XDA 2i touchscreen - PDA2, XDA IIi, 2020i General

I bought a replacement digitizer off ebay and they have sent me the generation 1 version.
Before I go and buy the right one can anyone tell me how easy it is to solder the correct one and also if anyone needs a generation 1 version I have a new one here and would be happy to sell it on.
Thanks

its a ***** to do, i just replaced one on my dads xda2, but its the same as the xda2i
after taking a long time to carfuly remove the original without damaging the lcd, i used a safty blade and slid it between the buggered digitizer ad its plastic mount, be VERY carful as u need to apply force and its easy to slip, as i first did and sliced a 2" gash into my thumb... not good. second time i was alot more carful. by putting the screen edge down on a table top and wiggling the blade down all 4 sides, be carful not to cut the lcd ribbon!
i had to cut the 2 side tabs on the touch screens ribbon down by 3-4mm and then seperate all 4 leads, this is due to the design of the gen 2 screen i just followed the way it was originaly soldered on.
you also have to have a low wattage or cool soldering iron, around 10-15watt as it is very easy to damage the contacts i heated the solder on the lcd side and pressed the digitizers ribbon onto it with a small amount of flux, then used a flat screwdriver to quickly cool it down the area, you also have to put slips of paper between the 2 sides leads and the center 2, as it will short out, this was also done originaly.
sounds hard to do but its easy with a little patience, and soldering skills.
i bought it from ebay as well
p.s. do not glue the new digitizer with superglue as you will damage the screen, i just placed it back in the case without sticking it in, been fine for the last few weeks but a few VERY thing strips of double sided tape will do or if your lucky some of the origial sticky stuff will be left over.

does this "digitiser" thing is the faulty part which causing the PDA screen to have so-called Dead area ?
or "missing area"
because I won O2 XDA IIi which can't create straight line at the bottom of the screen.
where and is there any tutorial on how to replace such thing ?
Cheers.

Related

How to replace Nexus Digitizier/Glass

So last week I cracked the glass on my poor Nexus. It took a horrible drop. Well I can't afford another Nexus and I can imagine having any other phone so I figured I'd repair this one. Read up alot on it and watched a video on Youtube. Ordered all the parts I needed I tackled it today.
Well I decided to do a How-To for any other Nexus owner with broken screens.
New digitizer - $40
Torx screwdriver -$5
Philips screwdriver -$5
Plastic tools - Free
Total - $50
Sure beats the $125 some online sites charge.
I would like to thank ifixit and slickromeo.
1. Gather all your tools and replacement glass (known as a digitizer).
Note: Needed tools are a Philips #00, a Torx T4, and a plastic pry tool (Mine was included with the new screen)
2. Set up a clean comfortable area to work in. You may be here for awhile and you're going to want to reduce the amount of dust that could potentially get on the new glass.
Note: I used a folded over microfiber towel to keep the area clean and also add some padding to the hard counter top to prevent even more damage while working with the phone.
3. Power phone off and remove battery cover, battery, SIM card, and Micro SD card. Set aside in a safe place.
4.Our first obstacle is going to be the antennae cover at the bottom of the phone. There are three plastic clips holding it in place (Circled in red). Use a combination of the pry tool, a guitar pick, butter knife, and any other instrument you need to shove in there. It is a pain in the ass... the video I watched online made it seem like it was going to be alot harder than it was, but if you work from left to right, or right to left, and get the outside one unclipped the other two come off pretty easy. Once you get it off set it aside with the battery cover and other things.
Note: Be careful not to break these tiny, fragile clips as they are the only things holding this cover in place.
5. Scream profanities and wipe the sweat off your brow from the previous step. I know it was frustrating and nerve racking trying not to break your precious Nexus.
6. Ok good job now to start the real deconstruction. I'm going to start with the battery tray and then move down to the antennae. There are three screws holding the tray down, but before we start on those there is this tiny ridiculous little "VOID" sticker covering up one of them. I wasn't able to remove it intake, partly because I don't really care about my warranty, but I'm sure with alot of patience and tweezers one could take it off intake and put it back. But screw that just get it off to get to the screw underneath.
7. Now two of these screws is a Torx and the third is a Philips (All in green). Remove them and put them somewhere very safe.
Note: I have four plastic cups set up to place my screws into. These are going into the first one.
8.Next you need to remove the battery tray. There are seven tabs (yellow circles) around it that you need to release using your plastic pry tool. Once those are released gently pull away form the bottom of the phone to remove the tray. Set the tray aside.
9. Now for the antennae cover. There are two more screws to remove, a Torx and a Philips (Orange circles). These screws are going in the second bowl. After the screws are out, gently lift up on the bottom of that cover and it should remove easily. Be very careful not to damage the circuit board during removal.
10. Next to come out is the logic board. there are two more very tiny screws to remove (White circles). Into the third bowl with those. Next you need to disconnect three connections (purple circles). Then carefully go around the perimeter of it with your pry tool and VERY CAREFULLY remove all the little tabs holding it in place. Then simply push up form the bottom of the logic board and slide it out. Set it somewhere very safe.
11. Now onto the actual case of the Nexus. Remove the six Philips screws, 1 at the top and 5 at the bottom . Again there are a series of little clips, five of em, around the perimeter that need to be undone and then the case very easily separates from the screen. Set the case aside.
12. Very simply pry the LCD screen away form the glass digitizer. There it is... the broken glass.
13. Now take your pry tool and from the back of the glass (not the side you would touch if you were using the phone) wedge it between the frame and the glass to separate to adhesive. Once the pry tool is in you can just slide it around the edge of the glass to separate the whole thing. TA-DA your broken glass is forever gone.
Note: The glass is broken and very sharp. Take extreme caution not to cut yourself.
14. Now we just have to put the whole thing back together. Start with the new glass/digitizer. Peel off the plastic protector to expose the adhesive and very carefully put it in place.
15. Wrap the connector that is part of the digitizer around and secure it in place with its adhesive.
16. Take the whole screen assembly and slide it back into the case. Push to secure the clips then replace the six screws that you removed.
17. Slide the logic board carefully back into place. You may have to hold down/more out of the way a few of the connectors. Take it a little at a time and see where it is getting caught up. You got this far don't lose your patience.
18. Snap the back antennae cover back in and replace its screws.
19. Slide the battery tray into place and replace its screws.
20. Snap the gray antennae cover back on.
21. Replace Micro SD card, battery, and battery cover.
22. Enjoy the beauty of your Nexus without a broken screen.
23. Place Nexus in Otterbox Defender case so this never happens again.
I have pictures that document each step but need to be approved by a moderator before it lets me post em... sorry guys
Hey, awesome job on fixing your screen. I would love to see them, my Nexus just went through the same thing 30 min ago. I had it on my lap, and upon stepping out of the car, SMACK, is all I heard. It landed face down and this is the aftermath. It's much worse than it looks in the picture.
Man, that sucks. I know that feeling.
I'll try to put the pictures up to help you out. Or at least a link to my photobucket.
Sent from my Nexus One using Tapatalk
thanks! I just cracked mine yesterday after the phone fell out of my pocket onto a concrete floor. Ouch. I'm giving this a whirl.
Nice, I'll keep this in mind for the day I accidentally break my n1.
I just wish we could somehow jury-rig the Incredible digitizer to our phones =/
I just recently converted to the n1, bought the phone for cheap off craigslists, but notice burn in on the screen, will changing the digitizier also fix the burn in?
Thank you so much for taking the time to do this write up. I just dropped my phone and smashed the screen on concrete 30 mins ago. All is working but the glass is cracked. I've ordered a new Digitizer/Glass from ebay for £30, I just hope it comes by tomorrow.
you can post picture after 5 posts so it should be good now you have 8 posts
I've just completed the work of replacing the broken glass.
I used your guide throughout, it's a shame you haven't been able to post the pictures as it definitely would have helped. I managed to google some dismantling pictures to help with your talk through as it was hard going some times.
Many thanks again.
Another useful tip: run an air purifier aimed at your work station to minimize the risk of getting dust in the glass.
blueboymj: Any chance you can edit your original post and add your pictures so others can use them? I searched quite a lot for a specific procedure to change the digitizer on my poor N1; This was the best, most accurate guide I found. I've done digitizers on a few iPhones (sorry for the profanity) using the ifixit guides, but alas, the ifixit guides were better for them than they are for the N1.
On a side note: The end cap that gives people so much trouble fell off of my N1 in the initial drop. I pushed it back on, and continued using the phone even though the glass was shattered. Removing it the first time was not so hard, I think it was not back on as well as it should have been. Removing it the second time (another story) was much harder. There are two little plastic "bars" on the end cap (step 4 above) that fit into small grooves on the "antenna cover". (step 7) I think the trick may be to possibly pinch the edges of the end cap, while sliding it toward the bottom of the phone. I looked at it after it was open, to see why it was so hard to remove, and realized I had been inadvertently helping it hold itself closed while trying to pry it open. Maybe one of the videos addresses this; I did not watch them.
Thank you to the OP and the responders for this post!
So where exactly did u order the new digitizier and parts from?
Sent from my Nexus One using XDA App
This thread should be added to the N1 wiki. Thanks for the instructions.
DrewOntheMYT said:
I just recently converted to the n1, bought the phone for cheap off craigslists, but notice burn in on the screen, will changing the digitizier also fix the burn in?
Click to expand...
Click to collapse
Burn in? Like shadowing on the LCD? Nope.
Thats the LCD, and is completely different than the digitizer. The digitizer is just a clear plastic/glass layer that goes OVER the lcd to detect touch.
I had the digitizer and a new case and was going to have a local phone store replace this for me. However, they just gave me some BS story about how you cannot replace the digitizer without also replacing the LCD screen, which I did not provide.
So I've been without a phone (since they have it) for no reason and have to drive out of my way to retrieve it.
Hey crappy phone store, if you're too scared to do the job just say so, don't try to make up a bunch of manure and say it can't be done.
Anyway, I just ordered the required tools that I don't have and am going to give this a whirl.
OP, if you can't post your pics, can you email them to me?
does it fix the multitouch problem?

[Q] Scratched screen- How do I replace it?

The screen on my Rogers HTC Raider is scratched. It is deep enough that I cannot remove by applying polisher. Screen still works but I rather replace the screen as the scratch is visible.
Where can I purchase the screen and replace it myself?
http://www.tmart.com/Replacement-LCD-Display-Screen-for-HTC-G19-Raider-4G_p137438.html
http://www.repairsuniverse.com/htc-vivid-screen-replacements-repair-parts.html
..
Thank you.
tap the thanks button
and good luck
A little advice - I've already replaced the screen on my Raider
Hi, glad someone else is attempting this. I had never replaced a screen in a phone before trying this so for me it was a little hair raising the first time I took it apart. On the back of the phone under the battery cover are 5 screws you need to remove, and one little plastic cover. Under the cover is the connector from the mainboard. Its just a little pop out connection, gently lever it loose before removing the shell to avoid hurting the ribbon.
Once you get this far, flip the phone face-up, and *from the bottom*, gently lever the sides and bottom of the plastic shell away from the screen. Its relatively easy.
Continue working along the edges toward the top until the plastic shell pops free, after that put it face-down again and remove the screws holding the battery holder to the rest of the phone. Pull it up and out to the left to remove it, being careful not to bend the battery contacts as they stay with the rest of the phone. Keep the screws with it, trust me - its easier to remember what goes where this way.
Once you have the battery holder off, put it aside and remove the screws holding the mainboard(s) to the shell. Also you will find three wires with little cup contacts at the ends, gently detach these as well, and when the screws and wires are off, carefully remove the boards. Look closely at the plastic tabs holding them in and you'll see how they come out. When taking them out of the phone you'll need to lift them like you were opening a book - ie. folding them to the right. Underneath are two sockets with ribbon cable connections, one should already be detached - the other can be popped off at this point. If you skipped detaching it at the beginning, now's the time to remove both.
This should leave you with two free boards attached in the middle by a black ribbon. Put them aside and what you have left in your hand is the metal shell, LCD, and digitizer.
NOW..the crappy news. This wonderful, beautiful, powerful, ESPENSIVE phone, is held together by black double-sided tape. Yep. Tape. AND you'll need some more before installing the new digitizer. I ordered mine from tmart as well and it not only comes with the wrong screwdrivers (btw you need a #1 philips bit - VERY tiny!!) but it doesn't come with any adhesive to mount the screen to.
Your new screen should also come with some prying tools, and they are quite handy. The guitar pick one didn't do much but the lever is very handy. You'll need to gently pry the digitizer away from the LCD with this tool being careful not to put too much pressure on the lcd or it might snap. Its only a few mm thick. GO SLOW.. you should have no problems. I've done it a few times now - I'm kinda rough on my toys.
Once you have the part un-taped, its still got the ribbon cable going back behind the lcd. Its connected to a small, thin socket on ther board. You lift a small white lever (remove the tape and save it - reapply it to the new connection) and slide the cable out. You'll need to use your lever again and pry up the lcd enough to slide the ribbon out from behind it. This can be tricky. Again, go slow, be real cautious..the tape is pretty strong. Once you have the panel out completely its just a matter of reversing the process. If you're real careful when removing the original panel, you might be able to reuse the double-sided tape thats in there.. I wasn't so lucky. Mine was covered in glass shards, as I mashed my screen pretty good.
Hope this helps!! I had a rough time the first time, but now its easy for me. I like taking it apart lol..
Let me know how you do! Good luck!
Brian

Raplacing the digitizer

Ok so i have a cracked digitizer...
I am going to replace it myself, however this phone is obviously not a straight forward repair.
Anyone have any personal experience replacing the digitizer on this phone? I have seen the youtube videos and read the xda.cn chinese breakdown, just looking for some personal input on the process if someone has one.
Also what will i need to rebuilt it? Do i need double sided tape etc. Thanks
80 views and no ones ever had experience with this?
i replaced it on 2 hd7 phones.
its a real pain to get it off because the glue tape they use goes all the way around, and its strong stuff.
you need to take apart the entire phone to get to the ribbon cable where the digitizer plugs in, so just look for some youtube videos of a tear down and watch carefully.
honestly the hardest part for me was getting the screen and digitizer clean of fingerprints and tiny broken glass pieces without messing up the screen, while keeping the double sided tape i put on in place and intact.
just take your time and everything will go smoothly.
-edit- yes you will need some double sided tape because when you take the digitizer off the sticky layer of the tape goes with it, the rest of the tape stays on the screen and is impossible to get off without damaging your screen so you have to apply new tape over it.
i used some thin scotch brand double sided tape and i cut it into long narrow strips with a razor using my old digitizer as a cutting board, the same width as the original tape.
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
CraiGDaniel said:
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
Click to expand...
Click to collapse
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
StevetotheH said:
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
Click to expand...
Click to collapse
um no they arent spacers...they are what directs the light to the 3 bottom keys. they are there for a reason so i recommend using them... ... now you are spot on with the 3m tape as it is the tape needed to do this whole job properly... the scotch crap is not made for this and WILL NOT HOLD UP NOR SEAL PROPERLY>>>
and for the person who said to put the tape over the old.... not a good idea... it can be removed and new should be used to replace the old..
sorry but i do this daily for a living so i do have a clue about this... just trying to help make it a successful repair and not one that ends up in my shop after the home repair failed and it damaged more than just the screen.....

[Q] Replacing digitizer

I've cracked the outer layer of glass on my optimus x2 which I assume is just the digitizer (I'm new to all this smartphone jazz but i've had alot of experience with building computers and such and i can follow instructions) and i'm guessing the cheapest way to repair this thing is to do it myself. I emailed LG asking about what they can do with it and they were asking for £20 just to look at the damn thing so i can't imagine actually doing any work on it would be cheap.
(can't post links but it was just some cheap generic one from amazon for £30)
I'm guessing something like this would do the job but I also need some special adhesive to get the LCD to stick to the digitizer am i right? I'm worried that it will not be as responsive or i'll do it wrong and i only recently dished out £250 for this so i'd like to try and do this right. I've watched a couple of videos on youtube which have helped a bit but none went right through the process so if anyone with any experience doing this could tell me about it i'd be very grateful.
its not that hard. everything just peels off when heated with a hair drier.
the digitzer should come with sticky strips which go around the outside of the lcd and stick to the out side of the digitizer.
Also try to get a digitizer with a frame already on it. otherwise youll have a little bit of a hard time trying to remove the glass from the frame, then gluing in the new one with adhesive.
http://www.youtube.com/watch?v=K77Xepb6yd8
Just follow this guide exactly, you should be fine man
Supupa said:
its not that hard. everything just peels off when heated with a hair drier.
the digitzer should come with sticky strips which go around the outside of the lcd and stick to the out side of the digitizer.
Also try to get a digitizer with a frame already on it. otherwise youll have a little bit of a hard time trying to remove the glass from the frame, then gluing in the new one with adhesive.
Just follow this guide exactly, you should be fine man
Click to expand...
Click to collapse
Thanks for the reply, that's a lot of help Could you recommend any retailer that sells these? I can't work out if any of the ones i'm looking at come with the sticky strips. Would I also not need any adhesive if it comes with the frame? I'm not sure I trust myself too much with doing that either.....
I recently replaced my digitizer. I ordered a digitizer already in housing off ebay, shipped from Hong Kong. I would strongly recommend buying it with housing, as it's often difficult to completely make sure that dust does not get between the digitizer and the screen when you're using adhesive tape.
When disassemblying the o2x, I found the adhesive sticking the LCD to the digitizer frame was too strong for the LCD to come off just like that (be careful, it's quite fragile). I heated the LCD a bit using a hair dryer, to make it come of easier. This has the added effect that enough adhesive may stick to the LCD, so you don't need to replace it when placing it in the new frame.
I only added a couple of adhesive strips to the top and bottom of the new frame before mouting the LCD. That was pretty stupid, cause the extra 0.1mm between the digitizer and the LCD means that when tilting the phone ~60 degrees to the sides, I can see the backlights at the sides of the screen. Surprisingly this doesn't seem to add any noticeable backlight bleeding though, so it's not a problem at all. However, I'd suggest to try and see if the LCD sticks to the frame with the old adhesive, before using adhesive strips. And if using adhesive strips, make sure you remove all the old adhesive from the LCD, and use adhesive strips all around the frame.
The only minor things to look out for are:
- Be very careful with the LCD! It takes very little flexing before getting dead stripes/areas.
- Careful with the plastic at the USB port - it's a bit difficult to get to fit, and it's quite thin, so I figure it will break easily.
- At the top of the phone, where the digitizer (or LCD, I don't remember) cable is mounted, there's a little grey rubber-thingy - it suddenly fell off my phone, and it took embarrassingly long to figure out where and how it fits
- The small backup battery (?) in the upper left corner of the phone is glued to the frame. I used a small flat-headed screw driver to release it from the frame. Don't try and remove it by yanking the flex cable.
But all in all, replacing the digitizer with a new one (already in a frame) was a quick and easy operation.
Edit: I bought this digitizer: ebay. co. uk/itm/T-Mobile-LG-P990-Optimus-2X-Replacement-Touch-Screen-Digitizer-Frame-ZVLT338-/160656180054?pt=UK_Replacement_Parts_Tools&hash=item2567dac356 and some cheap 2mm adhesive strips like ebay. co .uk/itm/3M-Sticker-tape-Adhesive-cellphone-touch-screen-LCD-2mm-HTC-Samsung-Sony-/200710386131?pt=UK_Mobiles_Accessories_RL&hash=item2ebb4571d3#ht_1099wt_1165
Why didn't I think of this before.. been cracks in my display for almost a half year now.
Local repair company said it takes two weeks to fix.. I had no plans to go two weeks without my phone
Just ordered one
p990 mother board
dear friend
sorry for my eanglish i write from italy.
i need your help but before i have to explane my problems:
i've a lg optimus x2 (p990) with water demage.....
i cleaned the mother board with success..now the phone turn on and fix the phone net and it can recognize the battery charge.
but unfortunately WI-FI,BLUETOOTH AND MIC(the people who call me can't hear me) DON'T WORK, THE GPS I DON'T KNOW BECAUSE I HOPE TO RESTORE THE WII-FI AND INSTAL GOOGLE MAPS.
i'm sure that wi-fi problems come from the mother board because i have an other same device so i made a test using the good one but the mic problems persisted
my question is ,do you know wich parts i have to check and clean again?
do you know where the wii-fi component are located in the mother board?
thanks for your attention
a friend
marco zavatta
Sorry for bringing up this old thread, but I have to ask, are all Optimus 2X digitizers the same? Don't some have different connectors or anything? Can I order any Optimus 2X digitizer for my P990? I was thinking of this digitizer, will it work?: http://www.amazon.co.uk/Digitizer-F...7BUA/ref=sr_1_1?ie=UTF8&qid=1364833172&sr=8-1
I had to replace mine recently, I read there are cheap ones where they only recognize 2 fingers instead of 5 like the genuine LG part. I ordered my digitizer from Ebay for around 18 british pound, I followed a few videos on Youtube with the disassembly, it's actually not that hard.
Keep in mind though that not all digitizers might come with glue attached or come with plastic tools, so keep a small bottle of glue and some plastic tools (credit card style plastic, knife) ready. One video recommends buying foam pads to glue around the digitizer, I didn't find that necessary, I just glued my new digitizer back onto the frame without problems. I accidentally made some glue residue onto the inside of mine, so make sure that you work very carefully
I have done this twice. It is not too hard and a lot cheaper. I follow this guide: http://www.youtube.com/watch?v=Po8hBaZt__o.
Do yourself a favour and buy a digitizer with bezel (which is a frame). The first I bought was ****ty Hong Kong digitizer, the second one good Polish(?): http://www.ebay.co.uk/sch/m.html?_nkw=p990&_sacat=0&_odkw=&_osacat=0&_armrs=1&_ssn=digitaloutlet.pl
The hardest part is not to get dust between digitizer and lcd screen - you could consider wearing gloves...
The second hardest part is not to bend bezel around usb inlet.
Good luck!
So there's no connector difference?
kaspar737 said:
So there's no connector difference?
Click to expand...
Click to collapse
The connector should fit any p990. If you are in doubt email the seller.
oneearleft said:
The connector should fit any p990. If you are in doubt email the seller.
Click to expand...
Click to collapse
Sorry for coming back to this rather old thread, but I have recently replaced the digitizer on my LG P990, bought on ebay shipped from Hongkong, following the video guide cited above. However the digitizer now works erratically with upper 1/4 not responding to touch, and sometimes the whole thing does not work, so I am unable to unlock the phone at all. The only thing that worried me during replacement was the thin layer of plastic film on the inner side, which teared off when removing protective layer (the film was extremely thin and fragile)-would this be the problem? Or the digitizer itself is of low quality?
Any suggestions appreciated.

OEM LCD/Digitzer? i need your input - i love my LG G2

lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
I'm in the same boat as you. Dropped my G2 while getting off pickup truck and the digitizer is kaput. I have no touch response anywhere on the screen. But the LCD is working really well. No damages to that.
So i'm looking for a digitizer as well to replace it.
gunemalli said:
I'm in the same boat as you. Dropped my G2 while getting off pickup truck and the digitizer is kaput. I have no touch response anywhere on the screen. But the LCD is working really well. No damages to that.
So i'm looking for a digitizer as well to replace it.
Click to expand...
Click to collapse
i am looking for the LCD and digitizer assembly. but i am trying to find OEM part
sdcaliber said:
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
Click to expand...
Click to collapse
When my wife broke the digitizer on her n4, I was in the same boat. I searched earnestly for TRUE OEM parts. What I discovered was this site:
http://www.etradesupply.com/catalogsearch/result/?q=LG+VS980
They are the most expensive, but to my knowledge it is TRUE OEM.
Due to time constraints, I ended up getting a screen on Amazon that claimed to be OEM, and while the screen and digitizer assembly I could tell were brand new OEM parts, the housing had been recycled, as it was missing some adhesive for the board components. While her screen works fine now, it lacked the filter for the led notifications light (as it was a recycled housing) and was more difficult to replace due to the fact I had to conserve the adhesive film off the old housing and transfer it to the new housing. If I had to do it again, I would pay the extra and get the TRUE OEM brand new from etradesupply.com
Good Luck!
PS. If you need a good youtube video for the repair, I recommend this guy: https://www.youtube.com/user/LE55ONS
housing is not an issue
Lttlwing16 said:
When my wife broke the digitizer on her n4, I was in the same boat. I searched earnestly for TRUE OEM parts. What I discovered was this site:
http://www.etradesupply.com/catalogsearch/result/?q=LG+VS980
They are the most expensive, but to my knowledge it is TRUE OEM.
Due to time constraints, I ended up getting a screen on Amazon that claimed to be OEM, and while the screen and digitizer assembly I could tell were brand new OEM parts, the housing had been recycled, as it was missing some adhesive for the board components. While her screen works fine now, it lacked the filter for the led notifications light (as it was a recycled housing) and was more difficult to replace due to the fact I had to conserve the adhesive film off the old housing and transfer it to the new housing. If I had to do it again, I would pay the extra and get the TRUE OEM brand new from etradesupply.com
Good Luck!
PS. If you need a good youtube video for the repair, I recommend this guy: https://www.youtube.com/user/LE55ONS
Click to expand...
Click to collapse
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
I bought from ebay one of the ones claimed to be an origiginal oem screen. Works perfect and do blemishes etc.
i bought one
squee666 said:
I bought from ebay one of the ones claimed to be an origiginal oem screen. Works perfect and do blemishes etc.
Click to expand...
Click to collapse
i did buy one from ebay today, after been an annoying person with lots of questions hahaha. i refused to buy from anyone below 99% profile credential on ebay. here are the questions i asked lol
Is the LCD screen manufactured by the same company that I would find on brand new in box phone that I purchased from an authorized store? if not, is the same Quality, TRUE IPS LCD with Gorilla Glass 2 digitizer?
Is this LCD part brand new or refurbished from reclaimed old parts?
Digitizer – Is the Touch Panel manufactured by the same company that I would find on brand new in box phone that I purchased from an authorized store?
Digitizer – Is the Touch Panel new or refurbished, or reclaimed from old parts?
and if I bought a brand new in box sealed G2 from LG, the part I’m asking about would be 100% identical with no differences in quality or condition?
does it work on D800 model, if not do you have one that works with D800 that is a genuine OEM?
is it OEM (Original equipment manufacturer), does it have part number on the flex cable, and LG display co,ltd label ?
only one seller, answered all of them concisely, without political correctness or avoidance. lots of them stopped talking to me, and some only answered vaguely. i had one hilarious response, who said the the screen is OEM but not genuine, i insisted for him to elaborate, he said OEM but not original. all of us know that OEM stands for Original equipment manufacturer. i sent him a response, that it does not make sense to be OEM but not original. he replied back OEM for them is, Optical equipment manufacturer lol, heck i do not even know what does that mean lol. i took a screenshot of the definition and sent it to him, he never replied back hahaha. many shady seller on ebay
P.s once i receive the part and install it, i will update on the condition/quality
can post the link for the seller you bought the assembly?
thank you!
Link
noris08 said:
can post the link for the seller you bought the assembly?
thank you!
Click to expand...
Click to collapse
http://www.ebay.com/itm/251591046010?_trksid=p2060778.m2749.l2649&ssPageName=STRK:MEBIDX:IT
working
update,
as i provided previously with the link of the LCD/Digitizer, i promised to update after purchase and assembly.
i self repaired myself, took me about an hour and Half give or take. it works like a charm, no problem whats so ever.
advise, before attempting to do it yourself, find a youtube video of how to disassemble and reassemble, including how to apply the adhesive (took most of the time).
i can confirm, and take my words for it, the one i bought is an OEM LCD digitizer.
cheers,
sdcaliber said:
update,
as i provided previously with the link of the LCD/Digitizer, i promised to update after purchase and assembly.
i self repaired myself, took me about an hour and Half give or take. it works like a charm, no problem whats so ever.
advise, before attempting to do it yourself, find a youtube video of how to disassemble and reassemble, including how to apply the adhesive (took most of the time).
i can confirm, and take my words for it, the one i bought is an OEM LCD digitizer.
cheers,
Click to expand...
Click to collapse
Can you provide any info on how u got the screen to securely cit in the frame, like what adhesive did u use and how u did it?
I did the repair my self the phone works great except the bottom ov the screen, sticks out abit n I can see the back light, very annoying
jamracer said:
Can you provide any info on how u got the screen to securely cit in the frame, like what adhesive did u use and how u did it?
I did the repair my self the phone works great except the bottom ov the screen, sticks out abit n I can see the back light, very annoying
Click to expand...
Click to collapse
absolutely,
keep in mind the following things,
i used 3mm double sided adhesive tape, you can find them on ebay for 2 dollars give or take. the hard part laying out the tape in correct manner. you have TWO WAYS to do it that i know of using the tape, whatever that suits you. first one, most people will place the tape on the housing (if you did that, avoid placing the tape over the proximity sensor, camera, the usb, and the connection ports. or it will be a pain to remove them and damage maybe imminent in such situation ). the trick part, is the tape in vertical position around the edges where the bezels of the screen will sit (if its done incorrectly, you will have the problem you have described). therefore i will share the second method, my method :
check if the screen and digitizer works correctly before finally putting the adhesive;
WARNING: if you are not sure what you are doing, please consult with phone technicians for a professional fix. this is only my method/my opinion and in no way constitute a professional advise.
it is separated in to three parts
1 - use 3mm tape to tape the bottom and top of the housing, i repeat do not tape, the proximity sensor, camera, the ports, or the usb, use common sense or youtube to see which one is which .
2 - use the 3mm tape and tape the edges behind of the screen under the bezel (on the screen/digitzer assembly itself, not the housing). it is a narrow spot to tape, that where most people end up with popping out screen at the bottom edges and seeing the light. due to the narrow edges, use a small tweezers to place it.
3- use the 3mm tape and tape the edges of the housing where the bottom of the screen will sit (optional). in my case, i did that also
now peel the double sides 3mm tape, using tweezers will make it easier, much much easier.
once done, take your screen/digitizer assembly, and insert the bottom flex cables first into the housing (they are two cables, be careful, they are fragile), make sure the bottom part sit perfectly and all the cables are sitting correctly into the housing, before you insert the top flex cable (longer thinner cable).
insert the flex cable (the top one, into the housing slowly, while checking around with your eyes, that everything is aligned with the housing. once the flex cable in, double check and see if the flex cable is seated perfectly. check around the phone edges, and if everything is perfect, press gently on the edges, until the adhesive makes contacts. if you find that the screen is not sitting correctly, gently lift the phone slowly, and position it correctly before the adhesive sticks (takes about two minutes before the adhesive taking effects, keep that window in mind).
after the everything is sitting where it suppose to, place everything back inside the phone, turn it on and check again if its working along with the digitizer (i recommend checking whether the screen and digitzier works before placing the adhesive). once you check everything is working fine, turn the phone off, and unplug the battery cable from the motherboard.
use hair dryer (on low) or heat gun (use low temperature), hair dryer is safer if you are not sure what temperature to use with the heat gun and heat around the edges of the screen (keep it moving and do not stay in one place) this is for the final seal, about 30 to 40 seconds of heating. now the screen is sealed shut. leave the phone to cool down for a minute (optional: use a rubber band around the top and bottom for added pressure, not too tight though). plug the battery cable in and reassemble the phone.
cheers
sdcaliber said:
absolutely,
keep in mind the following things,
i used 3mm double sided adhesive tape, you can find them on ebay for 2 dollars give or take. the hard part laying out the tape in correct manner. you have TWO WAYS to do it that i know of using the tape, whatever that suits you. first one, most people will place the tape on the housing (if you did that, avoid placing the tape over the proximity sensor, camera, the usb, and the connection ports. or it will be a pain to remove them and damage maybe imminent in such situation ). the trick part, is the tape in vertical position around the edges where the bezels of the screen will sit (if its done incorrectly, you will have the problem you have described). therefore i will share the second method, my method :
check if the screen and digitizer works correctly before finally putting the adhesive;
WARNING: if you are not sure what you are doing, please consult with phone technicians for a professional fix. this is only my method/my opinion and in no way constitute a professional advise.
it is separated in to three parts
1 - use 3mm tape to tape the bottom and top of the housing, i repeat do not tape, the proximity sensor, camera, the ports, or the usb, use common sense or youtube to see which one is which .
2 - use the 3mm tape and tape the edges behind of the screen under the bezel (on the screen/digitzer assembly itself, not the housing). it is a narrow spot to tape, that where most people end up with popping out screen at the bottom edges and seeing the light. due to the narrow edges, use a small tweezers to place it.
3- use the 3mm tape and tape the edges of the housing where the bottom of the screen will sit (optional). in my case, i did that also
now peel the double sides 3mm tape, using tweezers will make it easier, much much easier.
once done, take your screen/digitizer assembly, and insert the bottom flex cables first into the housing (they are two cables, be careful, they are fragile), make sure the bottom part sit perfectly and all the cables are sitting correctly into the housing, before you insert the top flex cable (longer thinner cable).
insert the flex cable (the top one, into the housing slowly, while checking around with your eyes, that everything is aligned with the housing. once the flex cable in, double check and see if the flex cable is seated perfectly. check around the phone edges, and if everything is perfect, press gently on the edges, until the adhesive makes contacts. if you find that the screen is not sitting correctly, gently lift the phone slowly, and position it correctly before the adhesive sticks (takes about two minutes before the adhesive taking effects, keep that window in mind).
after the everything is sitting where it suppose to, place everything back inside the phone, turn it on and check again if its working along with the digitizer (i recommend checking whether the screen and digitzier works before placing the adhesive). once you check everything is working fine, turn the phone off, and unplug the battery cable from the motherboard.
use hair dryer (on low) or heat gun (use low temperature), hair dryer is safer if you are not sure what temperature to use with the heat gun and heat around the edges of the screen (keep it moving and do not stay in one place) this is for the final seal, about 30 to 40 seconds of heating. now the screen is sealed shut. leave the phone to cool down for a minute (optional: use a rubber band around the top and bottom for added pressure, not too tight though). plug the battery cable in and reassemble the phone.
cheers
Click to expand...
Click to collapse
thanks alot of the info,
i did the repair and all, the screen and digitizer works well, its just the bottom of the screen sticks up, i went ahead n ordered a roll of 3m 300lse double side tape, the dounble side tape i hav is just the regular black tape, dont think its strong enough, i will go over everything with a fine tooth comb when it arrives, i hav a sprint g2 on its way as well, do u know if the d800 and the ls980 frame is compatible??
thanks for the info really detailed
sdcaliber said:
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
Click to expand...
Click to collapse
I bought EB40 battery for Atrix HD through Etradesupply's Amazon store. I haven't had any issues with battery and lasted as promised.
Whole purpose of that project was to put battery from Droid Maxx into Moto Atrix HD and bump up capacity from 2100mah to 3300 mah.
May be different buyers have different experience or I just got lucky.
jamracer said:
thanks alot of the info,
i did the repair and all, the screen and digitizer works well, its just the bottom of the screen sticks up, i went ahead n ordered a roll of 3m 300lse double side tape, the dounble side tape i hav is just the regular black tape, dont think its strong enough, i will go over everything with a fine tooth comb when it arrives, i hav a sprint g2 on its way as well, do u know if the d800 and the ls980 frame is compatible??
thanks for the info really detailed
Click to expand...
Click to collapse
3m 300lse double side tape should be fine, as long as you use it correctly.
in regards to the frame, well that i am not sure about it. however, the LCD/digitizer i ordered was labeled OEM LS980 (sprint) VS980 (Verizon) and compatible with D800 (att- that is mine) and D801. so far, it fits perfectly. make sure it is OEM, if its not, the cut maybe off, that results discrepancy in fitting with the frame. also, double check with the seller, if the its compatible with your phone.
cheers
sshark said:
I bought EB40 battery for Atrix HD through Etradesupply's Amazon store. I haven't had any issues with battery and lasted as promised.
Whole purpose of that project was to put battery from Droid Maxx into Moto Atrix HD and bump up capacity from 2100mah to 3300 mah.
May be different buyers have different experience or I just got lucky.
Click to expand...
Click to collapse
yeah maybe, all depends of course. most of these products are subject to opinions if there is doubt about their OEM legitimacy. but for me, i will not buy non OEM for battery again, it scares the hell out of me. let's say i had a horrible experience before. i had Note 3, and bought a battery for it. the extra capacity made me drools lol, so i went with it. days later, i found the phone in total meltdown, literally. woke up from my sleep, and the phone is melting/fire.... scary scary experience. the good thing, i do not sleep while my phone next to me. it was on my table, charging.
side not: the original battery of Note 3 malfunctioned
OEM
sdcaliber said:
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
Click to expand...
Click to collapse
I bought it on Ebay and now it´s working fine, nice!!.. First I bought only the digitizer and it was faulting, but now this assembly is really working fine:
http://www.ebay.com/itm/281280382756?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Regards,
Just posting to share my experience. I bought a replacement lcd\digitizer for my G2. Once installed, i had white lines going up and down the screen.
Some devices use different panel hardware (JDI instead of LGIT) and you will have white lines after using patched kernel. You must use those kernel with "_jdi" in its name. More info:http://forum.xda-developers.com/show...&postcount=122
After flashing the new kernal the phone works great. The phone does get noticeably hotter, unfortunately, which is a little worrisome.
The kernal issue and the heat lead me to believe that what i bought was not oem.
Sent from my LG-D801 using XDA Premium 4 mobile app
Is D800 frame compatible with LS980?
sdcaliber said:
3m 300lse double side tape should be fine, as long as you use it correctly.
in regards to the frame, well that i am not sure about it. however, the LCD/digitizer i ordered was labeled OEM LS980 (sprint) VS980 (Verizon) and compatible with D800 (att- that is mine) and D801. so far, it fits perfectly. make sure it is OEM, if its not, the cut maybe off, that results discrepancy in fitting with the frame. also, double check with the seller, if the its compatible with your phone.
cheers
Click to expand...
Click to collapse
I was just working on a frame lcd assembly swap on an LS980 rev 1. The frame I bought was a Verizon LV980 and the vibrator was off buy at least 3mm, I didn't mind losing the vibrator to gain a good lcd. Then the proximity detector layout was different, the LS980 had an extra piece that fit in a hole, but it could be removed. About 5mm below that is a ground connector for the motherboard on the LS980 but not on the VS980 and the tab holding the antenna coax hit the motherboard making the frame about 0.5mm too small causing the mobo not to seat.
All of these could be amended. Shave 0.5mm of the soft metal chassis, very easy, mobo grounds in at least six other places and proximity sensor had a removable tab.
But the bottom of the chassis where the dock port/usb board sits was just too different, the LS980 daughterboard wouldn't seat, it was larger. It could be forced but only at an angle that made the usb port off-center and not parallel to the opening. My repair stopped and re-assembled the phone with the LS980 chassis complete with my damaged lcd.
-----attached pics of proximity sensor, and ground connector area, didn't take more, I was getting mad.
sdcaliber said:
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
Click to expand...
Click to collapse
Actually I bought an LCD from this company. I am very happy with it. It is true HD and the it was shipped for me in 3 days as they said. At first I was very worried with the comments but I took the risk and I am satisfied with it. I don't know why others complain about it but I recommend them.

Categories

Resources