Keys) then Press Power Key. Follow on-screen instructions
HOW TO FLASH ROM ON JADE FROM THE SD CARD (Thx to Haree) (Original Thread)
1. Rename the .nbh file of your rom of choice to JADEIMG.nbh, drop into the root of your SD card.
2.Poweroff your phone
3.hold the volume down key and while continuing to hold it power on ur phone
4. The Phone will go into the bootloader mode, and will auto detect the rom image from the SD Card and ask if you want to proceed by hitting the power button. Hit the power button and the rom will install
Note : it should take about 10-15 mins
also make sure that ur SD card is Fat32 or format the same to Fat32 & use a smaller memory card the smaller the better
this is as per my experience using the above method on my previous phone ie gene(P3400i)
How to DUMP your STOCK ROM -> Read Here
To Restore a DUMPED ROM -> Read Here
German tutorial can be found here: http://www.youtube.com/watch?v=fV2I2WAFkg4 Was tun wenn ein ROM Update fehlgeschlagen ist? HTC Wiederherstellen. Thanks to Dam79
Q & A
Q: Do I need to remove sim and sd card or not? (By ilovetouch)
A: Not Necessary
Q: Unable to turn off Antivirus..? Antivirus deletes customRUU.exe (by welshbloke70)
A: 1) unzip any stock ROM to a folder
2) copy your Cooked RUU_signed.nbh to that folder replacing the STOCK one.
3) Now Run the Romupate utility
Experts please post additional instructions if missed in above post.
Thx to UDK,Olinex and other xda-developers.
Just a quick one, does it make any difference if I have HardSPLv41 for an OEM 1.40.** build? What effect does it have, if any?
TIA!
izzyzc said:
Just a quick one, does it make any difference if I have HardSPLv41 for an OEM 1.40.** build? What effect does it have, if any?
TIA!
Click to expand...
Click to collapse
should ok..
@ironeagle
thanks for the step by step guideline, thats really nice.
Best regards, ojessie
nice german tutorial in german can be found here:
http://www.youtube.com/watch?v=fV2I2WAFkg4
Was tun wenn ein ROM Update fehlgeschlagen ist? HTC Wiederherstellen.
Very nice
Stickied.
Dave
DaveShaw said:
Very nice
Stickied.
Dave
Click to expand...
Click to collapse
Thanks buddy
Question: Do I need to remove sim and sd card or not?
Thanks for suggestion.
ILoveTouch said:
Question: Do I need to remove sim and sd card or not?
Thanks for suggestion.
Click to expand...
Click to collapse
Not necessary..
Hello,
What is the version of the HARD SPL do i need with a 1.71.73.11 Rom ?
thx
Romain
cut38300 said:
Hello,
What is the version of the HARD SPL do i need with a 1.71.73.11 Rom ?
thx
Romain
Click to expand...
Click to collapse
go for V41
Dear ironeagle
Question: If sim removal is not neccessary. How's going on if someone 's calling or messaging me whilst flashing?
a) flashing paused and continue after end call.
b) flashing paused and device bricked.
c) still flashing coz the phone can't recieve anything whilst flashing.
d) .....
Thanks again.
ILoveTouch said:
Question: If sim removal is not neccessary. How's going on if someone 's calling or messaging me whilst flashing?
a) flashing paused and continue after end call.
b) flashing paused and device bricked.
c) still flashing coz the phone can't recieve anything whilst flashing.
d) .....
Thanks again.
Click to expand...
Click to collapse
(c) .........
I am getting the error "server appears to be down, try later."
I had 1.71 rom, and tried HardSPL V3 and HardSPL v1.41, both gives an error
Downloaded CustomRUU from image version 1.40.723.2, with the rom in the same folder, boot to tricolor screen and later showed a grey background with a progress bar stuck at 0%. It never moved even after 10 mins, whats wrong with this?
Alphas said:
I am getting the error "server appears to be down, try later."
I had 1.71 rom, and tried HardSPL V3 and HardSPL v1.41, both gives an error
Downloaded CustomRUU from image version 1.40.723.2, with the rom in the same folder, boot to tricolor screen and later showed a grey background with a progress bar stuck at 0%. It never moved even after 10 mins, whats wrong with this?
Click to expand...
Click to collapse
First you should successfully do HardSPL then try flashin ROM. without hardSPL u cannot Flash any custom ROM.
Should Read the HardSPL thread carefully..
Check ur internet connection ( No Proxy )
Install the Software in your Jade when Directed by HardSPL
I did the HardSPL, but I dun know why the tricolor screen still shows 1.40.0000 instead of 1.40.1000.
not running ny proxy, on SNBB.
Touch 3G devices. for JADE100
can I ask what a rom is best for jade? I prefer speed and stability. Sorry for my english, she is not good.thanks
why isit that HrdSPL keep telling me tat the software is for non comercial use only, and I couldnt even flash the bootloader!
IronEagle,
ActiveSync can only be used when flashing with Windows XP PC, with Vista PC you need Windows Mobile Device Center from here:
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center-download.mspx
Nirak said:
IronEagle,
ActiveSync can only be used when flashing with Windows XP PC, with Vista PC you need Windows Mobile Device Center from here:
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center-download.mspx
Click to expand...
Click to collapse
Thx buddy.. added in the 1st post..
I been study whole day in the forum also didnt found anyone fail in flashing Xperia X1.
I got a Xperia X1 accidentally flash rom without flash to HardSPL.
Now the phone is power on just will goto the BootLoader mode (TriColour Screen),
But if i plug in the USB cable connect to PC then it will goto normal.Must every time need to do that way only i can use Xperia X1.And the bigger problem is when i plug in the USB cable the X1 and PC wont be connect and even i can't charge battery also.Because of the failure connection by USB i totally can't flash X1 by USB.
I really need help in this problem,hope anyone or any ROM maker help me this problem.
THX....
Try to flash your phone again with a stock rom (you can find it in the rom section) using the SDcard method
I been try to flash the stock rom UK R1AA0017 and UK R2AA010 the problem still remain.Any other idea?Anyway thank you Mopral helping me.
hao_nam1 said:
I been try to flash the stock rom UK R1AA0017 and UK R2AA010 the problem still remain.Any other idea?Anyway thank you Mopral helping me.
Click to expand...
Click to collapse
try and use the sd card method to flash a stock rom..since your phone is booting the bootloader it shld be able to pick up the rom, hope u get it fixed
While in the boot loader (tricolour screen)
- Copy your RUU_Signed.nbh ROM file to the CustomRUU folder (where you have ROMUpdateUtility)
- Run "ROMUpdateUtility.exe"
- Connect your phone to the PC, text at bottom in tricolour screen will change from Serial to USB
- Follow on-screen instructions, loading bar shows on PC & phone
lakeside00
I been try to flash the stock rom by sd-card,problem remain only.
Musse_1
Friend my problem is i totally can't connect my phone in pc.No connection between them.That why i only can use sd-card to flash.
Guys i been flash R1AA0017 and R2AA010 rom in my phone by sd-card also can't work,problem remain.
No PPL willing to help me about my problem?
Can i asking a stupid and crazy question?
Can i flash Hard-SPL by SD-Card?
Will any things happen if i use this way to flash Hard_SPL?
Plz get someone give me a idea about my case.....
you can try but as your own risk.
extract the kovsimg.nbh to sd card root directory
HSL_SD_download
Hi,
i've a big problem with my diamond
it starts normally, but after htc splash screen, it tries to load windows but after 1-2 seconds it restart.
i was using cooked rom gen.Y D2 rev.Y with radio 1.09.25.23
G 52.51.25.26H
i've tried with original rom 2.03 but the problem still remains.
What can i do to resolve this problem?
Where can i find original radio and G (what does it stand for?) to put inside my htc with original rom for probably warranty assistence (i hope)
i've also olinex1.40 spl, how can i remove it?
Thank you in advance
Gianluca
SOunds like a bad flash to me. Try using MTTY to reflash. Should work fine
http://forum.xda-developers.com/showthread.php?t=540290
how can i run this procedure:
Connect Device to PC via Active Sync, Once Connected Uncheck USB Connections,DISCONNECT DEVICE then Reboot Computer
if the device can't start completely?
Flash from your System not the Internal Storage. Read the 4th post.
i can't install drivers on my win7 x64 because i can't follow the first post "how to install drivers" so with the mtty.exe it doesn't find the usb driver
In that case see if you can get into bootloader.
(Reset + Hold Vol Down), this will show the Red, Blue, Green screen showing "Serial"
Then plug your usb cable in and you should get it showing "USB".
You then need to Hard SPL and reflash.
yes i've succesfully installed drive on win7 x64
i've run mtty.exe, followed the instructions, all ok.
then i've disconnected the diamond from usb and made an hard reset (it says press vol.up to restore manufacturer default, vol. down to restore and format movinanand, i press vol. up, and after vol.up again: is it the hard reset or is it another menu?)
but after restart the htc has same problem..it continues to restart by itself
i've decided to return htc to stock software and firmware in order to send him in warranty to delaer.
so, i've installed last official rom htc 2.03, it includes the radio.
Now after that, because system doesn't want to start completely, also after mtty.exe format ecc., the last thing i've to do is install official spl right?
i've found the guide:
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
1. download the stock spl package from this post (pick one of the attachments) in this thread.
2. also download the RUU-SSPL-withoutNBH.zip from the attachments in this post.
3. pick the SPL you want to reflash to (ONLY FOR WARRANTY REASONS), it's a .NBH file, put the NBH in the extracted RUU-SSPL-withoutNBH package.
4. run the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to black screen), it goes to 100%, reboots, done.
+5. to verify, volume down + reset, see version number on tricolour screen.
that's it.
what official spl have i to install? 1.23 1.34 1.37?
i've tried with all the 3 spl but nothing changed i think, because when i open the bootloader it still saying 1.40olinex
Hi guys
Originally i had a HTC touch pro 2 from Vodaphone with win6.1 i tried to put the new energy rom on by following the guide here:
(flashing via activesync)
http://forum.xda-developers.com/showthread.php?t=550540
with this
ROM:
EnergyROM_21876_RHOD500_24.Nov.2009_Standard
it goes past the start up screen "Touch pro 2" and then it stops on with a white background, at the bottom of there screen it displays
B 80
R 4.49.25.17
P 61.44tc.25.32U
D Energy ROM
the multi colour screen info shows
RHOD100 32M ss-BC
SPL -0.85.0liNex
MicroP(LED 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
508,533 800,851
800,208 209,208
217,852 CALIBRATED
can someone help me recover this plz its a new phone
Thanks in advance
once at that final screen,
plug in usb
once your computer has installed drivers, it will say usb instead of serial at the bottom of the phones screen.
try flashing again,if that fails try a different rom or redownload, its not bricked your at bootloader
if you still struggle use the search feature of this site, you will find everything you need
cheers steve
rosebud said:
once at that final screen,
plug in usb
once your computer has installed drivers, it will say usb instead of serial at the bottom of the phones screen.
try flashing again,if that fails try a different rom or redownload, its not bricked your at bootloader
if you still struggle use the search feature of this site, you will find everything you need
cheers steve
Click to expand...
Click to collapse
or try flash using SD card
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
cheers
indra9110
Pheeew thats a relief panic mode off now
Thanks rosebud and indra9110 for your fast replies, I got it working rosebud's way.
I downloaded the rom again and it works perfect now,
I've also got iskoot working (which was NOT working on the vodaphone 6.1 rom)
Thanks again guys
Glad to hear your phone has come back to life