Dear all, i've read lot about missing activesync connection...no solution found until now...
charging trough USB ok...but no activesync... TyTn II, AS 4.5 WinXP, ROM Laurentis (newest), sync was working perfectly for weeks...and now not more (miracules...).
Hard reset done, AS reinstalled. tested with differend cable and pc. My old Kaiser (model before II) connecting without any problems. repllog.exe exercises done, all combination advanced network, usb etc done....what other? can be mini USB hardware problem?....so far all possibly woodoos....
as ROM is not more HTC original, no warranty...
any advice will be very, very, very appreciated...
best regards
Toms
How is Activesync via Bluetooth? When you tried Activesyncing with another PC using another cable, was 'use advanced network functionality' switched off at the time? Some PCs just cant handle an AS connection with it on. You'll need to think about what changes you've made since it was working fine.
No need to worry about the ROM, there are steps in the wiki about how to restore your device back to factory original state SHOULD you need to send it in - read that. I've never flashed a custom ROM and even I've read it. It should be one of those things you read before doing any flashing.
Hi Flying Kiwi
thanks for your reply...my both PC and Laptop are not euiped with BT, so far i didn't tested. I've tested on both in combination with differend cables incl. switched on/off "advanced network functionality", hard reset, new AS installation.... On the same computers i can still connect without any problems my "old" Hermes (TyTn first generation). so far i'm suspecting that something is wrong in the PPC side, only the question what? working perfectly and just stopping to do this...without any new software installatione etc....
Flashing ROM's was no problem as long activesync was working correctly. Now unique way to flash back to HTC ROM will be option from SD card...but how to do this? i did found nothing about this...
I suspect something with RNDIS, but not clear idea yet...so far still no solution...so far pity that i need the PPC for my work with full functionality...
Similar question was posted on AT&T forum and the solution was as follows http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=104069
Woow...good hint!
Hi HBaer...thanks you finally some progress for me in this story...
it's working but instead to show "ubs" on the boot screen show "serial" (...and this is this what is disturbing the AS connection...as suspect not AS/PC but something wrong with PPC) how to change it???
best regards
TomSch
How are you connecting to your USB? If you are connecting through a hub, you will need to connect directly to a USB port not through the hub.
directly, no hub...the same connection was working perfectly and still is working perfectly with my old Hermes...
Refer to XDA Developers wiki and stuck at bootloader screen section http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
HBEAR, again top hint! original HTC ROM re-flashed ....but still no connection trough USB...trying re-boot on the screen "serial" and no change to "usb" after attachment to the USB cable...more and more suspect hardware issue, some method to check it?
best regards
Try sync with a different computer
done...with 3 laptops and 1 desktop PC....and check lot of very interesting inputs in forum on xda-developers, great source of information! btw i've placed my questions on the htc pages too....no any answer :-(...
I believe a "Force USB" HardSPL may fix your problem. There is a HardSPL sticky in the ROM Developement forum, go read up on it.
look here: http://forum.xda-developers.com/showthread.php?t=438232
maybe the soloution for your problem too??
check your registry-keys !!!!
Related
Hi,
since a couple of days, my XDA II doesn't sync any more. It has still worked finefor a long time, since I have updated to WM6.
With my Orbit 1 async is always working fine.
When I connect it to the PC, the PC is always looking for a USB Driver.
Configuration:
Win XP; Async 4.5
XDAII WM6 by Shekhar 70C40CS
What I've tried: - changing USB-Connection and cable
- hard and Softreset
- changing USB to PC advanced network
- reinstalled async
- trying another PC
- reinstalling WM6 - no way, cause there is no USB driver
Maybe, that it is a hardware problem; but I doubt it, cause everytime, when I connect it to the PC, the PC ist trying to install a driver. So I think, there might be a software problem into the Himalaya.
Any ideas?
Sync problem - missing Driver.
Same problem with me on my notebook. Ask for help in another thread a few week ago, and got the advice to swith to active sync 4.5. I did so on my desctop and it worked wonderfull. On my notebook I stayed on as 3.8 because of my xda II and my old mda I. After I upgraded all my three xda to German WM6 i switched to as 4.5 german. I was verry suprised to get that fault window about the missing driver for that prototype thing and changing the vendor.
Not a mess I still have the desktop to install .exe and then copy the .cab files I need to my sd-cards. It´s not the known problem with the firewall (zone alarm), but it is a good question why as an the desctop works and the notebook doesn´t. Next I try to install the copied as-file from the desktop. Don´t know if it helps, I post if it does.
Hi, I had exactly the same problem, but I solved it in seconds because of Your last thread, thanx.
I had configured my windows firewall with "no exceptions".
I reactivated /checked the firewall-exceptions for ActiveSync on the PC and activated the extended networkfunctions under usb to pc on the xda and immediately everything worked fine.
Solved my problem too. Nice to help you.
Fine that I helped you, it wasn´t my purpose.
I got rid of that dammned thing about the missing driver for Prototype.
Read the hints of Jo_III in Post #28 and #31:
http://forum.xda-developers.com/showthread.php?t=341221
and follow exactly.
Insert in /windows with the name changed, rename it afterwards.
No question, why this is possible without the massage that it is impossible, as you get it, when you try to replace directly, but it works!!
Then soft reset and change /settings/connections Advanced Network Funtionality to disable/unchequed.
The funny thing with me is, that on my Dektop-PC both works.
Advanced Network Funktionality enabled the driver is for the Prototype.
This funktion disabled finds a WinCe Device.
Both works fine. No freesed PPC when disabled any more.
On my own notebook I can connect to the PC only in disabled Mode. When enabled this prototype driver problem is still there.
On the notebook of my beloved wife as4.0 recognizes the PPC an a WinCE Device but has a problem code 10. Think it´s normal as it is 4.0 and 4.5 installs new usbdriver while upgrading.
I tryed to upgrade to 4.5 and the windows installer crashed. I love it, really nice. I don´t want to fix this, I think, for me it is OK to ignore this.
This funny behavior, as i discribed it above, all my upgraded XDA/Qtek (all three of them) do.
PS. I use the German Rom of Teijalk with HTC Home and SCLPC++ Cube and I love it. Works perfekt and really fast and stable even with lots of proggis on RamDisk and few RAMStorage left, still really fast with my Pluscom WLan Card.
The Link is:
http://rapidshare.com/files/88608779/WM6ger.zip.html
More stuff like this. Thank You - thombs up!
The info above is wrong.
Only on my Qtek this solved my problem. Both of my XDA can´t deaktivate RDNIS for serial connection, when I try to uncheque Advanced Net Funktionality.
Don´t know why, I did the same on the other device without an error.
(Now I examined, that I used Port 8 twice. Once for serial to USB connection and second for external GPS connection, so it wasn´t able to deactivate this funktion anymore. I changed Port and everything is fine again.)
Final problem solved
totoche330 got the solution to my XDA sync problem in the thread above.
After Hard reset (No,Yes,Yes) inserting and renaming the dll. Soft reset and deactivating adv net funktionality. Works.
Don´t know why it didn´t work as it worked with my Qtek with all the programs installed, but dosn´t matter.
The problem of my notebook might have some reason:
The missing driver is called a Remote Network Driver Interface Specification to USB (RNDIS).
I think, I disabled everything to remote, because of one up to 25 trojan attacks.
I cured my xp, but i didn´t do a new setup. On the other hand it´s the only XP-Pro SP2. Desktop and other notebook are Home Edition SP2, but this is not important anymore. All PPC sync and that´s what it was about.
Two or three hours work and all the progs are back again. I hope, you can solve your problems too. Good Luck.
Does noone can write a driver for the cf-slot of the backpack?
Sometimes after soft reset you have to cheque and uncheque adv net funktionality inorder to get synced!!
Hi, i have recently installed ms active sync 4.5. However my tytn ii will not establish a connection with my pc. It charges just fine but does not connect. I have searched all over but did not find a solution to my problem. i was wondering if it mightbe the cable i got with my device when i purchased it. it is a usb to "mini usb" like the motorolas and nokia 6300 use. Could this be my problem?
I doubt it's because of the cable (though could be). Try unchecking start>settings>connections>usb to pc.
I have the same problem, and have tried connecting with and without advanced network functionality.
activesync does not respond at all, even when trying to connect from activesync on my pc.
I have the same problem, charging o.k., but USB connecting not work
Before I had same problem. The reason was I have installed some 3rd party program what somehow blocked the sync.
I have un-installed this program but it couldn't help because the registry setting was modified by this software. So finally I ended up with a hard reset and reinstall everything. After that the sync just work fine again.
Sigh, i thought it might come to that.
hard reset 2x, no effect
flah rom from SD card, Duty V1 Daimond....no effect
flah rom from SD card, L26 V6 Daimond.... I have the same problem, charging ok, USB data connecting not work...
Well, hard reset complete to no effect. So frustrating!!!! I have been troubleshooting for ages and have nothing to show for it. Surely someone on this forum has solved this problen before.
Hi
I had the same problem following a rebuild of my laptop.
Problem traced to my firewall which had blocked the connection.
Once rule changed to allow no further problems.
Hi colinm, what did you do exactly? It may help me out of this situation.
Doesn't anyone know anything about this?
Yeah i had it get the latest update for active sync from windows its a latest driver pack goto teh windows home and look on there it sorted my one out
what version is it? i have 4.5 right now.
If you could provide a direct link that would be great.
I was trying in 2 different PC ( Vista, Win XP), but the same problem, cable is ok....
I would really like to know what the more experienced members think about this but no-one really seems to want to reply. also i would like to know is the usb data cable plug identical to the htc original handsfree plug which is an exact fit. as i mentioned before my data cable is more like a mini usb, like the motorolas use. it fits (not perfectly like the handsfree), charges but there is no recognition between the device and the pc (xpSP2 running activesync 4.5 which came with the device).
Please help, i may seem to be a noob but i have tried available advice and troubleshooting has become repetitive.
My Mobile Device Center from my Tilt to Windows Vista stopped working a few weeks ago. Tried everything to no avail.
there was one thing that i couldn't do while troubleshooting.
"Do the following:
Disconnect the device.
Open Network Connections in Control Panel on the PC.
Note If your Control Panel is set to Category View, open Network and Internet Connections, and then open Network Connections
Right-click the local area connection created by ActiveSync, and click Properties. In the Connect using box, Windows Mobile-based device is displayed.
In This connection uses the following items, select every check box (to select all protocols).
Reconnect the device."
i cannot see the network icon active sync has created. which leads me to believe that this might be the problem. does anyone know how to fix this?
will updating to SP3 do anything, gonna try will let you know.
link with answer:
http://forum.xda-developers.com/showthread.php?t=362679
thanks champ worked a treat. eventually.
Hi I have a fault with Activesync (Vista), I connect the USB cable to the PC and to the handset, the power indicator tells me that it's charging yet, the device is not syncronizing.
I have reset both the PC and the Device with no avail.
It was working OK about a week ago now nothing, I have not altered any settings and im running HYPERDRAGON III with radio 1.65.24.36 any suggestions???
You are required to search before posting, and seeing as this is a common problem I don't think you have met the requirements.
This is sort of an "advanced" users forum. If you don't search first, you won't get much help on here. Look at the top right, see the "search" click it, type in something and it should help you out. This is a very common problem, asked and answered many times.
I'll take a moment and try to help. It's just as easy as telling you to search.
I found a thread or two (the search is really time consuming. I don't find it to work all that great...find too much stuff unrealted to what you need). And they didn't help.
What I am only just not realizing is that it seems that the firewall with the Virus software may be interferring. If I turn off the firewall long enough to synch, it works.
What a pain, but that's what's working for me.
Never had this problem on XP.
Chillin like a Dylan
Thanks for the support and advice. I have followed instructions yet problem still pesists.
I have disabled firewall and Anti-Virus to no avail. When connecting the USB cable usually I hear a notification that the device is attached but this doesn't happen. Very puzzling!
Awesome problem solved. Reinstalled Wdinows Mobile Centre and all works ok now. Im not sure if this has any similarity but I know there was a Vista update the other day which may of interfered with the device drivers. Not sure.
But all is working well!
It'll be interesting to see if it keeps working well. INstalling WMDC was my first attempt at fixing. It appeared to fix, but the next time I went to synch, it didn't work again.
I spent the next 2-3 weeks reinstalling WMDC every tiem I wanted to sync, and it would sync.
I remain only able to do it if I disable my firewall (or reinstall WDMC, which I'm tired of). Of course, that could be vendor specific problem. I am using Trend Micro on my PC.
Nope issue still reminas, I'm pretty sure its the connectors in the Mini USB, on reading other forums I have discovered that the Mini USB port has been known to malfunction. This is due to the design of the port and the fact the cables shipped with the device are standard and not customised for the device.
I just wiggle around the socket a few times and hey it works (fingers crossed). Might justbrick it and order a replacment that will work if I can't sync any more.
I have also noticed that you have to wait after a soft reset for all of the programs to fully load. ESPECIALLY if you use BB Connect.
I believe this to be the true reason why rebooting a PC sometimes helps... it gives the Kaiser enough time to fully start.
instead of reinstalling WMDC, just make sure the service required to connect your device to your computer is running.
I believe its called windows mobile based connectivity. You wont be able to connect with that on manual. Switch it to automatic, as it sometimes likes to switch back to manual especially after a ROM flash.
Hello,
Firstly I want excuse that I open new threat and open it here, but please let me explain it why I do it.
I have O2 Stellar, with SPL:1.82.0000 and my USB dont work, and USB connector is OK and cable or USB port too. I try it at diferent PCs with diferent systems aka XP, Vista.
Main problem is that USB dont sync with ActiveSync or other, no "Tada sound" dont show "not recognize" really nothing action when I plug it to USB.
And charging is work only when PDA is off and light RED LIGHT but when is off, than no action, no light, no charging.
I know that this is threat for "Kaiser General" but I can live with charging only when is off, but I cant live withou coocked ROMs, I really try use all HardSPL new Radios, NBH from shippedroms copy to SDcard (Formatted to FAT32) and it only show "LOADING..." but nothing, more, still Loading.
I was tryed JumpSPL but it dont flash from SDcard, and USB is not showing and not working, that I cant use MTTY.
Please let this threat open, I really need HELP
Do someone know if this is Hardware or Sofware problem?
I cant send it to service, from my country is too expensive (like new phone)
Thank you in advance
Jozef Ziak
Edit: The handsfree is working perfect, I really dont know what is it.
i have the same problem i been through three phones already 1 that i used roms on and two brand new ones from warranty att said it's a hardware issue".they are sending me another phone.
I had almost a similar problem with my tilt at one point. Check your usb to pc settings and make sure you have "advance connection" (or something similar I can't remember exactly what it says) checked. On the rom I am using now shows something different there. I says "enable faster data sync" "uncheck if activesync doesn't recognize the device"
Thank you, but nothing reconize my PDA, no sound after plug, nothing when I go manualy to Bootloader, only show serial, not USB
same problem
Hi,
I had the same problem. I tried everything but nothing helped. I had 2 more months of warranty so they changed the main panel. After I got it back from the service it was working for 3 weeks long and now again died with the same issue.
Strange. I have to send it back to the service.
HI there , I had the same problem for about 4 month but i solved it >>> how ?
Just clean your htc USB port and check if it is broken or not and you will see that your issue will be solved brother
Dear All,
I am now reading over the forums for about three days. But still I dont have a solution for my sync problem. The problem is that after I flashed my kaiser it won't connect to activesync. But the STRAINGE think is, that when I put it in bootloader the computer does regonize my kaiser, and I can flash another rom on it.
I also got a MDA touch and when I am connecting that one to my computer, everything workes fine. So the problem is not in the computer. What did i already tried:
- turned off the advance USB settings on the kaiser
- reinstalled my whole WINXP and try to connect
- reflash in VISTA and WINXP
- Put the original ROM back
- check if the repplog is in the Windows file
- Put the firewall off
- Googled on every thinkeble words
So i think that the problem is in te phone, because my touch is normaly connecting. The only thing my kaiser is doing now is when i put in on the computer is recharing.
Does sombody have the knowlegde of getting my kaiser back to sync? It will let me sleep a lot better!
Regards,
Gertjan
usually truing off the option (Enable faster data synchronization) fix the problem...
this is the first time time I read about such problem that was not fixed by all you did...
there are some other things, they may not work, but they're worth of a try:
1. try flashing different radio, not only ROM
2. try changing the USB port on your PC
3. did you try syncing with another PC?
I had a similar problem with one of my PCs, it used to sync with no problems, then it stopped! the other PC i have syncs with no problems
all I did is disable the option (Enable faster data synchronization) in USB to PC in the connections tab
I really hope you'll find a fix soon
Do you use Dashwire? I have to kill the Dashwire process to make sync work... Just wondering?
If I understand your post correctly, you have 2 active sync devices. Are they by any chance named the same? I had that problem with my HP 3955 which is nothing more than a universal remote now but I charge it with my computer and it connects to active sync. Anyways long story short I named my phone Ron_Mobile when I got it which is what my PDA is named and I had active sync problems.
Sorry didnt help
Fingerlickin said:
If I understand your post correctly, you have 2 active sync devices. Are they by any chance named the same? I had that problem with my HP 3955 which is nothing more than a universal remote now but I charge it with my computer and it connects to active sync. Anyways long story short I named my phone Ron_Mobile when I got it which is what my PDA is named and I had active sync problems.
Click to expand...
Click to collapse
Thank you for your reply regarding my problem, but I changed the name and reset my device. After that he is still recharging and not connecting.
No Succes
duke911 said:
usually truing off the option (Enable faster data synchronization) fix the problem...
this is the first time time I read about such problem that was not fixed by all you did...
there are some other things, they may not work, but they're worth of a try:
1. try flashing different radio, not only ROM
2. try changing the USB port on your PC
3. did you try syncing with another PC?
I had a similar problem with one of my PCs, it used to sync with no problems, then it stopped! the other PC i have syncs with no problems
all I did is disable the option (Enable faster data synchronization) in USB to PC in the connections tab
I really hope you'll find a fix soon
Click to expand...
Click to collapse
Thank you for your reply, i did all the things you suggested. And still nothing changed. I flashed a diffirent radio, changed the USB port and I alrady tried to sync with serveral other computers. The strainge thing was, that after a reflash of the ROM of Athene (that I use mostly) I suddenly get this problem, and before I didn't have this problem at all...
well hope that someone else can help me.
partly solved....
jorra said:
Do you use Dashwire? I have to kill the Dashwire process to make sync work... Just wondering?
Click to expand...
Click to collapse
Dashwire? didn't know the existing of this service, so i searched it up. This service is a very good alternative for the time that I dont have activesync to work.
you might want to reflash the rom. i had the same problem after using -G- series 4 for almost 3-5 months, all of a sudden activsync stop working for some odd reason. so i reflashed with the latest -g- rom and now everything works.
itzstevo said:
you might want to reflash the rom. i had the same problem after using -G- series 4 for almost 3-5 months, all of a sudden activsync stop working for some odd reason. so i reflashed with the latest -g- rom and now everything works.
Click to expand...
Click to collapse
I installed the latest Garmin but still no succes..
I had the same problem. It happened when I flashed one of g-roms on my vista laptop. what I did was uninstalled and then reinstalled wmdc because apparently what had happened is something messed up with the drivers that recognizes my phone. I also hardreset just for good measure. I hope that helps.
david2327 said:
I had the same problem. It happened when I flashed one of g-roms on my vista laptop. what I did was uninstalled and then reinstalled wmdc because apparently what had happened is something messed up with the drivers that recognizes my phone. I also hardreset just for good measure. I hope that helps.
Click to expand...
Click to collapse
Nope didnt work, also tried on other computers and reflashed couple of times...
Same problem
Yes, I had the same problem as you. Some ROM will do that and some will pass that ActiveSync with no problem. Personally, I had to go back to the ATT original ROM and ActiveSync works again. Strange, but true.
I had the same issue a week ago...it ended up being the usb port on the phone...had to have it replaced. But--since you can still flash via usb, that probably isn't the problem.
I would uninstall active synch or mobile device center reboot and reinstall...then connect the device.
ok I had a strange problem last night with my wife's G1, it made me think of this thread. I solved her problem and I doubt you have the same problem but here goes anyways.
My wife just got a G1. I plugged it into my computer to load some MP3's on it for her since the G1 is supposed to act like a MicroSD card reader. It started charging but no USB connection was detected. It worked on her computer but not mine. After an hour or so I finally figured it out. The USB cable I use for my kaiser has a 3 foot USB extension on it. after using a different cable without an extension it worked. Try another USB cable.
P.S. "load some MP3's on it for her" HAHAHA I just wanted to play with her new toy!!!!!!!!!!!!
Broken?
Thanks for all the reply people, but still no succes Can the damn thing also just be broken??
Regards