Database Develop

Maybe CID Lock problem ? NEED HELP !!!!

Hi, After the soft reset comand, I removed the battery from my Wizard. After that the followin problem was appear: the phone is bringing up to the splash screen and STOP on this position.I have tried to download another Rom but the problem still is the same. My Phone is not CID unlock and before this, I cooked own rom like is writen here http://forum.xda-developers.com/showthread.php?t=271043 . So any idea how to wake-up my phone MDA Vario.

Ok forgive me if I'm wrong here, I don't really want to judge before I know the full story, but seems to me your brain went on strike momentarily. First rule of flashing any unofficial rom CID UNLOCK YOUR DEVICE. Anyways sorry, I just wanted to say something so it doesn't happen to you again, that said, what rom did you try to upgrade to? what rom did you try to downgrade to after that? is your device a G3 or G4?
If your device is a G3 I would recommend downgrading to this rom by xelecin
ftp://xda:[email protected]_RUU_Wizard_1081002_108_10910_ENG_US.exe
it will ask you if you want to CID unlock your device at the start so you shouldn't need to worry about forgetting this time , if you can't connect your device to activesync just go into the bootloader (hold the camera, voice dial buttons while pressing the reset button) and once it connects run the set-up.
Oh another thing before I forget..... do some searching and read up a bit, because this is a pretty common topic on this forum, best of luck and hope everything works out ok. If not, report back.
*edit* I just noticed the thread that you linked to, I actually wasn't aware that this was possible, but anyways I think it's still much safer to CID unlock your device if possible, and another thing you might try replying in that thread if it doesn't work out since they should be more knowledgeable in the matter..... and that would help keep the forums less cluttered *edit*

Thanks, for your help, Unfortunately you are totaly right for my stupid act (again). At first i tried to solve the problem alone , but whole day I roam through this forum to find solution but I can't find the same problem like my. Maybe because of my ..... brain .Anyway I am with G3. NOW I have
IPL 1.0
SPL 2.26
GSM 01.09.11
OS 1.5.4.2
This is after this procedure http://forum.xda-developers.com/showthread.php?t=263116
I tried also to download also and Molski's 2.26.10.2 AKU2.3 Rom a.k.a. 2.26.10.2 Final Edition Rom, but the problem is the same : The splash screen is running and STOP and.... nothing.
I can go to bootloader and can download new rom, but I can't start fhe phone.

Yeah I know these forums aren't the easiest in which to look for info. So you can go into the bootloader, that's good. Don't try to go to a AKU2.x rom or later, keep it under that, so no 2.26 roms at all. 105, or 108 roms should be good.
Did you try the rom from the link I provided or the one on the thread? and afterwards did it go into the phone at all? My friends MDA had a similar problem last week, caused by the same thing, though in your case I see the SPL isn't updating when you install new roms on his it was the os that wasn't updating, but as soon as I installed that rom I recommended it booted up fine, then I updated his device to molski's 2.3.
I'll check back in a few so let me know how's it going.

Here's what you need to know & if you follow these instructions your prob will be solved.
The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
http://forum.xda-developers.com/showthread.php?t=285435
Wish u best of luck.

DoCtOr_X said:
Here's what you need to know & if you follow these instructions your prob will be solved.
The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
http://forum.xda-developers.com/showthread.php?t=285435
Wish u best of luck.
Click to expand...
Click to collapse
Ok, but tell me how to solve this :
"qiote"
8. Open ActiveSync, Explore and copy enablerapi.cab from your PC's C:\ (remember that's where you extracted lokiwiz to...) to you device, I don't care where.
9. Pick up your PDA, File Explorer, find the enablerapi.cab and click it.
"quote"
I don't have access to the phone explorer and phone at all.
masr1979 I have tried the rom you give me, but it look like there is some things I don't understand: When I start the exe file i have choice <continue> .Whet I type <c> 2(two) time the soft tell me <no device found> and order me to continue with copy ???. After few seconds tell me that Unlocker ..... Done!, and start HTC wizard Unlocker and NOTHING !!! Stop on this position more then 15 min. and only the led for charging on the phone is active.

Forget all about unlocking. Until you can boot the device completely it'll never work.
Try and install an official 2.x ROM on your device.
My suspicion is that you originally has a G4 device, which is bad because if you DID have a G4 you have a brick now...

Can you remember your phones old ipl/spl? for your sake I hope it wasn't something in this format 2.XX.000X.

masr1979 said:
Can you remember your phones old ipl/spl? for your sake I hope it wasn't something in this format 2.XX.000X.
Click to expand...
Click to collapse
Of course I'm not sure, but I thing it was 2.21. Anyway did you think that is posible to cook my own rom in G4? I'm totally confused.
Every time when I upload new rom I have this:
http://forum.xda-developers.com/attachment.php?attachmentid=32884&stc=1&d=1168184491
IMG_2976.jpg
...and also this is my bootloader screen
http://forum.xda-developers.com/attachment.php?attachmentid=32885&stc=1&d=1168184491
IMG_2977.jpg

Dr Puttingham said:
Forget all about unlocking. Until you can boot the device completely it'll never work.
Try and install an official 2.x ROM on your device.
My suspicion is that you originally has a G4 device, which is bad because if you DID have a G4 you have a brick now...
Click to expand...
Click to collapse
Thanks, but I try to find oficial rom but without success. And very interesting thing I found.. when I start to upload new rom the soft start to check my old rom and after that tell me that i have GE (german) language, but my old was WWE ?
Is it posible some one to give me some link to official 2.x ROM but for T-mobile german language.

Well the other day I tried finding that german rom for a while.... that search was going nowhere, I saw this thread, I don't know if you might want to check into it and maybe try it out. There's mixed results apparently but who knows
http://forum.xda-developers.com/showthread.php?t=276963

spv m3000 stuck at 98% with rom

Great my wizzard is stuck
its on 98% then de blue/green bar on my phone turned red en stays that way it doesnt do anything anymore, after a while my computer says the installation is finished, (SOMETIMES i get an error that has something to do with memory on my computer. or it says usb connection got lost or something)
i can reboot my phone but its going straight in the boot menu with those collors, i can try the downgrade rom again but it keeps getting stuck at 98%
anywone some suggestions?
I tried to install the folowing: CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
becose i wanted to unlock my phone (dont know if its locked or not)
I tried a few other roms but they wont install at all
I forgot some info:
ipl/spl 2.18 so i have/ (HAD) a G3
gsm 01.04.10
os 2.18.1.3
it is an orange m3000 (i have a t-mobile simcard)
im using my sim in another phone do i need the simcard in the m3000 ?
well a few minutes later:
i put my simcard in my phone, but it still hangs
i tried in now on 2 computers but both are stuck at 98%
on my second pc i get the message ERROR [302] : UPDATE ERROR
The ROM update Utility has encountered communication errors during the update process. The program will guide you stem-by-step to recover from te errors so you can continue with the update.
2 choices to click: View Document or Recovery
lol i did the Recovery it made me put out the battery and reboot the phone en replug the cables
well ill try again then... :|
did it about 8 times now, keep getting stuck at 98% notice that the bar becomes red at 98%
anywone please any suggestions? im afraid i bricked my phone

There are 24 people who look at this topic and nowone has a clue what i need to do???

kaasaanfiets said:
I tried to install the folowing: CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
becose i wanted to unlock my phone (dont know if its locked or not)
I tried a few other roms but they wont install at all
I forgot some info:
ipl/spl 2.18 so i have/ (HAD) a G3
gsm 01.04.10
os 2.18.1.3
it is an orange m3000 (i have a t-mobile simcard)
im using my sim in another phone do i need the simcard in the m3000 ?
Click to expand...
Click to collapse
is a 1.04.10 radio a valid radio for a 2.xx rom?
If you are stuck, the only/best way to recover is to flash an official rom from your carrier. You can get to the bootloader so you are NOT bricked. You are just flashing roms that have a CID that doesn't match your phones. Try the button rom or the wizard love rom that the unlocking stickies mention repeatedly.
Were your IPL/SPL 2.18 before you started?
Read the Wiki, Read the stickies. For every person that says the process doesn't work there are 100 that it works flawlessly for and 99% of the time those that can't get it to work don't follow all the steps in order or just outright skipped steps or substituted with what THEY thought was better. There is a reason for each and every step in the guides. IF you follow them properly you WILL NOT have any issues.
For the situation you are in now: STOP trying to flash custom roms, you MUST get your phone back to a usable state before you go down that path again. Use your carriers latest available rom to recover your device.
Also you are lucky to get an answer at all because your question is asked in almost every single new thread and every single ROM thread. The answers are already easily found if you take the time to look yourself.

thanks man, i tried the original orange rom and it worked.
RUU_Prodigy_2180103_21801103_OR_NL_DUT_Ship.exe
im so happy, thank you for all your helpful comments
2.18 before i flased is yes.
i wanted to copy a new rom to my device, but i thought it was cid locked.
so i followed step by step the guide from faria
http://forum.xda-developers.com/showthread.php?t=263116&highlight=stuck+at+98%
but i think the problem was that i did not have an aku2 or whatever that means.
Im sorry if im being rude, but you people do a wonderful job on those roms and step by step guide's but u forget that there are people that have no clue what aku2 means when i google is, it says a new rom from t-mobile with wm5 but it doenst say how somewone can check for themselfs if they have an aku2 rom...
Im verry sorry for those noob questions but it look like a heva the same rom that i had before i messed it all up.
so can i install a new rom from here? like one of these?
Pro Black 3[1].0.1.exe
CB-AIRAF.exe
?

kaasaanfiets said:
thanks man, i tried the original orange rom and it worked.
RUU_Prodigy_2180103_21801103_OR_NL_DUT_Ship.exe
im so happy, thank you for all your helpful comments
2.18 before i flased is yes.
i wanted to copy a new rom to my device, but i thought it was cid locked.
so i followed step by step the guide from faria
http://forum.xda-developers.com/showthread.php?t=263116&highlight=stuck+at+98%
but i think the problem was that i did not have an aku2 or whatever that means.
Im sorry if im being rude, but you people do a wonderful job on those roms and step by step guide's but u forget that there are people that have no clue what aku2 means when i google is, it says a new rom from t-mobile with wm5 but it doenst say how somewone can check for themselfs if they have an aku2 rom...
Im verry sorry for those noob questions but it look like a heva the same rom that i had before i messed it all up.
so can i install a new rom from here? like one of these?
Pro Black 3[1].0.1.exe
CB-AIRAF.exe
?
Click to expand...
Click to collapse
You will not be able to install a CUSTOM rom until you CID unlock. I don't believe the Black 3.0 rom is available for the Wizard. It is a Hermes rom. There are several WM 6 roms available for the wizard, you should probably look in the WM6 sub-thread once you get yourself completely CID unlocked.
The tutorial tells you everything you need to know, even if you don't know anything about anything. Just read the instructions follow the links to download the roms/tools that it is talking about. If you don't understand the instructions you can post in that thread and the authors or others will help you there. Though they most likely will not respond until you show that you have read and at least have an idea of what you are trying to do, where you started where you are and where you would like to end up. If you don't understand the instructions there is always the IMEI unlockers site that will give you a utility to do it if you want to pay them for it.
Why are you trying to upgrade? Do you need to upgrade? Are you willing to void your warranty on your phone? Can you live without it if something drastic happens and you truly do brick your device, in most cases you will not be able to exchange your phone under warranty? If you haven't defined the first question or answered no to any or all of the other questions you shouldn't be rom flashing, especially not with unapproved roms that aren't supported by your carrier. You need to measure the potential gains against the risk of doing these things to determine if it is right for you. Once you get unlocked and flash a couple of roms you will see that it is easy and relatively safe as long as you read and follow the instructions they are tried and true and do work if they are followed properly.
I would suggest using this thread to unlock your device: http://forum.xda-developers.com/showthread.php?t=285435

Zzan said:
You will not be able to install a CUSTOM rom until you CID unlock. I don't believe the Black 3.0 rom is available for the Wizard. It is a Hermes rom. There are several WM 6 roms available for the wizard, you should probably look in the WM6 sub-thread once you get yourself completely CID unlocked.
The tutorial tells you everything you need to know, even if you don't know anything about anything. Just read the instructions follow the links to download the roms/tools that it is talking about. If you don't understand the instructions you can post in that thread and the authors or others will help you there. Though they most likely will not respond until you show that you have read and at least have an idea of what you are trying to do, where you started where you are and where you would like to end up. If you don't understand the instructions there is always the IMEI unlockers site that will give you a utility to do it if you want to pay them for it.
Why are you trying to upgrade? Do you need to upgrade? Are you willing to void your warranty on your phone? Can you live without it if something drastic happens and you truly do brick your device, in most cases you will not be able to exchange your phone under warranty? If you haven't defined the first question or answered no to any or all of the other questions you shouldn't be rom flashing, especially not with unapproved roms that aren't supported by your carrier. You need to measure the potential gains against the risk of doing these things to determine if it is right for you. Once you get unlocked and flash a couple of roms you will see that it is easy and relatively safe as long as you read and follow the instructions they are tried and true and do work if they are followed properly.
I would suggest using this thread to unlock your device: http://forum.xda-developers.com/showthread.php?t=285435
Click to expand...
Click to collapse
I bought my phone second hand (i dont have a receet of something) so i dont have any warranty anymore
i like my phone but i have troubles with sms the recever keeps getting old of no messages so that why a want another rom
i would be a shame if i brick it, but im willing to try
im doing the steps from your link now, ik istalling te rom at the second point but it still is stuck on 98% :|
is there another 1.5 rom? that i can try? i read someting about the love rom

kaasaanfiets said:
I bought my phone second hand (i dont have a receet of something) so i dont have any warranty anymore
i like my phone but i have troubles with sms the recever keeps getting old of no messages so that why a want another rom
i would be a shame if i brick it, but im willing to try
im doing the steps from your link now, ik istalling te rom at the second point but it still is stuck on 98% :|
is there another 1.5 rom? that i can try? i read someting about the love rom
Click to expand...
Click to collapse
The Wizard Love rom is another that people use when the Button rom doesn't work for them. I don't have a link to it but I am sure it is linked in the Upgrading or G4 sub-forums. Maybe even in the Wiki. Sorry haven't been spending much time in the Wizard forums as I only flash my wizard when something breaks, or a new feature is added -- My wife uses that phone now .
There is always the pay to unlock website but you should be able to get it unlocked with either button or the wizard love rom.
Just out of curiosity how long do leave it sitting at 98% before you determine that it is stuck? All roms "stick" at a few points during the flashing process. If you didn't wait at least 5 minutes or get an error on your PC you probably didn't wait long enough. Best advice I have on this is disable all power management/screen savers on your PC set up the flash. Once it starts leave the room and close the door for no less than 30 minutes. This way you can be sure that you didn't interrupt it. For a Wizard the flash should complete in 10 minutes or less. For the Hermes it can take a full 30 minutes depending on your flashing method an which components you are flashing. It is normal to hang for a few minutes at different points during the flash process, just because there is no transfer doesn't mean something isn't being decompressed/written on the device from what has already been transferred over.

Zzan said:
The Wizard Love rom is another that people use when the Button rom doesn't work for them. I don't have a link to it but I am sure it is linked in the Upgrading or G4 sub-forums. Maybe even in the Wiki. Sorry haven't been spending much time in the Wizard forums as I only flash my wizard when something breaks, or a new feature is added -- My wife uses that phone now .
There is always the pay to unlock website but you should be able to get it unlocked with either button or the wizard love rom.
Just out of curiosity how long do leave it sitting at 98% before you determine that it is stuck? All roms "stick" at a few points during the flashing process. If you didn't wait at least 5 minutes or get an error on your PC you probably didn't wait long enough. Best advice I have on this is disable all power management/screen savers on your PC set up the flash. Once it starts leave the room and close the door for no less than 30 minutes. This way you can be sure that you didn't interrupt it. For a Wizard the flash should complete in 10 minutes or less. For the Hermes it can take a full 30 minutes depending on your flashing method an which components you are flashing. It is normal to hang for a few minutes at different points during the flash process, just because there is no transfer doesn't mean something isn't being decompressed/written on the device from what has already been transferred over.
Click to expand...
Click to collapse
Yes well i waited the first time for like 15 minutes then my computer shut down the update programm
today i waited like 30 minutes cos i even had dinner.
Well ill try the love rom some other time cos i need my phone to work sunday becose i need tomtom
thank you for your information i appreciate it verry much
i noticed that the original rom that does work: RUU_Prodigy_2180103_21801103_OR_NL_DUT_Ship.exe that one, also flashes red and green while installing so i guess thats normal...

Updating to WM6 ROMs on Vista

Hey All-
I'd appreciate any help anyone can offer. I am having problems updating to any of the WM6 ROMs out there (up here). One of a few things is happening:
1) Either RUU crashes just after it successfully sends my PDA in to bootloader mode, or
2) RUU is able to stay up, but for some reason, does not like the update file:
I either get an error: "This NBF file cannot be used for your PDA Phone. Please get a newer NBF file.", or
it suggests the nbf file is "corrupted", I think indicating the RUU util I am running is out of synch with what the PDA is expecting.
I'm using a T-Mobile MDA (Vario?) and Vista.
I've tried all of the solutions I have been able to find:
* changing the driver to HTC USB Sync so that it can "reconnect" once in bootloader
* various flavors of the update utility to get around the crash, which do not let me upgrade to the ROM of choice!
* hard reset of the device
* I even tried pulling down one of the ROM upgrades from the T-Mobile dowloads site and dropping that in with a WM6 ROM nbf file. That was a huge flop.
I know people have done this! I've seen it over and over again. So what in the world stupid thing am I doing to not make this work?
Thanks.
Joel Niemeyer
Seattle

RUU doesnt work on Vista. Use shelltool.

Thanks for the advice. I'm sure it was good advice, but I am three hours in to it running now, and I don't have a good feeling about it. I think it says it would take at least 15 minutes. Not 180! Ugh, now I wonder what I should do?
Joel

jniemeyer said:
Hey All-
* changing the driver to HTC USB Sync so that it can "reconnect" once in bootloader
Click to expand...
Click to collapse
How do you do that? Thank you because when i try to downgrade my ROM or w/e so that i can unlock it when i gots to bootloader the fred green blue thingy it doesnt reconnect to active sync and maybe thats my probelm...=[

chaos, just look around for the RUU with Vista instructions- they are everywhere!

hey mate,
just follow this instructions http://www.modaco.com/index.php?showtopic=252977 to falsh every official ROM under MS Vista. Surely, when it comes to WM6 you gotta use the Shelltool.
regards
irm

Answer for Vista
My question is why don't people just dual boot vista with xp or 2000/etc...that would solve a lot of issues about the problems with vista.. just boot to xp..
I figure if you have the $Funds$ to spend on a $250+ phone you could shell out $50 for a 150gb 16mb cache HDD for your pc and dual/tri/quad/etc... sheeet son i've been doing this for years with linux/m$/mac.
Gotta face it, some software just runs better on one OS over another. peace out.

can someone confirm shell tool work

ANTC said:
can someone confirm shell tool work
Click to expand...
Click to collapse
I tried it, took like 6 minutes then it was completed, knowingly it wasnt flashed right, but did the hard reset on the phone and was stuck at the SPL screen, so just loaded up VMWare to reflash.

It worked for me...
I flashed one of the WM6 ROMs using my Vista Ultimate computer. One of the main parts in making the thing work is remembering to put your computer in bootloader before doing it. On post #7 in the MoDaCo thread, it says this.
Once more, here is the link: http://www.modaco.com/RUU-on-Vista-It-can-be-done-the-ultimate-guide-t252977.html

so your saying witht hat tut you flash a custom rom??

Yes
Yes I was able to. I don't remember which, but I think i was Core 2.0

Yeah, I was able to use shelltool to make this happen. Thanks for the feedback, folks. Only hang up was that it had appeared to have seized up (was seemingly stuck before the "End" portion). I waited for like 3 hours before I finally threw up my hands and hard reset the unit. Low and behold my wizard booted up in to the new ROM and I have been good to do since!

Flashing to new rom

I'm sorry for this post, because the answer is probelly somewhere on this forum. But I can't find it.
I have my diamond for about a year now and I like to install a custom rom with windows mobile 6.5. But I can't seem to figure out what I need for this.
I already chosen a rom, but I have no idea if it is any good, because there are so many roms out.
http://forum.xda-developers.com/showthread.php?t=563245
So my first question, is this rom any good?
Second question, what type of hard SPL do I need, Do I need the normal one that requires roms to be signed or do I need the developers edition?
Third question. Do I need MTTY for this or can I first try it without MTTY?
And the last question, if I don´t like the rom is it easy to install the original rom again or do I need to do something special for that.
I hope you guys can answer my questions so I can start flashing my rom.
Grtz, Eric
EDIT: I tried installing hard-SPL unsigned, but get an error that it can't connected to my phone. But it is connected using windows mobile device center

why do you want to flash a new rom?

ive recenetly done the same, i wanted to flash my rom as the original was tied to vodafone and some of the features like youtube, facebook, and opera wouldnt work as they wanted vodafone connection ( im on virgin mobile).
anyway after much trial and error i in the end found it versy easy.
3 simple steps. first flash your bootloader
i found the best and easiest one was spl olinex version 4.0
u need to softboot to do this ( hold the down volume and switch on phone, have usb cable connected then use the flash util provided with the above.
once thats done you need to flash rom the radio
again the one out there that seems the best to use is version 1.00.25.05 diamondruu radio
again soft reset so you get the try colour screen and run the flash rom update ( takes about 2 mins at most)
finally choose your version of win mobile 6.5 ( i got windows revoluton 7.1 ultra clean edition)
do soft reset again, then run the flash update and again this takes about 5-10 mins for this)
all worked perfectly for me and it was my first try.
though i will be changing it as the revolution is missing some vital aspects i like.
i know its basic but hopeully you can see its not the daunting prospect some people make out though any rom upgrade carries a minot risk i found this to be as easy as 1,2,3
good luck

cloudedhopes said:
why do you want to flash a new rom?
Click to expand...
Click to collapse
Because I would like some new features on my phone. Like wm 6.5 or a new version of manilla. It's getting a little boring having the same phone for over a year.
@miramele, thanks for your response. I'll give it a try tomorrow and hope I won't brick my phone.

let us know how you get on, it took me several attempts as each time i was trying while within the phone itself, if you hold the down volume key and power on the phone you get the tri colour screen, in this mode i had 100% success each time.
doing it within the OS with phone on it just stuck at 0%.
And since then i have re flashed it with a diff version of wm 6.5 that i prefer and all is good.
the version i flashed to is the manila 2.1 with the latest touchFLO 3d so ive not even bothered with Spb mobile shell though may add this later.

miramele said:
let us know how you get on, it took me several attempts as each time i was trying while within the phone itself, if you hold the down volume key and power on the phone you get the tri colour screen, in this mode i had 100% success each time.
doing it within the OS with phone on it just stuck at 0%.
And since then i have re flashed it with a diff version of wm 6.5 that i prefer and all is good.
the version i flashed to is the manila 2.1 with the latest touchFLO 3d so ive not even bothered with Spb mobile shell though may add this later.
Click to expand...
Click to collapse
Thanks for the advice, if I understand correctly I have to get to the tri-color screen and then install hard-spl? But can I connect to my laptop while in this mode?
I'm gone try it tomorrow because I didn't have any time today.

Thanks for all the help, especially miramele.
I made the step and am now running a custom rom without any issues. Many thanks for the help and for pulling me over the line.

Restore device to OEM without touchscreen

Hello out there.....
First of all i have to say THX to all these people which are really willing to help every1 with their great tutorials. Ive used alot of them already. Thanks.
And i have to say sorry for my english language, due Im german and i left school behind long time ago. I'm really taken pains to write this comment.
Now, in my case ive tried to restore my device (Xperia X1i) to OEM status step by step as its shown in this thread.
My worst issue is that my touchscreen aint work anymore after i flashed a custom ROM and that i got stock at the point where the ROM wants to configure the OS like "Tap the screen to continue with configuration".
Ive tried to flash way too much ROMs using HardSPL but the touchscreen wont let me do anything - no reaction.
So how can I restore the bootloader (SPL) on my device, when my touchscreen aint work? How can I take the following step without any working ROM ?
sirsycho said:
12. Run SSPL.KAIS.exe from your phone (make sure you do this on your actual device and not your PC)
Click to expand...
Click to collapse
I do not know what I did wrong, that the screen wont react anymore, but im sure that the SPL is the cause for this disaster.
I'm really desperate couz i already have sent the device to the SE Support, where they told me that there is an "extraneous" on my device although ive flashed the Stock ROM firstly... there was still something that bothered them...
After i got the device back the touchscreen worked again as funny, allthough the support did nothing on the device as they said in the delivery.
A bit skeptical but with alot of happiness i kept on flashing some ROMs after that.
Now, after i found a good ROM and kept this one on my device for some days the screen doesnt work again.....
This is what my bootloader says right now
Code:
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
....seems like the HardSPL is still there......
Honistly i had to apollogize (maybe too late) that this part of using a cellphone (flashing a ROM using HardSPL etc.) is a big fish and that ive underrated it. Now i have a 400$-Device which aint work anymore
Ive read like all Tutorials here at xda-devs containing something about flashing a ROM or informations about SPLs; tried everything
I feel like im lost and fu**ed right now....
Is there any1 can help me with my problem?
Hopefully there is.....i pray for him

first flash a stock rom
then just run the hard-spl exe, and replace the ruu_signed.nbh file
why are you trying to use kaiser spl?
use the things found in the hardspl sticky in the xperia section

Wrong Tutorial
You're using tutorial for wrong device (HTC Kaiser)
The correct tutorial is in first post (extra how to: how to restore Stock SPL for warranty reasons.)
http://forum.xda-developers.com/showthread.php?t=431218
But before restoring original hardspl you should flash with original rom found in this thread http://forum.xda-developers.com/showthread.php?t=475482

wow thanks for your answers !!
i never thought ill get response.
Its really weird that i havnt found that tut before bcuz i was looking through whole board.
I will try do that tomorrow.
I hope that it will work then. Don't wanna pay 300$ for a new device

Else there is mtty to restore the bootloader

Aight i have done the steps showing in the tutorial.
1. I have flashed teh Stock ROM (R2A german - Vodafone)
2. I've used the RUU with the stockSPL given in that post.
Now my tricolour screen shows the following
Code:
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
This is what it shall looks like OliNex said.
I hope this is all i had to do, to make use of my device's guarantee, cuz the touchscreen still doesnt work
Seems like i really have to send my Xperia to the Support again (now hopefully with a ROM + SPL they wont reject)
But if i send my device with "extraneous" again i have to pay another 15€ just for let them do a costs estimate -.-
I would like to get a reply before i make use of the support again.
Thanks for all your help

Glad to hear recovering to stock rom + spl worked out.
Your touchscreen doesn't work when you have booted up windows?
If that's correct then I suggest to send in the device for service. Although
it might not help I suggest updating your device with SE updating service (SEUS) first.
After the flash remove the battery for 10 seconds, then turn it on.
Hope it helps and otherwise servicing the device is free of charges

Haha!
That's what im doing right now, using SEUS
Thanks for the tip with the battery but i already tried that way too often
Edit:
Ok, touchscreen still aint work....
Time to contact the support...at 11:45 PM **WOOT
nvm....Ill wait till tomorrow
gn8 and thanks for helping me with my issue ^^

a few days ago I returned my silver X1 for the same issue, my touch screen (digitizer) doesn't work. Then right in front of SE support person, he justed took out the battery and rebooted. Then it worked. The thing is, I did the same thing several times earlier that day and it did NOT worked. I am worrying of getting the same problem again and I only have until november 30th until my 1 year warranty expires. I haven't tried any cooked roms and it is because of warranty purpose. Altough I'm not new to custom roms since I own an Alpine and a Prophet. I've been here for some time now.
The thing that holds me back testing cooked roms on my Xperia is the aftermath if in case my device goes half-dead. I almost always read the restoring on to official roms everytime I get here, but still the thousand dollar spent on my phone's tag price comes with a fear of who's gonna rescue if my phone won't work. And to add that spare parts aren't available here as of the moment. And yes I'm eager and very curious about almost everyone saying cooked 6.5 is faster than stock roms but though I haven't tested it I have to disagree for now on my case basis.
First, my Xperia doesn't come with a carrier lock. It's locally called "open line" in my country I guess technically called debranding. Then my phone has the generic r3a rom via seus I think it's generic uk. Lastly, for some reasons, the touchflo 3d doesn't work with my device I've tried it since r1 firmware time. Some response told me to unlock-debrand my phone first but I dont have to since it isn't locked. Still installing tf3d makes my phone hang, doesn't uninstall, doesn't show in the themes list if installed as a theme, and doesn't let me have another panel since it always stay as tf3d whenever I choose another one. And it is very unstable in my device. These happened even if I install it as a panel.
I feel handsets here are faster than handsets that are locked by a carrier so I'm thinking again since for now, my Xperia works for me as stock as it is.