The screen on my Rogers HTC Raider is scratched. It is deep enough that I cannot remove by applying polisher. Screen still works but I rather replace the screen as the scratch is visible.
Where can I purchase the screen and replace it myself?
http://www.tmart.com/Replacement-LCD-Display-Screen-for-HTC-G19-Raider-4G_p137438.html
http://www.repairsuniverse.com/htc-vivid-screen-replacements-repair-parts.html
..
Thank you.
tap the thanks button
and good luck
A little advice - I've already replaced the screen on my Raider
Hi, glad someone else is attempting this. I had never replaced a screen in a phone before trying this so for me it was a little hair raising the first time I took it apart. On the back of the phone under the battery cover are 5 screws you need to remove, and one little plastic cover. Under the cover is the connector from the mainboard. Its just a little pop out connection, gently lever it loose before removing the shell to avoid hurting the ribbon.
Once you get this far, flip the phone face-up, and *from the bottom*, gently lever the sides and bottom of the plastic shell away from the screen. Its relatively easy.
Continue working along the edges toward the top until the plastic shell pops free, after that put it face-down again and remove the screws holding the battery holder to the rest of the phone. Pull it up and out to the left to remove it, being careful not to bend the battery contacts as they stay with the rest of the phone. Keep the screws with it, trust me - its easier to remember what goes where this way.
Once you have the battery holder off, put it aside and remove the screws holding the mainboard(s) to the shell. Also you will find three wires with little cup contacts at the ends, gently detach these as well, and when the screws and wires are off, carefully remove the boards. Look closely at the plastic tabs holding them in and you'll see how they come out. When taking them out of the phone you'll need to lift them like you were opening a book - ie. folding them to the right. Underneath are two sockets with ribbon cable connections, one should already be detached - the other can be popped off at this point. If you skipped detaching it at the beginning, now's the time to remove both.
This should leave you with two free boards attached in the middle by a black ribbon. Put them aside and what you have left in your hand is the metal shell, LCD, and digitizer.
NOW..the crappy news. This wonderful, beautiful, powerful, ESPENSIVE phone, is held together by black double-sided tape. Yep. Tape. AND you'll need some more before installing the new digitizer. I ordered mine from tmart as well and it not only comes with the wrong screwdrivers (btw you need a #1 philips bit - VERY tiny!!) but it doesn't come with any adhesive to mount the screen to.
Your new screen should also come with some prying tools, and they are quite handy. The guitar pick one didn't do much but the lever is very handy. You'll need to gently pry the digitizer away from the LCD with this tool being careful not to put too much pressure on the lcd or it might snap. Its only a few mm thick. GO SLOW.. you should have no problems. I've done it a few times now - I'm kinda rough on my toys.
Once you have the part un-taped, its still got the ribbon cable going back behind the lcd. Its connected to a small, thin socket on ther board. You lift a small white lever (remove the tape and save it - reapply it to the new connection) and slide the cable out. You'll need to use your lever again and pry up the lcd enough to slide the ribbon out from behind it. This can be tricky. Again, go slow, be real cautious..the tape is pretty strong. Once you have the panel out completely its just a matter of reversing the process. If you're real careful when removing the original panel, you might be able to reuse the double-sided tape thats in there.. I wasn't so lucky. Mine was covered in glass shards, as I mashed my screen pretty good.
Hope this helps!! I had a rough time the first time, but now its easy for me. I like taking it apart lol..
Let me know how you do! Good luck!
Brian
Related
I bought a replacement digitizer off ebay and they have sent me the generation 1 version.
Before I go and buy the right one can anyone tell me how easy it is to solder the correct one and also if anyone needs a generation 1 version I have a new one here and would be happy to sell it on.
Thanks
its a ***** to do, i just replaced one on my dads xda2, but its the same as the xda2i
after taking a long time to carfuly remove the original without damaging the lcd, i used a safty blade and slid it between the buggered digitizer ad its plastic mount, be VERY carful as u need to apply force and its easy to slip, as i first did and sliced a 2" gash into my thumb... not good. second time i was alot more carful. by putting the screen edge down on a table top and wiggling the blade down all 4 sides, be carful not to cut the lcd ribbon!
i had to cut the 2 side tabs on the touch screens ribbon down by 3-4mm and then seperate all 4 leads, this is due to the design of the gen 2 screen i just followed the way it was originaly soldered on.
you also have to have a low wattage or cool soldering iron, around 10-15watt as it is very easy to damage the contacts i heated the solder on the lcd side and pressed the digitizers ribbon onto it with a small amount of flux, then used a flat screwdriver to quickly cool it down the area, you also have to put slips of paper between the 2 sides leads and the center 2, as it will short out, this was also done originaly.
sounds hard to do but its easy with a little patience, and soldering skills.
i bought it from ebay as well
p.s. do not glue the new digitizer with superglue as you will damage the screen, i just placed it back in the case without sticking it in, been fine for the last few weeks but a few VERY thing strips of double sided tape will do or if your lucky some of the origial sticky stuff will be left over.
does this "digitiser" thing is the faulty part which causing the PDA screen to have so-called Dead area ?
or "missing area"
because I won O2 XDA IIi which can't create straight line at the bottom of the screen.
where and is there any tutorial on how to replace such thing ?
Cheers.
So last week I cracked the glass on my poor Nexus. It took a horrible drop. Well I can't afford another Nexus and I can imagine having any other phone so I figured I'd repair this one. Read up alot on it and watched a video on Youtube. Ordered all the parts I needed I tackled it today.
Well I decided to do a How-To for any other Nexus owner with broken screens.
New digitizer - $40
Torx screwdriver -$5
Philips screwdriver -$5
Plastic tools - Free
Total - $50
Sure beats the $125 some online sites charge.
I would like to thank ifixit and slickromeo.
1. Gather all your tools and replacement glass (known as a digitizer).
Note: Needed tools are a Philips #00, a Torx T4, and a plastic pry tool (Mine was included with the new screen)
2. Set up a clean comfortable area to work in. You may be here for awhile and you're going to want to reduce the amount of dust that could potentially get on the new glass.
Note: I used a folded over microfiber towel to keep the area clean and also add some padding to the hard counter top to prevent even more damage while working with the phone.
3. Power phone off and remove battery cover, battery, SIM card, and Micro SD card. Set aside in a safe place.
4.Our first obstacle is going to be the antennae cover at the bottom of the phone. There are three plastic clips holding it in place (Circled in red). Use a combination of the pry tool, a guitar pick, butter knife, and any other instrument you need to shove in there. It is a pain in the ass... the video I watched online made it seem like it was going to be alot harder than it was, but if you work from left to right, or right to left, and get the outside one unclipped the other two come off pretty easy. Once you get it off set it aside with the battery cover and other things.
Note: Be careful not to break these tiny, fragile clips as they are the only things holding this cover in place.
5. Scream profanities and wipe the sweat off your brow from the previous step. I know it was frustrating and nerve racking trying not to break your precious Nexus.
6. Ok good job now to start the real deconstruction. I'm going to start with the battery tray and then move down to the antennae. There are three screws holding the tray down, but before we start on those there is this tiny ridiculous little "VOID" sticker covering up one of them. I wasn't able to remove it intake, partly because I don't really care about my warranty, but I'm sure with alot of patience and tweezers one could take it off intake and put it back. But screw that just get it off to get to the screw underneath.
7. Now two of these screws is a Torx and the third is a Philips (All in green). Remove them and put them somewhere very safe.
Note: I have four plastic cups set up to place my screws into. These are going into the first one.
8.Next you need to remove the battery tray. There are seven tabs (yellow circles) around it that you need to release using your plastic pry tool. Once those are released gently pull away form the bottom of the phone to remove the tray. Set the tray aside.
9. Now for the antennae cover. There are two more screws to remove, a Torx and a Philips (Orange circles). These screws are going in the second bowl. After the screws are out, gently lift up on the bottom of that cover and it should remove easily. Be very careful not to damage the circuit board during removal.
10. Next to come out is the logic board. there are two more very tiny screws to remove (White circles). Into the third bowl with those. Next you need to disconnect three connections (purple circles). Then carefully go around the perimeter of it with your pry tool and VERY CAREFULLY remove all the little tabs holding it in place. Then simply push up form the bottom of the logic board and slide it out. Set it somewhere very safe.
11. Now onto the actual case of the Nexus. Remove the six Philips screws, 1 at the top and 5 at the bottom . Again there are a series of little clips, five of em, around the perimeter that need to be undone and then the case very easily separates from the screen. Set the case aside.
12. Very simply pry the LCD screen away form the glass digitizer. There it is... the broken glass.
13. Now take your pry tool and from the back of the glass (not the side you would touch if you were using the phone) wedge it between the frame and the glass to separate to adhesive. Once the pry tool is in you can just slide it around the edge of the glass to separate the whole thing. TA-DA your broken glass is forever gone.
Note: The glass is broken and very sharp. Take extreme caution not to cut yourself.
14. Now we just have to put the whole thing back together. Start with the new glass/digitizer. Peel off the plastic protector to expose the adhesive and very carefully put it in place.
15. Wrap the connector that is part of the digitizer around and secure it in place with its adhesive.
16. Take the whole screen assembly and slide it back into the case. Push to secure the clips then replace the six screws that you removed.
17. Slide the logic board carefully back into place. You may have to hold down/more out of the way a few of the connectors. Take it a little at a time and see where it is getting caught up. You got this far don't lose your patience.
18. Snap the back antennae cover back in and replace its screws.
19. Slide the battery tray into place and replace its screws.
20. Snap the gray antennae cover back on.
21. Replace Micro SD card, battery, and battery cover.
22. Enjoy the beauty of your Nexus without a broken screen.
23. Place Nexus in Otterbox Defender case so this never happens again.
I have pictures that document each step but need to be approved by a moderator before it lets me post em... sorry guys
Hey, awesome job on fixing your screen. I would love to see them, my Nexus just went through the same thing 30 min ago. I had it on my lap, and upon stepping out of the car, SMACK, is all I heard. It landed face down and this is the aftermath. It's much worse than it looks in the picture.
Man, that sucks. I know that feeling.
I'll try to put the pictures up to help you out. Or at least a link to my photobucket.
Sent from my Nexus One using Tapatalk
thanks! I just cracked mine yesterday after the phone fell out of my pocket onto a concrete floor. Ouch. I'm giving this a whirl.
Nice, I'll keep this in mind for the day I accidentally break my n1.
I just wish we could somehow jury-rig the Incredible digitizer to our phones =/
I just recently converted to the n1, bought the phone for cheap off craigslists, but notice burn in on the screen, will changing the digitizier also fix the burn in?
Thank you so much for taking the time to do this write up. I just dropped my phone and smashed the screen on concrete 30 mins ago. All is working but the glass is cracked. I've ordered a new Digitizer/Glass from ebay for £30, I just hope it comes by tomorrow.
you can post picture after 5 posts so it should be good now you have 8 posts
I've just completed the work of replacing the broken glass.
I used your guide throughout, it's a shame you haven't been able to post the pictures as it definitely would have helped. I managed to google some dismantling pictures to help with your talk through as it was hard going some times.
Many thanks again.
Another useful tip: run an air purifier aimed at your work station to minimize the risk of getting dust in the glass.
blueboymj: Any chance you can edit your original post and add your pictures so others can use them? I searched quite a lot for a specific procedure to change the digitizer on my poor N1; This was the best, most accurate guide I found. I've done digitizers on a few iPhones (sorry for the profanity) using the ifixit guides, but alas, the ifixit guides were better for them than they are for the N1.
On a side note: The end cap that gives people so much trouble fell off of my N1 in the initial drop. I pushed it back on, and continued using the phone even though the glass was shattered. Removing it the first time was not so hard, I think it was not back on as well as it should have been. Removing it the second time (another story) was much harder. There are two little plastic "bars" on the end cap (step 4 above) that fit into small grooves on the "antenna cover". (step 7) I think the trick may be to possibly pinch the edges of the end cap, while sliding it toward the bottom of the phone. I looked at it after it was open, to see why it was so hard to remove, and realized I had been inadvertently helping it hold itself closed while trying to pry it open. Maybe one of the videos addresses this; I did not watch them.
Thank you to the OP and the responders for this post!
So where exactly did u order the new digitizier and parts from?
Sent from my Nexus One using XDA App
This thread should be added to the N1 wiki. Thanks for the instructions.
DrewOntheMYT said:
I just recently converted to the n1, bought the phone for cheap off craigslists, but notice burn in on the screen, will changing the digitizier also fix the burn in?
Click to expand...
Click to collapse
Burn in? Like shadowing on the LCD? Nope.
Thats the LCD, and is completely different than the digitizer. The digitizer is just a clear plastic/glass layer that goes OVER the lcd to detect touch.
I had the digitizer and a new case and was going to have a local phone store replace this for me. However, they just gave me some BS story about how you cannot replace the digitizer without also replacing the LCD screen, which I did not provide.
So I've been without a phone (since they have it) for no reason and have to drive out of my way to retrieve it.
Hey crappy phone store, if you're too scared to do the job just say so, don't try to make up a bunch of manure and say it can't be done.
Anyway, I just ordered the required tools that I don't have and am going to give this a whirl.
OP, if you can't post your pics, can you email them to me?
does it fix the multitouch problem?
Hey guys,
I just swapped my silver one to a black shell.
Very simple change over for the most part.
Prior to snapping the back cover on, I made sure to test all functions. They all passed fine. I then snapped on the back and rebooted the phone. The lower speaker no longer played any audio, instead just clicks until the sound finishes. It's incredibly annoying during speaker phone calls. Any idea what it could be, or better yet, is there an app that can force the phone into mono mode with only the top speaker working?
Hey guys,
I just swapped my silver one to a black shell.
Very simple change over for the most part.
Prior to snapping the back cover on, I made sure to test all functions. They all passed fine. I then snapped on the back and rebooted the phone. The lower speaker no longer played any audio, instead just clicks until the sound finishes. It's incredibly annoying during speaker phone calls. Any idea what it could be, or better yet, is there an app that can force the phone into mono mode with only the top speaker working?[/QUOTE]
Alright, took it apart again and inspected it. Found the problem. at the base of the phone there is a ground clip that covers and grounds the usb board to the main board. Directly above that there is a very small connector with a black and red wire in it, those are your lower speaker connector. when reinserting it into the back cover the red wire moved onto the ground plate and wormed its way between it and a spring clip that ground it to the back cover.This spring clip applied enough force to lightly cut the casing thus grounding the positive speaker feed to the phone case. Kinda a b!tch to fix, full disassemble is needed to pull that board out, i then used liquid electrical tape on the damaged spot. Let it dry and reassembled. Now its black and perfect!
I attached a photo of the red wire and its location. Be careful with this area, I was lucky the board or phone didn't short out!
View attachment 2559853
How did you even get it apart??
Iz3man said:
Hey guys,
I just swapped my silver one to a black shell.
Very simple change over for the most part.
Prior to snapping the back cover on, I made sure to test all functions. They all passed fine. I then snapped on the back and rebooted the phone. The lower speaker no longer played any audio, instead just clicks until the sound finishes. It's incredibly annoying during speaker phone calls. Any idea what it could be, or better yet, is there an app that can force the phone into mono mode with only the top speaker working?
Click to expand...
Click to collapse
Alright, took it apart again and inspected it. Found the problem. at the base of the phone there is a ground clip that covers and grounds the usb board to the main board. Directly above that there is a very small connector with a black and red wire in it, those are your lower speaker connector. when reinserting it into the back cover the red wire moved onto the ground plate and wormed its way between it and a spring clip that ground it to the back cover.This spring clip applied enough force to lightly cut the casing thus grounding the positive speaker feed to the phone case. Kinda a b!tch to fix, full disassemble is needed to pull that board out, i then used liquid electrical tape on the damaged spot. Let it dry and reassembled. Now its black and perfect!
I attached a photo of the red wire and its location. Be careful with this area, I was lucky the board or phone didn't short out!
View attachment 2559853
Wow, you've got some courage man! I really want to convert mine to black, but I'm scared.. Never opened a phone before. Post some pics of the phone please.. Any gaps/other issues?
Sent from my iPod touch using Tapatalk
SaHiLzZ said:
How did you even get it apart??
Click to expand...
Click to collapse
Carefully and with a bit of swearing. The back cover is actually dead simple to take off, if it wasn't for the damned adhesive on the sides. Be prepared to need a new rear cover.
I used 3 different thickness guitar picks and a plastic pry tool ( those blue guys you get when you buy any part out of china). I would recommend heating up the sides to start, if you have a bean bag heating pad, use it, put it in the microwave for 2 mins and sit it on the sim card side of the phone. Because the plastic is a little flexible, I was able to slip a pick between the screen and the sim slot, then pry it upwards and slowly slide the pick toward the bottom of the phone. Once you get a little ways down stop and leave the pick in, take a thicker one and to the same, replacing the first with the new one. Repeat with another, the trick is to apply light bust constant pressure on the glue to break the bond. After a few mins of that and possibly reheating, you should be able to go around the corner and across the bottom. The glue is only of the sides. There are 4 clips of each side and 2 on both the top and bottom.
Make sure that the top assembly comes out from the bottom of the phone first or you risk damaging the power button/ir blaster.
I bought a full screen replacement with back cover from etrade, I also bought an empty shell from eBay, I used the etrade parts, but I'll swap the original screen to the ebay parts tomorrow.
Wow, you've got some courage man! I really want to convert mine to black, but I'm scared.. Never opened a phone before. Post some pics of the phone please.. Any gaps/other issues?
Click to expand...
Click to collapse
I was too, I watched videos, I read the forums. In the end I just grabbed it and tried to see If I could even fit the first pick in, then I got farther and finally got it off. The guts are simple to change over, just be aware that the screws are not interchangeable, so take a piece of paper make notes and keep track of your screws. When I got it rebuilt I was bumbed out at the speaker, but because there is no glue on the new free I was able to get the back off in less then a minute.
I see no gaps or problems. Everything works and the phone looks great, in my opinion they should have never made a white and silver. I'll post some picks when I'm back home tonight.
I followed the videos from Go Cell Phone Repair, he has 2, one is the tear down the other is the reassembly, Google YouTube for them, he was very thorough.
Hi guys,
has anyone of you tried changing the front glass without digitizer and display?
In disassembly videos I can only see people changing the whole thing.
Also, do you think I can manage to repair the front glas as well as the USB port with just an iron instead of a hot air blower (and the usual tools made of plastic)?
Thanks in advance!
kadofl said:
Hi guys,
has anyone of you tried changing the front glass without digitizer and display?
In disassembly videos I can only see people changing the whole thing.
Also, do you think I can manage to repair the front glas as well as the USB port with just an iron instead of a hot air blower (and the usual tools made of plastic)?
Thanks in advance!
Click to expand...
Click to collapse
I haven't done the front glass on mine yet, but my understanding is that in general you're really better off replacing front glass as an entire unit with digitizer and display. An iron on pretty low through a cloth/towel might well work. It's not just glue that melts, it's a thin strip of rubber gasket material with adhesive (okay, maybe it's thick glue, but it looked pre-formed to me) holding the glass back cover on.
Heating probably helps a bit with softening the stuff, but after the first time you peel it up you won't really need to do that again. I'd recommend picking a corner (say, bottom left as you're looking at the back) and just plan on prying from there every time, so you only have one spot where the plastic gets marred.
Don't spend too much time heating, worry more about having a suction cup tool that you can lift with while you try to work a guitar pick or hobby knife or something in under the corner. Have at least two ready, so you can wedge one in, and work your way around without it just dropping back down on you. You'll probably tear the material a bit but that's okay, just spread it back out evenly around the edge on the glass before you put the cover back on. Also, you definitely should be using a case to make sure it doesn't just fall off in your pocket once you've opened it up a couple times.
USB cable replacement isn't awful, just time consuming. The biggest gotcha is to keep all three of the little gold clips on the plastic "mid frame" ring (that's the first thing you remove that requires screws after getting the back glass up) from fallling and getting lost.
You can PM me if you have any questions about this, I've replaced my USB cable/port assembly a couple times (first replacement was defective). And I'm about to attempt replacing the screen as a whole unit with glass & digitizer on my wife's Z2 Plus, so I'll let you know how that goes.
Hey guys,
unluckily my Display (not the glass) got broken so I have to replace it and also ordered it already. After watching a few teardowns I have two questions:
Do I have to remove the back or can I just warm up the adhesive and take the screen off?
Can I use glue to replace it or do I have to use tape and can I use normal nail polish remover to remove the adhesive residue?
Sincerely
unins000 said:
Hey guys,
unluckily my Display (not the glass) got broken so I have to replace it and also ordered it already. After watching a few teardowns I have two questions:
Do I have to remove the back or can I just warm up the adhesive and take the screen off?
Can I use glue to replace it or do I have to use tape and can I use normal nail polish remover to remove the adhesive residue?
Sincerely
Click to expand...
Click to collapse
You can go through the front, but it definitely would be more risky since all components will still be connected.
I would personally not use glue. Glue is meant to support more rigid materials and the components in the phone are quite fragile. Though you could use very thin electronic glue. Not sure how well that would work.
Regarding the nail polish remover, I would not use that unless the content of water is <10%. You want at least 90% alcohol content for cleaning the adhesive. Your best bet is IPA (isopropyl alcohol). It will clean better and will not risk water damage to any components inside the phone.
So you say I have to do it from the back?
What is the risky part of going through the front?
Because of glue: Can I use any double sided tape I want?
So now I opened the ROG Phone 2 through the back and made the following experiences. And for all those who are wondering the same:
In my opinion you can't go through the front because the display is connected with a flex cable through the middle frame (which is indepentend from the display so the display comes without a middle frame where the components are assembled in like in many other smartphones) to the motherboard. Though there is a cut out in the middle frame for it but the motherboard blocks it so far that only the cable itself can go through and not the connecting port. Maybe you can disconnect the display but not connect the new one without disassembling the motherboard from the middle frame. And that's only possible with going through the back and loose the screws. In additon, especially after a fall, there can be more components be broken as just the display. In this case you can connect the new display and check all the functions before glue it together back again.
Because of the glue:
There is a glue available in two colors called B-7000 and T-7000. One of them is black and the other one is transparent depending on the color of your smartphone. These glues are especially made for smartphones. If you watch the Display replacement videos for the ROG Phone 2 you can see that they are using this type of glue and not double sided tape since it has to be 1 mm or narrower to be able to glue the display with the middle frame again.
For the back you can use double sided tape.