Related
Hi,
Thanks to the very clever people over at www.imei-check.co.uk I now have an unlocked T-Mobile Vario.
http://www.imei-check.co.uk/m3000unlock.php
I now wish to know if I can flash my unlocked Wizard with an Imate K-Jam2 flash?
I know there is another post on flashing the the Qtek 9100 with the K-Jam but I dont know if the T-Mobile Vario will pose any different issues or problems.
What I want to know is :-
1) Can it be done, can I flash my T-Mobile Vario with a K-Jam2 ROM?
2) How do I make a backup of my T-Mobile ROM before taking the plunge?
I am a Sony Ericsson P900 convert so please be gentle with me on your responses. I'm no expert but have got this far (Unlocked) by reading these and other forums.
If any of you can help out I would be most gratefull.
Cheers
Lee
I have (had) a Vario from T-Mobile Netherlands. I unlocked like you and ran the ROM upgrade utility for Qtek 9100, available for download on :-
http://www.beyondthetech.com/blogs/kjam/
It works fine. My Dutch phone now talks to me in English.... phew!
@belgilux
What are the advanges of the qtek rom over the vario ??
Niets dat ik kan bespeuren. Enkel is ding dat zijn in WWE - wereld Wijde Engels - dit is good voor mij aangezien mijn Nederlands niet zo goed is. ..
ok thanks ,
mijn nederlands is goed , dus hou hem liever in nederlands
grtx, arnold
Hey, guys, I have the same problem - I want to change the OS from a german to en english one. My device is the XDA Mini S from O2 Germany. Do I *really* need to pay for unlocking first or I can just flash it?
P.S. How did you back up the ROM before the flashing?
hello ingenious ,
as far as i know , you have to unlock it first otherwise you can't acces the bootloader.
buckup of your old rom can be done (only after unlocking).
you need the program romupdate.exe
disable activesync on usb connection
turn off phone
connect usb cable while pressing camera button
start romupdate
chooice usb connection
enter 'r2sd all' this coppies your phone rom to your sd card (sd card will be erased !!!!!)
next step is to dump the sd card to file to store.
you need ntrw.exe and sd card reader
in a dos box in a dir with ntrw enter 'ntrw read dump.nb1 drive_letter_of_reader:'
that will dump you entire sd card to file.
to restore , but it back with ntrw write .......
reset phone while holding voice an camera button and chooise restore from sd card.
good luck , arnold
p.s. i'm wrinting this out of my memory so forgive me if i have something wrong.
Hey, thanks very much
Just a thing bothers me still... If I unlock the phone (i.e. replace the boot loader) won't I just lose my warranty from O2?
mhh that doesn't worry me to much,
officiali it will only void your warrnaty if they can proof that that is the problem.
if not they can not hold it against you (in holland that is) , but you may have to 'fight' for your warranty.
grtx , arnold
run the ROM upgrade utility for Qtek 9100
hi guys,
i wanna ask a questions about run the ROM upgrade from utility for Qtek 9100.
my pda-phone is mda vario, is it possible if i did it without unlock my phone?
because i tried run the ROM upgrade utility for Qtek 9100, but it said that there is an error with my phone while in process. but in that case, i haven't unlocked my phone.
anyone can help me, please
thank u...
reset phone while holding voice an comm.manger button and chooise restore from sd card.
Click to expand...
Click to collapse
but he boot NOT from the sd card ... where is the trick ?
regards
I have successfully replaced the ROM on my MDA Vario with a K-Jam ROM and now I want to go back to the original ROM. Following the instructions by arnoldl earlier in this thread I created a backup dump.nb1 file and used ntrw_189.exe in a CMD window to dump this to a file. This took bloomin' ages since I have a 1GB card - very tiresome!
Anyway, I have now reversed that process to copy the dump file back to the mini-SD card but when I hard reset my Vario I do not get a prompt to restore from the SD card. I only have options to restore to original settings or cancel.
I have allowed a hard reset to complete and the mini-SD card does not even register in the Vario. Removing and reinserting does nothing. I've tried a hard reset twice and still no joy.
Assuming I have successfully created a working ROM image on my mini-SD card are there any other tips or options for restoring it to the Vario ROM?
anyone knows the keys to press for restore an image from sd card ?
I have tried all combinatiosn of keys, but nothing are working
regards
sorry , it is hold camera and voice comm button while resetting.
previes state must be on!!
grtx arnold
Thanks for that. I just realised it says hold camera and voice comm rather than comms and voice comm, like you would normally do for a hard reset.
I've tried a boot with the correct buttons and could see nothing at all on the screen. I now realise there is something but without a backlight it is nigh on impossible to see. Anyway, I spotted that too late and started button mashing to try to get the thing to spring into life. It is now staring at me with a big clear white (lit) screen that dims briefly periodically. I now have no idea what is going on and whether this is the correct behaviour or not.
How long should the reflash take? Will having a 1GB card mean it takes 8 times as long as a 128MB card as it has to read the whole thing? How do I know if this is working OK?There are no progress bars or anything - just a plain white screen.
i did say comm and voice , but i just changed that
reflash was prety fast when i did it , within a minute i thought (256mb)
Oh dear :-( Mine's been blinking at me for 15 minutes now.
I just restarted the process and I managed to see a "Format BinFS Success" message and a progress bar at the bottom which I think said "Upload OS" or something like that - too difficult to read properly in today's miserable grey daylight. But I'm now staring at the plain white screen once more.
Maybe my ROM image is fried. Any ideas how to get hold of a clean T-Mobile UK MDA Vario ROM file?
EDIT : Further info......
Bored of the blank white screen I pressed the reset button on its own. The device reset and this time with the benefit of the backlight being on I could see the Format BinFS success message, a couple of checksum checks and something about downloading ROM and extended ROM. This all took only a minute or two, which seems positive. But then I saw a message about formatting FAT (or FAT32?) and while that was being displayed the screen faded/disolved to plain white and has resumed its periodic dimming.
Unfortunately I now have HTC Innovation and imate branding all over the thing so I can't just pop it back to T-Mobile to fix it. I wish they had a full ROM upgrade/replace image in a .exe, like qtek and imate.
hello,
what means "previes state must be on!! "
i have an 512 mb card and no chance to boot the sd. Has anyone
try the qtek german bin on the xda ftp server here ? i write this
image via ntrw on my 512 mb card, press the camera and voice button and also reset, but the sd card want recognize ...
help! I want this german qtek rom on my wizard.
regards
greddy said:
hello,
what means "previes state must be on!! "
Click to expand...
Click to collapse
i only got in this mode when resetting with the buttons pressed when phone was on.
when i first shut it down and then reset it didn't work.
grtx
Having left the white screen for a couple of hours there is no sign of anything useful happening. I reset the device and now I am dumped directly to the bootloader screen - there seems to be no software on the device now.
So it appears I can only get this thing up and running again with the k-jam ROM (or presumably Qtek) by running the .exe ROM upgrade file. But for me my option to go back to native Vario software seems to have vanished forever. Maybe I'm just really unlucky but this might serve as a warning/caution for others who want to flash their Vario.
Hi friends,
I am very new to upgrading\downgrading pc phones. I was trying to upgrade my wizard to upload diffirent language ROM, using this method :-
http://forum.xda-developers.com/viewtopic.php?t=56088
After some tries, I succeeded to upgrade rom, but after this power on the wizard and it stuck into startup screen.
If I press Camera + Power swich it shows three colour screen and some text :
IPL 2.16. 0001
SPL 2.16 0001
I think my device was CID locked and G4, and that is why I have a dead wizard.
I have backed up the phone before upgrading with wizBackup.exe and I have back files on my hard disk. I dont know how to restore rom from these backup files. :?: :?: :?:
Please help me to revive my PC.
Thanks in advance
Singh06 said:
Hi friends,
I am very new to upgrading\downgrading pc phones. I was trying to upgrade my wizard to upload diffirent language ROM, using this method :-
http://forum.xda-developers.com/viewtopic.php?t=56088
After some tries, I succeeded to upgrade rom, but after this power on the wizard and it stuck into startup screen.
If I press Camera + Power swich it shows three colour screen and some text :
IPL 2.16. 0001
SPL 2.16 0001
I think my device was CID locked and G4, and that is why I have a dead wizard.
I have backed up the phone before upgrading with wizBackup.exe and I have back files on my hard disk. I dont know how to restore rom from these backup files. :?: :?: :?:
Please help me to revive my PC.
Thanks in advance
Click to expand...
Click to collapse
Your phone is not dead!!!
If you can get to the three color sceen then your botloader is intact (and preserving the bootloader was the point with the tutorial that you followed).
Your phone is CID locked and is G4, that's right, but this is NOT the reason for the problem. The tutorial you followed, which incidentally I wrote, deals with CID locked G4 phone like yours.
The problem you had is probably due to a not correctly cooked rom.
Anyway, don't worry. You got the three colors screen so you can connect your phone to USB (even if activesync won't recognise it) and flash your factory rom (the one you were trying to replace). Don't need to use your backup: simply download the original rom from the manufacturer/operator site.
bye
After many tries now my phone is working again,
I downloaded RUU_Prodigy_2170702_21707102_20710_QTEK_WWE_Ship from internet then cooked its nk.nbf file.
then uploaded the rom and phone is working again. Thanks for your help
Singh06 said:
After many tries now my phone is working again,
I downloaded RUU_Prodigy_2170702_21707102_20710_QTEK_WWE_Ship from internet then cooked its nk.nbf file.
then uploaded the rom and phone is working again. Thanks for your help
Click to expand...
Click to collapse
I glad you worked it out!
Bye
hello. I have similar problem. I upgraded my wizard to AKU2.3 and now phone doesn't start. It start showing splash screen with the information:
IPL:2.24
SPL:2.24
GSM:02.25.11
OS:2.24.10.1
HOW to fix this problem ?
hi guys
i have qtek wiza200 today i'm use MrClean_RUU_WIZARD_224a_AKU23_WWE.zip after flashing my phone turn on and installing all soft and restart and dead my phone. i'm push camera+power+reset i can't enter to boot mode. help me to repair my cellphone and how resolve my problem. my phone forever dead????
thanks a lot
Hi all,
I tried to upgrade my MDA compact II (HTC Charmer) to WM6, but during the first step, downgrading to the "no vendor" version I made a mistake. A used a wrong version, it was for Prophet. After the final reboot, the device froze in the splashscreen "T-Mobile". After that I tried to do exactly the same with a "Charmer" version, but it didn't help me, the situation was the same.
However, now I'm able to flash successfully only the last vendor provided ROM update "RUU_Compact_ll_2060227_20602110_021921_T-MobileUK_Ship.exe", but it doesn't help me anyway, my Charmer is still freezing in the splashscreen. I tried to downgrade it , but the application gives the following error: "UPGRADE ONLY". When I try to make a hard-reset, and after that to confirm the factory settings by pressing "Yes" (green) button, the result is "Format FAT partition" and then "format is failed".
Only the bootloader is working now as well as the battery charging. Please, help me to turn back to the life my Charmer!
And one additional question: can I perform a CID unlocking just by ROM-flashing or the device must be fully operable?
Flash this:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
After that, you should be able to make hard reset. If you succeed, flash "RUU_Compact_ll_2060227_20602110_021921_T-MobileUK_Ship.exe" - that.
Hello there,
I am a new use an recently got an MDA PM200. I am in exactly the same situation as petrun. I have tried the flash suggested by vlodeck but it doesn't work, saying incorrect vendor ID (I guess that's because it's for a Prophet?).
What should I do next...?
Thanks.
OK, I succeed with a little progress. Many thanks to vlodeck, I will try to explain what happend...
I successfully flashed my Charmer with this Prophet ROM:
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
Full link:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
But it was possible only by using this "No ID" update application, not original one, maybe because my device is still locked:
Full link:
http://www.windowsceportal.hu/tartalom/programok/htc_charmer_upgradeut_noid.zip
After that I succeed to format the FAT partition (finally ). But I cannot after all to flash the latest official MDA compact II firmware. There is two possible events, which I experienced:
1. When I try to use the original flashing application, I get the following response: "UPGRADE ONLY".
2. When I try to flash the official MDA compact II ROM, but through the "No ID" application, I get "INVALID COMMAND".
Just for explication, now my device cannot boot, it freezes in the splashscreen (it is Qtek now, not T_Mobile...) and the following versions could be read:
IPL 2.06
SPL 2.20.0000
GSM 02.47.21
OS 2.20.7.34
So, how I can do that? What should I do further? I would like to unlock my Charmer, but should I firstly make it operable?
Thanks in advance for your help, guys!
By the way, all described above I tried sevetal times with the same result.
The other thing is that... all links about the CID unlocking downloads, which I found here are no longer active. Any alternatives?
Rise from the dead!
Incredibly, but it's a fact! After successfull FAT formating I probably didn't wait long enough. Today I turned on my Charmer and several seconds after the splashscreen "QTEK" it successffully booted in WM5, performed all settings and finally started to work!
It's GSM module works, the Bluetooth works, I am able to start different applications. Just the camera does not work. And the most strange thing for me is that this ROM was for Prophet, not for Charmer
So, after all, how to proceed to upgrade to WM6? Now the bootloader is above ver.2.
Should I firstly flash it with proper ROM (for Charmer) or it's not necessary?
Should I unlock it as is now (Prophet ROM)?
Vlodeck, I rely mostly on you, since the WM6 with Touch FLO is your creation.
Thanks!
You dont have to CID unlock. Just flash that WWE T-mobile WM5 AKU2 for Charmer. Good luck.
Maybe I am boring, but steel need an advice: I cannot flash "WWE T-mobile WM5 AKU2".
1. The original RUU gives me "UPGRADE ONLY", maybe because my SPL after flashing the Prophet ROM is 2.20
2. This "NO ID RUU":
http://www.windowsceportal.hu/tartalom/programok/htc_charmer_upgradeut_noid.zip
reaches 2% and gives "INVALID COMMAND", after that - only bootloader screen.
3. This "NO ID RUU":
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
cannot open the nk.nbf image (but works with other images), I don't know why.
What is the solution? Any ideas? Maybe some tool to downgrade the SPL to ver.1? I tried (it perhaps was bad idea)"RUU_Charmer_1120223_11202110_11220_T-MobileUK_Ship" and IPL became 1.12, but SPL remained 2.20... and Charmer didn't boot after that. After flashing the Prophet ROM it works again and IPL is 1.12, SPL is 2.20
In brief... how to flash successfully the last Charmer ROM?
If you cant flash the AKU 2 charmer rom, then go for AKU3.3 rom (can be german, that doesnt matter). Once done that, flash wm6.
Success
Yeah! Thanks to vlodeck now everitging is all right! I flashed the original German AKU3.3 ROM by using this RUU:
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
(The original one gives "INVALID VENDER ID", of course, in German ) After that - successfully upgrade to WM6 TouchFLO.
Briefly:
1. First try to flashing WM6 - crash! The reason: old bootloader version (IPL/SPL = 1.12).
2. Flashing the Prophet ROM - success for FAT formatting. The Charmer turned back to life.
3. Flashing the German AKU3.3 ROM from T-Mobile, but through the No ID RUU.
4. Upgrade to WM6 TouchFLO by vlodeck. At the begining I reached the same problem, as described here:
http://forum.xda-developers.com/showthread.php?t=331717
but after istalling cert_spcs.cab and enablerapi.cab in my device I succeed to finish the process.
Thanks vlodeck, good job! This ROM is really amazing!
petrun said:
Yeah! Thanks to vlodeck now everitging is all right! I flashed the original German AKU3.3 ROM by using this RUU:
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
(The original one gives "INVALID VENDER ID", of course, in German ) After that - successfully upgrade to WM6 TouchFLO.
Briefly:
1. First try to flashing WM6 - crash! The reason: old bootloader version (IPL/SPL = 1.12).
2. Flashing the Prophet ROM - success for FAT formatting. The Charmer turned back to life.
3. Flashing the German AKU3.3 ROM from T-Mobile, but through the No ID RUU.
4. Upgrade to WM6 TouchFLO by vlodeck. At the begining I reached the same problem, as described here:
http://forum.xda-developers.com/showthread.php?t=331717
but after istalling cert_spcs.cab and enablerapi.cab in my device I succeed to finish the process.
Thanks vlodeck, good job! This ROM is really amazing!
Click to expand...
Click to collapse
WHERE I CAN GET BOUTH FILES cert_spcs.cab and enablerapi.cab
AND WHAT VIRSION OF PROPHET ROM SEND ME WORKING LINK THX DEAR
Charmer Stuck At Splash Screen
CHARMER STUCK AT SPLASH SCREEN
--------------------------------------------------------------------------------
I HAVE A MDA COMPACTII ''MADE IN TIWAN'' I WITCH WM5 I WANT TO UPGRADE IN TO WM6 SO I UPGRADE THIS WM6 TouchFLO Charmer WM6 ver. 2.1 FINAL by vlodeck AT THIS HOME PAGE http://forum.xda-developers.com/show...harmer+cert_sp... AFTER THIS I HARD RESET MY MDA C2 ITA ON BUT THE LANGUAGE IS NOT ENGLISH I CANNOT UNDERSTAND ....
SO I CAN REFLASH IT WITH THIS ROM Charmer_Touch_GER_Beta_2.7 .. AFTER FLASHING COMPLETE I SOFT RESET MY MOBILE.
SO MY MOBILE STUCK ON SPLASH SCREEEN ONLY T-MOBILE IS SHOW
MY MOBILE DETAIL IS AS UNDER
IPL 2.06 .0001
SPL 2.06 .0001
GSM 02.19.21
OS 4.0.0.0
PLZ DEAR SIR WHAT IS SOLUTION OF MY MDA C2
MDA2 CANNOT CONNECT WITH ACTIVE SYNC
Of course it cannot connect with ActiveSync, the device doesn't boot. One certain solution for bricked Charmer is Prophet ROM:
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
Use this link:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
In order to flash this, you should enter the bootloader, without using the ActiveSync. After that try to perform a hard reset, you probably will succeed to format the FAT partition.
if you cannot connect the pda to pc HOW CAN U PUT THE ABOVE PROPHET RUU ON CUREENT?
I have a charmer and I was trying to update to wm6. I can´t because the ipl is 1.12. I updated rom to german aku 3.3. But I can´t hard reset. format error. I´m trying to put prophet rom to format it, but when I send the prophet rom, it always give me an error at 95%. error 326 - this nbf file cannot be used fo your pda phone. please check your nbf file. the aku3.3 rom flashes ok. any idea?? I try tu send a radio rom. after that is the same. 95%error. please help. I can´t bring my charmerback to life.
Hello together,
I have the same problem like _mestre_.
I updated from T-Mobile AKU 3.3 GER to WM6 and flashed back to WM5 without problems, but when flashing again to WM6 from vlodeck my charmer didn't boot anymore and had that "Format is failed"-problem when making a hard reset. I could not recover my device until now with the method explained in this thread cause of the problems "error 326 - This nbf file cannot be used for your pda phone". So the Prophet Rom does not seem to work with boot loader 3.x. Has anyone any idea? Please help! Thank you very much in advance!
Yallah said:
Hello together,
I have the same problem like _mestre_.
I updated from T-Mobile AKU 3.3 GER to WM6 and flashed back to WM5 without problems, but when flashing again to WM6 from vlodeck my charmer didn't boot anymore and had that "Format is failed"-problem when making a hard reset. I could not recover my device until now with the method explained in this thread cause of the problems "error 326 - This nbf file cannot be used for your pda phone". So the Prophet Rom does not seem to work with boot loader 3.x. Has anyone any idea? Please help! Thank you very much in advance!
Click to expand...
Click to collapse
same problem here... any suggestions or is my charmer bricked?
Hi @ all,
**** happens, yesterday i tried to upgrade my rom on charmer (mda compact 2).
During installation system hangs on and didn´t finish.
So now i have only the startscreen and can reach the bootloader.
Tried now to flash an original rom, the ruu says error 294 invalid vendor id.
Otherwise the ruu (for no id) ended with error 238 file read.
My bootloder shows IPL 1.12, SPL 1.12 and USB connected.
I have read a lot of threads but cant find a answer for that.
Has anyone a good idea?
Thanks a lot for helping.
I wish all users in that great forum a happy new year
ronni
Hi Ronni,
same problem here. Do you found any solution?
Is it right, that your Device not charging and USB is not recognizing too?
Bg
Joy
Are you trying to flash WM6 ROM to your charmer? Because WM6 required IPL and SPL level at least 2.xx.
Did you tried this method to bring charmer back to life?
wow, thank you for your quick response. Hmm, I´m not shure, it´s a PDA from a Collegue, I don´t know, what he do with it. (I know only he try to flash something) Next week he take it to our office, then I try your solution
Thank you again
Joy
Bootloaderhang
Today i tried to update my rom... while the update i had an error.
i had updated the http://forum.xda-developers.com/showthread.php?t=363882
after the hardreset the phone hang by the first screen. I can press everething but nothing happens.
now I tried to flash a nother rom but it is unpossible because it can´t connect with windows mobile center on the pc.
Has anyone a good idea?
Thanks a lot for helping.
I wish all users in that great forum a happy new year
didi500
Hi!
this is my first post here, so sorry for my bad english or mistakes
i bought a qtek 9100 on ebay, and i'm wondering if it's a brick or not. i received the device 3 days ago. during this time i read through a LOT of threads here, tried a few things and nothing works.
here is some info:
- the phone is a qtek 9100 without branding
- the IPL is now 1.01 (i flashed "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE" successfully)
- the SPL is 2.18 (because of the missing suffix ".0001" i guess it's a G3)
- GSM is 01.12.10
- OS is 1.5.4.2
- when i start the device (without any button pressed) it stops at the splash screen (which was a qtek logo before flashing, and is now this picture with a beer, that says "some things last forever" )
- i can get into bootloader screen (color screen) by holding camera button while starting
- in bootloader screen a small "USB" appears when i connect cable to usb on pc
- when i press communicate and voice buttons (on the sides) while starting, the "Press send to restore factory default" screen appears, but pressing send prints out "Format FAT Partition Format is Failed"
- the device gets recognized by windows ("Mobile Device" appears on my computer)
- ActiveSync 4.5 does not connect to device, not even as guest.
- when i hit "Connect..." in ActiveSync's connection settings, nothing is found
("Allow USB Connections" is ON)
- the device is CID-locked ("FF" state in Mtty 1.42)
- i can't unlock CID, because i can't get "EnableRapi.cab" onto the device without ActiveSync connection
Ok, these are basically the things i know now. The problem is that i never saw any other screen then the "HTC" boot screen, the "Qtek" splash logo (the one with the clouds) before i flashed with custom ruu wwe, after that i see the new splash logo, and i can get into bootloader (color) screen. I never saw any windows mobile running on this device! I could never establish a connection with ActiveSync!
So i hope that someone here on this nice forum can help me get this device to work (WM5 would even be enough right now) or at least give me a hint!
Thanks in advance!
Put the phone in bootloader mode and flash back to the original ROM.
since i bought it in ebay i don't have the original rom of this device.
but i found "233309-qtek9100_2180707_21807109_20710_qtek_ger_ship.exe" through google, which seems to be an original qtek rom (version 2.18). shall i flash this one?
You can find in the Wiki the latest official roms of every brand for our Wizards .-
ok, thanks.
i found one (Qtek GER 2.18.7) and flashed it. the process was successfull, now the IPL/SPL is both 2.18 . But the device still doesn't start and stops at the splash screen (which is now the original qtek splash again). I can still get into bootloader mode and hard reset results in "Format is failed"! No ActiveSync connection either... how should i proceed now?
i basically narrowed it down to these two problems:
- the splash screen freezes
- hard reset error "Format is failed"
( IPL: 2.18, SPL: 2.18 )
can't anybody help please?
i'm freaking out about this
With everything i’ve read the only people who’ve had any success had CID unlocked devices.
ok, i think that too for what i've read so far...
is there any other way of CID unlocking except lokiwiz (can't copy enablerapi.cab without activesync!)?
would this imei-check service that i've read about work in this case?
meanwhile i've also tried something with mtty (r2sd all) but doesn't work -> "didn't get proper security level"
is this also because of the CID lock? i tried to find out the right password to enter in mtty, but found nothing that worked...
does anybody know the correct password?
I couldent CID unluck my 9100 with lokiwiz so i did it 5min ago with Wizard Service Tool (ha to reboot my computer).
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Look up the orignal rom on the wiki, get into bootloader. And flash it back.
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Like I sad before
Get into bootloader, flash back the original rom and try again.
mizobuchi said:
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Click to expand...
Click to collapse
I put the original rom.
But... the problem is the same.
when I started the device (without any button pressed) it stops at the splash screen (which has a qtek logo before flashing)
- i can get into bootloader screen (color screen) by holding camera button while starting, I installed the original and others rom who days before works perfectly... Now... this stopped at splash screen
- when I tryed to format.. = "Format FAT Partition Format is Failed"
Any idea?
I have tried this : http://forum.gsmhosting.com/vbb/showthread.php?t=332143
but... without success.
Could you help me, please?
Very Thanks
i'm still stuck with the same problem with hang up on qtek splash screen, too!
i have IPL 2.18 and SPL 2.18 and i can get in boot loader screen and connect with usb. (but no activesync connection!)
formatting doesn't work either.
does anybody have an idea how to solve this?? it's frustrating... i've tried almost every guide here on the forums.
same proplem here with
ipl 2.16
and spl 2.16
I used this to fix this problem
Hi i had the same problem the other week, installed a dodgy app, went to do a hard reset and wouldn't do a hard reset format failed. Tried updating rom everything worked ok until you booted it up. Wouldn't go past second splash sreen. After a few hours of trawling round i found this thread.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=format+is+failed
worked for me. Hope this helps you out.
Problem in connecting to my PC
Hey ,
I just bought a qtek 9100 a day before ... I tried to connect it with my computer.. instead of connecting my battery gets charging well can u plz help me out !
is there any software that i should install in my pc in order to get it connected to my PC...... please help me fast ! Lot of work is pending !
Thanks
Salman
Ok guys, I finally have this SOLVED.
My QTEK 9100 is working fine now!!!
I'm so happy with it right now
Since nothing I tried worked, I went to imei-check.co.uk and got my phone completly unlocked! It only cost me about 11€ and since it works now I have to admit that it was worth it (no advertising). After the unlocking was done I could do the "r2sd all"-method (Tool: MTTY 1.42) using a miniSD card. You can find a good tutorial on this board somewhere. After that everything was just fine...
-> I never saw it working and Hell Yeah: This baby just kicks a$$ !!! (although it's kinda 'oldschool' these days )