Hello Ladies and Gents,
Does anyone know how/where to insert the strap in the MDA Compact IV?
I usually use a wrist strap on my devices so I can put it on my wrist while I'm using my phone in-case it slips and falls over the balcony or on the floor when I'm smoking with the other hand.
D8LOM said:
Hello Ladies and Gents,
Does anyone know how/where to insert the strap in the MDA Compact IV?
I usually use a wrist strap on my devices so I can put it on my wrist while I'm using my phone in-case it slips and falls over the balcony or on the floor when I'm smoking with the other hand.
Click to expand...
Click to collapse
It's very simple. Remove the back cover; at the bottom (with the screen facing down) to the right of the mini-usb port you have a small hole. That's not the microphone. The microphone is the smaller, rounder hole to the left of the mini-usb port. If you insert the lanyard (or thin strap) into the orifice to the right handside, it'll come out on the small slit inside the back cover. Hook the lanyard onto the slit and replace the back cover.
Thanks but the strap I've got does not go through that hole, I'm going to have to buy another wrist strap.
aiwama said:
It's very simple. Remove the back cover; at the bottom (with the screen facing down) to the right of the mini-usb port you have a small hole. That's not the microphone. The microphone is the smaller, rounder hole to the left of the mini-usb port. If you insert the lanyard (or thin strap) into the orifice to the right handside, it'll come out on the small slit inside the back cover. Hook the lanyard onto the slit and replace the back cover. You can also see page 30 of the "Getting Started" pdf booklet.
Click to expand...
Click to collapse
That leads me to my second question...
Does anyone know of a good wrist strap?
http://forum.xda-developers.com/showthread.php?t=475528
I use one for a Wii controller, hehe, its kind of nice, but I wish it was black instead of white
Related
Got out of the truck this morning and heard a clink and saw my stylus had fallen to the ground. I picked it up and noticed its not staying in anymore. Used to be some kind of friction holding it in, but now any movement and the stylus starts to slide out.
Before I try tape, has anyone had this before? I've checked one other mogul and I don't see anything missing, but did narrow it to my phone chassis.
Same Here
I got the same prob. So i put a piece of electrical tape on the end of the stylus, Not the point part the other part. Just put a little square on it.
It fit by actually being a fraction bigger than the hole u just shoved it up to hold it but after a while of putting the stylus in and out the heat will eventually morph it making it a bit smaller sliding it out and the cap well that basically just kept it up! My sister actually bit hers off i would try addidng something to the tip of the stylus like elctrical tape as stated above.
I used to have a hell of a time keeping stylii in my 6700. The eventual cure for the 6700 was to bend the stylus ever so slightly. Have you tried that?
Stylus fix..
Hey every-1 had the same problem till i stuck a piece of paper inside slot so when stylus goes in it gives it a tighter squeeze..but if you take off battery cover you should be able to see where the looseness is coming from...
Why not buy a third-party stylus replacement (found quite a few that fit the Mogul) that also have a pen?
Do a google search. Seidio offers one just not in 3-packs.
Yea this funny might be the ultimate noob question, but...
I bought my phone used and I have no idea how to remove the battery door and I dont want to just pry it open.
Is there a specific wat to do this?
Please answer I want to try my new battery!
THANKS!
Throw it at the floor!
Slide the back down. Simple as that.
Push the back cover (gently) in & up. The whole back cover slides up a little bit, then it simply comes off.
I'm sure AT&T has manuals & other documentation available.
http://www.google.com/search?hl=en&q=at%26t+tilt+user+manual&btnG=Google+Search
thanks! that was simple.
It takes a small amount of force. Don't worry if you break it, they're only like $13 on ebay.
cbass said:
Throw it at the floor!
Slide the back down. Simple as that.
Click to expand...
Click to collapse
Shouldn't that be slide the back up
Seriously though, hold the phone screen down in the palm of your hand and grip it with the top pointing away from your body. Then place your other hand flat on the back cover and push up - as in away from your body - and it should slide about 2mm and come loose.
Be careful though as there are small tabs all around that 'lock' the cover in place and they are a bit fragile. I have lost the one near where the stylus head is and its now ever so slightly 'floppy' in this corner...
HTH
Andy
hold the device naturally in portrait orientation with the screen facing you...
now turn it over so that the screen faces the floor...
holding the device in both hands, place your right thumb just under the external speaker grill and place your left thumb just under the gps external antena slot...
press your thumbs into the back cover a bit and push upwards (towards the top of the device)...
it should click open
Hi all,
Not quite sure how to explain this. When the Diamond was new the styles 'sprung' back into place with its magnet. Now, I have to push it in - it defaintely has some resistance. I've taken the back off and cleaned it but no change.
Anyone else got/had this?
Rich
the magnet beside the battery has probably gotten unstuck.
several ppl have had this same prob; I was the first, I believe.
just need to get a tweazer and some glue to hold the magnet in place.
i thought it is the stylus that is magnetic not the pda itself?
Hi,
Thanks for that - I can see a magnet on the side of the batt (cirlced in the pic below) but it *appears* to be ok. Does it look fine - or has it moved - or has something dropped off???
Rich
ok ok - fixed it. The magnet had come out of its whole and stuck to the side of the battery. By replacing it all is ok now. Thankfully I did not lose the magnet!!!
Pic attached
Well done...
Might have something to add here
http://forum.xda-developers.com/showthread.php?t=422574
LOL !!!
rakh1 said:
ok ok - fixed it. The magnet had come out of its whole and stuck to the side of the battery. By replacing it all is ok now. Thankfully I did not lose the magnet!!!
Pic attached
Click to expand...
Click to collapse
Excelent spot mine was in the exact same spot, Thanks for sharing
The stylus is the magnet not the pin inside die Diamond!!!
Try to hold your stylus against some metal...
horstborsch is right. the stylus is the magnet.
the stylus attracts other metallic objects, not the phone.
what we see in the image probably is the switch that detects the magnet
I have tried to fiddle around with the stylus and the phone, in order to solve this little "mystery" and I think that they are magnets both in the phone and the stylus.
This will make the stylus lock in place. The phone has a magnet where the north is up, then the stylus will have a magnet where south is up (magnets are in opposite directions). Therefore it will lock inside the phone, as the south pole of the phone's magnet will attract the north pole of the stylus, and the opposite for the other poles.
If the stylus won't lock properly in place, one reason could be that the magnic field of the stylus has been disturbed or changed.
Fx when you place the stylus on top of a speaker or any electrical component having a magnetic field.
However if it is a good magnet this shouldn't affect it, but you never know..
The stylus can be completly demagnetised if you pass it through a solenoid, but I don't think anyone tried that yet with the stylus
I'm not saying that I'm right, but at least it could be one solution
Cheers!
Hey guys, I have also just found a little magnet. But I have the MDA Compact 4. Could anyone point out where I need to put this magnet back?
I have tried putting it in various places but it does not work.
Thanks guys.
Nuke79 said:
horstborsch is right. the stylus is the magnet.
the stylus attracts other metallic objects, not the phone.
what we see in the image probably is the switch that detects the magnet
Click to expand...
Click to collapse
Hahaha,what did you mean for switch that detects the magnet?
didnt you learn at school that two magnets attract each other.
anyway i had the same problem and found the small magnet on my battery.
...it has the size of 2mm x 12mm so you can easily find the empty place where to put it..
The screen on my Rogers HTC Raider is scratched. It is deep enough that I cannot remove by applying polisher. Screen still works but I rather replace the screen as the scratch is visible.
Where can I purchase the screen and replace it myself?
http://www.tmart.com/Replacement-LCD-Display-Screen-for-HTC-G19-Raider-4G_p137438.html
http://www.repairsuniverse.com/htc-vivid-screen-replacements-repair-parts.html
..
Thank you.
tap the thanks button
and good luck
A little advice - I've already replaced the screen on my Raider
Hi, glad someone else is attempting this. I had never replaced a screen in a phone before trying this so for me it was a little hair raising the first time I took it apart. On the back of the phone under the battery cover are 5 screws you need to remove, and one little plastic cover. Under the cover is the connector from the mainboard. Its just a little pop out connection, gently lever it loose before removing the shell to avoid hurting the ribbon.
Once you get this far, flip the phone face-up, and *from the bottom*, gently lever the sides and bottom of the plastic shell away from the screen. Its relatively easy.
Continue working along the edges toward the top until the plastic shell pops free, after that put it face-down again and remove the screws holding the battery holder to the rest of the phone. Pull it up and out to the left to remove it, being careful not to bend the battery contacts as they stay with the rest of the phone. Keep the screws with it, trust me - its easier to remember what goes where this way.
Once you have the battery holder off, put it aside and remove the screws holding the mainboard(s) to the shell. Also you will find three wires with little cup contacts at the ends, gently detach these as well, and when the screws and wires are off, carefully remove the boards. Look closely at the plastic tabs holding them in and you'll see how they come out. When taking them out of the phone you'll need to lift them like you were opening a book - ie. folding them to the right. Underneath are two sockets with ribbon cable connections, one should already be detached - the other can be popped off at this point. If you skipped detaching it at the beginning, now's the time to remove both.
This should leave you with two free boards attached in the middle by a black ribbon. Put them aside and what you have left in your hand is the metal shell, LCD, and digitizer.
NOW..the crappy news. This wonderful, beautiful, powerful, ESPENSIVE phone, is held together by black double-sided tape. Yep. Tape. AND you'll need some more before installing the new digitizer. I ordered mine from tmart as well and it not only comes with the wrong screwdrivers (btw you need a #1 philips bit - VERY tiny!!) but it doesn't come with any adhesive to mount the screen to.
Your new screen should also come with some prying tools, and they are quite handy. The guitar pick one didn't do much but the lever is very handy. You'll need to gently pry the digitizer away from the LCD with this tool being careful not to put too much pressure on the lcd or it might snap. Its only a few mm thick. GO SLOW.. you should have no problems. I've done it a few times now - I'm kinda rough on my toys.
Once you have the part un-taped, its still got the ribbon cable going back behind the lcd. Its connected to a small, thin socket on ther board. You lift a small white lever (remove the tape and save it - reapply it to the new connection) and slide the cable out. You'll need to use your lever again and pry up the lcd enough to slide the ribbon out from behind it. This can be tricky. Again, go slow, be real cautious..the tape is pretty strong. Once you have the panel out completely its just a matter of reversing the process. If you're real careful when removing the original panel, you might be able to reuse the double-sided tape thats in there.. I wasn't so lucky. Mine was covered in glass shards, as I mashed my screen pretty good.
Hope this helps!! I had a rough time the first time, but now its easy for me. I like taking it apart lol..
Let me know how you do! Good luck!
Brian
Hey guys,
I just swapped my silver one to a black shell.
Very simple change over for the most part.
Prior to snapping the back cover on, I made sure to test all functions. They all passed fine. I then snapped on the back and rebooted the phone. The lower speaker no longer played any audio, instead just clicks until the sound finishes. It's incredibly annoying during speaker phone calls. Any idea what it could be, or better yet, is there an app that can force the phone into mono mode with only the top speaker working?
Hey guys,
I just swapped my silver one to a black shell.
Very simple change over for the most part.
Prior to snapping the back cover on, I made sure to test all functions. They all passed fine. I then snapped on the back and rebooted the phone. The lower speaker no longer played any audio, instead just clicks until the sound finishes. It's incredibly annoying during speaker phone calls. Any idea what it could be, or better yet, is there an app that can force the phone into mono mode with only the top speaker working?[/QUOTE]
Alright, took it apart again and inspected it. Found the problem. at the base of the phone there is a ground clip that covers and grounds the usb board to the main board. Directly above that there is a very small connector with a black and red wire in it, those are your lower speaker connector. when reinserting it into the back cover the red wire moved onto the ground plate and wormed its way between it and a spring clip that ground it to the back cover.This spring clip applied enough force to lightly cut the casing thus grounding the positive speaker feed to the phone case. Kinda a b!tch to fix, full disassemble is needed to pull that board out, i then used liquid electrical tape on the damaged spot. Let it dry and reassembled. Now its black and perfect!
I attached a photo of the red wire and its location. Be careful with this area, I was lucky the board or phone didn't short out!
View attachment 2559853
How did you even get it apart??
Iz3man said:
Hey guys,
I just swapped my silver one to a black shell.
Very simple change over for the most part.
Prior to snapping the back cover on, I made sure to test all functions. They all passed fine. I then snapped on the back and rebooted the phone. The lower speaker no longer played any audio, instead just clicks until the sound finishes. It's incredibly annoying during speaker phone calls. Any idea what it could be, or better yet, is there an app that can force the phone into mono mode with only the top speaker working?
Click to expand...
Click to collapse
Alright, took it apart again and inspected it. Found the problem. at the base of the phone there is a ground clip that covers and grounds the usb board to the main board. Directly above that there is a very small connector with a black and red wire in it, those are your lower speaker connector. when reinserting it into the back cover the red wire moved onto the ground plate and wormed its way between it and a spring clip that ground it to the back cover.This spring clip applied enough force to lightly cut the casing thus grounding the positive speaker feed to the phone case. Kinda a b!tch to fix, full disassemble is needed to pull that board out, i then used liquid electrical tape on the damaged spot. Let it dry and reassembled. Now its black and perfect!
I attached a photo of the red wire and its location. Be careful with this area, I was lucky the board or phone didn't short out!
View attachment 2559853
Wow, you've got some courage man! I really want to convert mine to black, but I'm scared.. Never opened a phone before. Post some pics of the phone please.. Any gaps/other issues?
Sent from my iPod touch using Tapatalk
SaHiLzZ said:
How did you even get it apart??
Click to expand...
Click to collapse
Carefully and with a bit of swearing. The back cover is actually dead simple to take off, if it wasn't for the damned adhesive on the sides. Be prepared to need a new rear cover.
I used 3 different thickness guitar picks and a plastic pry tool ( those blue guys you get when you buy any part out of china). I would recommend heating up the sides to start, if you have a bean bag heating pad, use it, put it in the microwave for 2 mins and sit it on the sim card side of the phone. Because the plastic is a little flexible, I was able to slip a pick between the screen and the sim slot, then pry it upwards and slowly slide the pick toward the bottom of the phone. Once you get a little ways down stop and leave the pick in, take a thicker one and to the same, replacing the first with the new one. Repeat with another, the trick is to apply light bust constant pressure on the glue to break the bond. After a few mins of that and possibly reheating, you should be able to go around the corner and across the bottom. The glue is only of the sides. There are 4 clips of each side and 2 on both the top and bottom.
Make sure that the top assembly comes out from the bottom of the phone first or you risk damaging the power button/ir blaster.
I bought a full screen replacement with back cover from etrade, I also bought an empty shell from eBay, I used the etrade parts, but I'll swap the original screen to the ebay parts tomorrow.
Wow, you've got some courage man! I really want to convert mine to black, but I'm scared.. Never opened a phone before. Post some pics of the phone please.. Any gaps/other issues?
Click to expand...
Click to collapse
I was too, I watched videos, I read the forums. In the end I just grabbed it and tried to see If I could even fit the first pick in, then I got farther and finally got it off. The guts are simple to change over, just be aware that the screws are not interchangeable, so take a piece of paper make notes and keep track of your screws. When I got it rebuilt I was bumbed out at the speaker, but because there is no glue on the new free I was able to get the back off in less then a minute.
I see no gaps or problems. Everything works and the phone looks great, in my opinion they should have never made a white and silver. I'll post some picks when I'm back home tonight.
I followed the videos from Go Cell Phone Repair, he has 2, one is the tear down the other is the reassembly, Google YouTube for them, he was very thorough.