Database Develop

Touch screen not responding after hard reset..hardware problem?

I have searched for solutions for the past 2 days but cant find one, if i missed it or this post is redundant , i apologize in advance.
Now my tilt is driving me crazy. It started last week when The touch screen wasnt working, but i fixed it by doing a couple of soft resets. then all the sudden, everytime i slide my keyboard out, the touch screen would stop responding. this went on for a day, then yesterday, when i tired to use the keyboard, the screen went blank, like the light died or something. but when i put it back on portrait, the screen would light up again.
A few moments later, the touch was responding, tried to use the keypad then the screen went blank..tried soft resets about 5 times and uninstalled all recent added programs (skyfire) ..finally the screen was working but the touch still wasnt working.
So this morning, i had the bright idea to do a hard reset....dumbest idea ever cos now its stuck at the screen where i have to "tap the screen to set up your wm device" and guess what..the touch screen isnt responding
plz i really need help with this. all so , i have a broken tilt.., well lcd screen is cracked...can i try to dismantle both tilts and replace the screens?

Ok, i used Code Factory's Remote screen alignment to bypass the alignment, but if i cant use the touch screen or the keyboard, the phone is pretty much useless for sending any information or making calls..is there a way to fix this?

I have had this same issue with my tilt. I could use the scroller on the left side of the unit to navigate but no touch screen. Both times that this has happened to me I removed the screen protector that I had on and restored a backup that I had on my storage card (I run a backup weekly). This has always fixed my issue. You could try another hard reset, not sure if that will help but do you get any lights on the keyboard when you slide it open? Is your tilt less than a year old because there is a manufacturer's warranty too.
Jim

when i slide the keyboard, i do get lights on the keyboard but not on the screen...it just goes dead..but when i slide it back in, the screen comes to life.
I cant do another hard reset cos i have to input the "1,2,3,4" code.
Also , the phone just got out of the 1yr warranty this month...awesome
I want to buy a replacement screen with a new digitizer but i need to be sure that is the problem.. ive searched for this keyboard problem but still have no answers

Now I'm having the same issue, touch not responding. I first noticed it about two days ago, when I slide the keyboard out, I could type just fine, but when I went to send the message the touch screen wouldnt work, so I'd close the keyboard and it would work. well yesterday it stopped working all together, so i used my d-pad and did a sprite restore and it started working again. But then On my way home i hit the lock button, and it stopped working after that, and I couldn't get it unlocked. I used the inner soft key to hit the first part of unlock, but then I couldnt ever figure which button to hit to get the on screen part of the unlock. So I had no choice but to do a hard reset, and just like highoct now I'm stuck on the stylus setup , and the touch still doesnt respond. does anybody esle have any suggestions ? Thanks in advance.

You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet

Oh yeah, I did manage to do a hard reset again, but now the screen is just white. I can hear the sound of it booting up but it still has a white screen. I tired going to the Bootloader screen ( Camera and power at the same time)...still have the white screen. I believe its a hardware problem but i don't know what it is...any ideas?

Ok now I've done a hard flash, using the same HTC kaiser rom 6.1 and it fixes the problem for a little bit, until the first time I slide out the keyboard , then the screen stops working again, any suggestions ?

iPhone 3G Screen Repair...finally an affordable answer
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!

Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.

Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Does this look like an apple website? did i say i had an iphone? GET OUT OF HERE!!!

Ninety Four said:
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Click to expand...
Click to collapse
And thats his only post, its spam. jerk him outta here

Tilt Touch Screen
highoct said:
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Click to expand...
Click to collapse
I know this thread is a bit old but was searching d forum for possible solutions cos yesterday i developed the same exact problem on my kaiser for no apparent reason!..flashing it hasnt helped and now im stuck on the wm setup screen..when u say u still have the same tilt with the original problem do you mean that the repair was unsuccessful? have you tried reparing it yourself? Thanks

I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.

grayfoxmg1 said:
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
Click to expand...
Click to collapse
same thing happened to me 3 days ago. touchscreen has just stopped responding.
it still worked when i slided my keyboard out, but only when it was out. then i realized it won't work at all (!) after soft reset. however, i could make it work again like that when i did the soft reset with the keyboard out. weird.
i tried searching, and decided to make a hard reset, flash a new rom, etc, etc., but no more touchscreen. at all. the device doesn't feel any touch in any case. nothing. i bypassed the beggining tap here with the storage card trick. (i've read it somewhere on the forum).
now i can only use my kaiser with the hw buttons, the keyboard, and that's it. no touch. really weird. please if anyone has any updates, solutions, anything, post. sniff sniff

mine doesn't have anything on the screen unless i slide it out, if i have it closed anymore, it just doesn't work at all.

try this:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!

se1988 said:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
Click to expand...
Click to collapse
well, i tried both tips, but they didn't work. i'd like to say a big thanks anyway!
then i grabbed the kaiser service manual and took my device apart into pieces. i reconnected pretty much all the cables and stuff, but still no touchy. any further ideas?

you should try replacing the screen. im happy to say that this screen from this seller on eBay worked for me: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250539984183
look here for dissasembly video: http://www.fonlogix.tv/tiltlow.wmv
(to save it to desktop right click link and "save target as")

thanks for your help, i've just ordered a new screen! phew, i hope it's gonna work

**~htc touch screen not working!!!!~**

hi,
my touch diamond 2's touch screen stop working randomly ( i think that i applied too much pressure on 1 spot for too long). I can see the touch screen dots on the area. I am just wondering if I were to repair this, would i be replacing the DIGITIZER or the TOUCH SCREEN.
Thank you soo much

warranty might cover that. It might not be your fault

I have decided to fix the part myself since I do not wish to ship the part to their location in the US. Any idea if its the digitizer or the LCD screen that i should be replacing?

jasonngu1991 said:
I have decided to fix the part myself since I do not wish to ship the part to their location in the US. Any idea if its the digitizer or the LCD screen that i should be replacing?
Click to expand...
Click to collapse
Search the Wiki, there are dismantle instructions.

I had the same on my display, and was able to move the dark spot to the edges where it disappeared.
I moved it with scratching it with my nail very gently applying some pressure.
In Europe HTC offers a pickup and return warranty, is that different in the US? If it is the same I would send it in to HTC for replacement, since it might happen again pretty soon....
I already have 3 screens replaced :-(

jason, did u manage to fix this? i have the exact same problem and pushing the "bubbles" towards the edge of the screen didn't help. my screen is still unresponsive..

mercurialcc said:
jason, did u manage to fix this? i have the exact same problem and pushing the "bubbles" towards the edge of the screen didn't help. my screen is still unresponsive..
Click to expand...
Click to collapse
Try applying duct tape to it repeatedly until you get it back.

Yes, both
I recently replaced the Touch Screen on my Diamond 2. Same problem; spots that "stick" in the middle. I used to solve this by running both my thumbs down the sides of the screen to "puff up" the low areas in the middle.
The part you want is actually called a "Digitizer Touch Screen" on eBay, cheap too. Prepare to spend about 2 hours fiddling with very tiny screws, connections and glue to tackle the job.
The hardest part for me was actually getting the Touch Screen to work; it seemed to be calibrated in mirror-image AND turned 90 degrees sideways, which made getting to the calibration functionality an extremely frustrating experience. I spend another 3 hours on that, but now I've got a perfect phone again, since I ordered a new case as well. No use taking the entire phone apart and then rebuilding with a molested outer shell...

maybe you should reset it

Working Solution Till Now
Hello Friends,
I have TD2 mobile and today I had same issue. I was thinking it was because of the weather or some.
I remember it did happend several time before, but when I restart the device several time it does work. So I was ignoring.... But today it did not work.. looks like going toward end... So I did soft and hard reset without and that did not helped me.
So I switched off the mobile, "heated" the touch screen gently with my hand for 1 min and started the mobile again and it worked for me .
Not sure if this is a solution, but will work.
May be I will contact Service Center here in Hyderbad and see what is wrong here?
Hope this will help you all...
Thanks.

Solution
Okay, I've just had this problem with an HTC Touch, and I think this works with any HTC that has a "digitizer" rather than an all-in-one touchscreen (I think newer phones have digitisers).
I'm not sure if this will always work, but I've just done it - sometimes the inactive touch screen is "broken" because the layers are stuck together (so the phone can't tell where the touch is, hence unresponsive). With mine, I looked at the screen side on and could see a kind of "oily" patch in the light.
The solution is to get masking/gaffa tape - the very sticky brown one. Stick it down on the screen/digitizer and then keep pulling it off - this pulls the layers from each other. I kept repeating this lots before it worked - and in the end I pulled the top layer completely off (I think you should pull from the top of the phone, as the layers need to be attached at the bottom of the screen/digitizer). Once it pulled away, I gently lay it back down (after panicking!!) and hey presto it started working again.
Good luck!

Digitizer replaced but still not working
The touch screen on my Touch Diamond2 stopped responding to my touch (or the stylus) and I tried everything including removing and replacing the digitizer bus just in case the connection was the issue. But all to no avail. Finally I decided to replace the digitizer (touch screen)
The problem for me is that it made no difference. The new digitizer doesn't respond to my touch either. The problem is apparently somewhere else.
If anyone has encountered this problem and has a solution I would be grateful to know what it is.
Thanks in advance

Replace the Touch Diamond2 Digitizer touch screen.
I recently replaced the digitizer (touch screen) on my HTC Touch Diamond2. Since I found on the net, no instructions for replacing the actual digitizer, I thought I might include some here.
It was relatively easy to fit. The only difficulty I encountered was a lack of information about how to actually remove the old one. The various instruction sets found on the web all stop once the screen is removed. But the digitizer is not covered by these instructions. The digitizer is bonded to a thin glass immediately under your screen protector (if you have one fitted) and after the screen is removed following instructions you will find on the net, the digitizer and the thin glass sheet that it is bonded to must be prized off from the front of the housing. The digitizer separates from the glass easily, but the glass is securely bonded to the housing with a silicon glue. It must be prized off by gently lifting a corner and applying a little upward pressure allowing the glue to slowly and gently let go. Don't be surprised if the glass breaks during the process. Once off it is a simple matter to press the new one in place. Just remember to start by slipping the connector bus (cable) through the narrow slot between the metal outer housing and the inner components. I used a set of tweezers to poke it through. DO IT FIRST before pressing the digitizer into place.
Okay, as I said the process was easy and took about 15 minutes all up.

prabhat said:
Hello Friends,
I have TD2 mobile and today I had same issue. I was thinking it was because of the weather or some.
I remember it did happend several time before, but when I restart the device several time it does work. So I was ignoring.... But today it did not work.. looks like going toward end... So I did soft and hard reset without and that did not helped me.
So I switched off the mobile, "heated" the touch screen gently with my hand for 1 min and started the mobile again and it worked for me .
Not sure if this is a solution, but will work.
May be I will contact Service Center here in Hyderbad and see what is wrong here?
Hope this will help you all...
Thanks.
Click to expand...
Click to collapse
i tried this and worked for me .
i removed the screen protector and switched off the mobile and heated the screen with my thumb and it worked again
thank you prabhat

and i'm using Topaz touch diamond 2
with photon ROM 1.6

Shoofty said:
I recently replaced the digitizer (touch screen) on my HTC Touch Diamond2. Since I found on the net, no instructions for replacing the actual digitizer, I thought I might include some here.
It was relatively easy to fit. The only difficulty I encountered was a lack of information about how to actually remove the old one. The various instruction sets found on the web all stop once the screen is removed. But the digitizer is not covered by these instructions. The digitizer is bonded to a thin glass immediately under your screen protector (if you have one fitted) and after the screen is removed following instructions you will find on the net, the digitizer and the thin glass sheet that it is bonded to must be prized off from the front of the housing. The digitizer separates from the glass easily, but the glass is securely bonded to the housing with a silicon glue. It must be prized off by gently lifting a corner and applying a little upward pressure allowing the glue to slowly and gently let go. Don't be surprised if the glass breaks during the process. Once off it is a simple matter to press the new one in place. Just remember to start by slipping the connector bus (cable) through the narrow slot between the metal outer housing and the inner components. I used a set of tweezers to poke it through. DO IT FIRST before pressing the digitizer into place.
Okay, as I said the process was easy and took about 15 minutes all up.
Click to expand...
Click to collapse
Thanks for the heads up on the glass part mate. Just replaced my TD2 digitizer too. Kinda freaked out at first when the glass split.. haha
Anyway, just wanna 1 more info. When removing the old digitizer, it'll be easier if the front housing was heated first (with a hairdryer on full or a heatgun) to soften the glue. It'll be easier to remove afterwards.
Word of warning though. Only head the housing when REMOVING the old digitizer, DO NOT use this method when applying the new one. The digitizer dies because of heat. Heat is what causes the newton rings issue.

Shoofty said:
The touch screen on my Touch Diamond2 stopped responding to my touch (or the stylus) and I tried everything including removing and replacing the digitizer bus just in case the connection was the issue. But all to no avail. Finally I decided to replace the digitizer (touch screen)
The problem for me is that it made no difference. The new digitizer doesn't respond to my touch either. The problem is apparently somewhere else.
If anyone has encountered this problem and has a solution I would be grateful to know what it is.
Thanks in advance
Click to expand...
Click to collapse
I have the same problema with my Diamond2. I have also changed the digitalizer with no success It is still not responding to any kind of touch.
Shoofty, did you manage to fix yours?
Thanks in advance,
Javier

Fixing TD2 touch screen
TD2 touch screen is a common problem I guess.
Symptoms are :
1- Touch screen does not respond sometimes
2- You can see a grease like layer under the touch screen
3- Sometimes if you look closer to the screen at some part you can see a a liquidized small area.
Solutions:
1- If you see the liquidized dot on the screen turn off the display and try to rub it with your finger until it disappears. turn it on again and try if it works. I guess heating with the finger as other peeople here suggest does the same thing. However this is a temporary solution. Your touchscreen will die at some date. I used my TD2 for 8-9 months using this method. But at the end touchscreen died.
2- Replace the digitzer or complete frontcover. Actually this might be easier than you think. I replaced mine in half an hour. I bought a front cover which includes the digitzer (http://www.ebay.de/itm/Original-HTC...zer_Ersatzteile_Werkzeuge&hash=item4cfe6f78dc) and openning tools from ebay. Dimanıond 2 disassemble and assemble videos on youtube were very helpful. I strongly suggest to buy the complete frontcover (inc digitzer). It makes replace process much easier and gives the device a brand new look. My old front cover was worn from the corners (which is also very commpn problem of TD2). Now it looks brand new. No strach on the display and body.

Thnks Ozkarah.
I happened to realize that, surprisingly, the touch screen of my HD2 started working if I heated it up with a hairdryer. So, I think something else is wrong beyond the touch screen, probably the connector to the main board of the mobile. It might expand once it is hot and that is why it starts working. In any case, I think that is beyond repair

HTC screen calibration
2Fresh said:
I recently replaced the Touch Screen on my Diamond 2. Same problem; spots that "stick" in the middle. I used to solve this by running both my thumbs down the sides of the screen to "puff up" the low areas in the middle.
The part you want is actually called a "Digitizer Touch Screen" on eBay, cheap too. Prepare to spend about 2 hours fiddling with very tiny screws, connections and glue to tackle the job.
The hardest part for me was actually getting the Touch Screen to work; it seemed to be calibrated in mirror-image AND turned 90 degrees sideways, which made getting to the calibration functionality an extremely frustrating experience. I spend another 3 hours on that, but now I've got a perfect phone again, since I ordered a new case as well. No use taking the entire phone apart and then rebuilding with a molested outer shell...
Click to expand...
Click to collapse
Hi,
I have same problem when I changed new screen (screen is calibrated in mirror-image AND turned 90 degrees sideways).
Could tell step by step how you get your screen calibrated?
Thanks

screen problem, most of the time do not work

Hi, i think i have problem with my screen, it's not work anymore, so I decided to reflash device with official Rom. But it didn't work.
Moreover before windows system start for the first time ir requires to tap on screen to boot. So now I cannot use my TytnII at all.
Is it any options to boot it without tapping on screen?
Or just to flash with other ROM, but HARdspl is not installed so a bit afraid to brick my phone. please help

hurdleman said:
Hi, i think i have problem with my screen, it's not work anymore, so I decided to reflash device with official Rom. But it didn't work.
Moreover before windows system start for the first time ir requires to tap on screen to boot. So now I cannot use my TytnII at all.
Is it any options to boot it without tapping on screen?
Or just to flash with other ROM, but HARdspl is not installed so a bit afraid to brick my phone. please help
Click to expand...
Click to collapse
install hardspl (same procedure as flashing) and then install rom of your choise if it dosn't work have you done any of the following
dropped it in water
gone in the washing machine
etc.... stuff like that

why don't you get a new digitizer??? it's $10 for kaiser?? i've been changing them like underwear...every half a year.
what is it, what's asking you to click on screen? if it's just a welcome screen, put welcome.not file in root.

papo said:
why don't you get a new digitizer??? it's $10 for kaiser?? i've been changing them like underwear...every half a year.
what is it, what's asking you to click on screen? if it's just a welcome screen, put welcome.not file in root.
Click to expand...
Click to collapse
hehehe funny expression 'changing them like [email protected]
what do you only change your underwear 2 a year

hehe, i live in Lithuania, so price with shipping will be around 25$. I think this isn't very cheap. Finally got screen working, but after 30min of using again no respond to tapping, then again working fine, and after that again no. it's annoying. I think it's problem with digitizer? I haven't it dropped to water, it almost brand new

hurdleman said:
hehe, i live in Lithuania, so price with shipping will be around 25$. I think this isn't very cheap. Finally got screen working, but after 30min of using again no respond to tapping, then again working fine, and after that again no. it's annoying. I think it's problem with digitizer? I haven't it dropped to water, it almost brand new
Click to expand...
Click to collapse
thats good you got it working
hope the problem doesn't happen again

if we assume the problem is harware, it would most likely by at one of two spots.
place, where the ribbon cable is soldered to lcd
or place where two piecies of digitiizer are connnected to each other.
might help if you check on the ribbon and glue a plastic tape all around the edge of digitizer, making it press little bit more on it
well, if that's hw probllem. but first you shoud try different rom. you can reflash without digitizer working. and check for pocket controller or similar if you want you can control pda from pc with it. there are two free and Pocket contr is trial.

if you just want to bypass the "tap here to use your device" message on the first boot up, search for "welcome.not".
create a blank file named "welcome.not" and place it in the root of your sd card and then power on the device for first boot up.
make sure it is a blank file. make sure it is named EXACTLY "welcome.not". if you are doing this with your windows pc, make sure you have turned off "hide file extensions of known file types". otherwise, the file might actually be named "welcome.not.txt" but might show as "welcome.not" on your pc.
search about it for more information.

hi, have tried differnt rom, but problem still persist. screen is not working, but sometimes it starts working very well. but most of the time it not respond. when backlight goes out and touch screen it starts to light but can't touch any options on. So what can be the problem, only digitezer or whole screen?

it was more probable it would be hw. but we need to eliminate all possibilities and reflash was easiest.
Still there is more things which could be the problem.
And there is no way to tell for sure what is it.
Did you say the pda is new? or digitizer?
And then you said when backlight goes off, digitizer will stop working, but still reacting on touch (to light the backlight) Is this right?
When will it stop / start working? Does it change if you press on body - case?
Does it change if you slide keyboard out or in?
There would be a short test each time pda/screen is powered, if digitizer fails in this test, it would be ignored till next test pass. Could this be your case?
digitizer could be broken on corner, or has bad contact inside
- You can test it, if you'll solder test wires on it and measure resistance, which should be around 500 ohms without touch and going down on each touch, can't go higher! test for both H & V
but the same reaction could be if ribbon cable connecting two parts of kaiser is broken (or connector on mobo side)
but if it's new it shouldn't.
and at last there could be problem on mobo. inside the controller chip or on it's connection, soldering. But not very probable.
It definitely looks like bad connection somewhere. You need to find out where, so you'll not buy digitizer if it's good or ribbon cable.
Put plastic tape around digitizer inside, as I wrote before, inspect ribbon cable and digitizer and it's connections. Try to locate event when it goes wrong.
If you'll not open it and check on these things, then maybe get a new part which will show bad, then I don't see how more we could help you.
You can use it without touch screen somehow or get a new phone.
Digitizer is US$8 with shipping to Lithuania. That's really cheap, even for us from central european countries.
http://cgi.ebay.com.au/HTC-P4450-Ka...m&pt=PDA_Accessories&hash=item5192adf317#shId
and ribbon cable have fair price too,
http://cgi.ebay.com.au/Flex-Cable-R...ewItem&pt=PDA_Accessories&hash=item3cadad06a3

papo very informative
All i want to add is that it's easier to replace the whole screen with a digitizer already on as the digitizer is very hard to remove since glued to the glass more than likely will get wrecked and not able to replace new, whereas full kit wont cost a lot more and will be less stress just 4 screws on the back plate of Tilt "where sim door is".

Well, it is not new, i've bought it from one girl, but it's like brand new, no scratching at all, very good condition.
also, yesterday i checked all the connection inside it, but the problem persisted.
I think I have understood what kind off problem it is...when remove sim card it stars to work perfectly. When insert sim, it work some time very well. Then again screen start not to respond, any ideas?

hurdleman said:
Well, it is not new, i've bought it from one girl, but it's like brand new, no scratching at all, very good condition.
also, yesterday i checked all the connection inside it, but the problem persisted.
I think I have understood what kind off problem it is...when remove sim card it stars to work perfectly. When insert sim, it work some time very well. Then again screen start not to respond, any ideas?
Click to expand...
Click to collapse
mm, I know some pretty good spells, but you need a magic wand to make them work. If you don't have any you need to:
tape the screen as I wrote before (half millimeter tape),
if no help, hardwire analog multimeter on digitizer and test it properly (while pda off and open) as I wrote before
tape bended paper across connector on mobo.
OR just get a new digitizer straight away. it's $8 and pretty good chance that it's the issue. it's maybe 50% chance but what I mean is:
You have $200 phone (now on market) let's assign it 200 points
It's working on 20% with digitizer broken, now you have 40 points
digitizer 8 points to add. With 50% chance to fix = 16 points to add
result: by adding 16 points you gain 160 (200 - 40) that's 10x gain = good risk

WTF with my screen? post photos. on the first my screen, on the second lcd screens which are beiing sold on ebay.
I decided to buy new digitizer, but when looked at my screen, it realized have completely different layout where digitizer is connecting to screen. Am i right? Is the digitizers which are sold on ebay will suit my screen?

that's fine. they all work. They are not oem but works well. Maybe not so scratch resistive.
You may get the digitizer solo, but they will not include a special double side tape which goes around and is holding it together. You can make that tape, but it's pain as stylez said. A lot of cleaning the used old one, then cutting small strips of ds-tape. and you need to put a paper or something in between two layers of tape as you need a little space in between. And then soldering that ribbon. Better just get whole assembly.
==
I see you tried that tape, before you buy it, try the last thing. The place where digitizer is soldered to lcd modul.
On that piece you sent photo of, you need to open back cover.
check the picture:
1. peel off antistatic tape from connector, from up -> down
2. take cover off
3. there will be attachment of digitizer behind the cover, like on your second picture.
Check for good connection
AND
check if soldered pins could not be touching the back cover you took off
( i had this problem once)
put electric tape accross it a give it a try - that will isolate it from back cover & make a little pressure if bad connection
=

[Q] Touch screen not working

My Droid's touch screen isn't working in the center vertically all the way down. I can still use the 'edges' of the screen. I need to use the middle of the screen for a few things (not transfering stuff over). Is there any way I can 'project' my Droids screen to my computer and click/touch in it to use it?
Thanks in advance for all help. It's appreciated
~mfungah
Edit: This is the original Motorola Droid.

I have the same problem on the right side of my milestone :S

I had the same problem, but from the back arrow upwards, specially when the phone got hot. As my phone was still on the warranty period, I flashed it back to stock and updated it to the official 2.2., took it to an Orange shop and got it back after almost a month: they basically changed the whole top part of the phone (I got a brand new screen )

Repair problem
I had a same failure. The touch panel was bad. I ordered one from eBay. It also came as well put it. It works well. Only so much wrong with me that for some reason the phone stacked in landscape mode, I can't change to portrait mode. What is wrong? I put together something wrong? I do not think so. Everything else goes. (or so it seems)

This has to do with the digitizer (the glass you touch over the top of the LCD you see) being defective or unsealed. This is due to environmental moisture finding its way into the phone and f**king with the electrictal signals sent by touching the screen. There is a 'phantom touch' issue that seems to happen before or during the vertical unresponsiveness, and that can usually be temporarily remedied by firmly pushing your screen downwards (your phone may restart) and taking a blowdryer to your phone until it's just hot enough to be uncomfortable to hold (and no longer take it into the bathroom while you shower). One way or another, you're going to have to replace your digitizer eventually.
Sent from my Droid using XDA App

I had the same problem months ago but it's now fixed.
STEPS:
1. Digitizer I bought from this guy:
http://cgi.ebay.ph/New-Touch-Screen-Digitizer-Motorola-Milestone-A853-/270780531 891?pt=UK_Replacement_Parts_Tools&hash=item3f0bc704b3#ht_2811wt_850
2. Dissasembly Videos (I advice you to watch them repeatedly before dissasembly):
http://www.youtube.com/watch?v=6d7ETMfgq2s
http://www.youtube.com/watch?v=dE81IaQHEHc
3. Phillips screw driver( for dealing with hard screws around the screen): Because I don't want you to use the low quality screw driver supplied with the digitizer.
4. Double sided tape: I got mine from a hardware shop for only P19. Buy a the more expensive tape(P100+) but look for a very thin one! You will use the cheap weak tape to stick some internal parts and use the Hard tape to stick the external casing. EDIT: I just used the cheap one for everything and it's strong enough.
5. PATIENCE: Don't be in a hurry. I even paused from time to time to get a better idea about what to do next. Get the feel of being a perfectionist (that same additude when I applied a screen protector )
That's the guide from me who haven't dissasembled a phone in my entire life but my milestone. So if something bad and technical that happens along the way then my knowledge can't help.. sorry.
Good luck bro!!

[Q] Repairing/assembling G1 -> broken volume rocker and touch panel

Well, I fixed my old broken G1 with new screen, touchscreen panel, case and keyboard.
Now I have 2 issue:
1) Sometimes my touchscreen goes grazy!! If I use the touch test application I see that sometimes when I touch the screen in an area there is another virtual touch in another zone of the screen. I read that it can depend from the current source when I charge the phone.. but I'm going crazy!! I opened my phone 10 times (I thought there was a problem in the cable that link TouchPanel to LCDPanel, because when I lock the cable with the clip it tends anyway to go out from the connector, now I put some scotch tape to fix but the problem is here.. so I think is another problem).
2) My volume rocker doesn't work!!
I bought 2 new keyboard to fix this problem, but no one of that fixed the problem. I thought the first new keyboard had volume keys broken, so I bought another one, but the problem persists!!
Now the Touch problem rarely happens, but the volume rocker is completely unusable..
Someone have experience about G1 assembling/repairing ?
Thanks and sorry for bad english

if you have put in multiple keypads have the same issue i would assume that it is the connection going to the motherboard. just a guess there but its either that or you have had a bunch of faulty keyboards.
only other thing would be a software problem
does the keypad work in recovery (let you go up down throughout the list) ?
as for the touch screen, probably need a new digitizer or flex cable, both are cheap and it sounds like you have the knowhow to replace them.

Ok, but digitizer is new!! screen also is new, and I have bought a total of 4 flex cable because I see that they are fragile (I broke the first I bought).
I tried to change flex cable but the problem remain the same.
The only thing that can be damaged is the LCD cable that links to the flex cable: it has a small cut where the cable have a curve, but the cut don't reaches the contacts (the cable is transparent). I also use some glue and scotch tape to mantein lock the cable.
The digitizer cable is connected to the LCD cable, and then they go to the flex cable that connect them to the motherboard.
The strange thing is that seems a software issue, because if I turn off and than turn on the screen, the problem is fixed for some seconds, minutes and sometimes hours...
Another strange thing is the possibility to control the screen with some metal objects from the moment that the virtual touch problem appear (I can control the screen also without touch it, with hand and piece of metal)
video:

have you tried a factory reset if you think it may be a software issue? if that dosent work you can try install a whole new rom.
really it sounds like it isnt the hardware since you appear to know what youre doing. i have a had a few phones that had screen (digitizer) issues and a new rom flashed cured it just fine
since you dont mind putting a few dollars into it, and your familiar with the inside, you can always try to pick up a cheap motherboard or spare phone from ebay or what have you, then swap the motherboard and you could then hopefully find out if it is the hardware or software

nagash91 said:
Another strange thing is the possibility to control the screen with some metal objects from the moment that the virtual touch problem appear (I can control the screen also without touch it, with hand and piece of metal)
Click to expand...
Click to collapse
Huh sounds like you got a cheap digitizer than. Most good digitizers use heat to touch. If it's literally touch, then sounds like its a fake/meh digitizer. i hate the digitizers that aren't heat, but press. I see them all the time in those first samsuck touchscreen phones. And they usually die in a bit. I had a Samsung behold with a screwed up digitizer

demkantor said:
have you tried a factory reset if you think it may be a software issue? if that dosent work you can try install a whole new rom.
Click to expand...
Click to collapse
Yes I flashed 3 or 4 roms after a wipe (I tried also super-wipe.zip), but the problem is here..
The digitizer works well some times, but sometimes get crazy (you can see in the video).
I don't that my new digitizer is fake, but I really don't know!
BTW I'm trying to repair my phone for fun (now I have desire z) and because I am fascinated by my old G1.
PS:
I see another strange issue--
If I touch the screen when the phone is on a table the screen digitizer is not very sensitive and can't take input from fingertips.
If I touch the screen when the phone is in my other hand, the screen digitizer is a lot more sensitive and it take input from fingertips.
My impression is that there is an electric field or something similar that disturbs the digitizer, and when I take the phone in my hand I discharge that field to ground. Also when I turn off the screen, seems that the electric field discharge so when I turn on the screen is ok, but after some seconds the field returns to disturbs the screen.
I really don't know, but is the impression that I have.. something that is not shielded.
Now I'll try to use my phone in airplain mode.
Thanks guys, I'm happy to see that this forum is still very active