[Reward] $125 Challenge to the community: Fix the infamous "audio lag" problem - Touch Diamond, MDA Compact IV General

[Reward] $125 Challenge to the community: Fix the infamous "audio lag" problem
Several HTC devices have a very annoying problem. When you playback audio, periodically (usually once every 5 minutes) you will hear a short "skip" in the audio. The sound has been described as a lag/skip/hiccup/tick/blip. It's all the same problem, though.
http://forum.xda-developers.com/showthread.php?t=412065
Whatever standard solution you can think of, it has been tried and failed (post to the above thread if you have a new novel suggestion). The problem appears to be deep in the wave device driver or possibly the hardware wave device itself. The problem does not seem to be present in A2DP. If you have skipping with bluetooth headphones, it's probably not related.
It seems to affect (at least), the Diamond, Touch Pro, HD, and XPeria. Possibly more.
There is a work-around (sort of), however. Some (newest?) versions of HTC's Audio Manager application (the TouchFlo player) ON SOME ROMS (not all) uses a non-standard method for playing back audio via DirectShow. These new versions do not skip, or at least do not skip on the regular five minute interval (it has been reported that some files don't play well through the Audio Manager for other unrelated reasons). However, this does not help the dozens of third party audio players.
I have asked HTC to provide documentation on how they did it. They refuse to respond, sending me a form email saying "we cannot support third party applications."
Conduits (makers of PocketPlayer) have told me they will implement the work around if somebody can figure out how to make it work. Their attempts to reverse engineer Audio Manager discovered this non-standard way, but when they wrote a test application, the skip problem was still present. So there is definitely more to the skip than simply sending audio via DirectShow. However, I think they are on the right track. It's just a matter of further reverse engineering Audio Manager until we get it right!
The Challenge!
The first community member to successfully create a very simple program to demonstrate lag-free audio playback (with full source code open sourced so that anybody else can use the method) will receive a pool of money from donators following this thread. I will personally chip in $15 US. I hope others will make commitments too (post below if you will)! When the solution is confirmed to work and can be replicated by third parties, I will send my donation via paypal and will post in this thread where everybody else should send their donation. If you make a commitment, you better donate!! lol. It likely won't be a whole lot of money, but I figure we have to reward the hard work at least a little!
To help you get started, here is the relevant information from the email conversation I had with Conduits where they explained to me what they found while reverse engineering Audio Manager.
We have done extensive tests regarding the HTC audio skipping issue, and have come to the conclusion that it is not something that Conduits can address. After analyzing the HTC Audio Manager program, and several other files (such as HTC’s DirectShow Audio Renderer HTCRenderFlt2.dll and HTCADXRenderer4.dll), we found that both are making some very special system calls into the WaveOut driver.
Here are some technical details for what we have found. First, we don’t think that thread or process priority have anything to do with the problem. Normal audio application use a cycle of ‘waveOut buffers’ that keep the audio output ‘full’ with audio data for the system to pull from and play. Applications use standard waveOutWrite functions to fill these buffers. From Pocket Player’s standpoint, these buffers are always full, and adjusting the priorities won’t affect this. One way to improve audio skips (that has affected the HTC TyTN) was to boost the thread priority of the WaveOut driver by editing a registry value under HKLM\Drivers\Builtin\WaveOut. This approach did not work here. Interestingly enough, these skipping problems occur on desktop PC’s. There, the problem is related to realtime drivers that take “too long” in their processing, which prevents the audio driver from processing the next batch of sound. This happens in Vista with some MacBook drivers.
The Audio Manager uses a different output mechanism from the standard waveOut calls – it uses the DirectShow audio renderer filter, which is another way to send audio. Looking in the internals of how it works, it is using a completely different mechanism. It is using a proprietary waveOutMessage call to open a new message queue, which audio is then “streamed” through.
Pocket Player (and other applications) could possibly resolve this issue by using the HTC Audio Renderer instead of their own waveOut routines, but then we would lose crossfading and other Pocket Player –specific features. We did some initial tests of creating a DirectShow filter graph (complete with their Audio Renderer) but still experienced the skipping, so there must be additional steps.
As a result, Conduits is now regarding this as a device-specific problem that the manufacturer is obligated to fix. Alternatively, if HTC wants to document their special “streaming mode” for their audio output driver, we could look into adapting to that model.
Click to expand...
Click to collapse
If you extract the Wavedev.dll from a ROM, you will see countless debugging messages regarding “MP3 Streams” and the like, indicating an entirely separate audio path for music coming from their software. If need be, we will rewrite our WaveOut output plugin (our output routines use a private plugin architecture just like our other plugin types) that uses the DirectShow output.
Click to expand...
Click to collapse
THE REWARD
US $15 - thx1200
Euro 8 (~US $10) - Prewien
US $15 - paulosgsf
US $20 - kennyb123
US $5 - john-vogel
US $15 - jay_zhead
US $10 - wired69
US $15 - Vince2301
US $20 - Liquid211
TOTAL: US $105

its a nice challenge for someone who's smart enough to really do this.. but it shouldnt be our problem in the first place
i'm stuck to this phone till nov. 2010.. so if htc doesnt fix this within a reasonble ammount of time and someone here on xda does, my 10 dollars (approx. 8 euros) is in too

I just bought my HTC and must stay with it till 2010 as well.. im on. $10.00

I really want my Fuze to be my primary music player.
I pledge twenty smackaroos...USD.
Let's get this fixed!
If HTC fixes it for 3rd party software, they don't get my cashola, just my appreciation for taking care of an issue that should have never existed in the first place.

5$ from me! (If it will work also with my HD)

The problem has supposedly been fixed in the latest HTC Diamond ROM revision (2.03.x.3).

AnnihilatorSC said:
The problem has supposedly been fixed in the latest HTC Diamond ROM revision (2.03.x.3).
Click to expand...
Click to collapse
Supposedly is the word... The issue is annoyingly present still.

Nothing has been fixed in the latest ROM. It's exactly the same as it was before.
I'd happily pay for a solution for this. Put me down for 15$.

I don't buy HTC touch hd till now cos of this problem, I don't understand why HTC still not fix it, or they can't cos it's hardware problem ?

Put me down for $10 (possibly more if I'm not too skint) but ONLY if the fix works with Pocket Player

Count me in for $15
Today the lag annoyed me more than earlier...

Almost to $100...
Thanks everybody! We're almost to $100.
How do we get mods to sticky this sucker? :-D

im gonna start bugging t mobile now for this... gonna head over to the shop

Updating my donation to $15 so we can have an even $100 reward!
Okay everybody, this is a good reward for a hobbiest! Evangelize this post around the WM community (but don't spam). Get the WM blogs to write about. Get exposure. Let's get some brains working on this problem and also keep increasing the pot.

So I do the same!
Updating my donation to $15!
so more than $100,00 for the one who fix the sound bug..

We were up to $125, but xda crashed and the restore from backup knocked off the last posts. :-( I hope people will repost those donations!
Thanks!

I see my donation of $20 is missing. I'm posting again...
Fix this annoying problem and you shall recieve $20 from me.

Liquid211 said:
I see my donation of $20 is missing. I'm posting again...
Fix this annoying problem and you shall recieve $20 from me.
Click to expand...
Click to collapse
Added back! Thanks!

Fixed:
http://forum.xda-developers.com/showthread.php?t=505928

flinx1 said:
Fixed:
http://forum.xda-developers.com/showthread.php?t=505928
Click to expand...
Click to collapse
I SAW! I just downloaded and will report back if it works with PocketPlayer. So far, people are saying it does. If it's true, I'm happy that HTC has finally acknowledged (let alone fixed) this issue!
EDIT: SCREWED THE OS ON MY SPRINT TOUCH PRO. Won't boot after installing. Please be sure to have a recent backup. Glad I did. I think it may not be CDMA compatible. :-( :-( But if somebody can somehow reverse engineer this sucker and make a CDMA version (or if HTC does), that would be awesome.

Related

Really annoyed:

I purchased the motorola HS850 a couple of days ago, seems pretty good paired up sraight away.
Problems are as follows.
The BT headset can't be used as a microphone for recording your voice, and/or giving commands to Voice Command software!!! Also i cant work out what pressing the button once quickly when not on the phone does. On normal mobiles you can announce a voice tag and it will dial the number. On the PPC (XDAIIs) it changes the icon of just headphones next to the start menu to headphones with audio coming out. Any ideas what this does? seems to create a connection to the decice, but still does not pick up audio from the BT mic!! One last thing is, on normal mobiles the HS picks up button presses etc, throught the BT speaker. No it doesn't even do that with PPC WM2003SE!!!
So in short the unit is pretty useless apart from answering calls by tapping the button on the headset. Kind of defeats the idea of a Btooth headset. Surely you would want to dial out using its built in mic? Am i just been stupid here, or should any of the above work?
Any workarounds or software that will work with BT Headsets? If not does anyone want to buy this from me for a fair price??? I mean what is the point? Can people tell me there postive uses please, or explain what im doing wrong!!! Surely if a crappy £50 mobile can utilize the features a £250 ppc should be able to, i mean come on!!
Anyone? I'm sure someone out there knows a little more about this than me? Im after some info!!!
I guess the answer is to buy the one designed for the device from O2?
As far as i know from the research i have done, it doesn't matter what h/set you have got!!
Matt
You are unfortunately right that ypu cannot control Microsoft Voice or therefore autodial with ANY headset at present. This is apparently due to the Widcomm Stack implementation (They haven't coded that part yet!).
Most users will also have difficulty with (System) sounds from the IIs presented on the headset. I believe that the new High Quality Stereo Stack has now been implemented but works with only a few headsets.
Where can the new stack be found from? or is it the 3900 stack?
I was led to believe it is in the 3900 stack but there was a CAB file floating around a while back for it (Never tried it myself so can't be of much more help I'm afraid!)
Thanks bebbo, anyone got further information on this problem at all?> I would like to get to the bottom of it, as their are hundreds of these kinda posts around all with no definative answer....Come on lets solve this and put an end to peoples suffering..... (MINE TOO!! )
Anyway, please post any information you know!!
At this time there are NO headsets that provide this function that I am aware of. If you highlight a contact,you can push and hold the headset button until it beeps and it will dial that contact.I was considering switching to the Nokia 9500, but it does not have that function either.
Maybe in the future,but not right now........Later
mattwaddy said:
Thanks bebbo, anyone got further information on this problem at all?> I would like to get to the bottom of it, as their are hundreds of these kinda posts around all with no definative answer....Come on lets solve this and put an end to peoples suffering..... (MINE TOO!! )
Anyway, please post any information you know!!
Click to expand...
Click to collapse

Phon call recording - no chance

This issues has been discussed several times but is there in the meantime a real solution to record also the voice of the caller without using the free speaker ?
Thanks for your help
myrin
peter7 said:
This issues has been discussed several times but is there in the meantime a real solution to record also the voice of the caller without using the free speaker ?
Thanks for your help
myrin
Click to expand...
Click to collapse
Nope, not any. Sorry, the Kaiser is crippled in this respect too (unlike, strangely, the Athena - the only current HTC PPC model to allow for call recording.)
peter7 said:
This issues has been discussed several times but is there in the meantime a real solution to record also the voice of the caller without using the free speaker ?
Thanks for your help
myrin
Click to expand...
Click to collapse
i use Vito Audio notes - works fine on my kaiser????
winwiz said:
i use Vito Audio notes - works fine on my kaiser????
Click to expand...
Click to collapse
It doesn't. Read my related articles - in there, I've explained it's not REAL recording you're hearing. For example, you won't hear the other party at all if you use any kind of a headset or use call recording in a noisy environment.
winwiz said:
i use Vito Audio notes - works fine on my kaiser????
Click to expand...
Click to collapse
Doesn't work on my Vario III, only when the speaker phone is on and then it causes a lag of a few seconds. Menneisyys is right, I tried in down the pub without the speaker phone on the other night and when I played back the conversation all I heard was me
Disappointing...
If call recording is a must then you have four options:
1. Use call recording software, always in speakerphone mode. Possible source of embarrassment when using in public areas.
2. HTC Advantage X7500 (Athena). Bulky, heavy and very expensive! Also possible source of embarrassment due to ugly device
3. Buy a Gigabyte WM phone. Most of these support proper call recording of both parties. (Also sold under other names. One example is I-Teq.)
4. Any Nokia Symbian S60 device. Wide selection of devices in a wide price range.
abubasim said:
If call recording is a must then you have four options:
1. Use call recording software, always in speakerphone mode. Possible source of embarrassment when using in public areas.
2. HTC Advantage X7500 (Athena). Bulky, heavy and very expensive! Also possible source of embarrassment due to ugly device
3. Buy a Gigabyte WM phone. Most of these support proper call recording of both parties. (Also sold under other names. One example is I-Teq.)
4. Any Nokia Symbian S60 device. Wide selection of devices in a wide price range.
Click to expand...
Click to collapse
5. Some (NOT all! See my articles for a complete list) ASUS and O2 XDA PPC models
6. HTC Oxygen (if you don't mind it being being a low-end Smartphone)
7. i-mate SP5 or Qtek 8310/8300 or SPV-C600
That's why i still use them next to my kaiser. I-mate for phone calls with pmrecorder and internet on my kaiser thru BT dun.
Only problem, no 3G and no BT Dun if you upgrade the smartphone to WM6.
A friend of mime is working on a reg tweak that will enable recording in-coming calls without having the speakers on. He claims that a two step procedure must take place; first is to funnel the call to the head set connection then carry it over to the recorder input. The caller will though hear a click, he said. but so far he was able to record only the caller and not the receiver of the call. Kind like the opposite of what happens now. He might come up with the cab file by next week.
The Universal does it too, on the very slight possibility that anyone cares!
Its this Damn modern stuff!! (BT)
I can remember when I were a lad and the stream only came on T' cable and we had a splitter that blead it to a pocket memo!
No, seriously, Menneisyys is correct. When you route call audio via BT then (at this time!) you can not intercept the incomimg audio for recording.
Please be patient, someone (on here or commercially) will do it.
Don't worry, in a couple of years when we have quad processors in our earbud connected sunglasses with integral viewscreen, we will be laughing at all our old worries. Just think, would you have thought ten tears ago you could have a unit the size of a cigarette packet that did all this? (HTC TyTynII and forget the US hybrids!)
Then you will only have to worry if the colour matches yours eyes!!
asfoor - is your friend ready with the application ?
thanks
myrin

Importing audio into the Kaiser

Hey all, I have been reading like crazy for months, have donated to the site and to some of the developers as well as pledging to the driver cause and doing my best to contact everyone from HTC to people in the press who have covered the issues as well as contacting people/organizations who haven't covered the issues yet.
I have searched and read everything I can about getting audio IN to the Kaiser and haven't seen much activity concerning the subject, so I thought it would be cool to create a thread that deals with this issue. I am going to use this thread to document my experiments. I believe this is the best way I can give back to the community aside from the financial support I show developers etc.
I am a pro musician & producer and want to use Meteor to record song ideas while I am traveling. I am looking to get line level signals into my HTC TYtN II and using the Meteor multi track recorder
http://www.4pockets.com/product_info.php?p=82
It would be very cool to use Meteor to write and record song ideas when I travel. It doesn't have to be super high quality audio, I just want to have a recording of my song ideas so I don't forget them. I have a little electronics device I plug my guitar in that makes it sound like a guitar amplifier. Think of it as a type of audio player for guitars that has an output like an ipod or whatever. I have a little drum machine and a synth keyboard and things like that (they all use line level signals). I do not want to use a microphone I want to use a line level signal from other devices.
Using this diagram
http://wiki.xda-developers.com/index.php?pagename=Trinity_EMUConnector
.... I am looking to get an electronics technician to make me a custom plug that will let me get audio into the TyTN II. I suspect that it will be a mic level signal as opposed to a line level signal but I am not sure about this. I have a great deal of experience with music gear, and very little experience with hand held devices in terms of understanding the hardware.
I suspect that whatever audio does get into the Kaiser will be treated as a mic signal, even if a direct signal is used (unless sendign data via USB is possible). I am going to try and get the tech to make a couple of custom cables using HTC's proprietary ExtUSB connector, but if I cant get one made for ExtUSB, I will get cables made that will work using one or more of the the inputs on a 3 in 1 adapter as seen here:
http://cgi.ebay.com/3-in-1-USB-3-5m...ryZ15040QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
I am assuming audio applications will be able to "see" the audio once it is sent via the connection.
Some things I am looking into:
1. What format the TyTN II will use for audio that is sent in to it through a custom cable?
2. What kind of quality will the audio will be? WHat kind of control will we have over that audio?
3. Will it be stereo capable or just mono? I am fairly certain that only mono audio is possible via the mic input part of the ExtUSB input.
4. I wonder if audio can be imported in real time via USB connection or if audio can only be imported via the pins that enable a mic for phone use?
Like I said, I will share what I find out and if anyone happens to have ideas or knowledge please reply in this thread.
There are other uses too, aside from using multi track audio applications. If I can get this to work (I am pretty sure I can) , how would you use it?If you have ideas, perhaps you can sHare ways we could take advantage of importing audio into the Kaiser.
Bump this, i have been thinking about this also, if it had 2 seperate headphone and mic plugs, the adaptors for say a guitar or bass would be basic, since the mic is mono and so are the insturments. If i had the tools for micro-miniature soldering, i'd be able to do it easily. but i dont, so if any1 wants to make a couple, i would purchase it in a heartbeat.
You can use meteor or any recorder on the handset, if you're in a quiet room the internal mic does record sound pretty good. if there was a way to do multi tracks at the same time(multiple leads) now that would be something.
Yep, big bump from me. MeTeor is fantastic, having a little recording studio anywhere is great. However, getting a line-in would just open up everything!
Caleb

Any better Bluetooth stacks out there

I use my Diamond as an MP3 player way more than a phone. I also use a Sony Ericsson Bluetooth Headset HBH-DS970 all the time. But very often I'll be listening when boom! The sound stops for some unknown reason. Many times it's a brief second or two and it starts again. Other times I reach into my pocket and hit the power button and poof, it starts again. Annoyed I put it back in my pocket.
Then sometimes it doesn't come back to life. Of course, I'm driving at the time and have to fiddle with the phone and drive, which is very dangerous.
Very often the bluetooth just drops. I have to go in, hit the power button, slide to unlock, Start: Settings: Connections: Bluetooth: Mode and I see the Turn on Bluetooth and Make this device visible to other devices toggled off even though I can see the little Bluetooth icon in the title bar is still on! I toggle on these and hit OK. Often I need to power off and back on my HBH-DS970 to re-establish the Bluetooth connection. Now the HTC Touch Diamond does not play a sound when the bluetooth establishes itself like my old PPC-6700 so I just guess and hit play on the HBH-DS970. Sometimes the I have the Wireless stereo portion working but the AVRCP is not working so play on the HBH-DS970 doesn't work and I have to hit play on the HTC Touch Diamond (Sprint Music). Later I'll find that Wireless stereo is working but Hands Free is disabled.
So why does this happen? Why does the Bluetooth drop at all? Is there any better Bluetooth stacks that have less bugs that I can install. I recall tell about something like a Widecom Bluetooth stack or whatever. Is that any better?
Recently I purchased a Motorola Rokr unit which is a unit for your car that receives a Bluetooth signal and rebroadcasts it to FM for your car stereo. It works great but the having to transfer Bluetooth pairing from my headset to the Rokr when I get in the car never goes smoothly. I have to remember to pause the program, stop the Bluetooth going to the headset, turn on the Rokr, it attempts to connect to the phone and it cannot if the phone is talking to the headset via Bluetooth. Why's that an issue? Why can't the Bluetooth talk to more than one device at the same time?!? I mean what if I want the Bluetooth music or program to go to two headsets simultaneously or to the headset and the Rokr? Shouldn't that be my choice.
Next I need to tell the Rokr to transmit on FM and establish that connection. Then I try to hit the pause/play button on the Rokr and often again, the Wireless is paired up to the Rokr but the Hands Free isn't. Get out the phone, power button, slide to unlock, Start: Settings: etc. etc. - what a pain.
Then I'll be driving and listening and life is good when suddenly again, the connection drops. The Rokr cutely has a female voice that comes on through the radio saying "Connection dropped". Yeah I know - and I'm not impressed!
Repeat procedure in reverse when leaving the car transferring the Bluetooth signal from the Rokr -> HBH-DS970.
LIFE SHOULD NOT BE THIS DIFFICULT!!!
So I ask:
. Is there a better, more reliable Bluetooth stack I can install?
. If not, are there some registry settings that I can tweak to make Bluetooth more reliable? I have used the Advanced Configuration tool and saw some settings about Bluetooth sound quality but I don't know if upping th quality had lessoned the reliability...
. What are some of the reasons that a Bluetooth connection will drop? I mean it's not like I've walked outside of its broadcast range - hell I'm still in the car!
. Finally, is there anything I can do to lesson the amount of short micro drops of 1/2 - 1 second? It's a little annoying when you're grooving to a tune and that happens.
Thanks.
Try this for some answers http://forum.xda-developers.com/showthread.php?t=432072
OT, can you record sound via BT headset's microphone? Not being able to do that annoys me much and still haven't got any answers from anybody.
I use the Bluetooth with phone calls. With Vito's Audio Notes I can record phone calls and hear both me and the caller in the recording - through the Bluetooth. I see Vito also has a "finger friendly" recorder but I'm not interested in that. However it seems clear the audio path from Bluetooth mic to recording can work.
Thanks for the pointer to that thread however the concern there is about Bluetooth quality not Bluetooth reliabiliy. Personally my Bluetooth quality is just fine - when the Bluetooth remains connected that is! I'm puzzled why you would have read my post and thought I wanted better Bluetooth quality?
I have been streaming audio since i got my HTC Wizard - 2 phones ago..
Back then, i was running WM5 and it had notoriously bad BT stack (really bad quality of A2DP audio). No tweak could eliminate the horrible high-pitched noise.
Fed up with the terrible sound, i tried the Widcomm stack.
This dramatically improved audio quality, but the Widcomm stack had other problems; i was not able to use any of my other BT devices. (back then i had a seperate GPS device and a Jabra wireless earpiece).
Eventually i managed to have both BT stacks installed, so i could choose which stack to start, depending on what i was going to use.
However, this was still far from perfect, because i wanted to be able to use my earpiece, use Tom Tom and listen to music at the same time (in my car).
The solution came (for me) with WM6, it had a really improved BT stack, the A2DP audio sounded much better.
For other applications the Microsoft stack worked well from the beginning.
When i just started using WM6 it did need some (registry) tweaking to overcome the problem of the "skipping" that sometimes occurred (those skips were not due to disconnection problems, it was just a matter of figuring out the highest bitrate the device could handle! (=>higher bitrate = better sound, more bandwidth, higher chance of music "skipping", =>lower bitrate = more stabile connection (less "skips", at the price of lowering the audio quality)).
Since my last phone (HTC touch) i did not even need to apply that tweak anymore, standard settings worked fine for me (acceptible audio quality, no 'skipping' problem).
Today i have a HTC Diamond, and i use a MBR-100 to stream audio to, i hook this device up to my car stereo (in fact, i have two, so i never run out of battery power).
I use my Jabra earpiece simultaneously.
I have no complaints whatsoever.
So to answer some of your questions, based on my own findings :
- The WM6 BT stack is capable of handling multiple connections at the same time (in my case, A2DP, remote GPS and Jabra earpiece)
- I never had a disconnect from my MBR-100 (which is also from sony Ericsson) without reason.
- I recently discovered,i can activate A2DP just by pressing the button on the MBR-100. Before, i always activated the connection by going to => settings=> Bluetooth etc. Maybe you have a button that does that on your headset? If so, it will at least save you the trouble setting up the connection again on your Diamond...
Finally, i don't know which ROM you are using, but the one i'm running now is the one from the official HTC website, "_HTC Touch Diamond_QMR_RUU_Diamond_HTC_NLD_1.93.404.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe".
One more thing :
- It is not possible to stream A2DP to more than one device at the time.
However, i found a nice little program to switch the A2DP stream between paired BT devices in reach.
It can also toggle the sound (and mic) from a phone call between my earpiece and the internal speaker.
Maybe it is useful for you as well : LINK
Copy .exe to the phone and execute there (when you have a A2DP connection running).
PaWs said:
OT, can you record sound via BT headset's microphone? Not being able to do that annoys me much and still haven't got any answers from anybody.
Click to expand...
Click to collapse
After toggling the sound by means of the program i mentioned in my previous post (This one) it definately records sound trough the earpiece (it's a Jabra BT350).
Thoroughly tested, 100% sure.
TheMusicMaster said:
I have been streaming audio since i got my HTC Wizard - 2 phones ago..
Back then, i was running WM5 and it had notoriously bad BT stack (really bad quality of A2DP audio). No tweak could eliminate the horrible high-pitched noise.
Fed up with the terrible sound, i tried the Widcomm stack.
This dramatically improved audio quality, but the Widcomm stack had other problems; i was not able to use any of my other BT devices. (back then i had a seperate GPS device and a Jabra wireless earpiece).
Eventually i managed to have both BT stacks installed, so i could choose which stack to start, depending on what i was going to use.
However, this was still far from perfect, because i wanted to be able to use my earpiece, use Tom Tom and listen to music at the same time (in my car).
The solution came (for me) with WM6, it had a really improved BT stack, the A2DP audio sounded much better.
For other applications the Microsoft stack worked well from the beginning.
When i just started using WM6 it did need some (registry) tweaking to overcome the problem of the "skipping" that sometimes occurred (those skips were not due to disconnection problems, it was just a matter of figuring out the highest bitrate the device could handle! (=>higher bitrate = better sound, more bandwidth, higher chance of music "skipping", =>lower bitrate = more stabile connection (less "skips", at the price of lowering the audio quality)).
Click to expand...
Click to collapse
Would you happen to recall what those registry tweaks were? Based on your above comments I think the best I can do is to lower the bit rates and bandwidth. Honestly most of my listening is talk radio and much less music. Even so, I'm older and I can't tell as much about the lose of highs, etc...
I have toned down things in Advanced Configuration Tools - Bluetooth section hoping that this increases reliability.
What I don't understand is why is this apparently so hard to get right? I mean this is not rocket science here! It's merely a connection that is radio based? Can't people code the software correctly! Geeze!
Since my last phone (HTC touch) i did not even need to apply that tweak anymore, standard settings worked fine for me (acceptible audio quality, no 'skipping' problem).
Today i have a HTC Diamond, and i use a MBR-100 to stream audio to, i hook this device up to my car stereo (in fact, i have two, so i never run out of battery power).
Click to expand...
Click to collapse
My car doesn't have an audio in, nor does it have Bluetooth (they're trying to sell you the OnStar crap).
I use my Jabra earpiece simultaneously.
I have no complaints whatsoever.
Click to expand...
Click to collapse
I don't have any earpieces. I don't know why I need an earpiece to stick in one year and hear things in mono with one ear when I already have a stereo head set that does this in both ears.
So to answer some of your questions, based on my own findings :
- The WM6 BT stack is capable of handling multiple connections at the same time (in my case, A2DP, remote GPS and Jabra earpiece)
Click to expand...
Click to collapse
Later on you correct yourself saying you can't do two A2DP's at the same time. That was specifically what I was asking about - a car A2DP and my headset A2DP (Or say two people with the same A2DP headsets, etc). I don't understand why this is limited. It seems artificial.
- I never had a disconnect from my MBR-100 (which is also from sony Ericsson) without reason.
Click to expand...
Click to collapse
What would be a valid reason for disconnection?
- I recently discovered,i can activate A2DP just by pressing the button on the MBR-100. Before, i always activated the connection by going to => settings=> Bluetooth etc. Maybe you have a button that does that on your headset? If so, it will at least save you the trouble setting up the connection again on your Diamond...
Click to expand...
Click to collapse
The Rokr has essentially 4 buttons. Power, FM selector, Call pickup and Pause/Play. There are also some combinations. The FM Selector is simply a button to push where the Rokr scans the stations and tells you which station to set your FM radio to. Power is for power, naturally. The Call pickup and Pause/Play are as their names suggest. Pause/Play pauses or plays the media player on the other end of the Bluetooth (through AVRCP) and Call pickup picks up an incoming call. Both of these buttons attempt to talk to the remote Bluetooth device if the connection is not currently established. However since most of the time the problem is that the Bluetooth dropped it's connection (necessitating having to go throught Start: Settings: Bluetooth: Mode: Turn Bluetooth on). Also, turning off the power and turning it back on causes it to try to pair up again, which sometimes work. However, if you currently have it broadcasting to your FM radio and your radio turned up, powering it off kills that connection causing loud static to come out of your radio until you power it back up and re-establish the FM broadcast portion.
I can see if I can screen capture my HTC Touch Diamond with the Bluetooth off in the Bluetooth settings but the Bluetooth indicator actually on in the title bar. Weird state! You should never be in that state with one part saying Bluetooth is on and the other saying Bluetooth is not on!
Finally, i don't know which ROM you are using, but the one i'm running now is the one from the official HTC website, "_HTC Touch Diamond_QMR_RUU_Diamond_HTC_NLD_1.93.404.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe".
Click to expand...
Click to collapse
I'm using whatever came on my Sprint version of the HTC Touch Diamond.
Do you know of a Widcomm stack for the HTC Touch Diamond? How about a copy of the MS Bluetooth stack? I did turn down the bandwidth/bitrates and hopefully that'll make it more reliable. However it would be nice to have those Bluetooth stacks available to install and play with.
TheMusicMaster said:
One more thing :
- It is not possible to stream A2DP to more than one device at the time.
However, i found a nice little program to switch the A2DP stream between paired BT devices in reach.
It can also toggle the sound (and mic) from a phone call between my earpiece and the internal speaker.
Maybe it is useful for you as well : LINK
Copy .exe to the phone and execute there (when you have a A2DP connection running).
Click to expand...
Click to collapse
I had seen this program before. Perhaps you can explain how it's supposed to work. Because whenever I run it it does nothing.
I have two HBH-DS970's. I pair them both up to the phone. I can play music but only through one of them. When I run the Bluetooth toggle thing it first plays in the current HBH-DS970 but pretty much out of phase (sounds tinny). If I run the BT Toggle again it briefly (for 1/2 a second) plays on the speaker phone then plays in the same HBH-DS970 but in phase (full bass). The toggle toggles between these two in phase/out of phase sounds with a brief blast on the speaker phone but only in one of the HBH-DS970.
If I power off the HBH-DS970 and establish Bluetooth connections with the other HBH-DS970 and I do the BT Toggle thing again the same thing happens with the second HBH-DS970. It does not transfer the BT from one HBH-DS970 to the other! I suspect it wouldn't transfer the BT from an HBH-DS970 to the Rokr either.
I don't get it! What's this BT Toggle for?
defaria said:
Would you happen to recall what those registry tweaks were? Based on your above comments I think the best I can do is to lower the bit rates and bandwidth.
Click to expand...
Click to collapse
You're correct. They are the same tweaks that are now provided in the advanced configuration tool. Back then, when i just had my Wizard i did not have this tool and i had to go into the registry to change the settings manually (they can be found under \HKLM\Software\Microsoft\Bluetooth\A2DP\Settings).
The most important one is BitPool, i use 58 for the quality of the audio, but since you mentioned you use it to talk radio and not so much listening to music you can set it to 30. You should not experience any buffering skips then.
Then you have MaxSupportedBitPool, which you can delete. I played with changing the settings here but no major effect.
Finally, there is UseJointStereo, to have stereo set it to 1. In the older WM6 BT stacks when set to 0, it would reduce the hissing noise but the audio would be mono.
defaria said:
I don't have any earpieces. I don't know why I need an earpiece to stick in one year and hear things in mono with one ear when I already have a stereo head set that does this in both ears.
Click to expand...
Click to collapse
I only use the earpiece to make calls while driving, not to listen to music..
defaria said:
Later on you correct yourself saying you can't do two A2DP's at the same time. That was specifically what I was asking about - a car A2DP and my headset A2DP (Or say two people with the same A2DP headsets, etc). I don't understand why this is limited. It seems artificial.
Click to expand...
Click to collapse
My MBR-100 uses A2DP, my earpiece HFP. That's why i'm able to use both at the same time. However, you can't use A2DP 2x simultaniously. I was just pointing out that the BT stack of WM6 is capable of using different profiles simultaniously. If your Rokr and your Sony headset use different profiles, you could have used the small BT toggle program to switch easily..
But even if they use different profiles, you can't use the audio output twice at the same time. You can only toggle to wich profile it redirects.
defaria said:
What would be a valid reason for disconnection?
Click to expand...
Click to collapse
The only thing i can think of, is when the two are too far apart from each other. I did not have any strange disconnects so i don't have the same experience.
You mentioned you are still running the original ROM, and if you have the time it is not a bad idea to upgrade it. I know that in the beginning of WM6 A2DP did not work as well as it does today (i had to tweak then, now it works well with default settings). Also because you mentioned your BT behaves irratically.
The process of upgrading is relatively easy and you will gain a performance boost as well.
defaria said:
Do you know of a Widcomm stack for the HTC Touch Diamond? How about a copy of the MS Bluetooth stack? I did turn down the bandwidth/bitrates and hopefully that'll make it more reliable. However it would be nice to have those Bluetooth stacks available to install and play with.
Click to expand...
Click to collapse
Since i had my Diamond i never had problems with BT so i didn't search for that. I did save some of the stacks i experimented with when i had my Wizard, but i dont know if they will work on te Diamond... If you can't find anything on this forum, let me know and i will post the cab's for you.
But again, i don't know if they will work on te Diamond!v
defaria said:
I had seen this program before. Perhaps you can explain how it's supposed to work.
....
I suspect it wouldn't transfer the BT from an HBH-DS970 to the Rokr either.
I don't get it! What's this BT Toggle for?
Click to expand...
Click to collapse
The BT toggle app does nothing more than redirect the audio to the next available (connected) device. I use it switch to earpiece, when i answered the phone with the buttons on the Diamond (when i answer calls with the button on the earpiece, it does that automatically).
When listening to music, i can switch the audio between the earpiece and the car stereo.
So i figured, maybe you could use it in the same way, when you walk to the car enjoy the music trough your headset, and when you are in your car, click whatever button it is on your Rokr that activates the connection and simply click the icon to change the audio from your headset to the Rokr.
edit :
After reading your story about your Rokr again, i begin to believe there is something wrong with the BT portion in your Diamond (connection dropping, having different icons say different things about BT state). Your Rokr wants to make the connection by pressing the button, and that is how easy it should be.
That's how it works for me. I would recommend upgrading to the latest ROM, i downloaded it from the official HTC website.
I mentioned the exact filename with version number a few posts ago.
That way, you will be sure that software (BT stack) is o.k., i can confirm that in my case it does what it is supposed to...
TheMusicMaster said:
I only use the earpiece to make calls while driving, not to listen to music..
Click to expand...
Click to collapse
But my point is that the HBH-DS970 can do both. IOW while listening to music (or talk radio), if a call comes in then you simply hit the little call switch on the mic and the music stops and you answer the phone. Talk on the call and listen in both ears then hit the little call switch on the mic and wham you're back to your music or program material. It's really quite cool! When it works that is! Or, if you weren't listening to music and a call comes in simply put the earbuds in (they conveniently fall along the necklace of the HBH-DS970) and talk. IOW, given this, what would I need or want a mono earpiece that just answers calls when this will do both?
My MBR-100 uses A2DP, my earpiece HFP. That's why i'm able to use both at the same time. However, you can't use A2DP 2x simultaniously. I was just pointing out that the BT stack of WM6 is capable of using different profiles simultaniously. If your Rokr and your Sony headset use different profiles, you could have used the small BT toggle program to switch easily..
Click to expand...
Click to collapse
Define "different profiles" in this context...
But even if they use different profiles, you can't use the audio output twice at the same time. You can only toggle to wich profile it redirects.
Click to expand...
Click to collapse
That may be what the BT Toggle does and it may be that you cannot use two A2DP stereo outputs at the same time. What I'm asking is "Why not? Why this seemingly artificial limitation? Is is security concern? Did nobody think anybody might want to do this? Is it a hardware limitation? Is it a Bluetooth 2.x limitation?". It just seems silly to me to put a limitation like this for seemingly no particular reason. Ya know some people might want to actually share their music in like real time!
You mentioned you are still running the original ROM, and if you have the time it is not a bad idea to upgrade it. I know that in the beginning of WM6 A2DP did not work as well as it does today (i had to tweak then, now it works well with default settings). Also because you mentioned your BT behaves irratically.
The process of upgrading is relatively easy and you will gain a performance boost as well.
Click to expand...
Click to collapse
I've done some ROM updates back with the old PPC-6700. Yes there were better but they also weren't supported. I'm with (crappy) Sprint but I think all carriers shy away from you burning in a new ROM on them. They only support you not touching anything like that. In fact, IIRC the original Sprint ROM for the PPC-6700 didn't even support stereo Bluetooth at all! It was only after installing the Widcomm stack that I was able to get stereo BT working!
And that's part of the scary part for me. Originally, the first BT stack I installed worked fairly well with MS Voice Command actually working and when a call came in while I was listening to music, it would properly pause the music, answer the phone then return to the music. But that lasted only a short time. For most of my 2 years with that phone the BT would not stop the music to answer the phone.
The current Sprint derived HTC Touch Diamond ROM works WRT the BT behaving properly for stuff like that. The only real problem I'm having is with the dropping of the connection. So if I go to a new ROM and that breaks... well I don't want that happening. Perhaps if you could point me to the original Sprint ROM so I can get back to where I'm currently at I would venture into newer ROMs.
But another thing that would make me go for the new ROMs is if I could get rid of the god awful Sprint Music Player (SMP or actually the HTC Audio Manager and its Today plugin)! This thing sucks! I usually use Pocket Player however the god damned SMP steals the AVRCP controls such that Pocket Player cannot get them. So I can't use Pocket Player and then have the Play/Pause button on my HBH-DS970 play or pause the SMP! You end up having two audio streams playing at the same time and the pause button does not pause Pocket Player! If there's a ROM out there that removes the silly SMP then I'm all ears!
Since i had my Diamond i never had problems with BT so i didn't search for that. I did save some of the stacks i experimented with when i had my Wizard, but i dont know if they will work on te Diamond... If you can't find anything on this forum, let me know and i will post the cab's for you.
But again, i don't know if they will work on te Diamond!v
Click to expand...
Click to collapse
I'm a little leary replacing the BT stack that's currently working pretty good (aside from the dropping problem) unless I can assure myself that I can re-install it if the new one doesn't work.
Oh and let me say MusicMaster, you've been very helpful so far. Thanks.
TheMusicMaster said:
The BT toggle app does nothing more than redirect the audio to the next available (connected) device. I use it switch to earpiece, when i answered the phone with the buttons on the Diamond (when i answer calls with the button on the earpiece, it does that automatically).
When listening to music, i can switch the audio between the earpiece and the car stereo.
So i figured, maybe you could use it in the same way, when you walk to the car enjoy the music trough your headset, and when you are in your car, click whatever button it is on your Rokr that activates the connection and simply click the icon to change the audio from your headset to the Rokr.
Click to expand...
Click to collapse
I don't think this will work this way for me. From what I could see the Rokr will not pick up the BT from the HBH-DS970 until and unless I power off the HBH-DS970. Just like my second HBH-DS970 could not get the BT passed to it until the first HBH-DS970 was powered off. But I'll go and check this out...
edit :
After reading your story about your Rokr again, i begin to believe there is something wrong with the BT portion in your Diamond (connection dropping, having different icons say different things about BT state). Your Rokr wants to make the connection by pressing the button, and that is how easy it should be.
That's how it works for me. I would recommend upgrading to the latest ROM, i downloaded it from the official HTC website.
I mentioned the exact filename with version number a few posts ago.
That way, you will be sure that software (BT stack) is o.k., i can confirm that in my case it does what it is supposed to...
Click to expand...
Click to collapse
I think that perhaps your situation is different. You mentioned that your "MBR-100 uses A2DP, my earpiece HFP". Yet AFAICT my HBH-DS970 uses A2DP and the Rokr also uses A2DP. Both are attempting to receive stereo music.
defaria said:
Define "different profiles" in this context...
Click to expand...
Click to collapse
I meant, e.g. if your headset used HFP and your Rokr A2DP, they could be connected at the same time. Now i read in your post they both use A2DP so the whole toggling trough different profiles solution is off the table..
defaria said:
What I'm asking is "Why not? Why this seemingly artificial limitation? Is is security concern? Did nobody think anybody might want to do this? Is it a hardware limitation? Is it a Bluetooth 2.x limitation?". It just seems silly to me to put a limitation like this for seemingly no particular reason. Ya know some people might want to actually share their music in like real time!
Click to expand...
Click to collapse
I don't know the reason behind that (share music in real time would be awesome, though) but i can think of one technical limitation, and that is bandwith.
If you set the bitrate too high you wil experience skips. When i discovered the highest possible setting without skipping, i even had to set it a bit lower because i use my earpiece simultaniously. The music played without skips, but as soon as i would turn the earpiece on it would start skipping.
It is also impossible to stream audio and transfer data via PAN. Both the connections are o.k. but te A2DP stream would stop until the data is transferred.
So i assume there would not be enough bandwith to stream audio to multiple devices..
defaria said:
But another thing that would make me go for the new ROMs is if I could get rid of the god awful Sprint Music Player (SMP or actually the HTC Audio Manager and its Today plugin)! This thing sucks! I usually use Pocket Player however the god damned SMP steals the AVRCP controls such that Pocket Player cannot get them. So I can't use Pocket Player and then have the Play/Pause button on my HBH-DS970 play or pause the SMP! You end up having two audio streams playing at the same time and the pause button does not pause Pocket Player! If there's a ROM out there that removes the silly SMP then I'm all ears!
Click to expand...
Click to collapse
Heh, i use Pocket Player as well Unfortunately i don't use AVRCP but i think that is a software issue. I've read somewhere else on this forum users having the same complaint. Did not see a solution there..
Question : is this sprint player integrated in TF3D? There is a tweak tool out there to remove tabs. I removed the music player tab.
The other solution would be to go for the updated ROM from HTC. I understand your worries concerning support after flashing but i have flashed every phone i had and had never any problems.. My (flashed) Wizard broke down once, and T-Mobile (my carrier then) repaired it without any cost..
I must say i don't know how Sprint handles these things (i live in Europe).
A good thing is it's a ROM upgrade from the official HTC website so i don't think you have to change SPL (which from what i heard, is the warranty-voiding process). But anyway the sprint player is NOT included..
defaria said:
I'm a little leary replacing the BT stack that's currently working pretty good (aside from the dropping problem) unless I can assure myself that I can re-install it if the new one doesn't work.
Click to expand...
Click to collapse
You can always perform a hard reset, the MS BT stack will be intact.. (maybe use Sprite backup before you install another stack, it works really well (i don't know if you have the program, it came with my Diamond))
defaria said:
I think that perhaps your situation is different. You mentioned that your "MBR-100 uses A2DP, my earpiece HFP". Yet AFAICT my HBH-DS970 uses A2DP and the Rokr also uses A2DP. Both are attempting to receive stereo music.
Click to expand...
Click to collapse
True, the idea of using the BT audio toggle is definately not going to work for you.
But, our situation has similarities! Like i mentioned, i use two MBR-100 devices. When one runs out of energy, i use the second one. They both use AD2P!
The process of changing the two is really simple, and i believe it should be as simple as that with your two A2DP devices.
This is how it goes wen i change the two :
- music is playing on my Diamond, sound goes to MBR100 #1.
- i power off MBR100 #1 (or it runs out of energy), A2DP connection closes, music keeps playing but now from the phone speaker.
- i power up MBR100 #2, press the button on it, it establishes A2DP connection and the music keeps playing, sound goes to MBR100 #2.
Simple as that, i don't even have to awake or touch the Diamond. Now i believe it should be possible that it is that easy for you too..
defaria said:
I usually use Pocket Player however the god damned SMP steals the AVRCP controls such that Pocket Player cannot get them. So I can't use Pocket Player and then have the Play/Pause button on my HBH-DS970 play or pause the SMP!
Click to expand...
Click to collapse
I may have found something that can help with the AVRCP problem..
LINK
Unfortunately i can't test it but it looks promising..
TheMusicMaster said:
I may have found something that can help with the AVRCP problem..
LINK
Unfortunately i can't test it but it looks promising..
Click to expand...
Click to collapse
This doesn't work. The "plugin" sounds like the plugin that even Conduit already offers for older versions of Pocket Player. And the new version of Pocket Player has this already built in. The problem is it's ineffective as something in the HTC implementation is usurping the AVRCP thing. See Bluetooth in 3.7 on Conduit's forum and AVRCP not working in PocketMusic and PocketPlayer ! here in this forum.
It may be that disabling the Sprint Music Player (really HTC Audio Manager) tab and guts will solve the problem and that may be in the HTC original ROM. I don't think you gave a direct pointer but I will research this later tonight.
Pointers to how to do a hard reset on the HTC Touch Diamond such that I can get back to the original ROM from Sprint would be appreciated (I seem to recall if you burn a ROM onto the phone then a hard reset goes off of that burned ROM not the original ROM. And no I have no backup product).
This is the link to the thread where you can download the TF3D Config program to remove the music tab.
You can perform a hard reset by pressing the vol-down key and enter button simultaniously (then power up), but you can only use this to restore the current ROM you are running to its initial state.
So you are right, you can use a hard reset to restore your Diamond to factory settings now (might be useful if you just want to experiment with other BT stacks and end up with the original BT stack not working), but if you flash your phone you can't go back to its original state unless you have that factory ROM.
But, since the ROM i mentioned comes from the official HTC site, i guess when it comes to support if you ever need it, you can always put on your innocent face and say "was i not supposed to do that?"
TheMusicMaster said:
This is the link to the thread where you can download the TF3D Config program to remove the music tab.
Click to expand...
Click to collapse
Yes, except http://forum.xda-developers.com/showthread.php?p=2852736 (page 101 post by scottsimon1979) states:
scottsimon1979 said:
I am unable to get this running on my Sprint Touch Pro. I get a message saying An unexpected error has occurred in Diamond TF3D Config.exe.
When I go to details, this is what I get:
Diamond TF3D Config.exe
NullReferenceException
at f.m()
at Diamond_TF3D_Config.frmMain.v()
at System.Windows.Forms.Form.OnLoad()
at System.Windows.Forms.Form._SetVisibleNotify()
at System.Windows.Forms.Control.set_Visible()
at System.Windows.Forms.Application.Run()
at a.a()
Any ideas?
Click to expand...
Click to collapse
To which another guy said he's having problems and if you look even further down that thread I said "Me 3!". So TF3D Config does not work for us unfortunate Sprint HTC Touch Diamond owners...
You can perform a hard reset by pressing the vol-down key and enter button simultaniously (then power up), but you can only use this to restore the current ROM you are running to its initial state.
Click to expand...
Click to collapse
Forgive me but no button is labeled "enter". Which one is the "enter" button?
So you are right, you can use a hard reset to restore your Diamond to factory settings now (might be useful if you just want to experiment with other BT stacks and end up with the original BT stack not working), but if you flash your phone you can't go back to its original state unless you have that factory ROM.
Click to expand...
Click to collapse
Yes, hence my request for the Original Sprint Factory ROM...
But, since the ROM i mentioned comes from the official HTC site, i guess when it comes to support if you ever need it, you can always put on your innocent face and say "was i not supposed to do that?"
Click to expand...
Click to collapse
You're in Europe aren't you? Things are different here in the States. Sprint doesn't take to kindly to you saying "was I not supposed to do that?". Their answer would be "of course you can't do that - your warantee is now void".
It's clear to me that the HTC phone and the Sprint branded phone are not one in the same. For one the back is different. Two, it's branded with the Sprint logo all over it! 3, it has the "Sprint Music Store", something I highly doubt a European HTC Touch Diamond would have. Forth, there is no radio! None, nada, caput! I downloaded the Radio cab and installed it - even hooked up the wired headset since it needs that for an antennae - nada. I also saw postings that Sprint's phone doesn't do radio. Now I could complain to Sprint saying the HTC site boasted of an FM radio to which I'm sure Sprint will merely say "Well that's HTC. We are not HTC. Our site and our advertising never said anything about an FM Radio". Additionally the time on the home page is different. Finally, tools such as TF3D Config tool just bombs out as noted above. No, to me it's clear the Sprint phone is not the same as the HTC Touch Diamond from HTC itself.
It's not like I haven't been downloading and installing things that obviously Sprint wouldn't like. I got things like a Transparent Clock, Remove [Sprint] Logo, Flip Clock and Advanced Config and TF3D Config. I even played with downloading the HTC Audio Manager and the HTC Audio Manager Today Plugin. All of these things were cab files that I could easily, and relatively safely install, try and uninstall should it not work correctly. I'd love to "install a new Bluetooth stack" if that were doable. But burning a whole new ROM and permanently severing any hope of "support" from Sprint - voiding the warantee... Well I guess I'm not exactly there yet but you're right - I'll probably have to end up doing that.
Still it would be nice if I could get the original Sprint ROM and the HTC ROM and play around with at least a little hope of being able to go back.
Oh, and BTW, aside from the "Volume Down and Enter while powering up" thing, I recall having some .exe that I ran on my PC that did the burning of the ROM to the phone. IIRC there was some other sequence to get it to receive the ROM. Ah yes I documented this on my blog:
Once you have a ROM you run the installation process. First you need to get your phone in "Bootloader" mode. This means, on my phone, that you hold down the power and voice record buttons at the same time while you perform a soft reset. Now here's the tricky part: The screen appears to be black but if you look really carefully you'll notice it says "Serial". You'll probably have to look at it in the light and move the phone from side to side. Why the secretly displayed with no backlight screen is beyond me.
Click to expand...
Click to collapse
What's that sequence for the HTC Touch Diamond? And do these ROMs then install to this phone in "bootloader" mode?
O.k., i didn't realize your Diamond was different from mine. I figured, if we both have the same hard and software, and it works here, it has to work for you too.. When i was with T-Mobile, i got a branded HTC Touch, but this branding was nothing else then they put their T-Mobile logo on the device, and they modified WM6 so that everything has pink icons (no wonder i flashed it whitin a week ).
But the hardware was identical to original HTC devices.
I recently moved to a less urban part of the country, where there is no T-Mobile reception so i had to switch carrier, and when i switched i got the Diamond. This new carrier was Telfort, and they didn't even brand or lock the device. The only reason i upgraded the software is because i read the performance would be better (and it is )
So i see now, your situation is really different..
defaria said:
Forgive me but no button is labeled "enter". Which one is the "enter" button?
Click to expand...
Click to collapse
It's the round button in the middle. But you can also go to => settings => system and click "clear storage".
defaria said:
But burning a whole new ROM and permanently severing any hope of "support" from Sprint - voiding the warantee... Well I guess I'm not exactly there yet but you're right - I'll probably have to end up doing that.
Click to expand...
Click to collapse
One thing you can do before you decide to flash is see at HTC's website if there is an update for your device.
Before you can download the ROM, you have to fill in the serial number from your Diamond. Then you will know if they even have an update for your device.
When you fill in the serial number you will automatically get the right update. I even got the update in my own language (i'm dutch).
defaria said:
Still it would be nice if I could get the original Sprint ROM and the HTC ROM and play around with at least a little hope of being able to go back.
Click to expand...
Click to collapse
I'll keep my eyes open.., if i ever see this ROM i'll pm you.
defaria said:
Oh, and BTW, aside from the "Volume Down and Enter while powering up" thing, I recall having some .exe that I ran on my PC that did the burning of the ROM to the phone. IIRC there was some other sequence to get it to receive the ROM. Ah yes I documented this on my blog:
What's that sequence for the HTC Touch Diamond? And do these ROMs then install to this phone in "bootloader" mode?
Click to expand...
Click to collapse
No, it's actually quite easy. It is an .exe you run from your desktop when activesync is connected. Click "next" a couple of times, wait +/- 7 mins until the progress bar reaches 100% and you're done... Nice website btw. I see you play the guitar as well
TheMusicMaster said:
But the hardware was identical to original HTC devices.
I'll probably end up just flashing to the HTC ROM. Hell most of my updates so far have been to get it to be more HTC-like as they did a nice job (and Sprint has screwed it up). I just need to get some extra spare time if you know how that is....
This new carrier was Telfort, and they didn't even brand or lock the device.
Click to expand...
Click to collapse
Sigh. Someday the cell phone industry in the US will wake up and stop with this stupid branding, tickering and locking people in! Cell phone companies! It's easy - just provide good service and you're have customers coming out of your ass! But I digress (and rant!)
Nice website btw. I see you play the guitar as well
Click to expand...
Click to collapse
Thanks. Haven't played guitar in years now. Music's not what it used to be (i.e. respected) or at least not here in the US. Again, different market...
Oh, another thing, BT related. It's been frustrating but lately when I get a call I cannot answer it with the BT headset! Looking at the phone and trying Menu: Turn Hands Free On is grayed out! Quite honestly I'm no longer used to having to hold a phone up to my ear! It's damn inconvenient! Just this weekend my sister called and I was outside detailing my car a bit listening to a radio show. I go to answer the phone and it drops the BT connection! So I'm talking to her and I cannot continue my work - my car will have to wait. So I go back inside and turn on the speaker phone to listen and talk while I fiddle with the Bluetooth settings attempting to get the damn Turn Hands Free On thing to work. I turn off BT on the phone. I turn of the BT headset I have. I turn them both one - nada. I go into Settings: Bluetooth: Device and Refresh to see if the Hands Free got toggled off. Nope. I delete the device and re-add/re-pair it. Nothing. Nothing I did would get it so that I could switch to using my BT headset so I could get back to doing my car. What causes Turn Hands Free On to gray out when BT is on and the device has Hands Free toggled on? I mean shouldn't that mean that I can use Hands Free from that device? BTW, of course, a soft reset of the phone fixes the problem but by then it's too late! It's damn frustrating. And god damn it, I ask you, how hard is it to get BT working correctly?!?
Now when I get a phone call my music stops, the BT disconnects and the phone starts ringing on the speaker. I answer it and the screen goes blank and the speaker phone kicks in. Damn this is convenient! This is exactly what I want my phone to do! It anticipates my every need! NOT!!!
(Now I know somewhere there was some setting to turn off the screen when the phone picks up but I can't find it anymore. And the dropping of the BT and instead automatically going to the speaker phone - so everybody else can hear - is just unacceptable! Really, this should not be this hard! Designers of phones and their UI's - WAKE UP! Geeze!).
Click to expand...
Click to collapse
OK, I'm fed up. I'd say that just today alone I had to turn on Bluetooth after it turning itself off like 15 times today. Just going to the grocery store whenever I hit the pause button then attempted to resume playback, BT was lost - 3 times on the less than 1/2 mile drive back to my house! The HTC ROM and no support from Sprint can't be any worse!!!
I will need to spend some time getting the ROM and then preparing properly to take this step. Usually I'd do this on the weekend but my daughter's in town for the weekend so it might be the week after. I've heard about the HTC Original ROM but are there any better ones? Remember, BT reliability is high on my list. And if I can find a ROM that allows me to remove - completely gut - the HTC Audio Manager tab so that Pocket Player can have a chance at AVRCP then I'm all ears!!!
I promise to write a full report on my experiences, hopefully documenting the problems I currently have and the hopeful solutions the new ROM will give - or just the new set of problems which is probably more likely...
This has almost gotten me to the point of writing my own Bluetooth stack though something tells me that the reason it works so badly now is probably because the Bluetooth specification is overly complicated and not very well defined...
And thanks everyone for listening to my ranting and not coming down too hard on me. I'm frustrated and sometimes vent. Thanks for understanding...

play an audio on voice call Rooted Android 9

I have a task for one of school project to allow play a short audio on voice call. I've been searching for long time for a solution to that problem or at least a starting point, I found some topics that talking about modifying the kernel of android to allow this but I have no idea how to do The project needs to be done in latest android versions ( 10 or 9) with Samsung devices (S10 for example ) which are rooted Thank you
FearNaiim said:
I have a task for one of school project to allow play a short audio on voice call. I've been searching for long time for a solution to that problem or at least a starting point, I found some topics that talking about modifying the kernel of android to allow this but I have no idea how to do The project needs to be done in latest android versions ( 10 or 9) with Samsung devices (S10 for example ) which are rooted Thank you
Click to expand...
Click to collapse
what is it exactly that youre trying to accomplish?
youdoofus said:
what is it exactly that youre trying to accomplish?
Click to expand...
Click to collapse
Thank you for your replay. I'm trying to stream an audio clip through the system on voice call. Means when I am in phone call talking to someone, I can play a short audio clip that can be heard by the other party too. The project is for personal purpose, it means only me that can be using that option, so I can root my device or make a custom rom, I just need to know how i can do that things
Thank you
FearNaiim said:
Thank you for your replay. I'm trying to stream an audio clip through the system on voice call. Means when I am in phone call talking to someone, I can play a short audio clip that can be heard by the other party too. The project is for personal purpose, it means only me that can be using that option, so I can root my device or make a custom rom, I just need to know how i can do that things
Thank you
Click to expand...
Click to collapse
you shouldnt need root to have an apk play audio at the push of a button while on a phone call at the same time
I also search for this feature.
The best would be, if it would be possible to play internal Audio directly via the Voice-Uplink (this is the Audio which goes to the other person), and the Speaker.
Is it possible to Mix the Voice-Uplink Channel, to contain the Microphone input (the Voice) and the Media Audio-Channel?
(That's like the "Stereomix" on Realtek Audio-Cards on PC https://www.google.com/search?safe=...i29i30j0i10i30j0i10i203j35i362i39.7TvHA0zwoeQ)
profi_fahrer said:
I also search for this feature.
The best would be, if it would be possible to play internal Audio directly via the Voice-Uplink (this is the Audio which goes to the other person), and the Speaker.
Is it possible to Mix the Voice-Uplink Channel, to contain the Microphone input (the Voice) and the Media Audio-Channel?
(That's like the "Stereomix" on Realtek Audio-Cards on PC https://www.google.com/search?safe=...i29i30j0i10i30j0i10i203j35i362i39.7TvHA0zwoeQ)
Click to expand...
Click to collapse
this is what i was expecting android to do automatically, and in many cases it does it seems. I was reading about this a bit last night and saw where people were indeed able to play something on the speaker of their phone and have the very same phones mic and play on the phone call for both parties to be able to hear. It was a native in the phones where users reported this ability. It was even reported to work on some older samsung phones. I still have a S4 and could test it out, if i remember to do it (my license plate says IFORGOT). @AthieN this is the thread i was talking about
youdoofus said:
this is what i was expecting android to do automatically, and in many cases it does it seems. I was reading about this a bit last night and saw where people were indeed able to play something on the speaker of their phone and have the very same phones mic and play on the phone call for both parties to be able to hear. It was a native in the phones where users reported this ability. It was even reported to work on some older samsung phones. I still have a S4 and could test it out, if i remember to do it (my license plate says IFORGOT). @AthieN this is the thread i was talking about
Click to expand...
Click to collapse
So basically, they told me that they used to record uing Tinyalsa library (tinycap exactly), but they couldn't do it with samsung S10, when I search I found that there is not tinyalsa included in that phone. So I was wondering if I can add it directly to the system or I have to make own rom for that ?
I hope @AthieN can give us hint on that. Thank you both of you for your help
profi_fahrer said:
I also search for this feature.
The best would be, if it would be possible to play internal Audio directly via the Voice-Uplink (this is the Audio which goes to the other person), and the Speaker.
Is it possible to Mix the Voice-Uplink Channel, to contain the Microphone input (the Voice) and the Media Audio-Channel?
(That's like the "Stereomix" on Realtek Audio-Cards on PC )
Click to expand...
Click to collapse
That's seems a good idea but idk if applicable to android devices or not
Sorry for the late reply. This used to be possible, but not since API 20 or 21 due to security concerns.

Categories

Resources