Evry two times i switch off the phone, my MTeor looses its connection settings.
This makes it impossible to connect to the internet, wap, etc. In addition, my POP mail account is deleted.
Anyone had the same problem and found a solution ?
I called Qtek assistance but they dont know anything about this issue.
Luca
HTC WWE MTeoR
Radio : 1.06.00.10
ROM: 5.1.195.14955
Yes I have this problem too - and also a problem with call waiting - when you are on the phone and have call waiting enabled for "notification" the phone HANGS!
The MTeor has a terrible radio stack and needs urgent ROM fixes...
H
Same here. The HTC ROM is crap.
I have now updated my phone with the imate rom.
Just like the HTC ROM it looses all of the connecteion settings and email accounts and the battery life is just as crap.
This phone is a pile of junk.
Period.
I'm sure that future ROM updates will correct any problems MTeoR has.
If you recall, the qTek 9000 was far worse on it's first ROM version, MTeoR is much more usable as a v1.0 device.
@Pagemakers: I understand your frustration/dissapointment, but posting the same thing on every different thread in the MTeoR forum is not nice. Are you certain that your phone is OK? I have a MTeoR working with 3G Cosmote network and it works fine, no loss of settings whatsoever (I also have an 1GB microSD card in it, working fine). Plus, I get 3 full days AT LEAST on each battery charge (UMTS coverage all the time).
Try to send your phone for a service check or exchange it (might be a case of bad production series - happened to me with a Nokia N93).
Re;
Flashed with dopod rom . now work fine ! but only english
Hi,
i have flashed my mteor with the dopod rom..
Mail account and c° go away every 2 boots .... :-(
and when BT is actived i get less than a day battery..
etienne
hi guys, after i upgraded my tytn2 to ROM ver 3.29.707.0WWE, i can't connect to windows messenger. and it says that "There's a connectivity problem. Make sure you're in an area with good reception and try again".. i had already turned on my wifi and i can also open internet explorer.. what should i do?
help needed...
this problem happened to me when I first got my kaiser...
I could use Wifi with Live messenger - no problems, but when I turn into Data I get the same message
"There's a connectivity problem. Make sure you're in an area with good reception and try again"
the funny thing though is the problem was solved by itself
I used Parlingo messenger as a replacement....
I guess Windows Live is some kinda nuts... I had that problem for over 2 months and I never faced it after that!
Try - if you can- connecting from different places... I guess once the messenger is hooked, it'll continue to work properly....
this seems strange to say, but again most of M$ programs do the same
cheers
Without a solution right now you could install windows live and use the messenger via the internet connection you are getting?
Try to uncheck option under Settings/Connections/USB to PC
Check the date and time of your Kaiser, Messenger does not work if they are incorrect.
Hi all,
I wonder if anyone can resolve/give suggestion for my problem.
Basically i have experience problems connecting via Wi-Fi i.e the after activating wi-fi the phone will scan for available networks and give you the list. I then try to connect to my router (bt home hub which is actually speed touch) it does connect and stays connected for some time then suddenly the connection is dropped and under wifi it says that my access point is unavailable. If i turn wifi off/on again and scan for networks it comes up with "No visible Networks detected" even though there are like 5 access points in my house and i can connect to any of them using my laptop and old nokia e60. If i wait a while it will connect again but will not keep the connection. I have tried at home, work and some public places-every time is the same story.
Things i tried:
Soft reset/hard reset (many times)
Tried disabling phone radio in case3g chip interrupts
I tried with secure networks, open networks, different types of authentication/encryption, different router (more than 10) and every its the same story. I also tried several ROMS and ALL RADIO's available with the same result.
I am currently on Duttys_Diamv2.3 WWE RADIO 1.00.25.08, its a clean flash, nothing else is installed. I also have SPL-1.40Olinex installed (not sure if that could have an impact) The phone is vodafone branded btw (i had the same issue with vodafone rom which is why i decided to try other roms). I wonder if anyone has any thoughts/suggestions and would appreciate any help. Thanks in advance.
The same situation happened to my Diamond. I took it to the local dealer for HTC and after several days, I am told that the main board will need replacement. I am still waiting for it to be repaired as the parts had to be braught in from another country. I was also saud if the phone was less than a month old (which it is not) they would have replaced it with a new phone.
Good luck repairing yours and keep us updated.
omar302 said:
The same situation happened to my Diamond. I took it to the local dealer for HTC and after several days, I am told that the main board will need replacement. I am still waiting for it to be repaired as the parts had to be braught in from another country. I was also saud if the phone was less than a month old (which it is not) they would have replaced it with a new phone.
Good luck repairing yours and keep us updated.
Click to expand...
Click to collapse
Thanks Omar, I was kinda thinking that it may be hardware issue, but I don't anymore, I am trying something else actually as we speak. The only thing I haven't tried before is another hard SPL and I think that's the problem, I installed another version hspl1.34 and it seems more stable now and wifi keep connection, also with another hspl version (it was hspl 1.24) RAM under devise info>hardware showed 128, now it is 192. I will test in intensively and post my results here in case nay one else have the same issue. Hopefully I will not have to send it away for repair. Thanks for your info anyways.
In risk of sounding lame ...
Have ya tried 'Start' / 'Settings' / 'System' 'Wireless LAN'
Under Wireless LAN click 3'rd tab (strømtilstand in Danish - could be power-settings)
On that tab - pull the marker way to the left in order not to minimize the power consumption when tryng to hookup with the WiFi.
I had massive problems to get my local WiFi working at home - until I did this trick.
Best luck, Kindly
Kwasmir said:
In risk of sounding lame ...
Have ya tried 'Start' / 'Settings' / 'System' 'Wireless LAN'
Under Wireless LAN click 3'rd tab (strømtilstand in Danish - could be power-settings)
On that tab - pull the marker way to the left in order not to minimize the power consumption when tryng to hookup with the WiFi.
I had massive problems to get my local WiFi working at home - until I did this trick.
Best luck, Kindly
Click to expand...
Click to collapse
Yes i have thats the first thin you do anyways . I am now more than sure that the issue was with HSPL version 1.34, as soon as i got rid of it (installed hspl 1.24) all is fine.
With my phone, i tired all Hard SPL versions and even went back to stock SPL & Rom 1.37 & 1.93 and it still didn't fix the WIFI issue. it will work for 5-15 minutes then it will not work.
Anyway, I got a replacement phone as apparently they couldn't fix it.
pufeks said:
Hi all,
I wonder if anyone can resolve/give suggestion for my problem.
Basically i have experience problems connecting via Wi-Fi i.e the after activating wi-fi the phone will scan for available networks and give you the list. I then try to connect to my router (bt home hub which is actually speed touch) it does connect and stays connected for some time then suddenly the connection is dropped and under wifi it says that my access point is unavailable. If i turn wifi off/on again and scan for networks it comes up with "No visible Networks detected" even though there are like 5 access points in my house and i can connect to any of them using my laptop and old nokia e60. If i wait a while it will connect again but will not keep the connection. I have tried at home, work and some public places-every time is the same story.
Things i tried:
Soft reset/hard reset (many times)
Tried disabling phone radio in case3g chip interrupts
I tried with secure networks, open networks, different types of authentication/encryption, different router (more than 10) and every its the same story. I also tried several ROMS and ALL RADIO's available with the same result.
I am currently on Duttys_Diamv2.3 WWE RADIO 1.00.25.08, its a clean flash, nothing else is installed. I also have SPL-1.40Olinex installed (not sure if that could have an impact) The phone is vodafone branded btw (i had the same issue with vodafone rom which is why i decided to try other roms). I wonder if anyone has any thoughts/suggestions and would appreciate any help. Thanks in advance.
Click to expand...
Click to collapse
...I have the same problems with you
However, I think the problem may caused by different ROM versions.
My hTC version Diamond initially flashed a Chinese version ROM, and the WiFi connects well, while I changed to Dutty's most updated ROM, this problem comes and I cannot figure out why untill now.
Some friends also suggested to go to the Power Management and change WiFi to "Best Performance", I tried and failed again.
WiFi can open and connect to Routers located in library of my university, nevertheless it cannot open any pages.
I'm also waiting for any person that can solve the problem and then help us figure out why....
thanks in advance!
I got the same problem as most of the people have. and i think "Fail to turn on wifi" is a very common among guyz who got HTC TD.
I dont know what should be done, i almost tried every thing. actually my phone was locked to 3 mobile Sweden and i unlocked it but my wifi was'nt working before unlocking too but i did'nt gave attention to it. Now i noticed it.. is that any one know how to lock it again soo that i can send my mobile for repairs or, any one know what should i do.
I would recommend upgrading your radio and your rom.
Ive been rocking the setup in my sig for some weeks now and its been flawless, stable and fast.
which rom and radio you are using. can you please help me in this matter.
and i think its not a hardware problem because its showing that hardware is connected to my device as its shown in the screen shoot
Hi,
Im using AlphaZero V7 NLD,
Im have 1 wifi point in my house, downstairs.
even when im on the attic i have 80% signal strengt.
My router is a draytek 2820G router.
Wifi for me is very good. .. correctly, AZTOR V7 NLD is very good for me.
im on t-mobile network.
Radio Radio v1.00.25.05 , Radio v1.00.25.08, Radio v1.00.25.16, where all good,
now testing Radio v1.08.25.20, HDSPA signal is bit weaker atm.
my best radia atm i think, v1.00.25.08.
im betting, that the starter of this toppic, who has 5 access points in his house all have the same SSID. This is not the way.
Or make 1 big AP aera, bij connecting the AP's to each other.
of try to set every AP its own SSID, and its own Channel.
Louis
WIFI problem in HTC Diamond.........
I am trying connecting to my home wireless network. It finds the network but unable to connect to it. Any help please? Has anyone managed to get it connected to any Wifi? I ahve already set the power management to "best performace...no succes.......
(My laptop and O2 stealth does get connected to the same network and it an open wifi connection)...........PLZ Help.....
pranavsethi said:
I am trying connecting to my home wireless network. It finds the network but unable to connect to it. Any help please? Has anyone managed to get it connected to any Wifi? I ahve already set the power management to "best performace...no succes.......
(My laptop and O2 stealth does get connected to the same network and it an open wifi connection)...........PLZ Help.....
Click to expand...
Click to collapse
i am also having this problem, it can find the network, and can spend a minute or 2 trying to connect, and nothing happens. you posted this in february, did you find an answer?
Wifi & Bluetooth not detected by HTC Diamond
Someone pl help. My HTC Diamond is not detecting bluetooth devices neither is detecting wifi. It was earlier doing so and working fine however I believe after installing tweak TD & t3d config it has stopped working. I have installed new ROM also but to no avail. Can someone pl help!!!!!!!!
Wintermoonlight said:
i am also having this problem, it can find the network, and can spend a minute or 2 trying to connect, and nothing happens. you posted this in february, did you find an answer?
Click to expand...
Click to collapse
i also have the same problem. it detects a wifi (my router at home Aztech brand), then trying to connect to it, and then it always showed the wifi as "unavailable". i put my phone 2 mm distance from the antenna of my router it also won't connect. i have change dozens of roms, win 6.1, 6.5, 6.5.1, different cook, MTTY, all with no success.
i've looked for internet and google for answers, i seen quite a lot of forum has described this issue, but with no solution. most of the ppl suggest in various forums to pull the wireless slider to "Best Performance", ofcourse i have done that, but is just the same result.
i'm still trying searching for a solution for this, i hope is not a hardware issue because my warranty has already ended. i'm currently using Gen Y R4.1B rom
pufeks said:
Yes i have thats the first thin you do anyways . I am now more than sure that the issue was with HSPL version 1.34, as soon as i got rid of it (installed hspl 1.24) all is fine.
Click to expand...
Click to collapse
Ok consider now wifi will work by re-flashing the spl.
But what is the relation between spl (os/winmo loader) with wifi?
another dang unsolved diamond wifi?
bravo.
same problem with wifi on diamond2
With Original stock WM6.1 i was unable to connect at all, after flashed official WM6.5 upgrade everything worked fine. However i decided to put cooked rom because of battery life and perfomance issues. Dutty HG6 for Topaz seems to be with glitchy radio, it works sometimes, very rare, and i'm still not up to the pattern when does it happen and why. Pretty sure it's not a hardware problem - so everybody relax, we will find the solution.
which rom and radio you are using. can you please help me in this matter.
and i think its not a hardware problem because its showing that hardware is connected to my device as its shown in the screen shoot
wjenya said:
With Original stock WM6.1 i was unable to connect at all, after flashed official WM6.5 upgrade everything worked fine. However i decided to put cooked rom because of battery life and perfomance issues. Dutty HG6 for Topaz seems to be with glitchy radio, it works sometimes, very rare, and i'm still not up to the pattern when does it happen and why. Pretty sure it's not a hardware problem - so everybody relax, we will find the solution.
Click to expand...
Click to collapse
nope, i also put Gen.Y WM6.5 then the problem still arise.
i'll wait any solution until my diamond is totally wrecked
Hi,
I have a major problem. I can't get internet via gprs to work after the new 2.03 upgrade. I've tried two hard resets but nothing helps. The upgrade went fine and everything else works good, wifi & even MMS! which I think is strange since it uses gprs aswell... It sends and recieves MMS fine both with 3G, HSDPA & on Edge...
The connection wizard finds my correct settings and installs them, I've tried adding the correct settings manualy aswell. I've done it a million times before so I know it's correct. I have 3G coverage aswell since I can see the 3G on top. I don't use any static ip wifi connection either so the bug can be ruled out.
IE, Opera, Mail, Weather etc etc... nada, I can't get anything to connect. I see the arrows on top when it starts to connect and after a few seconds I get the connection error.
Please help, my phone feels worthless now...
try to get back to 1.93 and then re-flash the 2.03
Ok but is it possible installing this 2.03 again can help??? I mean so I don't have to go back to 1.93 first because I have no idea how to do it? I've not very experienced when it comes to changing roms since I always just flash the official ones...
Installed the older 1.93 again, still doesn't work
There seem to be no problem with the hardware since MMS works and uses GPRS, 3G, HSDPA & etc...
I think I give up, have to live without internet in my phone it seems
It's most likely a configuration problem rather than a hardware one.
Are you SURE the Internet access is configured EXACTLY to your provider's specifications?
Hi to all, please Owziee , did you fix your issue???
Hi, I´m from Spain and I have the same problem with my HTC Diamond. It was working very good with a cooking rom but after upgrade with the new original version from HTC don´t work GPRS connection.
I tested first with hard reset and second ,changing differents radios and spl in the way to found an answer for my problem but I didn´t found it.
I was checking the connection data from Orange for it was wrong but I saw all correct.
I created the connection manually first and automatically after it with the HTC Connection setup , but did´t work either.
Please Is there any way to fix it???.
Thanks in advanced
My problem is already solved: http://forum.xda-developers.com/showpost.php?p=3533866&postcount=2
Well i'm trying to have the wi fi router working on my kaiser to use it as an hot spot. Couldnt do it and asking myself if someone did better than me.
http://forum.xda-developers.com/showthread.php?p=4170499
(by the way: I tried the commercial wmwifirouter and my kaiser works nearly ok as a router)
First i tried the VGA version, NOPE.
Ok i tried the QVGA Version By wapvirus + HTC Sroll (always at the beginning of the thread).
Nope couldn't read the question it makes when it starts (YES or NO what? blank text)
Couldnt see the status, and couldnt see any button start stop (but could scroll down).
If i flag Use this settings automatically and restart the program it says running, connect to UMTS but cant see the wi fi network from my laptop...
Ok followed the post (always the same one) and found a never version..
Conflipper Internet Sharing.cab , this one seems better but is for VGA and cant see things...
Reading aruond they say thay they had to install the topaz comm manager to have it working always for vga,.. so ... where the he** is it?...
SO has anyone done better then me with this wi fi router and TYTN 2?
I' m a bit stuck with this software... Is there a way to change resolution to VGA ?
Thank you guys
From your post i can't tell if your device is qvga or vga, but you say you have tytnII so that must mean qvga. I have a TytnII as well and use the HTC CM Wifi Internet Sharing app, works perfectly.