Database Develop

Can't connect with AS (Install a new ROM via my SD card)

Hi,
Can I install a new ROM via my SD card because I cannot connect to Active Sync? I've been searching for hours but still can't fix my problem.
I tried to upgrade the radio rom only, but after that there is no radio version, no phone or internet, system on MDA is VERY slow, and I can't connect to active sync.
I can get bootloader up, but I cannot install the stock rom I downloaded from this site, because i can't connect with active sync. I've tried to copy it to an SD card and install from there, but that doesn't work either. In bootloader I do not have USB at bottom left on my screen.
only
IPL 1.03
SPL 1.03
Any help would be MUCH appreciated.
Thanks in advance!!!!!

I have the same problem :-(
It would be very nice if there´s a solution for this problem
Thanks a lot
Daniel

You don't need activesynce
You just need to get into bootloader search for it then run the RUU.

kyphur said:
You don't need activesynce
You just need to get into bootloader search for it then run the RUU.
Click to expand...
Click to collapse
If USB is not showing up in the bootloader (rainbow screen) then the only known way to backup is via SD card. The RUU cannot be used in this case.
You'll want to dig out the original backup that you made when you first got the phone and do a restore boot. Restore the image from the SD card.
If you want the improved radio ROM, I'd suggest restoring from SD card, CID unlocking the device, upgrading to an AKU 2.x ROM (so you've got a 2.x bootloader) and then applying the 2.x radio ROM upgrade.

sd card
Check this
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=151
I installed a back up rom on my SD card with another phone of a friend of myne

same problem; wizard_radio version-2.25.11
will follow link in above post and see hoe it goes; anyone got any other comments?

no SD backup
well, funnily enough I ran the ROM backup as a precaution, but it seems a. not to have worked and b. to have wiped my SD card, so am buggered whichever way you look at it.
Does anyone have a backup image they could email/FTP to me so I can at least get to USB in bootloader?
THanks,
Jolyon

the CURE
ok, thanks to the tip from a99tandem.
Reset, holding down the camera button, allows you to go into boatloader, and you can flash a ROM from the PC using RUU. Bootloader comes up with 'USB' in the corner.
Thank god for that; that's 5 hours wasted...

unable to revert to O2 rom

Hi Guys,
i consider myself relatively experienced at flashing HTC devices having been using and upgrading for a few years but i've run into an issue on my CID locked G4. i upgraded to WM6 without issue and i tried to revert back to my O2 rom, the flash failed and i'm now stuck at the splash screen. I've tried to flash the original ROM from boot loader but i get a 101 error unable to connect(can see it in device manager). as i'm using vista i did a search and found some instructions and driver files but i get the same result. the only thing i can think of now is to CID unlock but i'm not sure it will help (unless it allows me to do the SD card restore). any ideas guys?
IPL:2.21.001
SPL:2.21.001
GSM:02.25.11
OS:10.1.0.811

OK., what you need to do is use a PC with XP, because i have read that vista PC's can get you into a lot of trouble. When you are at an XP PC, follow the instructions in my previous post
( http://forum.xda-developers.com/showthread.php?t=313354 ).
When you flashed the original ROM, and you succeeded in doing so, think real hard if you still want to upgrade to a new ROM.
If you still want to do that, stick to a PC with XP installed (no vista!).
If you did reflash a good ROM into your HTC you'll be one step closer to upgrading your ROM.
Read this post thourougly :
http://forum.xda-developers.com/showthread.php?t=298613
as this will help you in case you didn't CID unlock your device.
(thanks vippie; this is the clearest walktrough i could find!)
If you are really sure you CID unlocked your device, you can flash your device to any ROM you think is useful to you.
If your device is really CID unlocked, you should be able to flash any ROM that is posted on this forum.
I know that it is that easy, because i have tried every WM6 ROM that is posted on this forum
good luck, and i hope in the end you will have the ROM that you want....

thanks. my device IS CID LOCKED and i've tried to flash it from 2 XP machines so it is looking like its a brick thanks anyway.
for sale wizard with pretty 3 colour screen - sold as seen!!!

One thing you can try is use another USB to mini USB cable, i have had one cable that didn't connect really well.
Sometimes it worked but if i moved my phone the connection went down.
I just thought of that because it was a while ago that this happened - I threw away the faulty cable and had no problems after that.

tried 3 different cables too

knownuser said:
tried 3 different cables too
Click to expand...
Click to collapse
How much do you want for it? I need a new screen and body shell!

jabreu203 said:
How much do you want for it? I need a new screen and body shell!
Click to expand...
Click to collapse
was actually kidding i'd like to fix it but i'm open to offers PM me.

ok .....HELP
i've paid for the CID unlock which went well i then tried to flash the O2 default rom failed error 101 (connection) i then tried wizard love failed error (300) in italian.
so stage 2 was to use the sd card recovery i ran the utility and then followed the instructions r2sd all etc..all seemed fine i restored the image to the wizard and rebooted it still won't go past the splash screen i've tried re-flashing and hard reset still no go....please guys any help???

If you have a memory card take it out. Right click on ActiveSync and go to connection settings. Uncheck allow usb connections then try to flash. With windows XP...

tried to flash on a win2K machine (4 pc's thats the only one thats not vista) still get error 101 on the original O2 rom and 300 on the wizard love rom.
still no joy anyone have any ideas???
http://www.t-mobile.hr/mdasw/RUU_Pro...R_WWE_Ship.zip fixed i'm on a tmobile rom i'll try downgrading again.

Bootloader question/trouble

Hey there everyone, I am pretty new to this forum so I must apologize for throwing you all into the deep end. I recently purchased an o2 XDA mini S second hand from a guy on boards.ie here in Ireland. I got the phone and really liked it because it allowed me to get rid of my Dell Axim X3i and mp3 player and keep it all in one device.
After a little bit of more research I discovered that I could remove some of the bloatware from the o2 xda mini S by just hard resetting and choosing the basic option which I than did. Still not satisfied with the overall performance of the XDA I decided to try a rom upgrade. Not wanting to do a totall overhaul I decided to just do a radio upgrade first.
My device is sim unlocked, it was like that when I bought it. I used the latest wizard service tool to CID unlock the device before I even flashed the phone. I also used the wizard service tool to change the nk.nbf file within the o2 mini S radio update into 96000000-GSM.nb. I then used this file to write to the GSM radio code (Bdk 1) according to the wizard service tool in the hopes that it would upgrade my radio version.
Well when I restarted, nothing of the sort happened, on the boot screen I noticed I was now missing my GSM version and when the phone finally got into windows mobile, it did not pick up any signal even though beforehand it could. The phone also became super slow to the point where it was unusable.
I have gone into bootloader mode subsequently after reading on this forum and tried to reflash with a number of updates with active sync disabled and nothing else running with the phone connected via usb to the pc. None of the updates would even pick up the phone or allow me to flash it.
My phone is pretty much screwed, I have a spare so it is not that big of an issue but I would like to make this usable again if at all possible. So my question is how do I flash a rom while the phone is in bootloader mode?
P.S I forgot to include the Current boot screen details:
IPL - 1.05
SPL - 1.05
OS - 1.5.4.2

Hi,
You can use the Wizard Love Rom from here http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar

Hey there, thanks for the advice, I did download that ROM but like I said before, none of the roms manage to flash my XDA because they all cannot seem to connect to it. Activesync does not even pick it up in windows mode, and even when I have it connected in bootloader mode via usb and I double click on the love rom, it goes through the motions but never managed to "verify the information with the pda"

Try a stock Tmobile ROM but not from bootloader. Also, I would check the activesync app on the device. Make sure it's set to use USB as the default connection method.
A few other steps to try...
Uninstall ActiveSync and install an older version. If still no go, try a newer version.
Try a different USB cable and/or USB port.
Try a different computer with XP, not Vista.
Try flashing it without the SIM card or any memory cards.
If all else fails, you can try the SD card flashing method. There are instructions in the Wiki on how to do it, but always a stock ROM.
Try this one... http://forum.xda-developers.com/showthread.php?t=311027
Updated IPL/SPL and radio 2.69

Hey Devis, I think I have come one step closer, I tried all the suggestions that you made. Except well now my phone will not even go into the operating system when I switch it on. It will boot and the version numbers show but then it just resets itself.
I tried a different usb cable and I am not using vista, tried a different pc and the same result. The one place I did have some marginal success was the sd card method.
Basically what happened is that It backed up the OS from my phone and then reloaded it, not exactly what I wanted since the OS and rom are both screwed on the phone so my question at this point is, is there anyway using the SD card method to load one of the stock roms onto my phone?
I searched around the net and found the opposite to the "r2sd all" function, would be the "s2d" function, would that allow me to flash the phone with a stock rom?
Thanks for your time, I am going to call it a night here in ireland and head to bed.

Ok, if the phone resets then you probbably have a dead/dying battery. Charge it for about an hour or so using the wall charger, not the USB cable. Try to restart it and see if you can get in the OS. I was looking in the SD card method thread and some guy was successful at restoring the image from the SD even though his OS had died. He then had a fully functional phone.
The other thing to do would be to get the image file from someone that has a living and breathing wizard, preferably one with a stock ROM. Since this method is the equivalent of making an image of a PC using Ghost, the restoration of such an image to your Wizard should work just fine.
Just make sure that the other Wizard is SIM and CID unlocked. Or just go buy a Wizard from the store, unlock SIM and CID, copy the image on the SD and flash your device. Or... since u've got a new Wizard in your hands, just take the freaking thing appart and swap the guts return the store bought wizard to the store saying that the thing just doesnt freaking work!
As for the AT commands... it is possible that s2d would workfor you, it doesn't work in my wizard. from what i have been reading it appears that the bootloader is password protected and that password is randomly generated. I haven't played long enough with it to figure out how to get the password.
It looks like you've got some "trial and error" processes ahead of you. There is a wealth of info on bootloader AT commands on Wiki, nothing for the Wizard though. But something may work... not sure.
I could try to get you a ROM dump from my Wizard but I already am on SPL/IPL 3.08 and running WM6. the SPL/IPL version alone wouldn't allow you to restore from my backup.

Hey Devis, thanks for your time, just woke up here, will work some more on the phone today and let you know what is going on

Hey Devis, I did not even get a chance to fiddle around with the phone today, from being able to switch on less than 24 hours ago, it does not even want to switch on now so I am going to officially declared it a brick and move on. Will see if anyone can fix it for me, spent way too much time already when I should be working on my dissertation, thanks alot anyway

Sorry to hear that...
I have bricked one phone myself in the past... my old Pana GD87 and I absolutely loved that phone. I know how you feel.
Good luck with your dissertation.

Is it bricked? (Upgrade ROM error)

(I'm not 100% sure this is the correct forum, but since it is very ROM related it didn't feel all wrong to put it in here...)
Hi guys. After som serious flashing of cooked ROMs I decided for some unknown reason that I should try to restore a stock ROM. Now, being very tired as I was, i completely forgott that its probably a good idea to flash a new Stock ROM on the unit BEFORE flashing it with a signed SPL....so I just flashed the Signed SPL to the device. That in it self seem to have gone ok, because when I start the unit it say "SPL-1.15.0000". Problem is though that it also says "Upgrade ROM error, please try again"
Now, what should I do? Have tried put both signed and unsigned SPLs on the storage card and started up via the volume down/pwr button thingy, but that does not seem to do anything. I have also tried to attach the unit to a USB port when in tricolor mode ("USB" shows up on the screen) and tried the CustomRUU program. It finds the device and starts to "upgrade" (grey screen on the device with 0%) but then it just doesnt seem to get any further...
As the device was working fine with a custom ROM before I started all this, I suspect that the main problem proably is that I now have a Standard SPL with a cooked ROM, and that they collide sort of. I, as well as the Blackstone, is now stuck and I am all out of ideas what to do? Have also tried Hard and Soft resets, but that doesnt seem to change anything.
Help!

try removing the SD Card and put the phone into bootloader mode and re-flash the stock ROM! if this doesn't work ... still with the SD Card removed try flashing to USPL and flash the stock ROM again!
hope this helps

You can try USPL on your HD and flash a custom or stock ROM with it.

PapaDocta said:
try removing the SD Card and put the phone into bootloader mode and re-flash the stock ROM! if this doesn't work ... still with the SD Card removed try flashing to USPL and flash the stock ROM again!
hope this helps
Click to expand...
Click to collapse
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success (total success that is, I do get into the tricolored screen)). Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
I read somewhere that Stock ROMs should only be flashed from internal storage, not SD cards, is that true? If so, how do I go about accessing that storage now when it doesnt show up in the file explorer on my PC (PC recognizes it as USB device, "HTC Sync" but I get no file access to it).

improwise said:
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success. Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
Click to expand...
Click to collapse
just do uspl it will work

improwise said:
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success (total success that is, I do get into the tricolored screen)). Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
I read somewhere that Stock ROMs should only be flashed from internal storage, not SD cards, is that true? If so, how do I go about accessing that storage now when it doesnt show up in the file explorer on my PC (PC recognizes it as USB device, "HTC Sync" but I get no file access to it).
Click to expand...
Click to collapse
bootloader mode is when you power off the device and hold the volume button down and press power till you get the tricolor screen...
so here is what you need to do .
1. remove the sd card
2. go into the tricolor mode connect your device to the pc and make sure it says (USB) at the bottom
3. run the stock shipped exe from you pc
if that didn't work then you should try the USPL version.. and there is a guide if you are using vista.. i just tried and worked fine.. here it is
http://forum.xda-developers.com/showpost.php?p=3331078&postcount=153
and the reason i'm asking you to remove the sd card because if you have a rom (blacimg.nbh) it won't let you do anything it will try to flash from the sd card and right now you don't want to do that.
and you shouldn't put any rom into the internal storage of the phone..

PapaDocta said:
and you shouldn't put any rom into the internal storage of the phone..
Click to expand...
Click to collapse
What happens if you do that? will it try and flash over the flash? Proper *&@! it up?

nicelad_uk said:
What happens if you do that? will it try and flash over the flash? Proper *&@! it up?
Click to expand...
Click to collapse
i don't think anything would happen... the file will get deleted when you flash as the rest of the files in the internal memory

Thank you everyone! The USPL thing solved it, when I did it from a XP machine! The once bricked Blackstone is not alive an kicking again!
About USPL, I saw the workaround for Vista, but downgrading a few components to make it work just doesn't seem like a safe way to do it. And I cant help but to think that it might have unwanted side affects, ie affecting system stability. But maybe I am wrong?

Going back to shipped ROM without bricking?
Hi,
After reading this thread I am now a bit worried and, as a newbie, would appreciate maybe a "simple" answer to my question.
I''ve been experimenting with various cooked ROMs after following the guide in the WIKI for installing HardSPL and then putting the ROM file (BLACKIMG.nbh) on my SD card and installing it using the power on + volume down button method.
However, I now want to revert back to the original "shipped" ROM, which I have downloaded from the list of shipped ROMs via the WIKI (I downloaded the one which closely matched what was originally on my HD - as I didn't know how to backup the actual ROM on my HD at the time).
So, my question:
How should I put the downloaded original/shipped ROM:
RUU_BlackStone_HTC_WWE_1.14.405.3_Radio_52.49a.25.26_1.09.25.14_Ship.exe
into my HD without bricking it?! Do I just run it on my PC with ActiveSync enabled or do I need to do something to remove the HardSPL or something first?
Sorry if this has been answered previously but I get confused when a thread just makes loads of references to SPLthis and SPLthat etc.!

if you have the HardSPL already installed on your phone then you don't need to do anything more.. just connect your phone to the pc and let it sync (activesync enabled) and flash to any shipped rom you want by simply running the exe file..

PapaDocta said:
if you have the HardSPL already installed on your phone then you don't need to do anything more.. just connect your phone to the pc and let it sync (activesync enabled) and flash to any shipped rom you want by simply running the exe file..
Click to expand...
Click to collapse
Brilliant! Thanks for the simple answer Worked no problem!

SE Updater failed to install new rom, what is the best thing to do now?

Hello,
I know you guys got some excellent walkthroughs, roms, programs and threads where you've helped a lot of people out but I could really use some personal feedback. I had hoped to fix my phone using one of the excisting threads but unfortunalty I can't get it to work with those.
My problem is one I've seen more of in here, I used the SE updater and it froze at 53%, I did what the program said, reconnected and it froze again at 12%, and again, again, etc. So I disconnected thinking it might be a bad USB port. But then the updater didn't recognise my phone at all. So I used the mtty program suggested in some of the threads and I got past the red/green/blue screen but now it's stuck at the Sony Ericson logo, as if WM6.1 is gone.
This is what the red/green/blue screen currently states:
KOV110
SPL-0.78.0000
MicroP1-787
MicroP2-707
From what I gather this means I can't flash roms, right? I tried making it a hard-spl but when I use the tool it says it can't connect.
So is there anyway to get a rom on it and bring it back to life?
Thanks inadvance!

Get an original rom from here : http://forum.xda-developers.com/showthread.php?t=475482
copy .nbh file from the package onto your sd card and rename it to : Kovsimg.nbh then bring phone into boot loader via : vol down + power.
It should flash the rom now. i the problem is still present after that you
have to deal with mTTy but first try the flash...
i think you could also bring phone into bootloader without sd card inserted then connect usb cable, display should now print 'USB',and after that start rom update utility.
regards

meska said:
Get an original rom from here : http://forum.xda-developers.com/showthread.php?t=475482
copy .nbh file from the package onto your sd card and rename it to : Kovsimg.nbh then bring phone into boot loader via : vol down + power.
It should flash the rom now. i the problem is still present after that you
have to deal with mTTy but first try the flash...
i think you could also bring phone into bootloader without sd card inserted then connect usb cable, display should now print 'USB',and after that start rom update utility.
regards
Click to expand...
Click to collapse
Thank you for your reply, I will do as you said although I've already tried something similiar to this. I believe the problem was that I couldn't flash roms from my SD since I don't have the hard SLD. But I will try it anyway as soon as I get home.
In the mean time I would love to hear more ideas about how to fix my phone.

Ronnet said:
Thank you for your reply, I will do as you said although I've already tried something similiar to this. I believe the problem was that I couldn't flash roms from my SD since I don't have the hard SLD. But I will try it anyway as soon as I get home.
In the mean time I would love to hear more ideas about how to fix my phone.
Click to expand...
Click to collapse
You really need have to flash the HardSPL first as, based in your above post, you still have not done that. It will be useless to flash cooked ROM with that. If you can still power on your phone and you have an activesynch in your computer, i suggest you download the HardSPL first and update your phone using your PC. If you are successful doing that, then you can flash all you want.

original roms will still work with original spl... but nevermind =P

laurence0609 said:
You really need have to flash the HardSPL first as, based in your above post, you still have not done that. It will be useless to flash cooked ROM with that. If you can still power on your phone and you have an activesynch in your computer, i suggest you download the HardSPL first and update your phone using your PC. If you are successful doing that, then you can flash all you want.
Click to expand...
Click to collapse
My phone can still power on in the sense that it shows the Sony Ericson logo or that I can access the three collor screen. But it won't launch WM6.1. I also have a problem with updating to hard DSL. It does recognise my phone because without it connected the program finds nothing and with the phone connected it wants to start updating. It says ''updating from image version: (emply) to image version: 1.00.X1 Ipress next and it opens a progress bar on both my X1 and the PC. But it never goes beyond 0% and then gives me an connection error. I think it has something to do with not being able to get passed the Sony Ericson logo. I mean the hard-DSL program does recognise my mobile but activeSync is never active because my PC doesn't recognise a WinMobile phone (since it wont go past the Sony Ericson screen)

meska said:
original roms will still work with original spl... but nevermind =P
Click to expand...
Click to collapse
Really? That might fix my device then. Could you suggest a rom from the long list? Perhaps one that works on all versions? Because I'm dutch but my mobile has always been in english so I'm not sure what rom version I had. Except that it was identified as an R2 Rom by the Sony updater before it killed my X1...

Go here
Find the latest stock rom for your country (and perhaps your carrier) and flash it
No need to have Hard SPL for that

Mopral said:
Go here
Find the latest stock rom for your country (and perhaps your carrier) and flash it
No need to have Hard SPL for that
Click to expand...
Click to collapse
I'm now downloading the initial dutch R1 firmwire, could that one work?

Mopral said:
Go here
Find the latest stock rom for your country (and perhaps your carrier) and flash it
No need to have Hard SPL for that
Click to expand...
Click to collapse
Alright so I got an R1 original rom (I now realize that the R3's were originals aswell) and it worked! I'm not sure if it was the different rom or the formatting with FAT32 that did but it works again. So I'd like to thank everyone who was kind enough to reply.
The device is incredibly slow now but now I can use the hard-DSL installer, right? DOes anyone have a suggestion for a good rom to use?

laurence0609 said:
You really need have to flash the HardSPL first as, based in your above post, you still have not done that. It will be useless to flash cooked ROM with that. If you can still power on your phone and you have an activesynch in your computer, i suggest you download the HardSPL first and update your phone using your PC. If you are successful doing that, then you can flash all you want.
Click to expand...
Click to collapse
DON'T hard-spl if you're going to flash a stock ROM. And especially if you're going to use SEUS.
Try flashing the R3A first. The R1s are way slow, as you've seen.