Hi together,
I tried to flash my Charmer with a WM6 ROM. That failed, so I wanted to do a Hardreset --> Factory defaults. This failed because no OS was detected and it hangs up at bootscreen.
Going into Bootloader (3colors) and tried to connect via USB, the Bootloader shows me "USB" in the left corner, but if I start to flash an official ROM it says "ERROR 260 - Cannot connect to Device"...
Charmer seems to die... Several tries, no positive result...
While normal boot there are only shown 3 lines, but NO OS Version is shown up... Maybe no OS found???
What chances or possibilities do I have to get ANY OS on my PDA??
Heard something about flashing from SD??
How does it work, where can I find suitable Software/Manual for this? I do not have any ROM-Backup or something like that...
Help mee pleeeease...
I want to get my charmer reanimated...
Thx so far
bye
domi65
Hi
I am following the guides at
http://trinityguides.info/index.php?option=com_content&task=view&id=25&Itemid=66
and
http://forum.xda-developers.com/showthread.php?t=399827
Now I downloaded HardSPL 1.20 mentioned at
http://trinityguides.info/index.php?option=com_content&task=view&id=25&Itemid=66
and also tried the one at http://www.mediafire.com/?yxz2pu1oytg
I have installed USB driver on VISTA as per guide. my Bootloader shows USB.
But whenever I try to install either of the SPL it gives me an error
ERROR [270]: UPDATE ERROR
The image file is corrupted. Please check your Update Utility
Click to expand...
Click to collapse
Please help me with this
Ok Fixed problem
Perfect solution here
http://forum.xda-developers.com/showpost.php?p=2298295&postcount=6
Connect to your PC and make sure activesync has run properly and your phone is on.
Open Hard SPL and run the ROMupdate. Your phone will go to tricolour and it will come up with a communication error.
disconnect from PC but leave the phone in tricolour....DO NOT reset it.
Cancel our of the ROMupdate. connect the phone to the pc again and run ROMupdate again.
This time it will go all the way through and you will have HardSPL on your phone.
Check it by entering bootloader and it should show Olipro 3.2.
You can then flash away....make sure you always put the phone into bootloader before flashing.
Click to expand...
Click to collapse
Flashing now and will update soon
Hi, i would like to somebody helps me, i got my htc recently and i can't do it a hardspl i do all the steps and when it comes to almost finish gave an error i've tried with many different hardspl and nothing, i will show you the erros that gaves me... please help me with this problem, cause i can't do anything to my htc...
Hi
I have the some problem, I have follow this guide :
Step 2 - Upgrade to Hard SPL
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Before you proceed, check which SPL is on your device. Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If your SPL is 3.20.Olipro then you already have Hard-SPL on your device and can skip this step and proceed to upgrade your ROM or radio.
1. Download the Hard-SPL for P3600i (do NOT use any of the Hard-SPL's for Trinity/DoPod)
* Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
2. Unzip the Files, and click on ‘ROMUpdateUtility.exe’
Image Missing
3. Check the checkbox, and click ‘next’
Image Missing
4. Follow the directions in the window, and establish an activesync connection with your device
* Make sure the activesync icon is be green (finished synchronizing)
* Make sure your battery is charged
Image Missing
5. Check the checkbox, click ‘next’
Image Missing
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
Image Missing
7. After the version number has appeared, click next
Image Missing
8. In the following window, click ‘next’
after you click this, the flash will begin, so do not disconnect your device or do anything stupid on your computer
Image Missing
!NOTE! (quoted straight from Jon's post on first page)
WHEN FLASHING HARDSPL, IT WON'T WORK THE FIRST TIME - YOU WILL GET AN ERROR (CODE 260). THIS IS EXPECTED.
Quote:
Originally Posted by joncgde2
This is what happens.
You go to flash HardSPL like the guide says. LOOK AT THE SCREEN ON YOUR PHONE, YOU MIGHT HAVE SECURITY PERMISSIONS AND NEED TO MANUALLY ALLOW THE PROGRAMS TO RUN.
It looks like it's about to flash and then errors. BUT your phone is on the 3-colour bootloader screen! How odd. Well KEEP YOUR PHONE ON THE BOOTLOADER SCREEN, and unplug it from your computer. Exit the HardSPL program, RUN IT AGAIN, and FLASH THE PHONE AGAIN WITH HARDSPL (obviously connect your phone and stuff back to your PC).
The point here is this: the first time it will fail, but at least manage to get the bootloader up. With this bootloader up, exit the flashing program, restart it, and then you should be able to run the flashing program and have it complete.
DOUBLE CHECK YOUR PHONE HAS THE OLIPRO HARDSPL INSTALLED after completion, by soft-resetting (hold the power and camera buttons at the same time AND use the stylus to press the putton at the bottom of the phone. You might not get it the first time, but with practice you'll get the hang of it).
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated.
Image Missing
Image Missing
10. Once your device is finished updating, it will automatically soft reset. Click the ‘Finish’ button to exit the RUU program.
Image Missing
To confirm is Hard-SPL is on your device, manually enter Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If successful you will see the tri-colour screen and the following will be displayed
Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
but also after restart a lot of time HARDSPLromupdateutility.exe, I still have the same problem!
anybody may help me?
Now I have stratos image,
maybe is this the problem?
Hi
Pls I need help, I tried to upgrade my HTC P3600 then my computer crash so now every time I try to start my phone all what I got is a picture (HTC start mobility) and then nothing.
Pls help me.
Thanks
Hi gys, I think that this is my first post, but I want to share some solution for with you. The most important think with "connection" errors is to have HSPL installed correctly. I was trying to install on my HD2 universal ones, like Hard spl v7 and 9, but problems occured. So after trying everything, I found HSPL (on this forum) just for HD2. After that, everything wass like a charm
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
base167 said:
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
Click to expand...
Click to collapse
You have choice a wrong HardSPL !!!
Olipro 3.10 and 3.20 are for HTC P3600i and no working for TRINITY P3600.
So, now probabily you don't see "USB" on Bootloader when you connect you trinity on PPC.
Solution:
You must reload your H-SPL With SD CArd.
It's very simple:
searching for a Hard SPL for trinity device, example Olipro 1.20 and rename file "RUU_signed.nbh" ---> "TRINIMG.nbh".
Then copy file "TRINIMG.nbh" in a SD CARD and insert it on your Trinity; After that , make a Soft reset with stylus reset +power+camera.
Power bottom for update your Bootloader.
Now you would see your trinity working again
Davide
Hello!
I have this problem:
I've installed WM6.5 on my Trinity, and it worked well, but today I wanted to try WM6.1 (0.4.9.0 digital) also. The following happened:
Everything worked fine, but at 54% flashing my brother lifted the phone, possibly it lost the USB-contact, because the flasing stopped with an error message (unfortunately can't remember the error number). Since then if I try to flash it with WM6.1 or WM6.5, after 1% the phone resets itself, and the RUU gives a 270 error.
I have the original WM5 ROM also, but if I try installing it, after "Verifying information on your PDA Phone" screen I get a connection error 260.
What can I do???
After the phone resets itself, I can see the HTC logo, and the red letters and numbers, but that's all.
If I try HardSPL, I also get a 260 error.
Can you enter bootloader manualy?
If you can than see SERIAL change to USB when connected to PC it should be OK.
if you have a SD card, you can also try to flash "manualy".
- put your RUU... NBH at the root of the card,
- rename it trinimg.nbh,
- reinsert the card in the phone,
- enter in bootloader (power+cam+reset)
you will have a grey screen asking to push "power", do it and that's it.
if USB is well working, maybe you just need to reflash the hardspooler.
Thank you for your replies.
Fortunately I solved the problem.
I did the following:
1. To be sure, do all the stuff on a Windows XP machine
2. DISABLE "Allow USB Connection" in Active Sync so you see a small red X symbol next to the Active Sync symbol
3. Start the device into Bootloader mode (Cam+Power+Reset) and connect the device to your PC and make sure USB is written on the bottom of your screen (NOT Serial!)
4. Download splxploit (http://forum.xda-developers.com/atta...0&d=1180043588) and execute unlock on your PC
5. Follow the instructions
6. Download HardSPL (http://forum.xda-developers.com/atta...8&d=1185364317) and follow the instructions
7. Finally (to be sure) restart into Bootloader mode and check if SPL is showing "SPL-1.30.Olipro) - if this is the case you've done it !
8. Flash your preferred ROM via miniSD or USB connection
I m glad you solved this. Every day another new way of solving the flash problems.
Hi to All guys
i've got a trinity from my work and it has a custom rom.
I wanted to changed the rom so i download a wm 6.5 and erase the trinity with mtty. After that i try to install the rom with he RUUUupdate, but it get error 270.
Only in that moment i read on the bootloader and see that it haven't olipro or another HARDSPL installed.
So i looked for a solution and i try the unbrick with the splxploit. I did it and i get olipro on the bootloader, but i don't know how go on with install, if i use the exe i get 260 connection error.
Can you help me?
Hello i got a Opal viva t2223 stuck in "Smart Mobility" It show:
ONBL 1.27.0000
SPL 1.27.0000
GSM 03.29.90
OS 1.27.0.0
After that phone restarts and show the same again!!
WMDC and active sinc cannot regonize phone.
I can put phone in tricolor boot mode(power+vol, down), so drivers can be found(WMDC, Actve sinc still no), after drivers ok I can run HSPL2.00, HSPL1.26 etc.... but after 100% download in grey screen HSPL says "Error 270, file corrupted" and the boots still the same(not modified).
I already tried a lot steeps on this forum, but i stil cant run a fresh Os on fone.
I dont need to change language(portuguese brazil), I dont need to update my winmobile 6.1.
I want just to revive it with original OS or Custom OS.....Dont care about what OS I need just revive phone.
What better way???
Help and guide me please!!!
Thx