Related
Hi I have a dopod D810 i would like to know how you get the gps working on this model, can someone please help me
I did upgrade rom to 1.23.707.6 and install a TomTom program but it still looks for gps device
does the D810 have a device built in
has anyone done this Thanks
cheers
tomtom works on my aussie D810 with the same rom...
I set the GPS reciever to other NMEA GPS reciever.
coldstart it can take a minute or more to find the signal.
try standing outside in a area with a good wide view of the sky, or even driving round.
Speedn
Depending on the version of/locked files (Search forum) TOMTOM, you might need to configure it each time.
In 6.02 and below you need to select the NEMA (or whatever its called).
In 6.03 they have a selection of inbuilt GPS device. I Found 6.03 much less hassle to be honest.
how do i get 6.03 please
how do i get 6.03 please
to get tomtom 6.03 update go to the following site and follow their instructions...
http://www.tomtom.com/support/solution.php?GID=3&PID=1401&SID=0&CID=215&Language=1&FID=6736
NOTE: you will need reactivation of your maps after this upgrade to 6.03
please if anyone can help
i have a d810 have installed
rom 1.23.707.6
radio version 1.35.00.11
protocol 32.68.7020.10h
installed tomtom6
selected nmea gps
it asks baud rate
i left it at 4800
it then comes up with
com3:
gps in com9
com7:
ril on com6:
s2410 IRDA
usb Cable:
??????????? i have no idea which to pick i selected com3:
for instance and it says no gps device
i select gps in com9
it says waiting for vaild signal but never finds anything
srsjason2040 said:
i have a d810 have installed
rom 1.23.707.6
radio version 1.35.00.11
protocol 32.68.7020.10h
installed tomtom6
selected nmea gps
it asks baud rate
i left it at 4800
it then comes up with
com3:
gps in com9
com7:
ril on com6:
s2410 IRDA
usb Cable:
??????????? i have no idea which to pick i selected com3:
for instance and it says no gps device
i select gps in com9
it says waiting for vaild signal but never finds anything
Click to expand...
Click to collapse
Are you outside with clear view to the sky? Wait 15 Minutes there! It WILL work.
You're on the right track with GPS on COM9 if you are not using version 6.03. If you get as far as "No valid GPS signal" message then that means your GPS receiver is tracking satellites ok and you're just not getting a GPS fix. I had the exact same problem as you.
1) Just restart your d810 (stylus into the small hole on the underside of your dopod )
2) Start your TomTom and use the same setup as you did before with NMEA.
3) Select GPS on COM9
4) When you get the "No valid GPS signal" message stand outside where there is lots of open sky (if you're in the city... tough luck it would be really hard to get a GPS fix there).
5) Be prepared to wait for up to 15 minutes until you get a GPS fix. Mine took more than 10 minutes.
Got it working plus more
Thanks guys you have been a great help
i updated my tomtom software it was easy
as advised i went to here
http://www.tomtom.com/plus/service.php?ID=17
installed home software
then went to this site and followed its instructions
http://www.tomtom.com/support/index.php?FID=6736&Lid=1
and installed tomtom home plus on my computer
tomtom home is excellent for anyone that does not have it, its free and a must have.
tomtom home then updated all my software and gave me free some cool new stuff.
after this did as you said went outside three minutes it was up
thanks i hope this helps others
now if i can only try to see if i can modify my 838 to do this aswell
i know the 838's don't have gps connected inside unit but has anyone opened one up and connected it.
I currently have 4 brand new dopod 810s and 4 dopod 838's i will have to sell some as we just got given them and some people oready had them before we got given them.
they were given to you? wow! give them away too. throw one my way
Changing GPS
Can you change the GPS type once you have already installed it and it is running?
Speedn said:
tomtom works on my aussie D810 with the same rom...
I set the GPS reciever to other NMEA GPS reciever.
coldstart it can take a minute or more to find the signal.
try standing outside in a area with a good wide view of the sky, or even driving round.
Speedn
Click to expand...
Click to collapse
Are any of you guys with optus? I really want to wait for the official GPS rom from dopod but i dunno what these guys are doing, there has been all these claims of new roms coming out but no substance.
Which rom updates are you using? Any problems with the aussie networks?
Viperx,
Im using this rom. its the offical rom, but it hasnt been released on the dopod asia site for autralian customers as yet. I think I downloaded it from this forum ftp, cant recall now. works great with 3 so far, haven found any bugs. The only thing I fixed since the update was the bass (again that was found on this forum).
RUU_Trinity_DOPODASIA_WWE_1.23.707.6_6275_1.35.00.11_108_Ship.exe
SpeedN
i'm with optus
and i'm using the
RUU_Trinity_DOPODASIA_WWE_1.23.707.6_6275_1.35.00. 11_108_Ship.exe
ROM and it has been working fine
Where did you find the fix for the bass?
brandonmm said:
Where did you find the fix for the bass?
Click to expand...
Click to collapse
FOUND IT!!!
bass fix
http://forum.xda-developers.com/showthread.php?t=296912
keywords: bass fix trinity
enjoy
Speedn
lol too slow
TeamSpeedy said:
i'm with optus
and i'm using the
RUU_Trinity_DOPODASIA_WWE_1.23.707.6_6275_1.35.00. 11_108_Ship.exe
ROM and it has been working fine
Click to expand...
Click to collapse
Yep i downloaded this already. i heard from some people that utms has really bad reception with this rom? also this is wm5 isn't it.
Also is this a straight install or does it need sspl/hard spl or things i don't understand?
hi everyone here, i got D810 with 3G, i just wondering any1 had it work with 3G, can some1 tell me how to update to a GPS ROMs, coz i hv not idea how to flash the device,
i had been reading alot of the posts but still dunno wat to do, wat is SSPL and how to backup the ROM, can i flash bak to orignal one if it doesnt work. sorry to ask so many question at once, some1 plz help.
Hi
Hi,
I set GPs Program port COM9, hardware port COM 0.
I selected other NMEA GPS receiver and other bluetooth GPS receiver and selected GPS Device on COM9, but it says NO GPS device. What should I do. I'm really frustrated. any help will be appreciated.
cheers
Maulik.
Hi, i work everyday yesterday and today trying to make the destinator 6 work,
I use the duttýs feb.08 rom and radio i also try a lot, i am using now, the 1.58.21.23 NIKI
The problem is i can found the Gps port with destination configurations on COM4, 115200 , NMEA but WHEN I PUT IN THE SCREEN TO FIND THE GPS POSITIONS, I READ A MESSAGE " GPS ANTENNA NOT FOUND"
I only make it work emulating the gps position with FRASON GPSGATE .
I think the problem is the time or delay of antennas, what ca i do?
NOTE: AFTER A DESINSTALL THE FRASON GPS GATE I DO A HARD RESET.
tHANKS
FLAVIO MARTINS
SAO PAULO-SP
BRAZIL
any news?
Anyone have any news?
Flavio,
I installed destinator 6.1 and I'm having the same problem. It finds the GPs and keep changing from " GPS Antenna found" and "GPS Antenna not found" in each 2 seconds.
Is it the same problem that you are having?
I'm using Confused Stu's Windows Vista 1.3 Cooked Rom with Radio Ver 1.65.14.06 and Destinator 6 works perfectly
C
I'm using Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700
Destinator 7 work fine (downloaded a trial version) but id doesn`t have the language that I need, so I rather use Destinator 6.
Tried several versions of this ROM (Cube, no Cube and lite) and in everyone the same thing happens: It keep changing from "GPS Antenna found" "GPS Antenna nof found" every 3 seconds.
I think I gonna try one WM6.0 ROM to see if it works. I'll try Sleuth 1.2 first, than Confused Stu's Windows Vista 1.3 Cooked Rom.
Thanks
Try 6.0 NOT 6.1
Hi everyone,
This is my first post here and I would like to share my experience with the WM6.1 update and Destinator. I had been using an Asus n30 and for that to work I had to install Destinator 6.1.1 otherwise it would loose GPS etc. When I tried the same 6.1.1 update on my Kaiser (Vodafone version) with WM6.0 it worked basically but when I drove at higher speeds above 140-160 km/h (here in Germany this is quite a normal speed on the highway) the display would freeze and stop updating and I would no longer get voice instructions from Destinator.
So I had the crazy idea to update to WM6.1 to fix this...Big mistake...at first
Well as you have also found out it made things worse and I got the "GPS Antenna not Connected" issue.
I was able to solve my problem after a lot of tinkering with different radios and two ROM images one from Vodafone UK (3.28) and the last ROM posted from Dutty - which I am using now great stuff! both are WM6.1. What helped solve the problem was to revert back to Destinator 6.0 i.e. the original version from the CD-Rom that I had bought. After deleting the 6.1.1 version and installing 6.0 everything was fine no more "GPS antenna not connected" and no more freezes even when driving at over 200 km/h (130 Mph).
My guess is that the 6.1.1 update was optimized for slower devices like my n30 but the measures taken in that update that made slower PDAs work with WM3 SE were counter productive under a more modern OS like WM6.x
Even though this took me 3 days and a lot of head scratching to figure out I am very happy I did go through this process. Now thanks to this great community I have learned to flash Hard SPLs, change my ROMs as I please and as a result I have a much more powerful Kaiser . All of this despite what the lady at the Vodafone hotline told e "you can not use an update from the UK...or from HTC" ha ha .
I hope this may help some of the other users who have destinator 6 trouble.
Cheers
htpcman
Kaiser Problems
i have an htc 8900 series(its called the ATT tilt in the States, i think its called the Kaiser everywhere else) and i'm having problems with WM6 and desitnator 6. i installed it as instructed and when i try to open the program it seems like it tries to open it, but nothing happens and i get taken back to the today screen. i've even uninstalled the program and sent all the installation files from my ASUS 696 via bluetooth to my phone's card, but that didn't work either. Dest 6 works perfectly on the ASUS.
On my phone, GPS settings are Program port Com4, GPS hardware port (none), baud rate 4800. And the phone will not let me change the baud rate or the hardward port. It doesnt' save my changes. ANy help is appreciated.
Thanks
Hello,
I am trying since yesterday to make my GPS working, with no success. Everytime, I got the following message:
Cannot find port com. I do not know what the problem might be. I tried all Ports (from COM 0 to COM 12, and all Baud rates). Tried 3 differents GPS applications. Memory Map tells me for Port 0 GPS communication timeout...
In addition, I tried to play with the External GPS. I tried with Manage GPS automatically on and off. Still the same..
I begin to think my GPS unit is defective...
Any ideas would be appreciate.
Thanks very much in advance,
Philippe
did you change settings in the gps control panel?
the default settings can be left alone. COM4. Baud rate should be automatically handled and unless you enabled AGPS any baud rate will do, if you enabled AGPS then I think you have to use 2400 as your Baud.
I just noticed the GPS harddware port in setting, system External GPS is not saved when you click ente.
Exemple I choose COM4, and Baud rate: 4800. I click OK. When I reclick exernal GPS, Hardware, I have got ''none for GPS hardware port. I do not know if it might be one of the reason why the GPS does not work.
Note: I just flashed the new rom: 1.35.401.3 WWE. Might it be a bug in this ROM (just question?)
Philippe
I can cofirm TomTom working with COM4 and baud 57600. Signal pickup can be time hungry, tho. Sometimes I get a fix in 20 seconds, sometimes it takes as much as 10 minutes.
no problem using mapking...
Hello,
And thanks everybody for your help. I just updated to the new Elite 1 ROM, and now it works like a charm....Very good...
I do not know if there is many francophones on this forum, but there is a new french forum about the Diamond:
http://htc-touch-diamond.forumactif.info/index.htm
Not very busy yet, but....
Cheers,
Philippe
Same problem... The tomtom 6 don't detect my integrated gps... if i chose the wired and put ports like say before, it don't work too.. Any way for detect integrated gps?
Here are exactly my setting:
Setting system External GPS:
GPS program port: COM 4
GPS hardware port: None
Baud rate: 4800
Manage GPS automatically is checked.
So open your GPS program, choose COM Port 4, and baud rate: 4800.
Should work. If not, flashthe new Elite ROM. It could help too.
Philippe
I can't flash the rom, it will make the warranty expire... And the mobile isn't mine, it's destined to be selled, i work on a gsm shop...
got exactly opposite problem - when I leave these default settings in "External GPS" CPL, the Diamond will suck my batterry within several hours, as if the GPS was still ON. have found out that if I disable all settings in this CPL, it stops sucking power (but then I can't use the GPS, obviously) - any clues or solutions?
I HAD to enable Windows Mobile manages automatic in External GPS in 'settings'. Check if it is enabled.
Disabling it made GPS never work.
Strange?
Yes, unless I restored all settings to their original values (Virtual port - COM4, HW port - None, Managed access - checked), I was not able to use the GPS. But these were exactly the settings I was having the battery drain issue with... I miss the GPS LED indication vastly...
I am have this problerm too...
Solution : make hard reset.. no more!
And all will be ok ... about GPS.
i have same proplem
i have same proplem when i updat to the new rom 1.93
I have a similar Problem.
I Updates my ROM to the new branded one from O2-Germany and since then my GPS is not working anymore. in GPSMapware I get device.exe errors and TomTom7 keeps searching and searching and so on...
The old O2 ROM has no GPS problems and every software got a loc in about 10 - 20 seconds.
But the most intresting point is that my brother has a Diamond too and no GPS problems at all.
I think I will get a new one from O2 before flashing it and loose my warrenty
Telus CDMA Diamond
I've got problem too. First Diamond I had no problem with GPS, something happened with the phone I had to exchange, and new one (phone) GPS wouldn't pickup Sat. I'm on Telus CDMA. Maybe they removed physically on the second batch of Diamonds.
My GPS doesn't work too well either. I can usually get a fix eventually when outside with a clear view of the sky but in the car it is hopeless. I use TT7 and the GPS status screen shows that the Diamond can see maybe half a dozen satellites or so but with very low signal strength. The bars stay grey for ages and then eventually three or four will turn blue and all the time the battery is draining like crazy. I also have a Holux GPSlim 256 and with that I get a fix much faster and the signal strength is much higher. I can also use it in the car with no problem.
I have to say I'm pretty disappointed with the GPS performance of the Diamond and from the number of posts in this forum from people with similar problems I would suggest that there is a design flaw or very poor quality control. I had an XDA Orbit 2 for a while and that was far superior.
Me too
my diamond have the same problem too.
it was working with the old rom's and the early new
but later with new rom's it is locked, I don't know why or how to fix it.
then I back to the last good one but still locked.
it seem's working fine, because the software is detect the gps device and also detect it on port 4 and baud speed, but without signal any more.
I used Garmin, Destenator, iGo, fanaeen, and gps test.
and I try to use all avaliable solutions
I used all diamond rom's here and used all radio version's even the hardspl I changed it too with no succeed.
any advice would be help!
thanks in advanced
Hi,
I own two diamonds and I also found problems with the GPS in both of them. Probably mine is not the same you are describing. What I get is the following:
Running TT7, the GPS works but TT7 map in the screen remains in grey color. Rarely it shows color for some seconds and l"oses signal" again. It navigates, but no messages on proximity of POIs work. Also, when driving, if TT7 is forced to recalculate (every time I do not follow the instructions), it forgets about the required destination. In the GPS configuration option within TT7 it does not show satellites, the bars are empty and the coordinates shown are grey... but showing values!
Finally, I found the reason. I use Bluefire VPN, a piece of software to connect securely to my company. The GPS and Bluefire cannot live together.
I have tried everything: TomTom 6, changing COM port (many combinations)for the GPS, A-GPS on and off... No way.
It worked perfectly in P3600. I tried many ROMS and pieces of software without problems but in the Diamond I haven't been able.
Perhaps the reason is some resident code of Bluefire. Don't know. In any case, if this is a case similar to any of you, my advice is the following:
Hard reset, install TT7 and maps and test the GPS. If it works, start installing software until it crashes.
In my case, the GPS is always dead after the soft reset required after the installation of Bluefire, and it works again after another soft reset once Bluefire is uninstalled.
Hope it helps and hope somebody can also help me solve this issue.
SOLVED
Hi guys
Here is my solution.
First you have to flash 1.13.25.24 radio rom sometimes it can be solve the problem.If not you must open your phone with Htc service manual and find gps coaxial cable and check it.Sometimes it can be pulled out.Mine antenna was unconnected and gps couldnot find any satellites.Sorry for my bad english.
Hi all, yesterday i've changed the "external gps settings":
COM8 For virtual GPS port and COM 4 as Hardware GPS port, baud 9600.
Today i was using my GPS the first time after the settings descripted before...
The GPS Works, but at regular intervals of 2 sec, then stops for 10 sec (No GPS Found with Tomtom) and works again.....
Now i have 3 questions:
1) Can i solve this WITHOUT an Hard Reset??
2) If i disable the Virtual com port, tomtom DON'T let me choose another COMport (it skips the Comport configuration page) and, when it allows me to select the right port, the COM4 isn't there
3) There are A LOT of comport into "External GPS Settings", some starting with COM..X and others ports named GPD..X ..... What type of ports are??
(Ps: i have already installed tomtom again)
Did you try to disable AGPS?
I have only seen this problem when AGPS is enabled (via advanced config) too
Also the defualt GPS COM ports is 4 and baud rate of 4800 (should be no need to change this) and why mess with external GPS settings when the device has internal GPS?
I have same problem on iGO8 with AGPS enabled.
You guys are right! The A-GPS was ON (strange, i don't remember i've activated it)
If i play with the external gps app is because i would to share the same com port to 2 gps apps.....
BTW when i set the com4 in Hardware port, reopening the app it disappear.
Now i have Agps disabled, External gps app "void" and tomtom don't let me choose the comport (it switch from baud speed to mainscreen)
Hmm, I had no problem at all using GPS at standard settings for:
Igo
TrackMe
GoogleMaps
at the same time!
Riel said:
Hmm, I had no problem at all using GPS at standard settings for:
Igo
TrackMe
GoogleMaps
at the same time!
Click to expand...
Click to collapse
diamond has disabled agps out of the box.
Hmmm I had no problems the first couple of times I tried iGo when I first got the device. Then I tweaked it, enabled AGPS and all hell broke loose (presumably due to this setting, though not 100% sure since I changed lots of things). Disabled it on my own, trying to back-track, now it's better but I still got problems with GPS lost...
By the way, is there any use setting COM4 to high speeds? Does it reall improve performance?
I had the same problem after flashing the actual rom build from HTC club. I am currently sticking to this one in italian and no problem at all.
P.S.: Just noticed you're from my same city
All ok now, i suppose that if we leave blank the GPS port (no HW port) into first COM screen of external gps app, tomtom skip the comport settings screen, and don't allow you to choose another one.
I've Hardresetted my pda yesterday, and i've seen that out of the box, the diamond has COM4 selected by default.
I don't want to change anything now (i have no time in those days to do another Hard reset) BUT, if you have problems regarding the GPS COM Settings screen in tomtom, try to set the COM4 into GPS PORT (not hardware port) of the "External Gps" app.
hello everyone
i have the same problem of signal GPS lost and coming back after a few minutes of use (i use IGO 8), then lose again, then back again, and so on.
I installed the new flash rom from HTC eclub, (QMR-RUU_Diamond_HTC_FRA_1.93.406.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe)
Even if i disable the a-gps using advance config, the problem is still there.
Do you think that problem comes from that new HTC ROM ?
Any solutions?
NO... I had the same problem on old ROM very rarely and solved with Quick GPS , I will see if the problem persist on new ROM...
I had this disconnecting problem too with Tomtom 7,
now with Bepe 0.98 and radio Radio v1.00.25.07, all is OK, no disconnect at all this morning ( 2 hours of GPS use ).
But I don't know what resolve the problem, Bepe's ROM or the new .07 radio
my diamond refuse to accept setting for hardware port and rate......
it always displayed the default (hardware none ,,port 4800)
and always intermittent gps signal...
can u help me?
hmh79 said:
my diamond refuse to accept setting for hardware port and rate......
it always displayed the default (hardware none ,,port 4800)
and always intermittent gps signal...
can u help me?
Click to expand...
Click to collapse
Never mind the setting. Is AGPS disabled?
yes its disabled...
A bit strange, mine works perfectly with iGo, it even updates the position (almost) continuously when in pedestrian mode.
Perhaps you could try an auto detect from your GPS program to reset the link. By the way, what soft are you using?
well im using garmin xt and navigon...garmin display that the program and hardware is com:4
thank u for being patient with me....
I know Garmin works on the Diamond, so I'm running out of ideas... I remember reading that some VOIP programs screw the GPS. Did you install any such program?
If not, what I would do is back up my contacts and calendar and do a hard reset to see if this solves the problem. A bit painful, but will certainly answer the question whether there is something wrong with your hardware or not.
well.. i have changed the rom to karmba version, and it works fine for the last 6 hours..
gps functioning well.
may be the fault was in my previous rom (SwiftBL-WWE-Diamond-ROM-v5-5-Lite)
thank you very much for your help
Hello to all you guys are my last hope or I will just sell my tytn even if i don't want to.
My only problem is with the gps it simply dosent connects, and yes I have red several threads on it here still I have no solution. On the hardware tab in External gps settings I cant change either the port either the bud rate. I have pre-installed iGO 8, google maps, turbo gps and the geocashing software but none of them work.
SO please pretty pretty please if someone can give me a real answer how to fix it- do so. I really do not want to sell my phone (if i even can with not working gps)
P.S. I am using the latest shifu ROM
Isn't GPS junk with 6.5?
I finally got it!?!
The right settings for the tytn gps are
Hardware port com4
Bud rate 57600 (some software works with smller but this is the best)
You can not change it trough the WM it is fixed, you shud change the settings in the software you are using IGo, TomTom etc...