Related
my T-Wings give me WIFI problums coz i always Conact WIFI network on my work place but mostly time wifi show its conncted but not working .. but after reset some time its work or some time not
some1 know whtz wrong ?
maliks said:
my T-Wings give me WIFI problums coz i always Conact WIFI network on my work place but mostly time wifi show its conncted but not working .. but after reset some time its work or some time not
some1 know whtz wrong ?
Click to expand...
Click to collapse
have you tried accessing any other wifi connection outside of your workplace ? does it give you the same problem ?
Wifi problums
yes but i didnt face problum other places but on work place its working befor fine
problem with T MOBLE WING
I have the same problem , I even did try connect to my home Wifi it show connected ,but doesn't open to the website I want to ,can some one help,thanks
I had the same problem, I installed batterystatus, and checked the option to disable gprs when wlan is on, and now it works fine...
You don't need batterystatus to do this (the software just does it automatically for you), you can do it by yourself by disabling "data connection" in the connection manager whenever you turn on the wifi radio
-Hope it helps
t-mobile wing wifi problems
I had a similar problem with my wing. It would connect to unsecured WIFI networks and work flawlessly but when I connect to a secured network it would work for about 1 min then just hang while downloading a web page. If you device is doing this send it back to t-mobile and get a new one. This is what I had to do. hopefully you have a warranty.
I just got my T-Mobile Wing and I think I have the same problem. It just doesn't want to work with my WPA-secured Wi-Fi. When I switch WPA off, it works fine.
Did anyone else had a problem like this?
Called T-Mobile, they have nothing like that in their knowledge base.
I got this problem when i installed HTC 10 Button comm manager. I uninstalled it and WiFi works again.
Hope this helps
i have somewht of a similar problem, since ive had my Wing i have been unable to use my wi-fi, when i turn it on it says connected and shows me the lil meter and everythin but when i try browsing or downloadin it just hangs and does nothing until i turn the wi-fi off...i have no clue why i have learned to live without it but would appreciate any help...thanks
Try this it work for me. Whenever you want to connect to secure wpa do this before you make the connection
Start > Setting > Connections > Wifi Status > Power Mode > Move the slide "Best Performance"
Your wing should be able to connect to secure wpa.
Hope this help.
timace said:
i have somewht of a similar problem, since ive had my Wing i have been unable to use my wi-fi, when i turn it on it says connected and shows me the lil meter and everythin but when i try browsing or downloadin it just hangs and does nothing until i turn the wi-fi off...i have no clue why i have learned to live without it but would appreciate any help...thanks
Click to expand...
Click to collapse
Make sure you disconnect from edge/gprs before you try to surf after you are connected to the wifi.
ivanmmj said:
Make sure you disconnect from edge/gprs before you try to surf after you are connected to the wifi.
Click to expand...
Click to collapse
how exactly do i do this? is it what was explained about in the battery status menu and check marking the box 'disable proxy for wi-fi'...?
You can click on the little E or G on top and click on Disconnect.
ivanmmj said:
You can click on the little E or G on top and click on Disconnect.
Click to expand...
Click to collapse
i dont know how i ever survived without wi-fi....WOW....thank u
Thank Ayodeji13. He answered this in the 5th post. ^_^ But, yea, I've done the same thing before and was lucky to realize where the problem was coming from. Unfortunately, it didn't help me with the crappy wifi signal that my Wizard provided me. The wing, on the other hand, is MUCH better at this.
joking said:
Try this it work for me. Whenever you want to connect to secure wpa do this before you make the connection
Start > Setting > Connections > Wifi Status > Power Mode > Move the slide "Best Performance"
Your wing should be able to connect to secure wpa.
Hope this help.
Click to expand...
Click to collapse
Thanks mate... I too was having issues connecting to wifi... its kind of strange... it was connecting to my home network for sometime but later it suddenly stopped. It will connect to other networks but not to my secured network. Today I tried the setting you mentioned and surprisingly my phone connected to my home network... I wonder why because this setting should improve the performance and not the connectivity itself... Thanks again
you can add me to the list of people with wifi issues. I can't connect to my wireless router and I'm stand two feet away from it. It shows up but when I try to connect it says unavailable. I've done everything from turning the data off, to setting the power to best performance but it won't connect.
I need help... Whenever I connect it says I'm connected but actually I'm not. Yesterday I could view directions using live search but couldnt browse the web, not i cant do both. it gets stuck on the locating... part of loading the website. sometimes it gets to opening but the KB bar doesnt come up and it gives me some 500 internal error, or page doesn't exist. I cant do the best performance thing because im using touch it 2.3 rom and i dont have wifi status anymore.
WHY DO YOU HAVE TO REMOVE THAT STUF?!! URGH! I dont even have msn!
But anyways, can someone help me connect to the internet?...
TRY THIS
I have the same problem, i i manage to fix my wifi connectivity by editing the registry.....try this at your own risk.....but swear it works for me. i used total commander to edit registry and go to:
HKEY_LOCAL_MACHINE > SOFTWARE > HTC > Comm Manager >
then you will see folders 0 - 8 or some only have 0 - 7 ,delete folders 6 and up ........ ( I JUST MOVE MINE instead of DELETING IT< I MOVE IT TO STORAGE CARD SO IF SOMETHIN GOFF UP I CAN JUST PUT IT BACK )....
SOFT RESET then try turn your wifi ON , connect to your network.... til me if this works for u guys...
i think the value of those folders are bum hehehehe thats why it wont connect......., after connecting to your wifi secured or not , it will create another folder and add those folders back by default...but this time the good settings lolz its worth a try !
Ok this is realy frustrating. My wing was getting on my secured home network and npw it dose not. I read all the post and have tried some (the ones that I could understand). I dont have the option under battery status to disable gspr or gpsr. And my system is vista 64 so total commder dosen seem to work for reg settings(edits). I can conect to unsecure networks but I cant to my hone (secure) network. I have in the past but it dsent ssem to work now?
Every time I do a soft reset, I get a notification bubble
Connection Setup
The operator does not exist in the data base. Please contact your operator for connection settings
The connection Setup will redirect you to the connections screen. (Very annoying)
Once I hide the notification I get redirected to:
Settings/connections screen I just hit ok in the top right corner to get rid off it.
The phone finds my network without any problems (Rogers Canada) it just can find the operator trough connection setup I guess?
I have an unbranded Tytn II the Connection Setup version 1.0 (build 30726.ppc.001) doesn’t have Canada as a choice to select Operator.
Can I disable connection setup? If so how? Or can I add Canada Rogers as an operator and how ?
Thanks in advance
PS I did searched the 12 pages result from connection setup
in settings\connections
goto connection setup
right softkey
uncheck "enable auto configuration"
that would turn off the detection everytime you turn on the phone
and about settings, coz i'm in fido, so i can't help you with that
badghost said:
in settings\connections
goto connection setup
right softkey
uncheck "enable auto configuration"
that would turn off the detection everytime you turn on the phone
and about settings, coz i'm in fido, so i can't help you with that
Click to expand...
Click to collapse
I have the auto configuration uncheck but sill doest it I am wondering if I can uninstall connection setup
hmm i'm with fido and everytime i used to get that same message...after unchecking it..and soft reset it never came back..not too sure why it doesnt work for u
PS. i do have canada and rogers in my drop down lists
i have version 1.0 build 31261<PPC.020>
which one do u have?
bapssystupr3m3 said:
hmm i'm with fido and everytime i used to get that same message...after unchecking it..and soft reset it never came back..not too sure why it doesnt work for u
PS. i do have canada and rogers in my drop down lists
i have version 1.0 build 31261<PPC.020>
which one do u have?
Click to expand...
Click to collapse
I forgot to reset my phone Now its working Thanks a lot boys
I don't have rogers on my drop list it may be because I am still using original rom I see you have dutty rom he may load it.
yup to soft reset...glad to hear its fixed for u now.have fun
Hi all,
I would like to ask you all, if anybody knows a software that could at some specific point save current GPS location and Current WiFi connected network signal strength? I tryed ministubmler but it hust doesnt work. i need this for kaiser phone.
ivugrinec said:
Hi all,
I would like to ask you all, if anybody knows a software that could at some specific point save current GPS location and Current WiFi connected network signal strength? I tryed ministubmler but it hust doesnt work. i need this for kaiser phone.
Click to expand...
Click to collapse
you can use WifiFoFum
Personally, I like AiroMap, but WifiFoFum does work too.
AiroMap does not work on my kaiser
Can you confirm that AiroMap works on kaiser? I tryed that but it just shows Yellow question mark warning. Also, there is no hardware device to select in drop down menu.
ivugrinec said:
Can you confirm that AiroMap works on kaiser? I tryed that but it just shows Yellow question mark warning. Also, there is no hardware device to select in drop down menu.
Click to expand...
Click to collapse
I wouldn't have said so otherwise... Triangle means WiFi isn't turned on I believe.
A strange problem..
I recently got GPRS activated on my sim..
When i try connecting on my Diamond, the E becomes active and it tries to connect.. But after abt 30 secs to a min, it says "Cannot connect for an unknown reason... etc etc.."
I initially thought it was a problem with the network..
But, when i put the same sim in my old Asus P525, set up the connection and tried to connect, the G became active and got connected within a few seconds!!!
From then i've been tryin to connect on my Diamond and have got connected about twice with E in the signal bar.. But that must've been some freak accident cos after a few hours i tried connecting w/o changing any of the settings and absolutely no luck!
I've tried almost all the cooked ROM's. And different radios.
Right now i'm on the Official WWE ROM 1.93.
Hard SPL 1.23 or 1.24.
And 1.00.25.03 Radio.
Any idea about what's wrong, guys?
Make sure you have the correct GPRS/WAP settings installed on your HTC Diamond.
There are different settings for Payandgo and Contract SIM cards.
You can try searching Google for them, or if you live in the UK try this website: http://www.filesaveas.com/gprs.html
prank1 said:
Make sure you have the correct GPRS/WAP settings installed on your HTC Diamond.
There are different settings for Payandgo and Contract SIM cards.
You can try searching Google for them, or if you live in the UK try this website: http://www.filesaveas.com/gprs.html
Click to expand...
Click to collapse
prank1, the settings are right..
That's why it's working on my old phone..
I think it may have somethin to do with Edge and GPRS..
Maybe my service provider does not have Edge capabilities..
If i'm able to restrict my Diamond to try and connect to Edge and connect to GPRS instead, it may work..
Any way that could be done?
sanctifiedrust said:
A strange problem..
I recently got GPRS activated on my sim..
When i try connecting on my Diamond, the E becomes active and it tries to connect.. But after abt 30 secs to a min, it says "Cannot connect for an unknown reason... etc etc.."
I initially thought it was a problem with the network..
But, when i put the same sim in my old Asus P525, set up the connection and tried to connect, the G became active and got connected within a few seconds!!!
From then i've been tryin to connect on my Diamond and have got connected about twice with E in the signal bar.. But that must've been some freak accident cos after a few hours i tried connecting w/o changing any of the settings and absolutely no luck!
I've tried almost all the cooked ROM's. And different radios.
Right now i'm on the Official WWE ROM 1.93.
Hard SPL 1.23 or 1.24.
And 1.00.25.03 Radio.
Any idea about what's wrong, guys?
Click to expand...
Click to collapse
My bad - didnt see the 'set up connection' bit so I assumed you didnt have the correct settings.
I had this problem once but it went away with a ROM upgrade - that was when I had the XDA Orbit.
The problem may be that my phone does not try connecting to GPRS and directly tries to connect Edge..
Isn't the connection supposed to be G-E-3G, in that order?
Is there any way i can prevent my phone tryin to connect to Edge?
Can i make GPRS as first preference instead?
Anybody? Please?
From what i heard my diamond doesn't support US( or Canada which is where i live) 3g because of diamonds hardware so that's why it only connects to edge which is really slow... anyways to connect i had to phone rogers my wireless provider and they gave me my username and password which was needed to connect online. So i'm guessing it's the same for you if you go to
Settings > Connections > rogers internet( for mine) > Manage existing connection
from there you'll go to the next page where you can input your info.
NekciuQ said:
From what i heard my diamond doesn't support US( or Canada which is where i live) 3g because of diamonds hardware so that's why it only connects to edge which is really slow... anyways to connect i had to phone rogers my wireless provider and they gave me my username and password which was needed to connect online. So i'm guessing it's the same for you if you go to
Settings > Connections > rogers internet( for mine) > Manage existing connection
from there you'll go to the next page where you can input your info.
Click to expand...
Click to collapse
Hey.. That doesn't seem to be the prob since i can get it to work on my old PDA with the same settings..
That phone gets connected and it shows 'G'.
What might help me is somethin to block my phone tryin to connect to Edge before it even tries to connect to GPRS..
I don't think that's practical, but wishful thinking..
I've had the same issue with my Diamond, I know for sure that the network settings are correct as it sometime connects fine and other times I keep getting the "Cannot connect for an unknown reason..." error- only a soft reset would resolve the issue. Seems a bit random but am trying to monitor what is causing it.
It always used to work fine on my Hermes. BTW I'm using Dutty's ROM on my Diamond.
sh500 said:
I've had the same issue with my Diamond, I know for sure that the network settings are correct as it sometime connects fine and other times I keep getting the "Cannot connect for an unknown reason..." error- only a soft reset would resolve the issue. Seems a bit random but am trying to monitor what is causing it.
It always used to work fine on my Hermes. BTW I'm using Dutty's ROM on my Diamond.
Click to expand...
Click to collapse
Yeah.. Sounds almost like my prob..
Could it be a rare manufacturing defect sort of thing thats affecting our phones?
Cos nobody else seems to have such an issue..
And i keep changing between Dutty's and Panosha's ROM..
I don't know if it's same problem you have ,
but I had kinda same problem..
I found that the lame ActiveSync change the proxy of my internet connection and put in the internet connection proxy my local proxy at work, even I removed the proxy it didn't help (dunno why) , just by adding new connection from the advance and adding new name etc.. it solve the problem...
sanctifiedrust said:
And i keep changing between Dutty's and Panosha's ROM..
Click to expand...
Click to collapse
I've only had my Diamond (MDA Compact IV) for only about 3-4 weeks. I was so keen to flash to a different ROM that I did so within 10-15 hours of receiving the device; my point being that I didn't get to try out my data connection on the stock T-Mobile ROM.
The connection seems to be fine today...!
arix said:
I don't know if it's same problem you have ,
but I had kinda same problem..
I found that the lame ActiveSync change the proxy of my internet connection and put in the internet connection proxy my local proxy at work, even I removed the proxy it didn't help (dunno why) , just by adding new connection from the advance and adding new name etc.. it solve the problem...
Click to expand...
Click to collapse
Hmmm.. I don't think i have the exact same problem, but somethin similar..
I'll try adding a new connection..
Thanx..
As I know something with Activesync **** the GPRS connection..
Let us know if you solve your problem with new connection...
Ok.. Note the "E" in the first pic and in the second..
The first one is 'clear' and the second one is 'hazy'!
When the "E" is 'clear', my GPRS connects!!!
I found this out after putting a different sim card of a different network and connecting..
When i put the other sim card, i got 'clear' "E" and GPRS worked..
Then i put back my old sim card and on switching on the phone, the "E" was still 'clear'!!
On tryin to connect, it worked!!!! Even after several manual diconnections, it worked only cos the "E" was still 'clear'..
Then i reset my phone with my sim card and got the 'hazy' "E".. And back to square one.. Not connecting..
My question is, what does this 'hazy' "E" mean and how do i make it 'clear'???! Only then my GPRS seem to work!
Help!!!!!!
This is how it is when connected properly..
Cannot connect for an unknown reason
I also had this problem. To make my story short, I have a data plan with Claro Peru which I have been using with my Touch (not 3G phone) with no problems. 3 days ago I acquired my Diamond 3G US version. When attempted to connect to the HSDPA I got the error mentioned here (cannot connect for..., sometimes the "H" symbol was difusse [like in the picture in a previous post in this thread], etc). The root cause of this was that my data plan only have GPRS/EDGE activated, my network provider (Claro) differentiates 2G internet vs 3G (so no HSDPA/UMTS until subscribing to a new plan).
The **SOLUTION** for my case was to select under "Select your network type" the option GSM (Start, Settings, Phone, Band tap). The option Auto was the default. Thus restricting to EDGE my data connection (which is according to my plan). Also, on the same tap I selected UMTS(850+1900)+GSM(850+1900) under "Select you GSM/UMTS band". You have to select here the frequencies according to your country.
P.S. The problem was the same before and after I updagred my ROM to RUU_Diamond_HTC_WWE_2.03.405.3_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship. So, two things to mention here. 1, A ROM upgrade is not the solution for this problem (in my case). 2, you can upgrade the Diamond US version (my is DIAM110) with a WWE ROM upgrade.
Hope this help someone.
dach said:
I also had this problem. To make my story short, I have a data plan with Claro Peru which I have been using with my Touch (not 3G phone) with no problems. 3 days ago I acquired my Diamond 3G US version. When attempted to connect to the HSDPA I got the error mentioned here (cannot connect for..., sometimes the "H" symbol was difusse [like in the picture in a previous post in this thread], etc). The root cause of this was that my data plan only have GPRS/EDGE activated, my network provider (Claro) differentiates 2G internet vs 3G (so no HSDPA/UMTS until subscribing to a new plan).
The **SOLUTION** for my case was to select under "Select your network type" the option GSM (Start, Settings, Phone, Band tap). The option Auto was the default. Thus restricting to EDGE my data connection (which is according to my plan). Also, on the same tap I selected UMTS(850+1900)+GSM(850+1900) under "Select you GSM/UMTS band". You have to select here the frequencies according to your country.
P.S. The problem was the same before and after I updagred my ROM to RUU_Diamond_HTC_WWE_2.03.405.3_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship. So, two things to mention here. 1, A ROM upgrade is not the solution for this problem (in my case). 2, you can upgrade the Diamond US version (my is DIAM110) with a WWE ROM upgrade.
Hope this help someone.
Click to expand...
Click to collapse
I have the Diamond on T-Mobile in the UK with the web'n'walk plan (HSDPA enabled - although not the higher-speed "plus" version). This happens to me every single time I'm in a GPRS-only area - when I have HSDPA coverage, it connects fine. In order to get it to connect, I have to open the Comm Manager, turn off the data connection and re-activate it.
Before anyone asks, my connection settings are all correct and I've tried numerous different main and radio ROMs - nothing makes a difference. I'll give this a shot, see if it makes a difference.
BLCollier said:
I have the Diamond on T-Mobile in the UK with the web'n'walk plan (HSDPA enabled - although not the higher-speed "plus" version). This happens to me every single time I'm in a GPRS-only area - when I have HSDPA coverage, it connects fine. In order to get it to connect, I have to open the Comm Manager, turn off the data connection and re-activate it.
Before anyone asks, my connection settings are all correct and I've tried numerous different main and radio ROMs - nothing makes a difference. I'll give this a shot, see if it makes a difference.
Click to expand...
Click to collapse
OK, I would try the option Auto for the "Select your network type" so the phone auto negotiates the technology in use (between GPRS or the much better HSDPA), but change the option for the bands according to your country.
Let us know the results!
Morning all
I have unlocked my phone with htc-unlocks.com and works well but I keep getting this error when I switch my phone on.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Connection Setup
The operator does not exit in the database.
Please contact your operator for the connection settings
Connection Setup will redirect you to the connection screen
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
How do I get rid of this?????
rustyj said:
Morning all
I have unlocked my phone with htc-unlocks.com and works well but I keep getting this error when I switch my phone on.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Connection Setup
The operator does not exit in the database.
Please contact your operator for the connection settings
Connection Setup will redirect you to the connection screen
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
How do I get rid of this?????
Click to expand...
Click to collapse
I'm not sure if this will work, but have you tried going to Settings\Personal\Phone\Network and then try to Find Network and Set Networks. Once you find your network provider, you can then try Settings\Connections\Connection setup and in Menu, select Update Database.
Has this issue been resolved?
I had this issue when I bought an unlocked phone from the UK. It was on stock 1.19.61.1 WWE , I flashed to "L26_THD V3.55_WWE_Ultimate" and no longer had the problem.
Connection setup
Hi Ya
I did as ClydeB1 advised but I only have Orange to select as an operator ???
If I do flash my phone with "L26_THD V3.55_WWE_Ultimate" can I still get updates from HTC's website?? Or has my phone officially moved to the dark side once I flashed it??
Thansk for the advice guys