Bluetooth auto answer - Touch Pro, Fuze Themes and Apps

Hello all,
I have a raphael, I'm using Romeos 190.1 (waiting for 190.2) and i'm very happy with this phone...
However I'd like to know if a solution exists to make the phone auto answer when it's connected on Bluetooth (in the car).
I am using phone weaver and it's very nice to change profiles but still when I'm in the car or skiing with m BT helmet it would be VERY nice to move the phone setting to "auto answer" after 1 ring...
Thanks for the help

start, settings, phone (in personal tab), then in the more tab it gives you the option

Yes, but i don,'t want it to answer automatically ALL THE TIME, only in bluetooth mode (ideally only when Bt is active and connected...)
Thanks

Related

Diamond Bluetooth HeadSet Bug

Ok, not sure if anyone got the same problem as mine, but here is my problem:
I have a Diamond using AZTOR v7 Rom, radio vBS14 if that matters and Sony Ericsson DS205 as my headset. I start my bluetooth on my diamond and can pair up with the DS205 without any problem. I can also listen to music without lag and sound is also crystal and solid.
When there is a call kicks in, I can answer the call by pressing a button on my DS205..... However, the problem comes when I end my call, the headset will be disconnected afterward and I have to manually press a button on the DS205 to make it reconnect. Each time when I make a call or when I receive a call the headset will be disconnected.
Luckily (or not), I found a workaround: Whenever I pair up my headset, I need to go to Setting -> Bluetooth -> and "Refresh" the services that I want to enable on the DS205 headset. That involves un-checking the services enabled (including "Wireless Stereo" and "Hands Free") and re-checking the services again. After I have done this "resetting", the disconnection problem I described above will be gone.....
Each time I restart the phone or have the bluetooh disabled on the phone, I need to go through that manual procedure again to make my headset work perfectly.
As you can imagine, that is quite annoying.......does anyone have the same problem as me?
I don't have this problem, but i have another problem, when i use the orignal rom, i can use my headset(jabra bt3030) in my diamond and it will automatically connect to use hands free and wireless stereo mode when i turn on bluetooth, so when i change to use swift 7.5 full rom, i have to resetting the bluetooth in diamond everytime when i close bluetooth
I can only get wireless stereo for my Plantronics Bluetooth Stereo headset. Any ideas why I can't get hands-free. Radio issue?
It was possible with some earlier ROM, but I can't remember which... (yes, I'm a flashing addict).
I'm having the same exact problem & it's annoying as hell. At this point, I can't get the bluetooth function on the phone to activate at all. I use the same bluetooth on another phone with no problems whatsoever, so I know it's the phone. I'm running the original rom.....not a flasher.
Have you tried Jetware?
Sorry, just installing this doesn't change anything. Still no hands-free.
Is there a specific option you want us to set?
shinji_lee said:
Have you tried Jetware?
Click to expand...
Click to collapse
lit2fly said:
... Each time when I make a call or when I receive a call the headset will be disconnected.
Luckily (or not), I found a workaround: Whenever I pair up my headset, I need to go to Setting -> Bluetooth -> and "Refresh" the services that I want to enable on the DS205 headset. That involves un-checking the services enabled (including "Wireless Stereo" and "Hands Free") and re-checking the services again. After I have done this "resetting", the disconnection problem I described above will be gone.....
Each time I restart the phone or have the bluetooh disabled on the phone, I need to go through that manual procedure again to make my headset work perfectly.
As you can imagine, that is quite annoying.......does anyone have the same problem as me?
Click to expand...
Click to collapse
Yes - I have a very similar problem with my jabra SP700. The Diamond 'forgets' the wireless bluetooth mode every time I disconnect the two devices (although the Stereo Bluetooth icon is still showing in the status bar).
For a short while I was having to re-pair the devices every time I got in the car - until I found the same workaround as you.
There must be a proper solution???
Hello, I had that problem in my HTC Diamond with Pioneer DEH-700bt and my jabra 3030 and she solves when changing in the registry the key to it that identifies the device in pocketpc HKLM/Software/Microsoft/Bluetooth/Sys the key "COD" and I introduced the value decimal 5898764 that identifies the device in smartphone
luck
juanfervs said:
Hello, I had that problem in my HTC Diamond with Pioneer DEH-700bt and my jabra 3030 and she solves when changing in the registry the key to it that identifies the device in pocketpc HKLM/Software/Microsoft/Bluetooth/Sys the key "COD" and I introduced the value decimal 5898764 that identifies the device in smartphone
luck
Click to expand...
Click to collapse
I have this value in COD key but I have the problem anyway.
Any solution to this annoying problem?
i use my diamond with my bluetooth handsfree kit in the car, it is classed on the phone as a headset though. the sound is ok, a bit echoey but ok. but the microphone doesnt seem to pick up my voice, i have to really shout for people to hear me, on my old Xda Orbit it worked fine. any ideas?

Autoconnect A2DP when in range?

Hey Guys!
Is there a way to tell WM6 to automatically route Audio through A2DP as soon as a paired device supporting the profile is connected?
Clarification:
When using a Hands-Free-Headsetfor telephony you can pair it once, then turn it off, after that it is automatically connected to the phone as soon as you turn it on again.
In contrast to that a Bluetooth Stereo headset is not automatically connected, you have to manually activate it in Bluetooth Settings first before you can listen to music through it.
Especially with my car stereo used as "A2DP Headset" (which loses power every time the ignition is turned off) this can get highly annoying.
Is there a way to tell Windows to automatically "use" A2DP-Peripherals when available?
Try A2DP Toggle: http://www.teksoftco.com/index.php?section=freeware
The Today-plugin migt reconnect automatically, but it has a memory-leak...
To easily manually reconnect, you can create a shortcut to the exe:
\Program Files\Teksoft\A2DPToggle\A2DP.exe
Then you can put that program on your today screen easily.
And if you want a nice icon with that shortcut, you can change the shortcut file to:
53#"\Program Files\Teksoft\A2DPToggle\A2DP.exe" "-a2dp:1"?\Program Files\Teksoft\A2DPToggle\settings.exe,-0
downloadtest82 said:
Hey Guys!
Is there a way to tell WM6 to automatically route Audio through A2DP as soon as a paired device supporting the profile is connected?
Clarification:
When using a Hands-Free-Headsetfor telephony you can pair it once, then turn it off, after that it is automatically connected to the phone as soon as you turn it on again.
In contrast to that a Bluetooth Stereo headset is not automatically connected, you have to manually activate it in Bluetooth Settings first before you can listen to music through it.
Especially with my car stereo used as "A2DP Headset" (which loses power every time the ignition is turned off) this can get highly annoying.
Is there a way to tell Windows to automatically "use" A2DP-Peripherals when available?
Click to expand...
Click to collapse
Yep. The WM bluetooth stack sucks. It works better with some stereos though. I tried it out in the store with I believe a Pioneer (with bluetooth 2.0) and it was perfect. Turned it on and a2dp connects. Switch to another input and a2dp disconnects. Switch back to bluetooth audio and it connects. It was flawless. I ended up ordering the kenwood built in bluetooth unit (bluetooth v1.2) and it is terrible. I must manually toggle the bluetooth connection (I use a program that I wrote to do so, kinda similar to the above the above poster posted). Also, sometimes after a call comes in it wont reconnect. Sometimes i must power off then on the headunit a few times. Wasnt this thing supposed to make things easier?! A real shame because I love everyting else about the kenwood head unit. It works better with some ROMs on my phone (this is with a tilt; xperia on the way ).
Yeah, A2DP Toggle works for me as well, It's just dumb that this phone cant just do that itself. My old W880i could! I'm using a Sony DR-BT21G headset
JKingDev said:
A real shame because I love everyting else about the kenwood head unit. It works better with some ROMs on my phone (this is with a tilt; xperia on the way ).
Click to expand...
Click to collapse
A story to learn before you you buy the head-unit I spent almost an hour at Fry's to try many units w/ my Tilt as well (Sony, Pioneer, Kenwood, JVC ...etc) and ordered online w/ the JVC unit. Excellent sound (compare to other model) but disconnect after phone call issue exist. I believe it's HTC fault since my Eten M600 (MS BT stack) and Asus P525 (Widcomm) doesn't have this issue (but others....). But I got to admitted HTC one do have the best sound quality.
BTW, my JVC BT-1 will auto connect my X1/Tilt when I start my car and I think it serve my purpose.
Solution
wensing said:
Try A2DP Toggle: http://www.teksoftco.com/index.php?section=freeware
The Today-plugin migt reconnect automatically, but it has a memory-leak...
To easily manually reconnect, you can create a shortcut to the exe:
\Program Files\Teksoft\A2DPToggle\A2DP.exe
Then you can put that program on your today screen easily.
And if you want a nice icon with that shortcut, you can change the shortcut file to:
53#"\Program Files\Teksoft\A2DPToggle\A2DP.exe" "-a2dp:1"?\Program Files\Teksoft\A2DPToggle\settings.exe,-0
Click to expand...
Click to collapse
I have created an application wich runs the commandline setting automaticly, so you never have to do anything again it connects automaticly. You can find it here: http://forum.xda-developers.com/showthread.php?t=502549

Pairing the Bluetooth with Jabrasp700?

Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Edris said:
Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Click to expand...
Click to collapse
I have the same problem with my SP700 and my Tritton BT stereo headset.Phone calls work almost all the time through the SP700 speaker, but playing music or through the FM radio seems to be a problem. I can get them to pair up sometimes by only checking the Wireless Stereo box. It works for a few times, but then I have to delete and re-pair again.
I've searched for all over for answers, but nothing seems to be a permanent fix. It's very frustrating to use my devices for anything else but phone calls.
Just to add a bit of info, I do not have any problems with my old Motorola HS820. Of course, I'm not using SP700.
Hope that helps your troubleshooting.
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Possible solution
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Edris said:
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Click to expand...
Click to collapse
Thanks! Nice App! Tried it with my Tritton BT stereo headset and it works! Had to install to my device instead of Storage card, then had to delete and re-pair, but it so far I can toggle between on and off Stereo Headphones without any problem. Will try on my SP700 shortly.
I attached the Cab if anyone else wants it.
Thank you!
Works with SP 700!!!!!
Mal Bridgeman said:
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Click to expand...
Click to collapse
When the software loads, follow the instructions, do not install with any of the microsoft wizards that pop up, it will install itself. I couldn't find anything that lists what changes that were made.
SP700 Firmware
FYI,
I too had the same issues and downloaded the sp700 firmware update. I thought the same thing about the drivers, but called Jabra and they told me the firmware update has the drivers embedded in it. When you start the install you cannot plug it in till it tells you to. After you plug it in it installs the drivers. But BEWARE I have not been able to complete the upgrade, it stopped halfway and bricked. I called support and they said there is nothing to do, but luckily I bought it from Costco and they returned it. So being not so bright I tried it again but on a different computer (thinking that there might be a conflict) and it didn't even load and bricked it again. So I returned it yet again. So then I gave up on Jabra support and found A2DP toggle. It works good enough, so I am leaving it at that....
Take Care
David
Tilt WM6.1
andrew-in-woking said:
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Click to expand...
Click to collapse
I have the exact problem that you are having with the new, Hyperdragon IV, ROM.
Is this A2DP Toggle really the only way - I mean what's the difference between pressing a button on my Kaiser to reconnect and pressing the button on the SP700 ??
I have tried using Mortscript as shown http://forum.xda-developers.com/showthread.php?t=382172&highlight=a2dp&page=2 Although I edited the end out because it kills the player after ending a call. This hasn't helped either
I am off to see if the same problems occur with my lady's N96. If not and no good solution can be found for this I may have got her a new present.
Aren't I nice ?!
Found another possible solution, it,s called zoA2DP. So far it works flawlessly between my SP700 & stereo headset without having to toggle anything or change any settings. When you install it, delete your original pairings and add them again, make sure that hands free & wireless stereo are checked in advanced options on you BT settings. I believe this is a registry mod, there are no icons or any noticeable applications running in the backround.
The thread is here
http://forum.xda-developers.com/showthread.php?t=279127
Cab file attached

Bluetooth always discoverable app??

Are there any app's available which allows the Bluetooth on my Hero to be set as always discoverable. My handsfree car kit used to auto connect to my old Windows mobile device but now I have to make my Hero discoverable every time I enter my car and its very annoying.
DITTO
i would love this too, as it is a pain in the arse having to activate it all the time. Another stupid "improvement" from HTC.....what the hell were they thinking ???
You can add a Bluetooth On/Off Widget on one of the home screens.
Once the Hero is paired the devices should discover themselves with no issue. Set to discoverable or not.
My car kit very very rarely does not see and auto connect to the Hero. On the odd occasion that it doesn't connect, turning Bluetooth on and off via the HTC widget usually gets it hooked back up.
Its not perfect, but TBH no less perfect than other handsets I've owned.
Bluetooth file transfer is what we are really missing.
Having a nightmare with my car kit - PARROT CK3100 LCD and T-mobile G2
I have to turn on bluetooth make it discoverable the enter the pairing code ( everytime as it does not seem to keep the code) then the Parrot LCD flashes " MEM FULL " twic and then it connects but does not see the address book
Any suggestions much appreciated
Devchef1
Flash it
I was having very similar problems connecting my Hero to my car Bluetooth, it just would not pair, or work , i have flashed the official HTC update rom onto my Hero and now it connects everytime, no discover mode needed, and it works like a dream, you might want to give it a go, i fixed my issues .
Devchef1
I don't know why you have to keep pairing - mine auto detects no prob - both on stock G2 rom and Modaco 2.2e.
I can help you with the address book though - put a contact on your sim card. Anything will do, just make one up. Thereafter, I think you'll find your address book syncs.
Haven't seen the mem full thing, but I do recall you can only have five devices paired to the ck3100, so maybe you need to delete a pairing?
Cheers.
Rich
Android Bluetooth Discoverable Mode
Hi!
I'm having a similar problem with trying to keep the bluetooth on discoverable mode for some longer time as well. The phone I'm working with is the Nexus One and I was hoping anyone could help finding a way to get the app to turn on the discoverable mode automatically without having to request the user every 120 seconds or 300 seconds? The API for Bluetooth really limits me from making the duration of the discoverable mode longer and allowing me to change the bluetooth setting without user permission. Any help is appreciated.
Thank you!
AndroidTeam5
That is well and great that it reconnects for many people. But, for many people it does not! I have Myn's Donut running from my sd on my HTC Touch. It never auto-connects to my Pioneer Avic-f90bt. I have to make it discoverable or turn the bluetooth off/on every time I get in the truck. When I run the phone with WM6 it always, always auto connected...always. So if the easy fix is an app to leave bluetooth on, how hard can it be for a programmer to do this. Simply saying "oh, it works fine on my phone" doesn't help us!

Bluetooth and automatic discovery

Hi guys,
I have an X1 and a new Nokia6600 slide.
I have them both paired to my laptop and car (which have both bluetooth built-in) Both of the phones have bluetooth enabled and are always visible, all options to disable bluetooth or to stop being visible are disabled.
The biggest difference is this....
When I turn on my laptop or step into my car, my Nokia says, look I found your laptop/car, you're now connected! (without me doing a single thing)
My X1 is like ".........................." nothing... I have to manually enable the connection via for example ActiveSync, and chose to connect via bluetooth and then everything works fine.
I checked every setting concerning bluetooth or security and everything but I just can't find an option to make my X1 act the same as my 6600. It also doesn't matter if I just turn off the 6600 and have only the X1 turned on.
Maybe it is a setting, maybe it needs some tool or something.. I hope somebody here can help me or point me into the right direction.
Thanks!

Categories

Resources