Related
Hello,
I believe I have a real 'tough' scenario:
My BA (WM2003) was running normally till yesterday where it simply 'froze'. I tried restarting it, (soft and hard) and it kept stalling on the (IMate) splash screen and didn't proceed to WM. I left it to battery drain completely.
I came to work this morning, and literally tried everything:
Standard Upgrade using the Imate original exe (PDA2k_WWE_14000_176_11200). doesn't recognize the phone anymore.
Tried the MaUpgradeUT_noID with the nbf files (radio, ms and nk). In all cases the upgrade starts and gets interrupted in the middle with a 'weird' error and the BA display fades as the signal led goes RED (constant, no blink). I have to take the battery out, back in.
Tried the mtty set 14 0 / task 28 sequence with no result. (The info commands return a garbled sequence which makes me assume that my bootloader got corrupted).
Any advice would be appreciated.
Thanks a lot.
W.
wzaatar
Read in another post that you got no reply on this one.
Well it seems like nobody can come up with anything that would make more sense than what you have done.
My wording is when everyting else falis go back to the original rom and start from fresh.
If you can't flash an original rom in the ship.exe or the extract form you need to send it in.
Does your device react to hard reset ?? at least you should get a boot screen.
Have you tried Bootloader mode?
I know that this is a really stupid idea.. but have you tried putting it in bootloader mode, and then trying to upgrade? Or maybe throw a WM5 rom on there, and downgrade again! Worth a try until you send it in!
Thanks for the replies guys, I really appreciate the help.
I figured out that I had two distinctive problems:
1. The constant red led light, after a lot of research, it turned out that the battery was defective. Changing it solved the problem.
2. Now, I am able to flash the ROM (Tried it a couple times so far) with the orginal or another one. It flashes correctly, but only if I use the NoID flash program, else it will return a MODEL ID error. And when I reboot it, it stays stuch on the 'Imate' or the bootscreen and I don't get the WM to load (As if it freezes)...
3. I don't think I can upgrade to WM5 as I need to shrink the EXTROM size? Can this be done through some 'task' or other command in mtty for example?
Thanks for your suggestions.
Cheers,
Wadih.
Hi,
I used to upgrade roms all the time on my 8125 and never had a problem - until a couple of days ago. I tried installed the wm6 "most beautfiul" rom on my ppc and it bricked my phone. After many attempts I finally realized that I needed to install the official cingular 225 rom (available on the site) in order to get my phone to work. Since then I have tried downgrading to button and to wizard love with no success. My ultimate goal is to get to WM6. I have tried unlocking and have read all the threads and followed the directions but I cant switch roms. Can someone please help me with this. I am getting desperate.
thanks
ecomajor said:
Hi,
I used to upgrade roms all the time on my 8125 and never had a problem - until a couple of days ago. I tried installed the wm6 "most beautfiul" rom on my ppc and it bricked my phone. After many attempts I finally realized that I needed to install the official cingular 225 rom (available on the site) in order to get my phone to work. Since then I have tried downgrading to button and to wizard love with no success. My ultimate goal is to get to WM6. I have tried unlocking and have read all the threads and followed the directions but I cant switch roms. Can someone please help me with this. I am getting desperate.
thanks
Click to expand...
Click to collapse
do you have a G3 or G4?
What are your IPL/SPL?
Which other ROMs have you had installed on this wizard?
ecomajor said:
Hi,
I used to upgrade roms all the time on my 8125 and never had a problem - until a couple of days ago. I tried installed the wm6 "most beautfiul" rom on my ppc and it bricked my phone. After many attempts I finally realized that I needed to install the official cingular 225 rom (available on the site) in order to get my phone to work. Since then I have tried downgrading to button and to wizard love with no success. My ultimate goal is to get to WM6. I have tried unlocking and have read all the threads and followed the directions but I cant switch roms. Can someone please help me with this. I am getting desperate.
thanks
Click to expand...
Click to collapse
So, you start a new thread with the same problem you posted in another thread hoping to get an answer??
My answer to you is the same one I posted to you before --
READ THE STICKY ABOUT UNLOCKING AND FOLLOW IT STEP BY STEP!!
Then -- and ONLY then -- will you be able to flash to a custom ROM.
newbie2 said:
So, you start a new thread with the same problem you posted in another thread hoping to get an answer??
Click to expand...
Click to collapse
Yep, I've replied to ecomajor's various posts in various threads and have basically given up. Very little info each time and having a problem that nobody else that has followed the steps has had.
Sorry ecomajor, don't know what else to tell you that hasn't already been said numerous times.
One Last Try -- Then, I Give UP!!
Read the following post on how to flash ANY Wizard (yes, that includes the 8125) --
http://forum.xda-developers.com/showpost.php?p=1177659&postcount=1
Now, follow the directions in that post WORD FOR WORD and STEP BY STEP. The only reason it wouldn't work is that you're NOT READING and/or NOT FOLLOWING THE INSTRUCTIONS STEP BY STEP.
If you CAN'T read and follow directions, then don't be trying to flash different ROMs to your phone. If you're not willing to do what's necessary to help yourself, then noone else is willing to help you, either. . . especially when your problem has already been replied to with the same information over and over in 2 DIFFERENT THREADS now.
Let me detail you the exact steps I have taken. I have read through those posts, many times so I am certain I took those steps
1)device starts normally goto step 3.6 since unsure if unlocked.
2) read farias thread
3) download buttons rom
4)attempt to downgrade rom - failed
4a)tried 1.08 rom instead of button - failed
4b)tried wizard love- failed
5)download lokiwiz
6)followed all directions -failed - since was not able to downgrade rom.
Obviously these directions are not 100% foolproof - I know that the first time I tried installing WM6, I did not read through all the threads and after much effort I discovered that if I installed the official cingular 225 rom then I could get my ppc back working but since then I have had no luck getting flashing to work. Please tell me what I am doing wrong because noone has had my exact situation. there is no need to act all holier than thou and accuse me of not reading because since I screwed up the first time I have read through all these threads numerous times.
Ok, one more thing to try (shot in the dark, but I have no clue what is happening here)...
On your PC (its running XP, right???), do you have Firewall and/or Antivirus? If so, reboot your pc and don't start anything and then turn off your Antivirus and Firewall programs (I found a couple of threads where people were getting the error 260 when ZoneAlarm is active). Now try flashing the button rom. Don't try doing any other roms, don't try doing lokiwiz, just try to get the button rom on. If that works, then continue on with the steps here:
http://forum.xda-developers.com/showthread.php?t=285435
You might even try booting your computer into safemode and try flashing that way (I doubt activesync would be there, so put the phone in bootloader mode, and if you see USB above the left softkey then you should be able to flash it this way from safemode. Never tried it, but it pretty much eliminates anything that may be on your PC thats causing problems).
If none of that works, then get back to an official stock rom again and report back here with exactly what you did, what you saw, and all. Don't worry about the post being long, because to me, too much info is better than just short posts that don't tell us anything. Also, only update this thread. Forget all the other threads you have stuff going on about this problem.
Final question, I asked this before (and I don't remember if you answered or not)... Have you tried to flash your device from another PC?
And I've attached the ROM Update Utility Readme.doc that describes the error messages and how to fix them.
The weird thing is I never get code 260 with the cingular rom update just with the other roms. I will have to try the disabling all firewalls, antivirus etc at home bc at work there is all sorts of stuff i dont want to mess with. Problem if I do it in safemode is then the activesync driver wont be loaded and it will give me an error for that.
mfrazzz said:
Ok, one more thing to try (shot in the dark, but I have no clue what is happening here)...
On your PC (its running XP, right???), do you have Firewall and/or Antivirus? If so, reboot your pc and don't start anything and then turn off your Antivirus and Firewall programs (I found a couple of threads where people were getting the error 260 when ZoneAlarm is active). Now try flashing the button rom. Don't try doing any other roms, don't try doing lokiwiz, just try to get the button rom on. If that works, then continue on with the steps here:
http://forum.xda-developers.com/showthread.php?t=285435
You might even try booting your computer into safemode and try flashing that way (I doubt activesync would be there, so put the phone in bootloader mode, and if you see USB above the left softkey then you should be able to flash it this way from safemode. Never tried it, but it pretty much eliminates anything that may be on your PC thats causing problems).
If none of that works, then get back to an official stock rom again and report back here with exactly what you did, what you saw, and all. Don't worry about the post being long, because to me, too much info is better than just short posts that don't tell us anything. Also, only update this thread. Forget all the other threads you have stuff going on about this problem.
Final question, I asked this before (and I don't remember if you answered or not)... Have you tried to flash your device from another PC?
Click to expand...
Click to collapse
ecomajor said:
The weird thing is I never get code 260 with the cingular rom update just with the other roms. I will have to try the disabling all firewalls, antivirus etc at home bc at work there is all sorts of stuff i dont want to mess with. Problem if I do it in safemode is then the activesync driver wont be loaded and it will give me an error for that.
Click to expand...
Click to collapse
I've never tried it in safemode so I don't know if that will work or not, it was just an idea as we are grasping at straws here. But if you boot to safemode, and with the phone at the bootloader screen (hold down the camera button while you turn it on to get to the "rainbow" bootloader screen), if it shows USB above the left softkey then the computer and phone are communicating and Activesync does not matter. BTW:You can try the safemode way there at work as you will have no network connectivity in safemode so you don't have to worry about violating security policies.
You still have not answered my one question directly... Have you tried flashing the button rom to your phone on multiple computers? Or have you always done it from the same PC? And are the PC(s) that you are using running Windows XP?
What DOC chip does your device have? G3 or G4?
If you have a G4 then i guess you ruined your bootloader since G4 devices don't have and don't accept 1.xx IPL versions!!
I have tried button from multiple pcs. This time it gets up to 98% on button and then dies and it gives error 302 - update error for the button. This is a problem that I was having before.
Did you read the document I posted?? If you're getting Update Error 302, you're not going to be able to recover with anything other than the stock Cingular ROM.
Chances are that you did indeed ruin the bootloader when you tried using the ShellTool to flash a G3 phone. And I doubt seriously that you'll be able to do a warranty exchange if you can run the stock ROM successfully, so I'm afraid you're stuck now with the stock-shipped ROM.
So you are saying there is no way to fix the bootloader (like flashing it or soething) I was figuring I had screwed something up. I actually had read the document before but thanks for your help. Why is it that you can fix many other issues with the 8125 but not the bootloader?
I'm not saying it CAN'T be done. What I AM saying is that in the year I've been registered and active here, I've not seen any posts/threads about recovering from a bad bootloader. But that doesn't mean that there ISN'T a way to do it.
You might want to do a search of the Wizard section for bootloader error or recovering bootloader to see what might come up.
Good Luck!!
ok, I have read all there is to read on this site and on WIKI. What good is it if what I am reading makes no sense to me? I know what .cab files are and how to use them, but what is a .rar file and how do I unrar or unzip it? Do i really need to create files in DOS?
All I want to do is upgrade my BA (sx66/cingular using unlocked on tmobile) to windows mobile 5.0. I know there are way too many threads on here about people who are getting stuck or having certain errors or need help in some way. I can't even get started! The few "step by step" guides I found, start off easy enough an 3 steps into it they referring to things that I have no idea what they are or how to do (yes i have read all the "please read before asking questions" stuff) Again what good does it do if you dont know what you are reading. Maybe its not broken down into simple enough terms for the average joe.
In any event, is there anyone that can shed some light on this stuff for me or aid me in a walk through. Or am I just out of luck because of my lack of software engineering knowledge? Thanks for your time all and I appreciate any feedback. Surely there is someone out there as dumb as I in this area that made it through (or at least I can hope)
You need winrar (www.winrar.com) to "unrar" the files in order to use them.
Winrar works just like winzip but it handle .rar files. So basicly you will download winrar to your computer, install it, then download the rar file with the rom you want to upgrade your device.
Using winrar open the rom archive and extract to a folder on your computer.
Run build.exe, select the options you want for your rom and press the > button.
From there do as the guide says.
spunk32, calm down We are here to help, not kill newbies
Two things:
1. When you don't understand some terms like "unrar" that not PDA-related, just google it. Things like this are considered basic here
2. When you have specific problem about one of the points, post a question (let's keep it in this thread) and smb will try to explain. But try to understand some of us, that we are not going to explain how to copy or download a file
General comment:
ROM upgrading is not totally safe and error-prune. You have to understand fully what are you doing and what for/what is the result. Basic knowledge of the way the PDA works is also good, to make good decisions on the way. That's why I do not consider updating (especially BA from WM2003 to WM5) as a task for everybody (for ex. I think that updating WM5 to WM6 with full unlocking of Hermes is much easier, but still not safe).
I would propose you to use Baniaczek's ROM (instead of XPlode rom cooking set - I looked at the PDF guide - yes, this one is complex, but some of the pictures might be helpful) as there is one step less on the way.
Full guide for you is here (on bottom of the page)
http://wiki.xda-developers.com/index.php?pagename=Helmi
You should go through all the options here, when you update from WM2003. Remeber, that going back to 2003 needs to go through another procedure, that will recreate ExtROM (yes, this is one of the magic words you should understand to play with ROMs).
Thanks for the info guys. ill delve a little deeper and see what happens. im sure ill be back on here with a post when i come to another speed bump. thanks again.
ok, i have gotten this far: downloaded winrar software, downloaded the following ROM-Helmi_BA_WM2k5_AKU3.5_v1.4.CF2.R2. Then I clicked on MaUpgradeUt_noID.exe. When i click continue on the welcome screen, the next screen shows "software converting from....to..." all the data fields are blank. Is this normal and am I on the right path? I did NOT click on upgrade to continue the process b/c I wasnt sure if I had missed something. Thanks again all.
Read what I posted moment ago in "No data from device in MyUpgradeUt" thread. I just checked again screen while updating Xplode on my BA:
In From fields there is only Radio version
In To fields, I have only Ce Image Version: 5.35.05
All other fields are emplty (and not important after all, especially nonexisting ExtROM).
Press your power button, the record button (has a cassette on it) and your reset button at the same time. Wait for the Serial or USB to show on the screen (will be dark) then flash your ROM.
It is in the forums around here somewhere on how to do that but I am to busy to find it for you to post a link.
ok, i think i made a mistake. i got as far as the step where it says you MUST say YES to the first two things on the reboot screen or whatever. all of them said NO, i tried to change it to YES , but i did not know how to change it. i hit the mail button and the screen white and loaded as is. how do i get back to the screen where i need to make the "YES" changes and how do i change NO to YES??
ok, i re-read and saw where i missed how to toggle the YES/NO. so since i was dumb enough to miss that what have i done by not changing the "NO"s to "YES"s? The device seems to be working fine. Is there something that I am not aware of yet?
If you restarted the device and made the hard reset again, this time correctly (selecting proper settings) device should work fine.
You might not noticed, but if you take battery out for while and then start the device, radio won't start (there will be no version next to letter R - means GSM mopdule won't work). You need to make soft reset few secs after first starting of the device to make it run. This is on of not so many problematic things with BA under WM5.
i have not done anything to reset the "yes/no" settings and the device has been working fine all day. i dont ever take off my battery so hopefully i wont have the problem you were refering to.
also, is there any way to remove the camera software since i dont have a camera on my device.
how do i upgrade the radio? i tried WIKI, but i got error messages and when i tried to follow the troubleshooting the links didnt work. outdated i guess.
If you never done correctly hardreset of you BA, you should - you can have a lot of odd problems without hard reset after installing (or upgrading) WM5.
Radio: I followed Wiki and made update radio (1 year ago) from some old version up to 1.13 - without any problems. Follow step after step and port exact error message and on what was happening a this exact moment.
ok, i reset and corrected to NO, YES, YES. thanks. what about removing camera data? any ideas?
You cannot delete apps that are already included in the ROM - this is Read Only Memory, as you know.
When you feel comfortable with flashing and playing with all those files, you will be ready to try xplode kitchen in which you can just select stuff you need to be included in the rom. Manual is a bit longer but still nothing really hard. You can find PDF with full instruction on Wiki pages.
ok i understand what your saying about the camera app. i have tried many times and many versions of the radio upgrade and none work. i have gotten just about every error code there is. am i supposed to be in that "boot" mode when i run it or simple be synced? ill keep looking for a thread that has recent info, but what i see is out of date with links that are no good.
You should follow http://wiki.xda-developers.com/index.php?pagename=BA_Radio_1.15_Upgrade and Second Methord Type I EASY (this is the one I used). Because you have no camera, you device is PH20B1, but AFAIK radio is the same.
You need to put your device in "serial" booloader mode (non backlighted screen, "serial" or "USB" written in lower part of the screen depending on USB cable connected or not (Power+Softreset+Record).
blue tooth wont turn on
the wm5.0 has been working great. the only problem i am having is that the blue tooth wont turn on. i have tried every method of enabling it, but it always shuts itself off. any ideas?
First of all i do not know where to post this. I have had a HTC wizard for over a year now. it has been working fine after cooking up wm6 and installing it for 6 months. today when i restartet the phone pulling the battery out and inserting it, the phone starts up, then the blue screen comes and shows ispl etc, then windows image shows, there it stops. i do not know what to do. It has been a while since i did pocket pc modding now, and i have forgotten all about it.
Alexander, [email protected]
Maybe something crashed the OS software.
Hope you have a system backup, or at least PIM backup using ActiveSync because what you need now is a hard reset.
Punching the reset hole (next to IR window) while holding CommManager+VoiceDial, then press "Dial" as prompted.
how do i hard reset my dash/s620?
i have tried hard reset
i have hard reset the phone. i do not have any backup in active sync. and i dont think that matters. because my phone does not connect to activesync since it does not start up. and in the three colored boot mode the phone is not detected by active sync. when i hard reset the phone it just came to the same point and freezed
If you didn't touch the ROM for long time, then it is probably a hardware failure...
lovemy318 said:
how do i hard reset my dash/s620?
Click to expand...
Click to collapse
READ YOUR PHONE MANUAL, and THIS IS NOT DASH FORUM.
hard to believe
First off, thanks for fast responses.
It cant be hardware(Not as a total theory of course) or likely not, because phone was not touched by water, shock, bumb fire or anything. it laid on my desk, worked, laid on my dask more, freezed. and it has been working for 6 months with wm6. is there anyway i can flash something into it. without activesync, but in the three colored boot mode?
Get into bootloader, plug in your usb cord and give it a minute...ON THE TRI-COLORED SCREEN do you see in the bottom corner "USB"??? If yes, you are OK. Get a stock rom such as the Tmo 2.26 and flash that. If you do not see "USB" in the bottom corner then as far as I know, you are fukd.
For more info on issues, read the linky in my siggy. There is valuable info there that may help with other ways to flash a rom.
Good luck.
i see usb
thanks, guess i am not fked then
Only problem is i have forgotten all about this now, and that i am sorry for.
But i have to ask you, as from norway wich stock rom to choose, what is stock rom, and when you say bootloader, is that an expression for the three colored screen or is that a program, that can flash in three colored screen? Thanks, i do not expect an answer on this noob questions, but i would really apreciate answers.
stock rom & bootloader
stock rom is the rom which comes with ur phone while purchasing it.. u can call it base rom..bootloader is tri-coloured screen which is bios for ppc if it gets fked then phone is bricked..next time if u cant boot up, then u can flash ur phone with the help of bootloader...
that was fast
thanks, but i do not think i have the rom that came with my mobile phone:/
and i do not know how to flash from tri colored screen, because all the files i have tried cant detect my phone.
ipl adn spl are 3.08 if that helps anything.
that was fast
is there an app you use to flash from tri colored
there is no need for any app, just connect ur phone to tri-coloured screen..u willl see usb in down left corner.. then ur phone is connected then run RUU utility.. if any problem comes i am online at hotmail... [email protected]
Can you power down? If not, remove battery for 1 seconds, the re-insert. Then press all at once the camera, comm and power buttons (or I believe you can also press the camera and soft reset. It is in the wiki explaining, as are some stock roms. Use any stock rom if you plan on flashing a cooked rom. The Tmo 2.26 is a decent stock rom, there is a 3.08 on the forum somewhere that you can also use. Get a stock rom. Get into the tri-colored bootloader. Look to see if it says usb in the bottom corner. If yes, connect your cable and using the ruu from the stock rom, flash your phone. Once a stock rom is installed follow the directions to cid/sim unlock your phone. Once unlocked, you can flash any cooked rom.
PS- I am assuming you have a G3 phone.
PPS- reading the wiki and the stickies are very helpful. Give them a try.
im sutch a noob
yeh i got same problem... i will try a hard reset but im at school... hope it fixes it... i got imate jasjam... BETTER WORK OR I WILL KILL MY BROTHER 4 STUFFING AROUND WITH MY PHONE
im sutch a noob
gah... it diddent work what do i do now????
Hello. I'm new in here. half hour ago I got registered. so i have a problem with my HTC. For about 1-2 weeks now the device was restarting. 2 days ago the device never opened again. yesterday I tried the hard reset sequence and the device open to the message that i will lose everything and if i agree to press send but when i press it i get a green screen and nothing more. what can i do? what might be the problem? I uploaded also a video (but I can't post it cause I am a new user so ask me to send it as a pm) and a photo of the green screen.
thank you very much.
By all means, if you don't mind losing data that you had on the ROM memory, then hardreset.
Hard resetting I think is the best possible solution for you.
So press that green phone button when it tells you to ^>^
I already did a hard reset. that's why i have that green screen. I did a hard reset about 4-5 times now. thanks for your answer.
Ah, I see.
Try this:
Soft reset your phone while holding the camera button.
Does this get you to a screen where it's Red/Blue/Green/White Screen?
If it does, try plugging in a USB cord. If you get this far and see the word 'USB' in the lower left hand corner, then I think we can continue on.
I did it and it shows usb. what next?
Awesome, I'm glad.
Next, Download and run the .exe:
http://rapidshare.com/#!download|16..._4.17.405.2_4.1.13.44_02.94.90_Ship.exe|56629
After this, all should be well.
Now if you want to flash custom ROMs like the ones that I make, just follow the directions on any one of my ROM threads from Top to Bottom ^>^
before i continue. after the installation i will have the OS back? I will have to install it again? i had WM6. thank you very very much for all the help.
error 300: INVALID UPDATE TOOL.
THIS UPDATE UTILLITY CANNOT BE USED FOR YOUR PDA PHONE. PLEASE GET NEWER UPDATE UTILITY.
that's the message i got.
Hmm, okay, try searching mediafire for the user aizend1985 and look for an .exe entiled Wing something or another.. I'm out right now, so cant get the link for you.
Download and run.
i can't find the user. i'll try again. when you have the time please send me. again thankl you very much. have a great time.
Here you go mate, try this:
http://download1152.mediafire.com/he785npun6pg/yj1oz2m3mzm/TMo_Wing_RUU_Update_4.26.531.4.exe
If this doesn't work I'll try to do some research for you and see what we can do.
Error 244: Invalid model id.
Okay. The last thing you can do is to try the dutch vodaphone herald version:
http://rapidshare.com/#!download|18..._4.21.172.1_4.1.13.44_02.94.90_Ship.rar|52629
Download and run the .exe from the Red/Blue/Green/White screen.
If this loads onto your device, then what we do is we HardSPL next.
*crosses my fingers for ya*
If this doesn't work, then have HTC try to repair it. Because I don't think there is anything else to do for it :1
:'( Error 244: Invalid model id.
thank you very much for everything. at least I know that it can be fixed.
you reflashed your phone in some custom roms?
but it didnt work still and you tried the hard spl too.... can you tell me the history of your phone before it went like that, i am a technician and might help you on your problem.... what was the last thing you did on your phone? i will wait for your reply if it's ok....
dear [email protected]
I have the HTC P-4350 for the last 5 years. the last 1-2 weeks the phone started to freeze and the screen went white slowly and then restart. after the 2 weeks the phone closed and didn't open again but the hard reset is working until the part that said format done (or something like that) and then i get a green screen (see the photo I have attached here). after that i made this post and the friend Tribulattifather (member of the site here) helped me with some info and gave me some files to try and install but the first file gave me this message
"error 300: INVALID UPDATE TOOL.
THIS UPDATE UTILLITY CANNOT BE USED FOR YOUR PDA PHONE. PLEASE GET NEWER UPDATE UTILITY."
and the other gave me
"Error 244: Invalid model id.".
there isn't something else. any idea?
thank you.
what is your spl number and ipl....
did you do the HARDSPL on your phone????
do the hardspl first and then flash your phone using a micro sd....
tell me if you already did that.... i will wait for your reply....
i also want to know if you dropped it or something before it went like that.... plz tell me the whole history of your phone....
to my perspective, the phone's problem can be resolve in flashing....
tell me if you hardspl it,,,, because you cant flash it on some ROMS if it's not HARDSPLed...
hi [email protected] i had a problem with my internet that's way I answer now after all that time. I droped it a couple of times by accident but that is a long time ago. the IPL is 4.17.0001 ans SPL 4.17.0000. i never did anything like hardspl. i changed the flex cable 5 months ago. when i first got the phone 5 years ago it had WM5 and after 5 months when i bought it I got WM6 at service. i never got the phone to service cause never anything happen. i can't remember anything else know.
I have an update for my device. now it doesn't open with anything. i mean i can open it to hard reset or to see the spl. it doesn't respont to anything.
May be time to put the phone to rest, mate u.u
I'll play the taps..