Related
Ive downloaded official wm6 sve rom from HTC website. My herlald is stuck on bootloader ipl 1.08 spl 1.08. When i connect to computer usb is shown on the screen bottom ,but when i try to flash the rom ,error 300 invalid update tool is shown.
how can i fix this??
Official rom matching my p4350 is supposed to work,but it doesnt.
please help!!!
Hi there,
I recently had a similar problem as you, what I did was to:
- remove the battery for 5-10secs
- put the battery back
- press and hold the camera button (do not release it)
- press the power on button ( the one at the top of the phone, used for the soft resets)
- The phone will display three different colors and "IPL ...."
- Connect your phone via the USB cable to the computer, Windows XP detects that as a new hardware and installs the USB drivers for it. Pockect PC ...., just accept the driver installation when it warns you that the driver is not signed.
- Past all of that you should now be ready to use the Official ROM file from HTC, run the file, and go through the steps. It should start the ROM upgrade.
Well I hope it helps you as these steps did bring my phone back after a failed ROM upgrade.
Cheers
thanks for your instructions .
i will try and post results
Is your phone CID locked?
Because if so, you have to go to your phone provider and see if they have their own official rom!
I Dont Understand ,if Htc E-club Recognises My Serial Number,and Gives Me The Possibility To Download Sve Rom ,doesnt That Mean That I Should Be Able To Flash That Rom Into The Bricked Herald?
elizag said:
I Dont Understand ,if Htc E-club Recognises My Serial Number,and Gives Me The Possibility To Download Sve Rom ,doesnt That Mean That I Should Be Able To Flash That Rom Into The Bricked Herald?
Click to expand...
Click to collapse
Yes same i also have same problem i get Norway rom from my serial number but giving me invalid update tool
my phone
ipl 1.08.00001
spl 1.08.00001
please help me in that case
thanks in advance
i asked the costumer,the herald was cid unlocked when he bougt it,he flashed succesfully pdaviet ,then he wanted to flash wm6 but after uspl the p435o went into bootloader mode,ive been trying with many flashes with no result,please help!!
I had the same problem, and i did the download again. and it worked. try to download the upgrade again and dont forget to take of the memory card of the device.
I hope this can help you.
hi guys,
i was excited about the new Radio upgrade, so i tried to flash it. i got an error, because my SPL is 2.05. so i tried to unlock the phone using jerpelea's guide, flash to 1.09 -->success, then WWE (1.10) but an error occured saying invalid vendor ID during WWE flash. now i have SPL 1.09 on my phone and my phone is stuck on the 2nd boot screen of jerpelea's WM6.1 beta 4 ROM. my phone is fully unlocked using jerpelea's unlock guide, that's how i got to install SPL 1.09 successfully. how can i recover my phone? please help.
Update 1: i tried to flash back the original dopod 595 WM5 ROM. i mixed the RUU updater from the latest official ROM with the nbh from dopod WM5 ROM. the flashing works. when it's 100%, the phone reboots and, i got back to the same problem. stuck at 2nd/3rd boot screen. i now have IPL-0.90 and SPL 1.09 on my phone. Please help me to recover my phone. i've tried to hard SPL shown in the wiki guide, doesnt work. says invalid vendor ID crap. i really dont know what to do now.
Update 2: when the device boots, it stucks on the 2nd/3rd boot screen and if the USB cable is attached, for a brief moment, windows can detect the phone and i can even browse the content of the phone from my PC. but after that, the device disconnects itself and just remain stuck at the 2nd/3rd boot screen. the device appears to be totally freezed/hang. even the LED charging indicator will not turn off when i unplug the device from computer
i believe what i need to do now is to make a nbh image that is signed to i dont get any corrupted image message when trying to flash. i used HTC ROM editor to mix and match the SPL and IPL file so that i can downgrade the SPL to 2.05 and upgrade it again later. but i dont know how to sign nbh files.
If i were you I'd use this one =)
futureshock said:
ok i found it i didn't read further the 1st page on sspl thread
edit:
have repacked it with runme.bat and 77.7er SSPL ...
Radinly_1.54.30.10
Click to expand...
Click to collapse
At least I did and it worked =)
and then I'll highly recommend this WIM6.1 release by FutureShock: http://forum.xda-developers.com/showthread.php?p=2094056#post2094056
GL =)
I've GOT IT!!! using various mix and match method, im flashing the phone now!!! fingers crossed it'll boot later
UPDATE: DOESNT WORK! PLEASE HELP
It sure will.. Even I got it to work really fine
crap!. doesnt work. it's still SPL 1.09 and stuck at 2nd boot screen.
is there a ROM editor that works for meteor? can someone please suggest one that can be used to sign the nbh file.
jerpelea, or futureshock, please help
not good news
I think I know what do you mean. My device was in very same state like yours few mnonths ago.
Try to run mtty and the command "info 2" without quotes.
Do not forget to disable USB on activesync settings before running mtty.
You will get an answer which includes the CID of your device.
If not (this was my case), you have to send it to the repair center probably.
My device CID was Qtek_A07 (RUS) and I have tried to instal the first official WWE 1.34 ROM update (combined from SPL.nbh and ROM.nbh) and it replaced only the SPL, and the ROM update crashed.
There was not way out so I sent it to the repair center.
The WWE images are expecting the device with CID Qtek_Z12.
PiGeonCZ said:
I think I know what do you mean. My device was in very same state like yours few mnonths ago.
Try to run mtty and the command "info 2" without quotes.
Do not forget to disable USB on activesync settings before running mtty.
You will get an answer which includes the CID of your device.
If not (this was my case), you have to send it to the repair center probably.
My device CID was Qtek_A07 (RUS) and I have tried to instal the first official WWE 1.34 ROM update (combined from SPL.nbh and ROM.nbh) and it replaced only the SPL, and the ROM update crashed.
There was not way out so I sent it to the repair center.
The WWE images are expecting the device with CID Qtek_Z12.
Click to expand...
Click to collapse
this is what i get with mtty
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
what's the meaning of this? is there any hope?
i ran the format command anyway. device reboots and still stuck at the windows mobile logo screen. what should i do next?
alexnvidia said:
this is what i get with mtty
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
what's the meaning of this? is there any hope?
i ran the format command anyway. device reboots and still stuck at the windows mobile logo screen. what should i do next?
Click to expand...
Click to collapse
why did you format ?
try to reflash 1.09 spl
and after this wwe one of 1.34 roms to get 1.10 spl
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
Click to expand...
Click to collapse
jerpelea: First of all I will say thank you for taking all that time you do spend on the ROM cooking/building/making/what-ever-is-the-right-name and I/we really appreciate it!
jerpelea said:
but i dont know if you have the knowledge
Click to expand...
Click to collapse
I think that comment was really unnecessary!
As a n00b I know how hard it is to understand what’s happening. I did read the wiki’s and still I didn’t get HOW TO upgrade a ROM until I found a great post in FutureShock’s thread
darkDirk said:
First of all:
It's fantastic what you are doing with wm6.1 and the Breeze, Futureshock !
I am new and trying to upgrade it myself, but at first I didn't have any luck.
Here is a simple newby step-by-step manual:
- Download and extract a MTeoR-FutureShock-WM61-xxxx.x.rar
- Check your Mteor battery in more then 50 % full
- connect the Mteor to the computer via usb and check if Activesync works
- go with DOS (cmd line) to the directory and start runme.bat
- On the Mteor press camera and powerbutton at the same time.
- then immediately press any key on the computer to continue the batch script.
- now you should see the 3-color bootscreen
- press any key to start the rom-update program and follow its directions.
When the update is finished (in less then 5 minutes), then wait untill the first boot is complete.
If you don't get the 3-color bootscreen or you the update on the Mteor stays on 0 % and the rom-updater displays an error, try testing this:
On the Mteor start the explorer and in the root directory (press UP once) find SSPL.EXE en start it.
If the Mteor won't start the program and there is an error like "insufficient trustlevel".
You need to remove the application lock on your Mteor.
Run SDA_ApplicationUnlock.exe on your PC with Activesync working and then install SP_AllowCertificateInstall.cab on the Mteor.
You will find those two in the .rar in ".\opt Software\Unlock Tools"
Then redo from the start.
Then, Have fun !! (Futureshock & DarkDirk)
P.S. works on a BREE100 with IPL-0.90 and SPL-2.05.
Click to expand...
Click to collapse
But I still do not know what SSPL, SPL, IPL or whatever there is does to me or/and the phone.
Anyway. Thanks for all the work.
if someone has a corrupt CID just send me an pm...
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
Click to expand...
Click to collapse
with all the respect what you do for this community, isn't taht you who advice us to update the SPL before trying your images?
in this thread http://forum.xda-developers.com/showthread.php?t=384398 you should probably higlight that the update should be done only on WWE devices.
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
Click to expand...
Click to collapse
i did try to read as much as i could but apparently i didnt come across that. when i flashed to SPL 1.09, the device booted up just fine. it is when i try to update to WWE 1.10, the update process failed and bricked my phone. for your information, i was following the exact steps described by you in your unlocking/SSPL guide. you mentioned upgrade to SPL 1.09, then WWE 1.10. this is exactly what i did. i dont know what went wrong. im sure if im as knowlegable as you are, i wouldnt have screwed up my phone. my bad.
just to be fair, your method did work when i updated my dopod 595 (WWE device) to your WM6.1 beta 4 ROM. but i never upgraded my SPL to 1.10. i only thought of upgrading SPL when you posted the new radio release and that's where i screwed up.
anyway, what is important here is, is my phone unrecoverable? im reading the links you posted as i type, and i'll give the methods. maybe based on your experience, you could suggest some ways to do it. thanks.
alexnvidia said:
hi guys,
i was excited about the new Radio upgrade, so i tried to flash it. i got an error, because my SPL is 2.05. so i tried to unlock the phone using jerpelea's guide, flash to 1.09 -->success, then WWE (1.10) but an error occured saying invalid vendor ID during WWE flash. now i have SPL 1.09 on my phone and my phone is stuck on the 2nd boot screen of jerpelea's WM6.1 beta 4 ROM. my phone is fully unlocked using jerpelea's unlock guide, that's how i got to install SPL 1.09 successfully. how can i recover my phone? please help.
Update 1: i tried to flash back the original dopod 595 WM5 ROM. i mixed the RUU updater from the latest official ROM with the nbh from dopod WM5 ROM. the flashing works. when it's 100%, the phone reboots and, i got back to the same problem. stuck at 2nd/3rd boot screen. i now have IPL-0.90 and SPL 1.09 on my phone. Please help me to recover my phone. i've tried to hard SPL shown in the wiki guide, doesnt work. says invalid vendor ID crap. i really dont know what to do now.
Update 2: when the device boots, it stucks on the 2nd/3rd boot screen and if the USB cable is attached, for a brief moment, windows can detect the phone and i can even browse the content of the phone from my PC. but after that, the device disconnects itself and just remain stuck at the 2nd/3rd boot screen. the device appears to be totally freezed/hang. even the LED charging indicator will not turn off when i unplug the device from computer
i believe what i need to do now is to make a nbh image that is signed to i dont get any corrupted image message when trying to flash. i used HTC ROM editor to mix and match the SPL and IPL file so that i can downgrade the SPL to 2.05 and upgrade it again later. but i dont know how to sign nbh files.
Click to expand...
Click to collapse
run terratem
type info2
if it sais A07 then just flash rusian 1.34 rom and enerithing will be fine
application unlock it
run sspl 77.7
flash wm6.1
if it says enithing else you need to locate your original rom
till now i found that it sais a07 in most cases
BR
alexnvidia said:
i did try to read as much as i could but apparently i didnt come across that. when i flashed to SPL 1.09, the device booted up just fine. it is when i try to update to WWE 1.10, the update process failed and bricked my phone. for your information, i was following the exact steps described by you in your unlocking/SSPL guide. you mentioned upgrade to SPL 1.09, then WWE 1.10. this is exactly what i did. i dont know what went wrong. im sure if im as knowlegable as you are, i wouldnt have screwed up my phone. my bad.
just to be fair, your method did work when i updated my dopod 595 (WWE device) to your WM6.1 beta 4 ROM. but i never upgraded my SPL to 1.10. i only thought of upgrading SPL when you posted the new radio release and that's where i screwed up.
anyway, what is important here is, is my phone unrecoverable? im reading the links you posted as i type, and i'll give the methods. maybe based on your experience, you could suggest some ways to do it. thanks.
Click to expand...
Click to collapse
it depends on the info displayed on terraterm
for A07 you can use the russian rom to recover
this is what i got from terraterm. same as mtty.
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
i did flashed back to my original ROM after the first stuck in WM screen incident. and amazingly the flashing process works after several mix and match. after the original (WM5) ROM completed flashing, my IPL is downgraded back to 0.9 and SPL is still 1.09, and im still stuck at the WM logo screen (this time WM5 logo).
terraterm is a tool like mtty
what is your orignal rom??
just try to flash over sdcard... (look in wiki4more infos about that)
futureshock said:
terraterm is a tool like mtty
what is your orignal rom??
just try to flash over sdcard... (look in wiki4more infos about that)
Click to expand...
Click to collapse
i tried SD card flashing too yesterday. it says not allowed. i have already flashed over the original dopod 595 ROM and my phone is now WM5. the flashing is 100% successful, but it is still stuck at the second boot WM screen.
i think im in a really screw up position now. i have SPL 1.09 and IPL 0.9. i dont know what is corrupted now. is it the CID? SPL?
cid you can check with mtty and info 2...
if that so... just do what i have wroted in pm...
you could also just try the old htc rom (w. SPL 2.05)
futureshock said:
cid you can check with mtty and info 2...
if that so... just do what i have wroted in pm...
you could also just try the old htc rom (w. SPL 2.05)
Click to expand...
Click to collapse
both mtty and terraterm give me the same msg when i type info 2. it says time out (refer above for exact error message).
the original dopod 595 rom has SPL2.05. and it was successfully flashed into the phone. when the phone reboots, it is still stuck at 2nd boot screen (WM logo). i checked, the SPL is still 1.09, but IPL has been downgraded to 0.9.
Hi, i've bough a p3600 on ebay.
The seller tell me the phone is out because he flash a bad radio version on the phone.
I try to upgrade some file. ( Rom OS, Radio, SPL,etc ...)
I try the splexploit...
BUT ... The phone already stay on startup. i can see HTC startup screen,the windows startup screen ...but never the today screen.
I try hard reset, htc official rom, cookeed rom,...but when i flash a rom with "gsm", the update freeze at 13%
I try with usb and with sdcard..same thing, already stay at 13% !
But if i flash hard spl, 100%, if i flash OS, 100%, just the radio freeze at 13%
Any idea please ?
update
after the boot, i've got a "no gsm" message near the radio version
other people got the same problem like me ...
God oli, help me please
I more or less had the same thing and solved it with the sc card flash page.
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
A rom that works for me to flash it back to the working original
http://www.allaboutphones.nl/forum/request-originele-spv-m700-rom-p3600-rom-t727.html
To download you have to register with them.
GL
Hi, updating the radio to 1.56 crashed, now I have the No gsm message and doesn't boot, running mtty from bootloader with info2 command it says supercid but I can't update any official rom SPA, WWE, ITA... the error is "vender id invalid". I've tried the sd method but returns to bootloader .
Any help will be appreciated.
You should try SSPL : http://forum.xda-developers.com/showthread.php?t=293632
And if it doesn't work the Des' Crash-Proof SPL :
http://trinityguides.info/index.php?option=com_content&task=view&id=39&Itemid=66
and try to flash a radio rom again !
doesn't work
try again and again ...the phone block at 13% ( when the radio upgrade begin) ...
pfffff
I've the same problem and after several attempts without result I sent the phone to the workshop and they told me the problem is with the main board! (this cost almost the price of phone itself). Moreover, I've seen some where here that the problem could be caused by radio chip but I couldnt get the detail.
If you find a solution give me a tip.
i've test lot of thing.
I progress with mtty. but i've got a problem ..i can't downgrade the phone under SPL 1.05.
SPL 1.04 can "reset" the radio, or enter directly to the radio bootloader. With that, i can save my phone.
Try mmty (see the wiki => bootloader info) and with the mfg spl, you can try the method.
Guys,
I've got the same problem...
I've sim and cid unlocked my spv m700 some time ago, using wonderful software from pof. Everything went smooth.
Today I've decided to update radio rom to 1.38.00.11 to enable gps.
I've launched RUU, everything was ok till 44%, when I've got message "Communication error".
After that program tried to recover rom without success, I've got another message "Image corrupted"...
I've tried to reboot my spv (both SR and HR), after rebooting I see:
M 05
B 05 D 1.23
then those symbols disappear and I see only Orange logo.
That's it... The end...
Should I reload radio rom or both rom and radio rom to my DEAD spv? If yes - how?
Please help as I'm very disappointed, frustrated and so on!
Thank you!
Update: A-A-A!!! I did it! I revived my spv! Let me explain how (I'm kinda new to all this rom and and ssl things, so forgive me for mistakes, if there are any):
1 I ran unbrick software. Yesterday it did not work (said, that could not find smth), but today it worked fine.
2 I ran RUU and BINGO! That's it!
BTW, I have vista, but it still worked (I think, thanks to Windows Mobile Device Center, which I have installed).
Also, I killed wmd process in Task manager in the beginning (have read this recommendation somewhere).
Thanks to everybody for their help!
nyco,
could you please explain briefly what you did exactly and which radio and rom you used
thanks and regards
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Thanks stepw...
when I hit task 2A nothing happens.
Original ROM doesnt respond. I flash with cooked ones. Result 100% successful. I restart the phone- hang at boot screen.
stepw said:
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Click to expand...
Click to collapse
Hi,
I'm already under the hard SPL. and "task 2A" not working.
Macars, try only with radio ripped or full original rom (from htc or cooked with radio) because some cooked rom have only OS.
Can you tell me what SPL you have?
Hard SPL?
Have you try splxploit ?
Can you tell me what rom you try oviplokos1 ?
thanks,
it shows SPL 9.99 and with this I cannot flash anything so what I do is to update with splxploit and then the phone changes to SPL 1.2 olipro. With 1.2 I can only flash coocked ROM and will go until the end 100% successful- (original ROM the phone does not respond), but when restarts with newly loaded cooked ROM the phone hangs at window login screen and when put it in bootloader the SPL 9.99 returns again.... the story goes on like this.
I'm becoming mad....
hi,
you can only flash cooked rom because the rom you flash contains only OS. When you flash HTC rom, the rom contains os+radio+spl+....other thing ...
Try this method to downgrade your SPL (9.99) to oli 3.20 :
1°) run splxploit
2°)when the phone reboot on the spl 1.20 oli, run HardSPL 3.20 olipro. (search on the wiki or the trinity forum
3°)upgrade to 3.20 oli ...
Now, when you go to the bootloader, you can see SPL 3.20 oli.
Try reflashing a radio only (see the upgrading topic, you will see radio 1.56.xxxx)
Tell me if this method work.
When i'm on spl 3.20 oli, i can load radio rom to 0%
when I downgrade my phone to spl 1.05, and i can run the upgrading to 7% (best score )
To downgrade to SPL 1.05:
edit the "unbrick.bat" on the splxploit folder.
Replace TRIN_HardSPL.nb to TRIN_SPL105.nb
try to find SPL 1.04. I'm sure if i got the spl 1.04 i can revive the phone
Did exactly as you said final result:
When i'm on spl 3.20 oli, i can load radio rom to 0% (and stays there )
hi,
ok, try to load spl 1.05 with splxploit, and when it is load, run radio upgrade (1.56.xxxx)
Try to find spl 1.04 and mtty it can be reset the radio bootloader
if you find 1.04, give me it
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
macars said:
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
Click to expand...
Click to collapse
arf :/
You got exactly the same problem i have.
did you check if you have bad block (with mtty)
try format the phone with mtty.
i contact pof, but he doesn't answer me
Hello.
First, sorry for my bad English (French guy).
I make a SD flash with a Rom, and something strange occurs: my radio rom version change to 1.16.00.00. I try (always SD flash) to change it with a newer, the process looks good (the download bar increase, the device reboot) but the radio rom version always the same. I try to change OS rom, no problem. I try to change SPL version, impossible: all process executed without error but at the next load of SPL (power-camera-reset) the version is always the same (1.30 Olipro).
I try with another computer (Win XP pro SP2) and with activSync, the problem was the same !
And I try with several rom version, idem.
So to be quick
OS ROM change: no problem
SPL change: impossible
Radio ROM change: impossible
If someone have an idea, I will be very happy
Bye
I find the solution !
Usually, I toogle in SPL mode manually.
The soluce for me was to downgrade the SPL (1.30 to 1.20 olipro) but let the RUU launch is own SPL.
And after, the SPL version was 1.20 and I can change ROM, Radio ROM etc...
[Mode happy ON]
Bye
Hi, can you post the procedure please? I have the same problem!!!
But your pda statup?
Thx
Roby
i don't understand how that is accomplished.
i have read through the trinity guide and that is what they recommended
My trinity has been flashed with 1.3oli and a custom rom but it hangs at the start up page.This makes the device disconnect from the USB.
so how do i let the RUU launch its own SPL?
It is supposed to make the device go into bootloader right? i cant access that since it is hanged
Advice please
Hi bigrockshow,
it is impossible, in this condition that rru launch its SSPL, and it is ipossible to use the method sspl.exe ....
I think that the only way is the splxploit but I don't find a sspl file to load on p3600 with splxploit
anyone have it?
I've exactly the same problem, oli 1.30, I can flash OS roms with no problem but I can't get a radio rom to go past 0%.
I've tried the spl exploit to boot into spl 1.07, I've tried going into the bootloader manually and I've tried letting the RUU load the SPL, no matter what I do I can't shift the radio from 1.16?
Any ideas?
mine is just wierd...
i used SPLxploit and the spl jumps to 3.03...
tried to flash hard SPL and its has error 270...
so i did SPLxploit again...
shows SPL 1.20 now
Tried to flash another rom and it still doesnt work..
did i miss something or is my dopod screwed...
You can't upgrade to the 1.56.70.11 Radio with Olipro 1.3. It looks like it's worked and gets to 100% on mine but doesn't actually change anything. I ended up using another HardSPL (can't remember the name now) to get the 1.56.70.11 Radio on there.
I looked for ages for a version of Olipro 1.2 but couldn't find one anywhere. Apparently it works ok with that version.
Sometimes these threads are really hard to follow when they get massive and the author updates the first posts and over writes stuff. I think they should all keep old stuff in there and just add too it instead of replacing information.
To all,
I had the 1.14 spl olinex and installed the new 1.56.00.00 release of original italian rom.
I had the green screen as everyone knows, so I installed again the spl from original htc (not the unsigned).
Than my phone always starts with the bootloader and doesn't go on. Giving upgrade rom error.
Please help me!!!!!!!!!!
Pietrona said:
To all,
I had the 1.14 spl olinex and installed the new 1.56.00.00 release of original italian rom.
I had the green screen as everyone knows, so I installed again the spl from original htc (not the unsigned).
Than my phone always starts with the bootloader and doesn't go on. Giving upgrade rom error.
Please help me!!!!!!!!!!
Click to expand...
Click to collapse
Flash your stock ROM via the bootloader.
upgrade your rom using BLACIMG.nbh <-- stock ROM.
make sure you choose a MicroSD that you know it works for sure (like sandisk).
that's no brick yet.
copy your ROM file and rename to BLACIMG.nbh and save it in the root directory of your storage card. Plug it in to the phone again and hold VolDn + press Power button to start the flashing process.
If it's really bricked you wouldn't even able to see the SPL splash screen...
THANKS
Dear all,
great persons......you are.
Thanks for answers, but after 3 hours getting crazy I downloaded the original rom and everything goes right............
Thanks all
hehe you wana sell that brick?