Hi I have a dopod D810 i would like to know how you get the gps working on this model, can someone please help me
I did upgrade rom to 1.23.707.6 and install a TomTom program but it still looks for gps device
does the D810 have a device built in
has anyone done this Thanks
cheers
tomtom works on my aussie D810 with the same rom...
I set the GPS reciever to other NMEA GPS reciever.
coldstart it can take a minute or more to find the signal.
try standing outside in a area with a good wide view of the sky, or even driving round.
Speedn
Depending on the version of/locked files (Search forum) TOMTOM, you might need to configure it each time.
In 6.02 and below you need to select the NEMA (or whatever its called).
In 6.03 they have a selection of inbuilt GPS device. I Found 6.03 much less hassle to be honest.
how do i get 6.03 please
how do i get 6.03 please
to get tomtom 6.03 update go to the following site and follow their instructions...
http://www.tomtom.com/support/solution.php?GID=3&PID=1401&SID=0&CID=215&Language=1&FID=6736
NOTE: you will need reactivation of your maps after this upgrade to 6.03
please if anyone can help
i have a d810 have installed
rom 1.23.707.6
radio version 1.35.00.11
protocol 32.68.7020.10h
installed tomtom6
selected nmea gps
it asks baud rate
i left it at 4800
it then comes up with
com3:
gps in com9
com7:
ril on com6:
s2410 IRDA
usb Cable:
??????????? i have no idea which to pick i selected com3:
for instance and it says no gps device
i select gps in com9
it says waiting for vaild signal but never finds anything
srsjason2040 said:
i have a d810 have installed
rom 1.23.707.6
radio version 1.35.00.11
protocol 32.68.7020.10h
installed tomtom6
selected nmea gps
it asks baud rate
i left it at 4800
it then comes up with
com3:
gps in com9
com7:
ril on com6:
s2410 IRDA
usb Cable:
??????????? i have no idea which to pick i selected com3:
for instance and it says no gps device
i select gps in com9
it says waiting for vaild signal but never finds anything
Click to expand...
Click to collapse
Are you outside with clear view to the sky? Wait 15 Minutes there! It WILL work.
You're on the right track with GPS on COM9 if you are not using version 6.03. If you get as far as "No valid GPS signal" message then that means your GPS receiver is tracking satellites ok and you're just not getting a GPS fix. I had the exact same problem as you.
1) Just restart your d810 (stylus into the small hole on the underside of your dopod )
2) Start your TomTom and use the same setup as you did before with NMEA.
3) Select GPS on COM9
4) When you get the "No valid GPS signal" message stand outside where there is lots of open sky (if you're in the city... tough luck it would be really hard to get a GPS fix there).
5) Be prepared to wait for up to 15 minutes until you get a GPS fix. Mine took more than 10 minutes.
Got it working plus more
Thanks guys you have been a great help
i updated my tomtom software it was easy
as advised i went to here
http://www.tomtom.com/plus/service.php?ID=17
installed home software
then went to this site and followed its instructions
http://www.tomtom.com/support/index.php?FID=6736&Lid=1
and installed tomtom home plus on my computer
tomtom home is excellent for anyone that does not have it, its free and a must have.
tomtom home then updated all my software and gave me free some cool new stuff.
after this did as you said went outside three minutes it was up
thanks i hope this helps others
now if i can only try to see if i can modify my 838 to do this aswell
i know the 838's don't have gps connected inside unit but has anyone opened one up and connected it.
I currently have 4 brand new dopod 810s and 4 dopod 838's i will have to sell some as we just got given them and some people oready had them before we got given them.
they were given to you? wow! give them away too. throw one my way
Changing GPS
Can you change the GPS type once you have already installed it and it is running?
Speedn said:
tomtom works on my aussie D810 with the same rom...
I set the GPS reciever to other NMEA GPS reciever.
coldstart it can take a minute or more to find the signal.
try standing outside in a area with a good wide view of the sky, or even driving round.
Speedn
Click to expand...
Click to collapse
Are any of you guys with optus? I really want to wait for the official GPS rom from dopod but i dunno what these guys are doing, there has been all these claims of new roms coming out but no substance.
Which rom updates are you using? Any problems with the aussie networks?
Viperx,
Im using this rom. its the offical rom, but it hasnt been released on the dopod asia site for autralian customers as yet. I think I downloaded it from this forum ftp, cant recall now. works great with 3 so far, haven found any bugs. The only thing I fixed since the update was the bass (again that was found on this forum).
RUU_Trinity_DOPODASIA_WWE_1.23.707.6_6275_1.35.00.11_108_Ship.exe
SpeedN
i'm with optus
and i'm using the
RUU_Trinity_DOPODASIA_WWE_1.23.707.6_6275_1.35.00. 11_108_Ship.exe
ROM and it has been working fine
Where did you find the fix for the bass?
brandonmm said:
Where did you find the fix for the bass?
Click to expand...
Click to collapse
FOUND IT!!!
bass fix
http://forum.xda-developers.com/showthread.php?t=296912
keywords: bass fix trinity
enjoy
Speedn
lol too slow
TeamSpeedy said:
i'm with optus
and i'm using the
RUU_Trinity_DOPODASIA_WWE_1.23.707.6_6275_1.35.00. 11_108_Ship.exe
ROM and it has been working fine
Click to expand...
Click to collapse
Yep i downloaded this already. i heard from some people that utms has really bad reception with this rom? also this is wm5 isn't it.
Also is this a straight install or does it need sspl/hard spl or things i don't understand?
hi everyone here, i got D810 with 3G, i just wondering any1 had it work with 3G, can some1 tell me how to update to a GPS ROMs, coz i hv not idea how to flash the device,
i had been reading alot of the posts but still dunno wat to do, wat is SSPL and how to backup the ROM, can i flash bak to orignal one if it doesnt work. sorry to ask so many question at once, some1 plz help.
Hi
Hi,
I set GPs Program port COM9, hardware port COM 0.
I selected other NMEA GPS receiver and other bluetooth GPS receiver and selected GPS Device on COM9, but it says NO GPS device. What should I do. I'm really frustrated. any help will be appreciated.
cheers
Maulik.
Related
Hi All,
Could someone please let me know how to use the GPS in my phone. I have tried upgrading the phone to different ROMS that were supposed to enable the GPS and now I am currently using the official HTC WM6 Australia but I cannot get the GPS detected in TomTom or Google Maps. Any help on this would be very, very appreciated since one of the reasons because I bought the phone was because of the GPS...
Thanks in advance
what settings are you using for your TomTom?
Does it say "No GPS Device"?
If it says "Waiting for a valid GPS signal", then you just gotta walk outdoor and wait a few mins...
Note that it takes quite awhile for the first lock.
please state your radio version as well
GPS Problems
Hi,
Windows Mobile 6 Professional (Build 17944.0.3.1)
ROM. 3.00.707.17
ROM Date 06/29/07
Radio Version. 1.38.00.11
I use the "Other NMEA GPS receiver" /115200 GPS baud rate /GPS in COM9
and it says "waiting for a valid GPS signal..." but I have been outside the house waiting for 20 minutes and it doesn't pick up the signal. My TomTom bluetooth GPS used to pick up the signal in 1 minute.
If I get this GPS running, how long will I have to wait everytime I want to use my GPS?
Thanks
Alonso
sounds like a tom tom configuration issue.. .there are threads for this in the forum, cause your radio and rom are up to date.. (although i'd suggest a newer radio to get rid of battery drain). It definitely shouldn't take 20 minutes.. i think within 4 minutes it should be set, most of the time MUCH quicker (2min?)
Where can I get the radios
Sure, where can I get the radios updates?
Are all compatible with all the different ROM versions?
I had similar issue with Tomtom recently. After I have TomTOM software downdgraded back to version 6.010 instead of 6.030 problem is gone.
i9796674 said:
Hi,
Windows Mobile 6 Professional (Build 17944.0.3.1)
ROM. 3.00.707.17
ROM Date 06/29/07
Radio Version. 1.38.00.11
I use the "Other NMEA GPS receiver" /115200 GPS baud rate /GPS in COM9
and it says "waiting for a valid GPS signal..." but I have been outside the house waiting for 20 minutes and it doesn't pick up the signal. My TomTom bluetooth GPS used to pick up the signal in 1 minute.
If I get this GPS running, how long will I have to wait everytime I want to use my GPS?
Thanks
Alonso
Click to expand...
Click to collapse
First of all, your GPS device IS detected. There is too steps when Tomtom is trying to make a GPS fix: 1) no GPS device 2) waiting for a valid signal. If you've already reached the second one it means Tomtom can sense your GPS but it cannot aquire the three satelits signal required for a valid location fix.
I would suggest you upgrade your radio. Athough the 1.38 one can work, I didn't have a good GPS with it and it tookme ages for a fix, and sometimes no fix possible.
Besides, that radio wasn't made for the newest wm6 roms.
1.46 will work way better for that.
And since Tomtom is not the lightest application for GPS testing, I would suggest you try other apps such as GPS test (which is free etc.) you'll get a fix quicker, and once you had a fix, all other applications will fix instantly too.
You can try the GPS function in the camera too, which is quite light too and fix quicker than Tomtom.
Hi guys!
Im freaking out! I have a Dutch MDA Vario3 and I just cant seem to get the GPS to work. Tomtom can find the intern gps but no signal! I waited for about an hour today and yesterday it didnt work also..somebody can help me out? I use tomtom 6.032
help me out will yah...
try using the gps test first or quickgps before tomtom.
kidd78 said:
try using the gps test first or quickgps before tomtom.
Click to expand...
Click to collapse
I did quickgps for about ten times!
gps test?
thx for your reply
Were you indoors? Did you move to a different location? You might want to test it with an external gps receiver or try a standalone gps unit (if you can borrow one). Try and find something that is more sensitive than the Kaiser, and, in the same location, see if you can get a signal.
My point is, you might just be in a bad spot. This happens to me at work all the time, it never picks up a signal, even after an hour of searching.
you must set the right com ports up
find out which port gps is on ie. usually com7
go into config (tomtom) annd then guide the tomtom to com7
it will work took me a couple of days to work it out then seemed so obvious
The above advice is all pretty good. If this is the first time you have used tomtom then it can take a good while.
I am assuming tomtom shows the message "no valid GPS signal" after showing briefly the message "No GPS device". If so this is good. It means your com ports are set correctly.
There are two things to be sure of though:
1.
You have aclear view of the sky - especially on the first occassion you get a fix.
2.
Make sure you have a suitable map in the correct location. Obviously getting a fix when there is no map or the map is in the wrong directory will not succeed.
Did quick GPS work and give you a "valid until" date?
GPS test is a nice simple app that will show you the port number you are on so you can make sure tomtom is using the same one. BUT if tomtom only fails at the no valid signal stage then I think your ports are fine.
Finally, some fatal problems can occur if you have changed entries in the "external GPS" settings. This might (according to some folk) require a hard reset to correct. But try the above first.
Mike
Check this thread first..
http://forum.xda-developers.com/showthread.php?t=330412
Try GPSViewer and select the port settings manually and choose "Open GPS".
You should see some som action through GPS strings in the Setup page.
Then try with TomTom or Google Maps.
I never had issues with TomTom, but google map was having hard time initializing. But after using GPSViewer, it works pretty neat and quick!
arunprakashr said:
Check this thread first..
http://forum.xda-developers.com/showthread.php?t=330412
Try GPSViewer and select the port settings manually and choose "Open GPS".
You should see some som action through GPS strings in the Setup page.
Then try with TomTom or Google Maps.
I never had issues with TomTom, but google map was having hard time initializing. But after using GPSViewer, it works pretty neat and quick!
Click to expand...
Click to collapse
It tests all com-ports,but gpsviewer cant find anything..
While it is true that you can screw yourself if you mess with the external GPS settings, you might not have to hard reset. Check the Kaiser Wiki; all the way at the bottom, you'll find links to the registry settings for the internal GPS. If you follow those steps, and set your TomTom to Other NMEA Receiver, you'll be fine no matter what you did with the external settings.
mikechannon said:
The above advice is all pretty good. If this is the first time you have used tomtom then it can take a good while.
I am assuming tomtom shows the message "no valid GPS signal" after showing briefly the message "No GPS device". If so this is good. It means your com ports are set correctly.
There are two things to be sure of though:
1.
You have aclear view of the sky - especially on the first occassion you get a fix.
2.
Make sure you have a suitable map in the correct location. Obviously getting a fix when there is no map or the map is in the wrong directory will not succeed.
Did quick GPS work and give you a "valid until" date?
GPS test is a nice simple app that will show you the port number you are on so you can make sure tomtom is using the same one. BUT if tomtom only fails at the no valid signal stage then I think your ports are fine.
Finally, some fatal problems can occur if you have changed entries in the "external GPS" settings. This might (according to some folk) require a hard reset to correct. But try the above first.
Mike
Click to expand...
Click to collapse
I have the phone since yesterday! All settings are ok! I first had t-mobile ROM on my phone, flashed it over with a dumpped original dutch htc rom. (gps also didnt work at the original rom that was on it from t-mobile)
I live in de centre of the city. No clouds or anything..
Where can I find gps test? I tried GPS Viewer, didnt work at all, cant seem to find any ports. I did hard reset and still..it doesnt work..
Bram87 said:
I have the phone since yesterday! All settings are ok! I first had t-mobile ROM on my phone, flashed it over with a dumpped original dutch htc rom. (gps also didnt work at the original rom that was on it from t-mobile)
I live in de centre of the city. No clouds or anything..
Where can I find gps test? I tried GPS Viewer, didnt work at all, cant seem to find any ports. I did hard reset and still..it doesnt work..
Click to expand...
Click to collapse
GPS test here:
http://classic.pocketgear.com/software_detail.asp?id=24687&associateid=1224
It would help us to know the following:
1.
When tomtom is on does the amber led for GPS flash?
2
Does tomtom show "no valid GPS signal"?
3
Have you got a local map installed?
4
Did quick GPS download current data?
Mike
1.
When tomtom is on does the amber led for GPS flash?
Jep
2
Does tomtom show "no valid GPS signal"?
also correct
3
Have you got a local map installed?
uuh..west europe map..
4
Did quick GPS download current data?
it says after download "valid for six days and twentythree hours"
So I gues, yes
*thx Mike for helping me so far
Edit* gps test; shows "GPS is starting up"..(slow..)
Mmmm. Did GPS test show any bars in the end?
Mike
mikechannon said:
Mmmm. Did GPS test show any bars in the end?
Mike
Click to expand...
Click to collapse
Hi mike..
It works..It took some time (alot) but..It works..Hope it keeps working!
Thank you and wish you a happy new year!
Bram87 said:
Hi mike..
It works..It took some time (alot) but..It works..Hope it keeps working!
Thank you and wish you a happy new year!
Click to expand...
Click to collapse
Yep, first time around it can take a loooong time. After that it should be faster.
Happy New Year.
Mike
Over the last few days I have noticed that my GPS is not really working anymore. I'm not sure if this is a result of some software I've loaded or whatever, but I've noticed a few people saying that they are no longer locking onto satellites and noone is really sure what they've done - although there is a thread about the new Clove extended battery and many have mentioned that it stops the GPS from working.
I'd like to get everyone who is having problems to post here please so we can try and work out what the cause is. Some have speculated that it could be the radio but I don't think it is, I've flashed every single radio available with no change...
When I first got my diamond, I was IMPRESSED at the speed and accuracy of the GPS. I would get locks in around 10-15 seconds and using TomTom 7 I found it to be extremely accurate with regards to my position on the map.
Now it SUCKS. The other day I drove and it took 18 minutes to get a fix. When it finally did I estimate it was between 50m - 100m inaccurate. Some kind of lag is going on.
As of the last two days, I cant even seem to track ANY satellites. Since then, like I mentioned I have tried every radio and still the situation remains bad.
- I'm running a cooked ROM based on the 1.93.xx.x. (Elite 3.0)
- Current radio is .11 which seems to work well for my push email. (.05 worked well too) Other than that over the last couple of days its just been push email, a few texts and calls and really nothing else special I'm doing with the device.
Can anyone having the same problems please post here with your ROM version and let us know what your experiences are.
Thanks.
I have the same problem
Rom 1.93 - swift.
radio .05
I recently bought 'htc diamond'.
I have a doubt. GPS service is for 'FREE' or we have to pay?
My phone says 'GPS download valid: 4 days. It means i can download GPS for free until another 4 days? kIndly let me know I am a newbie.
thank you in advance
Sony
sonyuk143 said:
I recently bought 'htc diamond'.
I have a doubt. GPS service is for 'FREE' or we have to pay?
My phone says 'GPS download valid: 4 days. It means i can download GPS for free until another 4 days? kIndly let me know I am a newbie.
thank you in advance
Sony
Click to expand...
Click to collapse
No.. Its just the GPS data thats used by the gps to get a quicker lock on the satelites.. Which then only saves you time.. It does not cost you anything besides the trafik it uses to update the data..
sonyuk143 said:
I recently bought 'htc diamond'.
I have a doubt. GPS service is for 'FREE' or we have to pay?
My phone says 'GPS download valid: 4 days. It means i can download GPS for free until another 4 days? kIndly let me know I am a newbie.
thank you in advance
Sony
Click to expand...
Click to collapse
gps is for free, the "4 days" corresponds to the time which your device
has the almanach data for faster satellite lock in it's memory. after this time
quickgps will download the alamanach data for the next 7 days, and so on...
if you don't use this feature you still can use gps, but obtaining a fix will
take you a longer time!
regards,
markus
Please look at my post at
http://forum.xda-developers.com/showthread.php?t=408560
I have noticed that it is also dependent on the Rom. I am into flashing different roms and have seen different behaviour of Gps with each rom.
But HARD reset is a must after each flash.
Let me know your findings.
Got my GPS working in TomTom..
Steps i took:
1: change in PPC the gps port to COM6 - So still at Baud 4800
2: TomTom - Gps configure - "Other NMEA GPS reciver" - Baud 4800 - "COM6"
3: Closed TomTom
4: changed in PPC the GPS port back to "COM4" - still baud 4800
5: TomTom - Gps configure - "Build in gps"
And done.
I have this problem- the GPS seems to get worse and worse after a hard reset or rom upgrade to the point where it won't lock on at all.
I have noticed that in TT7 a number of satellites are being found (in the gps menu)but they are greyed out. Despite this it just won't lock on however long i leave it.
I notized that I was sometimes unable to track any satellites because I swiched on "A-GPS" in the registry with some kind of editor. After switching it off the problem was gone.
Greetz
Yes, Advanced Config destroy your GPS if you use it to turn on A-GPS.
Try reflashing the Radio with the same build as you are using already. It resets the GPS and did the trick for me.
How can you turn on A-GPS in the registry? Which key is it?
I have the same problems: when I use the GPS, it finds some satellites and not, and back it finds them, and not. When I use tomtom 6, the screen turns grey and colored every 5 sec., because it finds the satellites and not.
Sometimes it works good, but mostly not.
Can somebody help!!!
ROM: 1.35.404.4 NLD
Rom date: 05/30/08
Radio: 0.93.25.NS26
Protocolversion: 52.26.25.09H
jonnytheponny said:
How can you turn on A-GPS in the registry? Which key is it?
I have the same problems: when I use the GPS, it finds some satellites and not, and back it finds them, and not. When I use tomtom 6, the screen turns grey and colored every 5 sec., because it finds the satellites and not.
Sometimes it works good, but mostly not.
Can somebody help!!!
ROM: 1.35.404.4 NLD
Rom date: 05/30/08
Radio: 0.93.25.NS26
Protocolversion: 52.26.25.09H
Click to expand...
Click to collapse
There is a little tool which is called "HTC GPS TOOL(S)", dont remember the exact name.. there you can search for satelites using the "cold start" option.. when some satelites are found, then push the "Nav. Init." buttion", dont close the program, just start TomTom and se if it did lock? .. Some reported this method working..
ostendk said:
Got my GPS working in TomTom..
Steps i took:
1: change in PPC the gps port to COM6 - So still at Baud 4800
2: TomTom - Gps configure - "Other NMEA GPS reciver" - Baud 4800 - "COM6"
3: Closed TomTom
4: changed in PPC the GPS port back to "COM4" - still baud 4800
5: TomTom - Gps configure - "Build in gps"
And done.
Click to expand...
Click to collapse
I did things a little differently to yourself, but certainly your general method has solved the problem!
Firstly, and I don't know if this is a result of the radio version I'm running but I only have COM4 and COM7. Running radio .11
Secondly, within TomTom I simply configured the GPS, I changed to other NMEA receiver, selected COM4, and Baud 4800, and then within about 10 seconds, I had a lock. This is after days of not getting a lock at all.
Restarted TomTom, switched back to 'Internal GPS Receiver' and almost instantly locked again.
Problem solved!
I had done many ROM updates and not noticed this effect, I believe now thinking back this must have been a direct result of updating the radio only from version .03 to .05
I will update the thread title.
salada2k said:
I did things a little differently to yourself, but certainly your general method has solved the problem!
Firstly, and I don't know if this is a result of the radio version I'm running but I only have COM4 and COM7. Running radio .11
Secondly, within TomTom I simply configured the GPS, I changed to other NMEA receiver, selected COM4, and Baud 4800, and then within about 10 seconds, I had a lock. This is after days of not getting a lock at all.
Restarted TomTom, switched back to 'Internal GPS Receiver' and almost instantly locked again.
Problem solved!
I had done many ROM updates and not noticed this effect, I believe now thinking back this must have been a direct result of updating the radio only from version .03 to .05
I will update the thread title.
Click to expand...
Click to collapse
I did actually update to the .05 radio, which after i had the satelite lock problem.. but haven't had i since i did that little com-port exchange
Hi,
After an hard reset un my Diamond and after instalall the .net framwork 3.5 my gps dont work anymore. When i turn it on connects the gprs and stay lots of minutes finding the sattelites.
Before the hard reste i have the tomtom working perfectely and never my htc connects the gprs for noting.
Can anyone help me please.
Regards,
Hallo All Gurus,
I'm trying out Garmin Mobile XT for WindowsMobile V4.20.50w with my TyTnII using Malsing's map (named as gmapsupp). I followed all recommended installation procedures installed Garmin XT and mailsing map in SD card \Garmin. But when I execute Garmin XT, I couldn't get it work and I noticed:-
a) when I'm at "GPS Info", it keep showing me "Acquiring Satellities"
b) In view map mode" keep showing "Searching for Satellites"
c) When I keyed in a address and hit GO or "Where Am I", it keep showing "Awaiting Better GPS Accuracy"...
I also noticed my GPS signal level only show 1 small bar and "GPS info" mode showed me only 1-2 satellite icon on the circle.. I never able to get 5 bars..
Tried many days and still can't get it works...
Before I use Garmin, my MapKing works fine...
Any guru can show me anything I missed out...?
Thanks in advance...
PS: I based in Singapore
ahchek said:
Hallo All Gurus,
I'm trying out Garmin Mobile XT for WindowsMobile V4.20.50w with my TyTnII using Malsing's map (named as gmapsupp). I followed all recommended installation procedures installed Garmin XT and mailsing map in SD card \Garmin. But when I execute Garmin XT, I couldn't get it work and I noticed:-
a) when I'm at "GPS Info", it keep showing me "Acquiring Satellities"
b) In view map mode" keep showing "Searching for Satellites"
c) When I keyed in a address and hit GO or "Where Am I", it keep showing "Awaiting Better GPS Accuracy"...
I also noticed my GPS signal level only show 1 small bar and "GPS info" mode showed me only 1-2 satellite icon on the circle.. I never able to get 5 bars..
Tried many days and still can't get it works...
Before I use Garmin, my MapKing works fine...
Any guru can show me anything I missed out...?
Thanks in advance...
PS: I based in Singapore
Click to expand...
Click to collapse
Garmin MXT only works with Garmin GPS receiver i.e. Garmin 10X .. or u can purchase the Garmin microSD and your internal GPS can be used..
p/s: unl
Good luck
pcboyy said:
Garmin MXT only works with Garmin GPS receiver i.e. Garmin 10X .. or u can purchase the Garmin microSD and your internal GPS can be used..
p/s: unl
Good luck
Click to expand...
Click to collapse
ERM i have mobile xt running on my kaiser fine without a stand alone without a garmin 10x. from what i have heard he just isnt waiting long enough to get a sat signal. in the start screen were view map and were to go are located there is a 5 bars in top left hand side and untill they are green nothing will work and if you go to gps info you need at least 5 sat's to get a lock but just wait longer as it runs fine on mine just takes like 3-8 mins to get a lock depending on weather and radio.
vj4 said:
ERM i have mobile xt running on my kaiser fine without a stand alone without a garmin 10x. from what i have heard he just isnt waiting long enough to get a sat signal. in the start screen were view map and were to go are located there is a 5 bars in top left hand side and untill they are green nothing will work and if you go to gps info you need at least 5 sat's to get a lock but just wait longer as it runs fine on mine just takes like 3-8 mins to get a lock depending on weather and radio.
Click to expand...
Click to collapse
yes, thats it, also u can run quickgps before launching garmin.
Thanks you guys for all advise.. True that I have difficulties in acquiring satellites due to bad weather, very thick cloud.. I managed to get through successfully once yesterday evening.. But, when I tried this morning, again it start "Awaiting for GPS accuracy"...
Need your further advice:-
a) When compare to my friend's HTC Diamond, he can obtain GPS much faster, almost within 1-2 mins.
Do I need to get Quick GPS activated every time I use garmin XT?
b) Why those Satellites that I searched all lost after I closed the garmin?
c) I just upgrade to WM6.1, is this one of the factor?
Appreciate any further kind advice please.
ahchek said:
Thanks you guys for all advise.. True that I have difficulties in acquiring satellites due to bad weather, very thick cloud.. I managed to get through successfully once yesterday evening.. But, when I tried this morning, again it start "Awaiting for GPS accuracy"...
Need your further advice:-
a) When compare to my friend's HTC Diamond, he can obtain GPS much faster, almost within 1-2 mins.
Do I need to get Quick GPS activated every time I use garmin XT?
b) Why those Satellites that I searched all lost after I closed the garmin?
c) I just upgrade to WM6.1, is this one of the factor?
Appreciate any further kind advice please.
Click to expand...
Click to collapse
I had the same issue after upgrading to WM6.1.
Then I upgraded to HardSPL 3.56 and Radio 1.70.x.x, L26 v12 ROM.. all is well now
dvn2008 said:
I had the same issue after upgrading to WM6.1.
Then I upgraded to HardSPL 3.56 and Radio 1.70.x.x, L26 v12 ROM.. all is well now
Click to expand...
Click to collapse
Hi dvn,
What is HardSPL 3.56 and Radio 1.70.x.x, L26 v12?? ROM updates? Where to find? Same installation as WM6.1?? Sorry I am not sure of all these ROM stuffs..
Appreciate your kind pointer please.
Thanks.
ahchek said:
Thanks you guys for all advise.. True that I have difficulties in acquiring satellites due to bad weather, very thick cloud.. I managed to get through successfully once yesterday evening.. But, when I tried this morning, again it start "Awaiting for GPS accuracy"...
Need your further advice:-
a) When compare to my friend's HTC Diamond, he can obtain GPS much faster, almost within 1-2 mins.
Do I need to get Quick GPS activated every time I use garmin XT?
b) Why those Satellites that I searched all lost after I closed the garmin?
c) I just upgrade to WM6.1, is this one of the factor?
Appreciate any further kind advice please.
Click to expand...
Click to collapse
As far as i know a different hard spl will not help i have used 3 differnt hard spl's and it has never affected me. a new radio will help this is were your problem will be! quick gps only needs to be run once a week make sure you dont have ur ip dummied to another country as this will make it useless. click download when connected to wifi or gprs/hsdpa if your lucky enough to be happy and afford to pay for your internet. it should get you a file that lasts for 6days 23 hours. wm6.1 has nothing to do with it. you will not get a fix inside your house flat shed etc you need to be out side or in a car (with phone on dashboard) so basicly the phone needs a clear view of sky. based on what you have said i would change my radio its all in the wiki I cannot recommend one to you as i am in the UK and different one's work better in different places. so try a few and see what works best. garmin forgets the satilites it connected to last time because you turned ur gps reciver of so it isnt connected to them and unless you restart garmin straight away the satalites are not in the same place in the sky so it has to relocate them(this is the same for every one)
ok mine is quite funny case.. if i use GMXT, the satellites will take looong time to be locked.. i tried GPSProxy (its a software) and run it 1st.. perghhh.. now it takes only 20sec to lock (with GPSProxy) and i continue to use my GMXT
pcboyy said:
ok mine is quite funny case.. if i use GMXT, the satellites will take looong time to be locked.. i tried GPSProxy (its a software) and run it 1st.. perghhh.. now it takes only 20sec to lock (with GPSProxy) and i continue to use my GMXT
Click to expand...
Click to collapse
Hi pcboyy,
Just only GPSproxy?? When I install it, it prompted me for some more files related to Net...
When I activated GPSproxy, I .. a lot of setting.. how to??? Appreciate your helps...
ahchek said:
Hi pcboyy,
Just only GPSproxy?? When I install it, it prompted me for some more files related to Net...
When I activated GPSproxy, I .. a lot of setting.. how to??? Appreciate your helps...
Click to expand...
Click to collapse
simple steps but hard to explain.. kindly refer here
http://www.malsingmaps.com/wiki/index.php/All_about_GPSProxy
pls try and let us know your result
Hi.to everybody in this forum.I have an HTC Diamond previously locked to Orange Uk now unlocked to all networks ....with your help.
But I face a great problem!!
GPS is not locating satellites at all!!!
Before you ask me if I have read through out the forum, YES I DID (A LOT).
I tried everything, HTC GPS tool , GPS TEST , hard resets ,soft resets ,mpla mpla .....everything...but no result.
CAN you help??PLSSSS
My Htc comes with the new ROm 1.93
you didn't get a fix from the beginning or was it already working once?
what app are u using?
the gps i configured correctly?
app sees the GPS module?
start in this way, then we can talk...
I had same problem ,after my provider update (the radio maybe) it solve the problem. check what is your radio version and tell us..
g-fall said:
you didn't get a fix from the beginning or was it already working once?
what app are u using?
the gps i configured correctly?
app sees the GPS module?
start in this way, then we can talk...
Click to expand...
Click to collapse
Never worked from beginning!
I use destinator 7,all settings are correct and the most strange of all is that application actually can see the GPS module in COM4!!
arix said:
I had same problem ,after my provider update (the radio maybe) it solve the problem. check what is your radio version and tell us..
Click to expand...
Click to collapse
ROM:1.93.405.1 WWE
RADIO:1.00.25.05
I hope i dont have to get involved into this since the phone was bought from ebay (UK) and I leave in Greece!!.Now phone is unlocked and I think I will not be able to contact Orange network for update.
I don't know what I had b4, but now mine is:
ROM:1.93.456.2 WWE
RADIO:1.00.25.05
Seems like your ROM version is kinda old,
Maybe one of the guru here can help you,
or update your ROM by yourself (your own risk)
com port 4, baud 57600, gps enables - this is what i use in iGO8 and works perfect
what is set in "setings->system->External GPS"? Here you can find some settings also
programs - com4
hardware - GPS HWport none , baude 4800
access - tick manage GPS automatically
g-fall said:
com port 4, baud 57600, gps enables - this is what i use in iGO8 and works perfect
what is set in "setings->system->External GPS"? Here you can find some settings also
programs - com4
hardware - GPS HWport none , baude 4800
access - tick manage GPS automatically
Click to expand...
Click to collapse
Those are the settings I have as well!!
I lost gps functionality after flashing to a new ROM.
Radio .07 and doing a "warm start" in htc gps tools got it working again, now from cold (ie initialising device to getting lock) is 25 seconds. (20 seconds to initialize gps, 5 seconds to get a lock!)
Try using gps gate,it will automatically configure gps settings and then start destinator,it should detect the inbuilt gps receiver and give you a fix,I had exactly the same problem with destinator 7, it just would not detect gps after using gps gate everythings fine,hope this helps.
arvind09 said:
Try using gps gate,it will automatically configure gps settings and then start destinator,it should detect the inbuilt gps receiver and give you a fix,I had exactly the same problem with destinator 7, it just would not detect gps after using gps gate everythings fine,hope this helps.
Click to expand...
Click to collapse
How do I use the gps gate? Where do I have to go at first place?
ok found it ..I will try this as well.
Please update your radio to .07. I had the problem of not getting a fix. The GPS Info showed many satellites but none would get a fix. I went for a radio update to .07 & now, even when the GPS signal is in RED I get navigation working.... perfectly. Touch wood
Skele said:
Please update your radio to .07. I had the problem of not getting a fix. The GPS Info showed many satellites but none would get a fix. I went for a radio update to .07 & now, even when the GPS signal is in RED I get navigation working.... perfectly. Touch wood
Click to expand...
Click to collapse
I am using GPSGATE now to try it out.I have already downloaded radio 07 and it will be my next move if gpsgate is no use
babis5570 said:
I am using GPSGATE now to try it out.I have already downloaded radio 07 and it will be my next move if gpsgate is no use
Click to expand...
Click to collapse
gpsgate did not work either!!!!
I am trying to update Radio to 07 with RUU but it just stays in 0%.
Any help plssss????
Changed the radio but still the same .It will not find any satellites.Maybe the gps chipset is %^$%$#.
ok, your GPS module is detcted, right?
In GPS test, can you see signal of satelites or not?
Flash your radio again and do intermediate hard reset before phone fully boots. If doesn't work flash both rom and radio (hard reset after each!). Just had the same problem on my diamond (solved today) and had it in the past on Kaiser. GPS detected, gps tool see sats but they are permanently red and flat (like they wouldn't have any strengh at all) And its always to do with radio so don't worry about your chipset.
I just read another thread and found this:
Both posts from LoardDark
**********************************************
POST394:
Hi,
After i had some GPS-Problems (no Sattelite link etc.) i tested many combinations on my own. At the End this works on two Diamonds:
1. Follow the "Unlock description" if necessary
2. Flash your ROM (i used the AZTOR V6)
3. Hard-Reset your Device! <- Important
4. check Com-Port
5. Cold Boot yor GPS
6. Warm Boot yor GPS
7. Hot Boot your GPS
8. No link-Problems, no Lags and very fast Sattelite link (after a few Tests: First Sattelite Link ca. 2 min. After first using GPS ca. 20 sec. to Sattelite-Link)
Important: After installing "Sensor-Lock" my GPS was completely Dead.
I don`t read the completely Thread but i hope this is a little bit helpful.
Greetings
Jerry
*********************************
POST 408
At first start GPS Tool -> QualcommChip "Yes" -> Cold Boot
then start GPS Tool -> QualcommChip "Yes" -> Warm Boot
at least start GPS Tool -> QualcommChip "Yes" -> type X -> Hot Boot
***********************************
here is the link for GPS tool
http://forum.xda-developers.com/showthread.php?t=360477
this is actually for improving the GPS lag but maybe helping for you...
good luck!
arvind09 said:
Try using gps gate,it will automatically configure gps settings and then start destinator,it should detect the inbuilt gps receiver and give you a fix,I had exactly the same problem with destinator 7, it just would not detect gps after using gps gate everythings fine,hope this helps.
Click to expand...
Click to collapse
Can you find the link for gps gate, what i found on google was kinda weird! please need it desperetly