Hello,
please help me, I take it to car charger, and after some little time it was stop working and is only off, I find two fuses but both are good, I dont know how I can soluted I try read something but everywhere is only about rlod but my leds dont lightning.
Please help me.
Forgive me for this but have you tried taking the battery out up to overnight range and put it back in to see if it lights up?
Thank you, but yes I have tryed another good battery.
Hello,
I tryed for many times plug and unplug battery and now when I conect charger it is lightning red light, but when I tryed push power on button it stop lightning.
Have you any solution?
This happened to me
I'm afraid its probably dead -- you'll need to send it in for service.
Mine was within warranty, so it was fixed by HTC. They replaced the motherboard.
I think in slovak republic ist htc service and I dont have it with warranty, that I cant send it.
but now is lightning red light until I press power button
jozinecko said:
I think in slovak republic ist htc service and I dont have it with warranty, that I cant send it.
but now is lightning red light until I press power button
Click to expand...
Click to collapse
You can still send it for repair even if it's out of warranty -- they'll just charge you for the repair.
Yes I know, but its too expensive, like new Kaiser, that this is no solution, and is alive if is light only red? but only until I push power button?
So you mean u cant start it at all?
Not even the screen flashes on then off?
try taking out ur sim card and Memory card to see maybe those might be problems.
I really don't know what the problem is.
Sorry I can't be any more help.
Helo,
Yes I do it, but only when I plug charger, only RED light but nothing more.
Is there some fuse or another part?
Hi,
Now I know what happend. Pda take full 12V from car charger, and have someone scheme about feed part?
But I cant send it to service.
Related
Hi, recently my extUSB broke down, so I was unable to coonect anything. My friend changed the connector in proffesional way with IR gun. But now Kaiser won´t even boot up, no vibration on startup, only green LED is lit up.
I bought D2, but I am curious if there is any way to fix it.
Thanks in advance
What does your friend say?
What happens if, while holding down the camera button (on the same side as the power button but further down), you press the power button to power it on - do you get a stripy screen? If you do, you can poke the stylus into the reset hole to reset the device out of the bootloader screen. What did the friend have to say about it - personally I'd much rather have a TyTN II which boots and works fine except for a broken USB port (I presume it was working fine before the 'repair'), than one with a shiny new port that won't work at all.
Nothing happens it looks like it is absoluttely dead.
The USB port was faulty, that was reason, why I let it change.
Well, it is strange, but actually I am very satisfied with with D2, even more than with Kaiser...
Well I suppose you could always get an expert to look at it but if its motherboard is damaged (or there's other hardware damage), it may be more expensive to repair than it's worth. You could see what your local HTC people have to say about it.
Flying Kiwi said:
Well I suppose you could always get an expert to look at it but if its motherboard is damaged (or there's other hardware damage), it may be more expensive to repair than it's worth. You could see what your local HTC people have to say about it.
Click to expand...
Click to collapse
Or you could sell it in the market section, plenty of people that would like to get a crack at fixing it or use it for parts.
Hi, I just encountered the very same issue. I know I'm ressurecting a very old thread, but I rather do this than creating a new one
I flashed my Kaiser with Android about two months back. Everything was quite stable, no hardware issues. Suddenly, it won't turn on.
When I plug a charger in the extUSB, the orange LED won't show up. And if I try to turn on the phone, the green LED shows up and stays solid. However, the short familiar vibration isn't there and also the screen remains black. Nothing was wrong with the USB port. I tried multiple chargers...
janys said:
Hi, I just encountered the very same issue. I know I'm ressurecting a very old thread, but I rather do this than creating a new one
I flashed my Kaiser with Android about two months back. Everything was quite stable, no hardware issues. Suddenly, it won't turn on.
When I plug a charger in the extUSB, the orange LED won't show up. And if I try to turn on the phone, the green LED shows up and stays solid. However, the short familiar vibration isn't there and also the screen remains black. Nothing was wrong with the USB port. I tried multiple chargers...
Click to expand...
Click to collapse
Have you tried to reflash or hard reset?. Also maybe your battery is gone..try another one.
Some things to try
janys said:
When I plug a charger in the extUSB, the orange LED won't show up. And if I try to turn on the phone, the green LED shows up and stays solid. However, the short familiar vibration isn't there and also the screen remains black.
Click to expand...
Click to collapse
I realise you cant flash if it's not booting but if your battery has sufficient charge remaining (won't work if it's flat) it'd be worth trying a hard reset using the D pad key + stylus in the hole method (can be done at switch on time without needing a full boot).
Nothing was wrong with the USB port. I tried multiple chargers...
Click to expand...
Click to collapse
How do you know that a fault hasn't now developed with it - I wouldn't rule that out at this stage. Have you tried a known good battery that is fully charged in the phone also is it the original charger you are trying (not all chargers with the same plug are compatible)? Are you able to get the bootloader screen to show and if so, what does it display?
Flying Kiwi said:
I realise you cant flash if it's not booting but if your battery has sufficient charge remaining (won't work if it's flat) it'd be worth trying a hard reset using the D pad key + stylus in the hole method (can be done at switch on time without needing a full boot).
How do you know that a fault hasn't now developed with it - I wouldn't rule that out at this stage. Have you tried a known good battery that is fully charged in the phone also is it the original charger you are trying (not all chargers with the same plug are compatible)? Are you able to get the bootloader screen to show and if so, what does it display?
Click to expand...
Click to collapse
No bootloader, no nothing - just black screen (there's not even a hint of backlight). I'll try a different battery today.
I tried using my old AC charger, my colleague's AC charger (for TouchPRO2), USB cable... the orange LED still doesn't come up.
What's the hardreset using Dpad key? I tried holding the power button + camera and also holding the two "context" keys (above explorer and messages buttons) and touching the reset button with the stylus.
I'll see whether a different battery will do the trick.
Thanks a lot for all your suggestions, guys! Much appreciated!
janys said:
No bootloader, no nothing - just black screen (there's not even a hint of backlight).
Click to expand...
Click to collapse
What's the hardreset using Dpad key? I tried holding the power button + camera and also holding the two "context" keys (above explorer and messages buttons) and touching the reset button with the stylus.
I'll see whether a different battery will do the trick.
Click to expand...
Click to collapse
The context key one you mentioned is what I refer to as a D Pad hard reset. The one where you press the power button while already holding down the camera button is how to get into the boot loader - it's all explained in the Kaiser wiki. Sounds like another battery is definitely worth a shot - especially if you only have one (I have 3 for my Kaiser and on some days with heavy GPS use, I need all of them). What happened between it working and not working - what were you installing or doing with it?
Flying Kiwi said:
The context key one you mentioned is what I refer to as a D Pad hard reset. The one where you press the power button while already holding down the camera button is how to get into the boot loader - it's all explained in the Kaiser wiki. Sounds like another battery is definitely worth a shot - especially if you only have one (I have 3 for my Kaiser and on some days with heavy GPS use, I need all of them). What happened between it working and not working - what were you installing or doing with it?
Click to expand...
Click to collapse
I tried another (fully charged) battery from my gf's Kaiser today. No change. When I press the power button, the green LED shows up and stays solid (no blinking/flashing). Screen is black, no short vibration. I tried all sorts of hardresets and also tried to get into the bootloader. No luck.
Also, I took my multimeter and measured voltages on the charger, the battery and the pins in the phone where battery resides. Everything seemed to give a correct voltage. So it's really not a power issue
Thanks for all your help, but I'm afraid I have a total brick in my hand.
My Kaiser
Hi I have a HTC Kaiser I bought the first week it came out and it was f=ine for quite a while but 6 months ago it stopped working. It'll go to bootloader but won't flash. When trying to turn it on it'll go and just get stuck on the splash screen. I figured it was a battery because I'm very hard on my phones but I just got a replacement battery last week and all 3 of my batteries act the same way. I may have been trying to flsh went it went down it was a few months ago so I can't remember.
--- Other things to note
My Kaiser got wet and I had to have the usb port replaced and the dpad replaced. The usb acts fine but the middle dpad button does not work
The charging light will stay orange or green after I unplug the charger
After reading for the last week I think its either bricked or maybe has a bad hardspl on it?!?
Thanks in Advance for any help you guys may give.
jaygriggs said:
My Kaiser got wet and I had to have the usb port replaced and the dpad replaced. The usb acts fine but the middle dpad button does not work
The charging light will stay orange or green after I unplug the charger
After reading for the last week I think its either bricked or maybe has a bad hardspl on it?!?
Click to expand...
Click to collapse
Time for it to visit the same phone repair shop (or HTC) again for an assesment/possible repair if economically viable. If it's only recently got wet, you may be able to catch it before corrosion sets in and causes any damage but if it's not dryed out/cleaned quickly, the damage (from the resulting corrosion) will eventually show up (possibly in all the ways you've described).
So I used to have a G1 until last year, then I gave it to my friend. My friend returned it in broken. Seems like she dropped it a lot. [typical drunk college freshman ]
Anyways, I had an engineering SPL, recovery flashed, and biffmod or superd [wow brings back memories] on the phone.
The phone won't even boot. I press the power button, no LED backlight. I plug it in, no charging LED. I changed batteries, nothing. Can't get into bootloader/fastboot/adb/recovery.
Is this a brick that can be repaired or am I SOL?
Does it even come on?
It does not come on.
So you are saying camera+power, home+power, etc... will not take you anywhere?
What come up when you press those ket sequence?
Like I said, I am unable to boot into fastboot/recovery/normal boot. I don't even see the G1 logo. The LED back light doesn't even turn on.
I thought with a brick you're still able to see the G1 splash screen, so I don't know what to call this.
Looks like you have a black screen. Since you said that your friend drop it constantly it must have broken a wire or something that cause the screen to go black.
Bleh. So much for practicing cooking ROMs with that phone :[ thanks for your help!
Doesn't seem like a JTAG or whatever can fix this issue.
does the light go on when you charge it? or plug in a usb?
could be a dead battery..
From the first post
"The phone won't even boot. I press the power button, no LED backlight. I plug it in, no charging LED. I changed batteries, nothing. Can't get into bootloader/fastboot/adb/recovery."
any other suggestions?
well what im saying is maybe the battery is completely dead... did you try booting while plugged into a charger? lol stupid question mayb but im jus trying to cover all fields before we assume you have a brick
Lol. Like I said, I changed batteries. As in I replaced it with another one.
And yes, I did try booting with it charging, which is why I noticed there's no charging USB
Sent from my HTC Glacier using Tapatalk
ooo ok... dam that sucks, im not sure what else it could be. unless you dropped the phone a lot lol
Am I able to fix it with a JTAG? or is this kind of brick unfixable?
Hello, sorry if this question had been posted before. I just confusing with my Xperia Z1. It's just blank screen, no Sony logo, no boot animation, etc.
I've tried to hold power+vol up but nothing happen. When i put the charge on and i press the power+vol up, it vibrate three times and nothing happen.
What should i do with this?? I hope it's not hardware failure.
Thx for the answer and suggestion.
did you flash anything prior to it going like that?
Sent from my C6903 using Tapatalk
7supreme said:
Hello, sorry if this question had been posted before. I just confusing with my Xperia Z1. It's just blank screen, no Sony logo, no boot animation, etc.
I've tried to hold power+vol up but nothing happen. When i put the charge on and i press the power+vol up, it vibrate three times and nothing happen.
What should i do with this?? I hope it's not hardware failure.
Thx for the answer and suggestion.
Click to expand...
Click to collapse
When you hear the three times vibration then you shutting down your phone and after that the phone is turned off completely, then leave it under wall charger via USB or Dock for minimum 4 hours, if it do not turn on then you have to flash a new Firmware OR Repair via PC Companion. Download Official Sony PC Companion and repair your phone. Other way is to use Flashtool and download the latest FTF from Mega Collection and flash it. Then it should turn on.
hi
i have the same problem with my z1 xperia
the pc companion wont see my phone to preform any kind of repair
any ideas
thanks
if nothing is happening just the LED red blinks even when you put the device in the charge, its hard bricked and will be fixed just with opening the phone and relive it with test point ...
maybe this thread will help you:
http://forum.xda-developers.com/showthread.php?t=2646405
7supreme said:
Hello, sorry if this question had been posted before. I just confusing with my Xperia Z1. It's just blank screen, no Sony logo, no boot animation, etc.
I've tried to hold power+vol up but nothing happen. When i put the charge on and i press the power+vol up, it vibrate three times and nothing happen.
What should i do with this?? I hope it's not hardware failure.
Thx for the answer and suggestion.
Click to expand...
Click to collapse
If it's brick, no prob, let's begin
Requirements:
The latest Flash Tools version, the latest FTF file of your phone, or any FTF file you want
Plug your phone to AC charger for about one or two minutes, and if you see red LED, now your phone is OK
1) If your phone has more than 50 percent charges, you can unplug it
2) If it has less 50 percent, let it charge for about an hour or more till it reaches 70 percent
So, no matter the first way or second, after you unplug it, now you can now connect your phone via USB and flash it
If you do everything correctly and if nothing goes wrong, after flashing, you can use your phone without any problem
If you couldn't do it, inform me to help you more
Look at the micro sd slot. Is there a red stripe? Or white?
If red, it's a water damage
Sent from my C6903 using XDA Free mobile app
I had also a blinking light.. it was a broken accu.
l92 said:
Look at the micro sd slot. Is there a red stripe? Or white?
If red, it's a water damage
Sent from my C6903 using XDA Free mobile app
Click to expand...
Click to collapse
It happened exactly the same with mine. I was on stock rom, and went to the swimming pool with it. But the stripe is white.
I cannot turn it on and only get the red light blinking when is plugged into the charger...
Help...
Miguel Pereira said:
It happened exactly the same with mine. I was on stock rom, and went to the swimming pool with it. But the stripe is white.
I cannot turn it on and only get the red light blinking when is plugged into the charger...
Help...
Click to expand...
Click to collapse
Try the hard brick fix (if you have warranty send to Sony instead). I doubt it'll do anything because it seems by your decription the hardware is damaged physically, but its worth a shot.
kentexcitebot said:
Try the hard brick fix (if you have warranty send to Sony instead). I doubt it'll do anything because it seems by your decription the hardware is damaged physically, but its worth a shot.
Click to expand...
Click to collapse
I already sent it to the warranty. Now we play the waiting game...
zony xperia z1 bricked
I have the same problem !! PLS HELP !! THE PHONE IS DEAD !! My pc don`t recognize the phone !! no led... the phone not charging! what to do?? help please my z1 bricked today while updating Monster'$ Rom my Phone is entirely lifeless ... no LED light, NOTHING
When connect to PC... nothing at all happens, doesn't even pick up the phone!
Have tried VOL + and power
VOL - + power
VOL - and power
Still NOTHING... phone is DEAD
Please help me friends
Please Help any Dev!!
Please i need help, i hard bricked my z1 c6903 ,restoring a backup with unlocked bootloader , this time the pone is totally dead. When in plugg in it blinks a red light.Im reading all about this and im a bit confused ,can anyone help me please?I really appreciate if u can.Best regards
SANTUMIL said:
Please i need help, i hard bricked my z1 c6903 ,restoring a backup with unlocked bootloader , this time the pone is totally dead. When in plugg in it blinks a red light.Im reading all about this and im a bit confused ,can anyone help me please?I really appreciate if u can.Best regards
Click to expand...
Click to collapse
srichinu said:
I have the same problem !! PLS HELP !! THE PHONE IS DEAD !! My pc don`t recognize the phone !! no led... the phone not charging! what to do?? help please my z1 bricked today while updating Monster'$ Rom my Phone is entirely lifeless ... no LED light, NOTHING
When connect to PC... nothing at all happens, doesn't even pick up the phone!
Have tried VOL + and power
VOL - + power
VOL - and power
Still NOTHING... phone is DEAD
Please help me friends
Click to expand...
Click to collapse
7supreme said:
Hello, sorry if this question had been posted before. I just confusing with my Xperia Z1. It's just blank screen, no Sony logo, no boot animation, etc.
I've tried to hold power+vol up but nothing happen. When i put the charge on and i press the power+vol up, it vibrate three times and nothing happen.
What should i do with this?? I hope it's not hardware failure.
Thx for the answer and suggestion.
Click to expand...
Click to collapse
ali_assaf said:
hi
i have the same problem with my z1 xperia
the pc companion wont see my phone to preform any kind of repair
any ideas
thanks
Click to expand...
Click to collapse
NiM72NiK said:
if nothing is happening just the LED red blinks even when you put the device in the charge, its hard bricked and will be fixed just with opening the phone and relive it with test point ...
maybe this thread will help you:
http://forum.xda-developers.com/showthread.php?t=2646405
Click to expand...
Click to collapse
Drain your battery completely
By Pressing and holding volume up and power button for 15 second, no vibration dont worry just hold it for 15 seconds and forget your phone for 1-2 days
Get working charger and usb cable check it then connect charger to phone there should be red light
Leave your phone for 3-4 hours
Now disconnect your phone from charger
Again check usb cable and drivers in pc
Open flashtool and get stock ftf ready for flashing
Once the dialog box appears with phone's animation
press and hold just volume down button and connect your phone with pc and immediately Release volume down button as soon as dialogue box disappears
Then disconnect phone when instructed in flashtool and wait for 4-5 minutes
Now try to turn on the phone.
Main thing is to have patience
This should work as i have my phone in same hardbricked state twice and this brought life in my phone back..!
This fixed mine
https://www.youtube.com/watch?v=GelRGJrL08s
sony z1 red light blinking problem
i have sony z1 with red light blinking problem while charging or powering on i tried flashtool with ftf and pc companion my pc not recognice it please help me
I've had exactly the same problem, nothing but the blinking red light. I replaced the battery (around $6 on aliexpress) and the phone worked again!
Berenpak02 said:
I've had exactly the same problem, nothing but the blinking red light. I replaced the battery (around $6 on aliexpress) and the phone worked again!
Click to expand...
Click to collapse
I hope, your solution works for me too. I ordered a battery and waiting for delivering it. If it won't work, I'll write here to help someone like us who wants to order a new battery.
Edit:
After battery changing, the phone worked. I don't know why, but it had been locked and rebooted repeatedly. Then I resetted to the factory settings. After that, it has been started to run well.
My Z3 compact is dead. It will not start after I shut it off.
I've loaded it with magnetic charger and USB cable and will not start. No lights and it does not vibrate.
I have tried to connect it to my computer and also printed on the yellow button next to the SIM card without result.
Someone who has experienced something similar?
Important
Weird !
U Didn't Do Anything Wrong ??
It is not rooted or jailbreak and not dropped to the ground. It has been in freshwater.
Today I have send it for service.
CW1980 said:
My Z3 compact is dead. It will not start after I shut it off.
I've loaded it with magnetic charger and USB cable and will not start. No lights and it does not vibrate.
I have tried to connect it to my computer and also printed on the yellow button next to the SIM card without result.
Someone who has experienced something similar?
Click to expand...
Click to collapse
I got the exact same problem TWICE a few months ago. I died completly random.
First time I send it to a repair center and they fixed it. Secend time, it came back to life after a few days:S.
I still thought it was weird behavior, so I send it to the repair center and explained very clearly what was my problem.
I think it also came alive the first time and they send it back.
I recomend you to wait a few days and try again. If it comes back to life, claim your warranty and EXPLAIN VERY CLEARLY WHATS WRONG.
Else claim your warranty anyway.
Good luck
I am experiencing exactly this issue. Tried all the usual stuff - reset button, power + Vol-Up, long press, etc. No use. Phone is just dead and refuses to wake up. It is not rooted, didn't drop it, didn't even get it wet. Will take it to the service center soon.
I recently installed project spaghet x with evolution x 2.3 gsi with kraken kernel . It worked perfectly and then I came across a new recovery for j7 prime called skyhawks recovery. I wanted to try it out and installed it. It still booted and so I left it like that and charged it overnight and this morning I see that my phone no longer boots. Cant get into download mode or the recovery either. Nothing happens when i hold power button or any button combination Please help me fix it. any help is really appreciated.
EDIT: Thankyou for all the support but, I nearly went crazy because of my phone but I finally figured it out by useing a homemade usb jig to get it into download mode.
still charging when u connect charger? or no response on screen at all?
if no response, congratulation, your phone is dead. and you can sell it to me if you want.
but if you not believe what i say, you can wait more longer until other member give you the answer.
but if,, the led light still there and the screen showing the battery level when you put on the charger, so your phone still can survive.
leo31 said:
still charging when u connect charger? or no response on screen at all?
if no response, congratulation, your phone is dead. and you can sell it to me if you want.
but if you not believe what i say, you can wait more longer until other member give you the answer.
but if,, the led light still there and the screen showing the battery level when you put on the charger, so your phone still can survive.
Click to expand...
Click to collapse
Nothing happens when I press any of the button combination no charging display no led no nothing
santhosh ravi said:
Nothing happens when I press any of the button combination no charging display no led no nothing
Click to expand...
Click to collapse
What happened when you connect to pc? Any response? If still no response, your board is dead.
Just pm ne if you want to sell it, i need part replacement
leo31 said:
What happened when you connect to pc? Any response? If still no response, your board is dead.
Just pm ne if you want to sell it, i need part replacement
Click to expand...
Click to collapse
I fixed it with a USB jig